Search Documents

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By J. Russ, C. L. Clark

For many years attempts have been made to develop a laboratory test that would serve to indicate the proper temperatures to be used in the various hot-working applications to which metals may be subjected as they are being processed from the cast ingot to the desired finished products. That these attempts have not been very successful is indicated by the fact that most of the temperatures in use today in these operations have been developed over a period of years by trial and error. In other words, the selection of the proper temperatures for the hot-working of metals is generally an art rather than a science. Our knowledge with respect to the behavior of metals at elevated temperatures has been greatly extended during the past several years. While most of the work in this field has been done at proposed operating temperatures of equipment, rather than at processing or fabricating temperatures, one outstanding fact has been developed, which is applicable to the entire high-temperature range; that is, that the rate of deformation to which the metal is subjected is of the same order of importance as the temperature. The failure to properly recognize this fact has greatly retarded the development of a suitable laboratory test for determining hot-working temperatures. Influence of Rate of Deformation on High-temperature Properties It is not the intent of this paper to survey all the work that has been done On the effect of deformation rate On the properties of metals. The importance of this factor, however, was shown by Zay Jeffries' as early as 1919, when he called attention to the existence of the so-called equicohesive temperature and to the effect of certain factors on the location of this temperature' Fig. I is a diagrammatic sketch showing the effect of temperature On the relative strength of the crystals and grain boundaries and the type of fracture that will res depnding On the location of the test, or Or temperature with respect to the equicOhesive temperature. Since the type fracture varies, it also follows that at temperatures below the equicohesive temperature the major deformation occurs in the grains: while at temperatures above, the deformation results either from the movement of the grains with respect to each other or recrystallization of the strained material occurs almost instantaneously, producing new crystals at the fracture. As previously indicated, it is an established fact that the position of this equicohesive temperature for any given metal is dependent On the deformation rate' For example, in 0.15 per cent plain carbon steel the location of this temperature under

Jan 1, 1947

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,' 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental Lurig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.2 In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,1 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental rig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.* In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

By R. E. Gilchrist, R. R. Harvey, M. R. Dean

A simple and rapid three-component analysis procedure has been developed for use in fluid-flow studies. The method is based on refractive index measurements, combined with refractive dispersion measured between the Ha and H wave lengths. The procedure requires. calibration curves for the three-fluid system. The only restriction on the fluids employed is that only one be an aromatzc or olefinic compound. Individual sample measurements require only a few minutes. Composition results within the limits of accuracy required for fluid-flow analog studies are obtained. INTRODUCTION The simultaneous analysis of three-component mixtures is a problem often encountered in fluid-flow analog systems. In petroleum production research, the problem is usually encountered in experiments on the displacement of fluid from a porous medium. In the case of immiscible displacement, simple volumetric measurements of the produced fluids are usually sufficient, the analog fluids often being the actual reservoir fluids themselves — oil, water and gas. However, modern secondary recovery of petroleum sometimes involves production under miscible conditions, in which the oil is displaced by liquefied petroleum gas which, in turn, is displaced by dry gas. Since this type of displacement is done under conditions of pressure and temperature that are not easily reproduced in the laboratory, studies are often performed with analog fluids at essentially atmospheric pressure. Since the number of samples taken during one of these experiments is usually quite large, the time required for analysis becomes an important factor. In the past, the difficulty of conventional analysis has been avoided by the addition of various tracers to one or more of the components, or by the use of a tracer fluid as one of the components. With these techniques, a relatively large amount of analytical time is still required. Moreover, in the case of added tracers, the tracer material may migrate in part to one of the other fluids, may be adsorbed on the solid surfaces of the model, or may introduce side effects not characteristic of the prototype fluid. The substitution of a tracer fluid for one of the components can severely limit the choice of analog fluids. Optical refractometry provides a rapid and economical method of analysis of two-fluid systems or of monitoring small changes in composition of an essentially one-component system. Refractometric methods are capable of high degrees of accuracy, require only very small samples and can easily be adapted to automatic methods. They are not generally applicable, however, where three or more fluids are present over wide ranges of concentration. The method of three-component analysis described here has three essential characteristics. 1. It is based on refractometric measurements and thus preserves all of these desirable properties. 2. It does not make any stringent demands on the choice of fluids that can be analyzed. 3. It is capable of accuracy sufficient for fluid-flow analog studies. THEORETICAL The difference in the refractive index of a substance at two different wave lengths of light is known as its dispersivity. When the difference is taken between the specific refractions at the two wave lengths, the quantity is referred to as the specific dispersivity. Specific refraction was defined empirically by Gladstone and Dale1 as r = n-1/d....[1] where n is the index of refraction and d is the density. The definition is given more correctly by the expression r =n2-1/n2+1 1/d..........(2) 1References given at end of paper. MICIFTV OF PETROLEUM ENGINEER JOURNAL.

By Stephen Royce

[PAGE Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine (TP 2000 by JOHN W. VANDERWILT, Min. Tech., May 1946. Discussion by STEPHEN ROYCE and the Studies of the Design of Shaped Explosive Charges and Their Effect in Breaking Concrete Blocks (TP 2157 by GEORGE B. CLARK, Min. Tech. May 1947. Discussion by PHILIP B. BUCKY, V. H. CLARK, E. D. GARDNER, M. H. HAWKINS, H. L. WALKER, and the author) 2 See TP 2377, Min. Tech., May 1948 for discussion of San Manuel ProsPect (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the authors)] Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine STEPHEN ROYCE•-It is interesting to note from B, Fig 2, how closely the subsidence limits approximate to the 60° angle of draw, which is so commonly found to rule in large scale rock subsidence. The tension cracks shown at B are commonly found in the initial stages of subsidence movement and spread like a halo about subsidence limits as movement extends. These tension cracks usually grow into escarpments later on. Apparently from the illustrations and description given, a system of vertical fractures is the predominating weakness in the wall rock at Climax, and therefore both tension cracks and escarpments are prevailingly vertical in attitude. The illustrations in Mr. Vanderwilt's article seem to conform to the general rule that yield by subsidence is heralded by tension cracks which foreshadow the appearance of the subsidence scarps which are both described in the paper and shown in Fig 2. The difference between the B side and the A side of Fig 2 is apparently caused mainly by the vertical fracturing which controls subsidence at Climax as compared to the relatively homogeneous rock formation at A upon which the original figure in Peele's Handbook was based. The draw at B is exactly 60°, while the draw at A is a little flatter. The influence of the vertical fractures explains the difference. The surprising feature is the relatively small deviation from the general 60° draw line, which is about the average of rock subsidence experience. The influence of local fracture systems, faults and bedding in controlling subsidence all the way from extremely low angles of draw to vertical is rather fully discussed in the Peele's Handbook article referred to. The more illustrations of subsidence there are published the better will be our knowledge. The general principles are pretty well established. The wide local differences reflect the effect of local conditions. This paper is a very valuable contribution to the subject, and for the benefit of the mining industry, it is to be hoped that there will be many more such clear and concise presentations. Particularly block caving is apt to be of greatly increasing importance in the future of a mining industry that must meet high labor costs. More examples of block caving from small scale to large scale operations like those at Climax will serve a vital need. JOHN W. VANDERWILT (author's reply)-I would like to thank Mr. Royce for his discussion; however, in his comments the meaning of subsidence, draw and tension cracks is not entirely clear. As used in my discussion of subsidence at Climax, subsidence refers to movements involving appreciable downward displacement. Tension cracks indicate only

Jan 1, 1947

By Sven Fornander

An account is given of the way in which a new process for desulphurization of hot metal is carried out at a Swedish blastfurnace plant. In the process powdered burnt lime is used as a desulphurizing agent in a rotary furnace. Results are given. IN a paper by Kalling et al.* the fundamentals of a new process for desulphurization of hot metal using powdered burnt lime as a desulphurizing agent were outlined. The purpose of the present paper is to give a brief account of the way in which this process is being carried out in practice by Surahammars Bruks AB, Sweden, and of the results obtained. + The hot metal from the blast furnace is tapped into a ladle of 15 tons capacity and transferred to a rotary furnace, a simplified drawing of which is given in Fig. 1. The rotary furnace has a total length of about 160 in. and an outside diameter of the rings of about 130 in. The furnace is in a horizontal position, with its rings placed on four rollers, and can be rotated by a driving mechanism at various speeds of up to 34 rpm. The rotary furnace and its driving mechanism were designed and constructed at Surahammar. The hot metal is charged into the rotary furnace through the opening to the left in Fig. 1. See Fig. 2. An addition is then made to the furnace consisting of finely ground burnt lime amounting to 2 pct of the weight of the hot metal as well as 0.5 pct of coke breeze. After the additions are made, the furnace is sealed to the atmosphere by means of two lids and set in rotary motion at a rate of 34 rpm. The sulphur in the hot metal is rapidly absorbed by the lime added, the time of treatment needed is normally 30 min. The process is then stopped, the lid is removed, and the furnace is lifted up by a crane and used as a tilting ladle for pouring the metal into the pig-iron molds, Fig. 3. Process Metallurgy The hot metal charged into the rotary furnace has a composition which usually lies within the following limits: C, 3.70 to 4.10 pct; Si, 0.80 to 1.80; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.060 to 0.200. Figs. 4 and 5 give examples of the changes in hot metal composition taking place during the treatment in the rotary furnace. As will be seen from the diagrams, the sulphur content of the metal decreases very rapidly during the first 10 min of treatment from about 0.100 to about 0.020 pct S. During the following 20 min, the sulphur content goes down slowly to about 0.005 pct S. The carbon and silicon contents of the metal decrease by about 0.10 pct each during the treatment. The manganese and phosphorus contents remain unchanged. Thus, if the process is started with an iron of the composition given above, the finishing composition of the metal usually lies within the following limits: C, 3.60 to 4.00 pct; Si, 0.70 to 1.70; Mn, 0.40 to 0.80; P, 0.025 to 0.030; and S, 0.002 to 0.020. The chemical reaction taking place during the process can be written:

Jan 1, 1952

By C. W. Burrows

The burden a man can endure depends on its magnitude and the number of times it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude of the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary streessses. While we are unable to formulate the law between the magnitude of repeated stresses necessary to produce rupture and the length of time during which these alternating stresses may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which! to a first approximation, is exponential. In other words, F = Ce-t where F= magnitude of alternating stresses; t= time for which stresses are continued; C = constant, which depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered, the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics of any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 1, 1922

By R. E. Robbins, H. R. Brager

THIS note describes an unusual result obtained in an electron microscope investigation of cavities produced in commercial type 304 stainless steel irradiated in a thermal reactor (ETR) at 290°C to a high neutron flu-ence, 6 x loz1 n per sq cm. The analysis of the steel used is given in Table I. The unusual result is that the calculated quantity of helium gas produced by transmutation during the irradiation, 12 ppm, is less than one-tenth the amount of gas necessary to balance the surface tension of the observed cavities produced in the steel during ETR irradiation. Therefore, the cavities would be expected to behave like voids; however, they behave like "gas filled" bubbles. The maximum quantity of helium produced in the steel by B" transmutation was 8 ppm. In addition, the amount of helium formed by (n, (1) fast neutron reactions with the major alloy constituents and nitrogen was calculated to be 4 ppm based on the tabulated differential or effective fission-averaged cross sections of elements in type 304 stainless steel irradiated in typical thermal reactors.', In previous investigations concerning commercial austenitic stainless steel irradiated in a thermal reactor, the amount of helium gas calculated to be produced by transmutation has always been significantly greater than the amount calculated on the basis that the bubbles were gas filled, PPs= 2y/R. The balance of the gas was assumed to be in bubbles smaller than could be detected on the electron micrographs. Accordingly, the bubbles were attributed to helium produced from transmutation of impurity boron by thermal neutrons. These bubbles were not uniformly dispersed in the matrix but were located principally at grain boundaries, or were radially positioned around a few precipitates located in the matrix and at the grain bundaries., 4 Voids have also been observed in austenitic stainless steel irradiated at high temperature to high neutron fluences in the EBR-I1 and Dounreay Fast Reactors. The voids were uniformly distributed throughout the matrix. The amounts of helium gas produced by transmutation during these irradiations were less than one-tenth the amounts needed to balance the surface tension of the voids formed by the fast reactor irradiation. The fast reactor results are quite analogous to those reported here for the ETR irradiated steel. Electron microscope examination of the fast reactor irradiated material after a 1 hr postirradiation annealing at 900°C disclosed that essentially all the voids had been eliminated. The authors stated that the voids had developed due to the high concentration of vacancies produced during irradiatin., 6, ' The microstructure of the ETR irradiated material as-tested at 75O°C, Fig. 1, contained about 2 X lot5 cavities per cm3 with an average diameter of 110A. With the Van der Waals b correction and y = 1500 ergs per cm2, 300 ppm He would balance the surface tension of the observed cavities. Stereoscopic examination of the electron micrographs showed that the cavities were neither preferentially located near the grain boundaries nor highly concentrated at specific regions or precipitates. The cavities were nearly uniformly distributed throughout the matrix, on dislocations and at grain boundaries. These observations imply that the cavities were not the sole results of B'O

Jan 1, 1969

By L. J. Dijkstra, R. J. Sladek

IN earlier work the effect of manganese on the general behavior of nitrogen in iron was the subject of a careful examination by Fast.' Part of the investigation was made, in collaboration with one of the present authors (L.J.D.), by using the internal friction method. This technique, which has been described elsewhere,' showed some significant changes in the properties of Fe-N alloys by the addition of a small amount of manganese namely: 1—Under standard conditions the maximum of the nitrogen peak in pure iron appears around 20 °C and the half width is about 27 °C. By addition of 0.5 atomic pct Mn a general broadening of the internal friction peak occurs. The half width is increased by about 9°C. Moreover, a shift of the maximum of about 5°C toward a higher temperature takes place, Fig. 2. 2—The precipitation of nitrogen from the supersaturated solution, measured, e.g., at 200 °C, was inhibited by the addition of the amount of manganese given in effect 1. The broadening of the nitrogen peak was confirmed in more recent work3 on samples which were prepared from Westinghouse Puron iron. The effect of manganese on the rate of precipitation, however, was much less striking than in the earlier work' based on Philips high purity iron. Theory To explain the first change in properties just referred to, effect 1, the following two assumptions were made:' First, every manganese atom in sub-stitutional solid solution creates around it six interstices located between an iron and a manganese atom, as is evident from Fig. 1. These interstices, conveniently called Fe-Mn interstices, have for nitrogen a free energy level which is AG* lower than the normal Fe-Fe interstices between two iron atoms. For such low concentrations of manganese as 0.5 atomic pct, the possibility that two manganese atoms will be nearest neighbors can be disregarded. Second, it is assumed that in addition to the normal relaxation time TFe at least one new relaxation time, Mn, Fe, enters in the phenomena which is associated with the elementary diffusion jumps between a Fe-Mn interstice and an adjacent Fe-Fe interstice. Fig. 1 gives schematically the free energy for a nitrogen atom as a function of its position along the line ABC. A tentative analysis of the nitrogen peak in a 0.5 pct Fe-Mn alloy based on these assumptions has been made in Fig. 2. The dotted curve with a maximum at 22°C is caused by jumps between Fe-Fe interstices, the dotted curve with maximum at 32°C by jumps between an Fe-Mn and an Fe-Fe interstice. The two effects added together give the dash-dot internal friction curve for the alloy. In the following these two components will be referred to as the normal peak at 22°C and the abnormal one. (The small secondary peak at

Jan 1, 1954

By M. A. Dayananda

Based on the Kirkendall frame of reference, a method is proposed for the determination of atomic mobilities of all the diffusing species in a multicorn-ponent system with a single diffusion couple. The method is based on an atomic mobility model developed on the concept of negligible interactions among the intrinsic fluxes. It is shown in the model that mobilities can be obtained directly from the cumulative intrinsic fluxes past the Kirkendall interface. The proposed method replaces the need for a prior determination of interdiffusion coefficients far the calculation of mobilities. Relations between intrinsic diffusion coefficients and mobilities are derived and the mobility calculations are illustrated with diffusion data in Cu-Zn-Mn alloys at 850°C. ThE concept of "intrinsic flux" with respect to a fixed lattice was introduced "i Darken1 to explain toa Kirkendall effect2 demonstrated by the motion of inert markers during isothermal diffusion in single-phase binary solid solutions. Based on this concept, intrinsic diffusion studies have been made in various binary metallic systems3,4 employing such a lattice frame of reference, commonly referred to as the Kirkendall interface. Similar approaches, both theoretical and experimental, have been presented5"10 to study intrinsic diffusion in multicomponent systems. Based on the direct integration of Fick's law extended to multicomponent diffusion, Philibert and Guy8 proposed a method for the determination of intrinsic diffusion coefficients. For an n-component system, this procedure requires an experimental study with (n — 1) diffusion couples, all having their Kirkendall interfaces at the same compositio;, where n(n — 1) intrinsic diffusion coefficients are defined. This technique has been employed for ternary diffusion studies by Dayananda and Grace" and Guy and Leroy.11 A different approach is recommended by Ziebold and Cooper,12 who have derived relations between interdiffusion coefficients and atomic mobilities employing fluxes referred to the local center of volume. Their analysis is based on the simplifying assumption of negligible interactions among intrinsic fluxes. This assumption has been considered satisfactory for dilute solutions.5"7 The use of this analysis for the calculation of mobilities requires an initial determination of interdiffusion coefficients with a set of diffusion couples having intersecting diffusion paths. It is the purpose of this paper to propose a method that would permit a direct determination of mobilities of all components of a multicomponent system from a single diffusion couple. This method is based on a mo- bility model developed with diffusion fluxes referred directly to the Kirkendall interface, generally identified by inert markers. gen erall, like that of Ziebold and Cooper,12 employs the simplifying assumption that the flux of each component relative to a fixed lattice is caused only by the driving force of its own chemical potential gradient. THE KIRKENDALL INTERFACE Inert markers are employed in diffusion couples to locate experimentally the position of the Kirkendall interface. They are initially placed at the weld interface for "sandwich" couples, or at the original vapor-solid interface for vapor-solid couples. Studies of marker motion in binary systems3'4 with both types of couples indicate that markers remain in a plane of constant composition and move with this plane para-bolically with time. Parabolic marker movements were also observed in ternary Cu-Zn-Mn couples by Dayananda and Grace.10 It is reasonable to expect a similar marker behavior even for diffusion couples with a higher number of components.

Jan 1, 1969

By W. E. Hess

AT the Vesta mines of Jones & Laughlin Steel Corp. on the Monongahela River, 35 miles south of Pittsburgh, JCM Joy continuous miners and 6-SC shuttle cars are used for pillar extraction in the Pittsburgh seam. The entire output of the mine goes into coke production for blast furnace operation. Because this coal, which has high metallurgical qualities, is close to the place where it is ultimately used and because supplies with these properties are being rapidly depleted, complete recovery is essential wherever possible. With the introduction of the continuous miner into the Vesta mines, therefore, it was necessary to plan a project which would facilitate development and provide for future total recovery. Use of continuous miners under varying conditions has necessitated changes with regard to roof action, method of development, method of pillar attack, and innovations in mining. In the following pages these changes will be discussed. Prior to the introduction of continuous miners the Pittsburgh seam at the Vesta mines averaged 72 in. of mineable coal, overlain with 12 to 16 in. of draw-slate, which weathers on exposure to air and is not firm enough to be held in place. Immediately overlying the drawslate is a wild or rooster coal, very irregular in thickness, varying from 12 to 30 in. Above the rooster coal the strata consists predominately of shales or lime shales and sandstone. Just before the introduction of continuous miners in the Vesta mines, however, a definite change took place in the character of the roof structure overlying the coal seam, see Fig. 1. Thickness of laminated roof immediately overlying the rooster coal varies with localities and introduces a problem in roof control. In fact, a set of eight main entries being developed in Vesta NO. 4 mine entered an area with so difficult a roof structure that management considered abandoning the section altogether. In this locality the roof consisted of thin alternate layers of roof coals and shales, with an occasional irregular seam of slick slate, the whole being laced with slips, and the coal itself being cut by clay veins and spars. In an effort to overcome some of the difficulties, roof bolting was introduced in 1949. This made it possible to recover coal from an area which otherwise would have been economically unmineable. There have been very few roof bolt failures. When conventional machines were replaced by continuous miners there were changes in the development of butt entries. By these changes it was hoped: 1—to speed development, 2—to provide as much solid coal as possible for the machine on retreat, 3—to avoid the necessity of crossing entries already driven, 4—to facilitate ventilation, 5—to provide a roadway for shuttle car haulage which would eliminate the necessity of running through doors or curtains, 6—to provide better roof control by increasing the distance between the center lines of entries, and 7—to provide more coal when the machine was in position to load.

Jan 1, 1956

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel' that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

By W. M. Weidel

While electric lamps both of the cap and hand type are being introduced into many mines requiring the use of safety lamps, the oil-burning safety lamp is still used in the great majority of cases, and even where the former are used the latter must continue to be employed when testing for gas. It is not the intention to discuss here the relative merits of the two types, but simply to give a comparison of the illuminating effect or candlepower of several kinds of ordinary safety lamps used for general work and for testing. Few data have been published in recent years on this subject and because of this it is hoped that the following information may be of some interest and value. The lamps tested were in all cases of standard size and in good condition, all practically new, and were selected from a collection of about 100 with a view to obtaining results on as many different common types as possible. With the exception of the gasoline-burning lamps, five different oils were used in each lamp to determine whether particular oils were suited to particular lamps and whether there was any great difference in the illuminating power of the different oils, or whether some oils would maintain their illuminating power better than others throughout a working period of 8 hr. No attempt was made to determine the amount or cost of oil burned by each lamp, but the condition of the lamp, wick, glass, and gauzes was noted after each test. Description of Apparatus Used The candlepowcr was determined with a Weber photometer, Fig. 1, which consists of a tube A containing a movable milk-glass screen adjustable by the milled screw B. The distance of this screen from the standard light at C is read on the scale attached to A. The standard light consists of a benzine lamp so arranged that the height of the flame may be adjusted exactly by observing it against a scale in the lamp box through an opening in the front. The lamp to be tested is placed at D so as to illuminate a milk-glass screen in the holdcr at E. At the intersection of the axes of tube A and sight-tube F are placed two 45' prisms with their surfaces in contact so that the light from D may pass through with-

Jan 1, 1917

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley's second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

By D. J. Carney, R. L. Stephenson

M. O. Holowaty (Inland Steel Co., Chicago)—Messrs. Stephenson and Carney should be commended on the presentation of this very interesting paper. They have introduced new ideas on sampling of sinter and have thereby made a valuable contribution to the qualitative evaluation of sinter. The paper undoubtedly presents a novel approach to the problem of sinter sampling and this is to be regarded as its main value. Sampling of sinter from the pallets prior to the discharge is by no means new. This sampling procedure was used in the past by Philbrook; Hamilton and Ameen and others. The sampling basket used by the authors of this paper, however, permits one actually to obtain a good sample of the sintering mixture. The basket which can also be described as a removable pallet goes then through the entire process of sintering and thus offers a sample which is positively representative of the batch in question. The authors' method of evaluating physical properties of sinter seems to be not altogether clear, however. It is felt that the following points should be clarified: I—In the section describing the shatter test the authors state that a 5-lb sample was used in the actual tests. There is no mention of the initial size of sinter particles used and the method of obtaining this 5-lb sample from the sinter cake weighing about 100 to 120 lb. It is also surprising that the sample was dropped from a height of 3 ft instead of the conventionally used 6 ft. Unfortunately there is no mention of the number of drops to which the sample was subjected. 2—The tumbler test used by Messrs. Stephenson and Carney in testing the samples of iron ore sinter was performed in a standard ASTM coke tumbling drum. The drum measures 3 ft in diam and is equipped with two 3-in. lifter bars. The distance of fall in this testing drum is identical with the distance used in the previously described shatter test. The number of drops in the tumbling drum is approximately double the number of revolutions. The basic difference then between the drop-shatter test used by Stephenson and Carney and the tumbling test seems to be the number of drops to which the sample is subjected and the abrasive action to which the sinter particles are exposed in the rotating drum. In any case, the choice between the shatter test and the tumbler test seems to be only a matter of taste and convenience. 3—The authors of the paper state that "in order to insure getting results that were representative . . . the entire sample obtained by means of the sampling basket was used as the starting material for the tumbler test. If the sample broke in pieces, all the pieces were used regardless of their size." The initial size of the material is known to be a very important factor, influencing seriously the final size of the particles. This should be particularly important in case of hard sinters. It seems also very troublesome and inconvenient to charge 12-in. cubes of sinter weighing about 100 lb into the testing drum. This could be eliminated by taking a standard fraction of somewhat smaller particles.

Jan 1, 1954

By B. Ramaswami, Y. Nakada, R. Schaefer

EARLY investigations1 of the tensile properties of fcc single crystals did not reveal the easy glide region of crystals with axial orientations inside the standard stereographic triangle. With the production of high-purity metal, a region of easy glide became known1 Consequently, modern work of fcc single crystals ordinarily uses high-purity metal. In order to determine whether further purification of aluminum beyond 99.992 pct purity would result in significant alteration of the tensile properties of single-crystal specimens, metal was zone-refined and crystals grown from the purified material were compared to crystals grown from the original material. Some similar studies were made of gold and silver crystals. Aluminum. The material to be zone-refined was cast into bars 1/4 by 1/2 by 8 in. A zone, approximately 1-1/2 in. in length, was passed over each bar eighteen times at a rate of 6 in. per hr. Melting and stirring were carried out by an induction heater under a vacuum of approximately 10"5 mm Hg, the metal being held in a graphite container. he last 3 in. of each processed bar were then cut off and discarded. No quantitative determination of purity was made, but the effectiveness of the zone refining was tested by a method first suggested by Walton, Tiller, Rutter, and winegard3 depending on the relation between cell structure and impurity content. Rutter and Chalmers4 have shown that a cellular substructure is associated with the presence of impurities during solidificatibn, and have shown how solute rejection at the freezing interface can lead to such an association. Thus the observation of cells gives evidence of impurities being present. To look for cells, the last quarter of a zone-refined bar was cut off, remelted, and grown rapidly into a single crystal. It was then heavily electropolished and thermally etched.~ Cells were revealed by the presence of many parallel rows of etch pits. The same process was carried out with material from the first half of the bar, but no cells were detected. These observations give evidence that a significant amount of impurity material was moved to the "dirty" end of the zone-refined bars. Further indication of purification was obtained from recrystallization experiments. It was found that, after cold rolling to a 97 pct reduction in thickness, the material from the pure end of the bar re-crystallized at room temperature, but the material from the "dirty" end did not. Other investigators6 have previously reported that zone-refined aluminum recrystallized at room temperature. The purified material was cast into 1/4 by 1/4 in. bars, and seeded crystals were grown in a (100) orientation and in a single slip orientation where the Schmid factor is m =2. The crystals were then cut to the desired length, annealed for 24 hr at 610°C, furnace-cooled, and etched in Tucker's etch. The crystals were tested in a floor-model Instron machine, using a gage length of 4 in. and a strain rate of 1/2 pct per min. The resulting curves are shown in Fig. 1. It is seen that the differences between the curves for zone-refined and original-purity materials are small. These differences are within the scatter observed for crystals of the original purity. In particular, the zone refining does not significantly affect the onset of the different "stages" of the curves.

Jan 1, 1964

By B. W. Frazier

IN the numbers of the Engineering and Mining Journal of June 27th and July 11th, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced to the same standard of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given -by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of the pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part of the furnace, by the dissocia¬tion of carbonic oxide, is again converted into carbonic oxide or

Jan 1, 1875