Search Documents

By G. R. Speich, R. A. Oriani

The rate of coarsening (Ostwald ripening) of copper precipitate Particles in an a-iron matrix has been studied in three Fe-Cu alloys containing 2.3, 4.0, and 5.4 wt pct Cu in the temperature range 730° to 830°C. The kinetics of Ostwald ripening ohevs the law as deduced by Lifshitz and Wagner so that matrix diffusion controls the process. The equilibrium shape of the particles is that of rods with hemispherical caps, and is due to the BOTH Lifshitz and slyozov and wagner3 have recently solved the complex problem of determining the rate of coarsening of an assembly of precipitate particles. Both workers, although using somewhat different mathematical approaches, arrive at the same equation for the relation between the mean radius 7 of a distribution of spherical particles and the bulk solubility co, diffusivity D in the matrix, large anisotropy in the copper/a iron interfacial free energy (y,/y, = 4). A Lifshitz -Wagner equation, modified for both the nonsphericity of the diffusion field and the reformulation of the Gibbs-Thomson equation for the case of nonsphencal particles, is derived. Using the modified equation, the calculated values of the mean radius are smaller than those observed by a factor of about one -half. absolute temperature T, gas constant R, surface free energy y of the precipitate/matrix interface, and the time t of aging: where V, is the molar volume of the precipitate and v is a stoichiometric factor. Wagner's treatment is restricted to the case of spherical particles growing in a liquid matrix where strain energy is not a factor. Lifshitz and slyozov have discussed the effect of anisotropic particle shapes and internal strains on the rate of coarsening. Oriani4

Jan 1, 1965

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson's3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan' have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.' An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.' A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.' from Wagner's kinetic expressions for internal oxidation:

Jan 1, 1969

By B. M. Larsen, T. E. Brower

INTRODUCTION THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slagmetal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is .partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the continual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process, In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium, On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. PROBABLE CHEMISTRY OF DESULPHURIZATION Since there is little evidence that sulphur atoms in the iron solution are associated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* [(FeS) -, [FeS],[I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) = (CaS) + (FeO), [2] and, (FeS) + (MnO) ;:2 (MnS) + (FeO). [31]

Jan 1, 1948

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E Hunner,1 M. H Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice Details on any points of interest can be obtained through correspondence with the operators involved.† The iron ores of Minnesota, which have been formed through enrichment, of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high iii phosphorus, alumina and moisture The iron ores fall into two classes- (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite) The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high+manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges will have to be absorbed

Jan 1, 1942

By N. A. Zeigler

The present publication is a continuation of the work on gas analysis described in a paper presented before the Institute of Metals Division year ago.' While that paper was largely descriptive in character dealing with the various parts of the apparatus and method of operations the present one gives numerical data obtained as a result of a series c experiments with iron-carbon alloys. The apparatus and the method applied are essentially the same as previously described, changes bein only in minor details. Attention should be called to the fact that in the present work we ar dealing with the gaseous mixtures obtained as a result of vacuum meltin of various ferrous alloys. It should be understood that when the term "degasified sample" and "products of degasification" are used, the refer to the sample remaining after the vacuum fusion of the alloy an the gaseous products removed therefrom, respectively. The write does not wish to create the impression that the metallic products of thj process are absolutely free from any gaseous elements, nor that the gase obtained are present as such in the original sample. These two point are not yet definitely known and are subjects for future investigatior The point, however, which has been established beyond doubt, i that all the gases dealt with come from the metallic charge and ar present either in the charge as such, or are produced as a result of chemic: reactions going on within the charge. The suggestion that the gases an due to the reactions between the metallic charge and the refractor materials has no valid basis. General Procedure A series of iron-carbon alloys was prepared in a magnesia-line graphite crucible placed in a high frequency laboratory furnace open t the atmosphere. The materials used were Westinghouse electrolyti iron and Acheson graphite. Each alloy, after it was completely molter was kept in the liquid state for 10 min., cast into a small iron mold, an

Jan 1, 1929

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By H. F. Ameen, F. M. Hamilton

Results of a laboratory investigation of some sintering variables are presented. The effect on physical properties of mix component variation and rate of cooling of the sinter is illustrated by crush and tumbler test results and data of reducibility tests and microscopic examination of sinters are shown. The results of using solid additions in the mix to improve bed permeability are given. SOME of the variables encountered in the sintering of iron ores and their effect on sinter properties have been investigated at the Jones and Laughlin Ore Research Laboratory in Michigan. Ores requiring agglomeration before blast furnace utilization may be classed as coarse, intermediate or fine. Coarse iron ore is considered similar to a — 1/4-in. Mesabi wash ore containing some 95 pct of its particles between 94 in. and 100-mesh. Intermediate iron ore is considered similar to our New York State magnetic concentrates in which all the particles are — 20-mesh and about 60 pct are +100-mesh. Fine ores are considered as being at least 100 pct —100-mesh. This paper will deal only with the two coarser classifications. Most of the work has been done in a small experimental batch unit previously described in an AIME1 paper. Results being obtained form a basis for present and future trials in production sinter plants. It is expected that new production units that may be added in the future will benefit from laboratory studies. In general, the results reported here are obtained by laboratory study, but it is Experimental Sinter Machine: The laboratory sinter machine employed in the work consists of a chamber with 1 sq ft of grate area. It is mounted on

Jan 1, 1951

By Lendall P. Warriner, Blandford C. Burgess

Jasper County lies just north of the geographical center of Georgia, bounded on the west and north by the Ocmulgee River. The county seat, Monticello, is approximately 65 miles east-southeast of Atlanta and 40 miles north of Macon. It is served by the Macon-Athens branch of the Central of Georgia Railway Co. and by five paved highways converging from adjoining county seats. Farming and lumbering are the principal local occupations. About half the county is covered with pine and mixed hardwoods; a large part of the forested land is owned by the Soil Conservation Service of the Department of Agriculture in its Piedmont Land Utilization Project. The topography is one of gently rolling field and forest with occasional hills rising 100 ft or more above the creek beds. Though annual rainfall is in the neighborhood of 60 in., most of it falls in torrential downpours of short duration which tend rapidly to erode the red soil and convert the country roads to greasy tracks of red mud. History The pegmatites of Jasper County produced a small amount of mica in World War I. In World War 11, our Government's search for this strategic mineral brought to Georgia B. C. Burgess, then Southern Manager of Colonial Mica Corp., subdivision of Metals Reserve Corp., who noted on State Highway 83 the presence of pegmatitic material used as road metal. In 1944, after severing his Government connection and returning to private practice, Mr. Burgess investigated the source of the pegmatitic material noted on his previous visit and discovered that graphic granite pegmatite had been mined for the road metal. He secured mineral leases from the Soil Conservation Service and from private owners and began preliminary development work. By 1946 he had uncovered enough pegmatite to warrant an enterprise to undertake economic development of the feldspar. In March 1947, he conveyed his leases and interest to Appalachian Minerals Co., remaining with it as Vice President and General Manager. This company has carried on additional development, removing overburden by bulldozer and drilling the pegmatites uncovered. A modern and efficient feldspar grinding plant to produce 20 mesh feldspar for the glass industry was completed and placed in operation May 1, 1948. Geology GENERAL GEOLOGY OF ROCK TYPES OTHER THAN PEGMATITE Jasper County lies within the Appalachian Crystalline Complex and approximately 40 miles north of the "Fall Line," where the Upper Cretace-

Jan 1, 1950

This is a most interesting paper and some data in it are corroborated by work I did at Watertown Arsenal some time ago with iron powder. I would like to ask Dr. Wulff to say just a little more about the compressive and tensile stresses on the surface of compacts. JOHN WULFF (author's reply).-Our work has not yet been completed; although enough data have been obtained with cylindrical compacts of iron to permit some conclusions. Briefly, in a compact 3/4 in. high and 1/2 in. in diameter pressed at 48 tons per sq. in., the residual stresses on the surface measured by X-ray diffraction techniques are as follows: The radial stresses on top center and bottom of compacts are practically zero; the longitudinal residual stresses on the side walls are near the top quarter of the compact about seven tenths that of the yield point of mild steel in tension; at the center surface of the compact they are in compression and in magnitude about 0.3 that of mild steel in tension; near the bottom, they are practically zero. F. V. LENEL.?- I was particularly interested in the work that Messrs. Wulff and Seelig reported on the influence of lubrication on the density of parts. In connection with the work of the American Society for Testing Materials on determining the green density of a compact, we ran into considerable difficulty in getting reproducible results of green density determinations. It was much easier to get a reproducible green density when the lubricant was mixed with the powder than when the lubricant was applied to the die walls; particularly when the die was not perfect-i.e., if it was somewhat rough or out of round. In this case, it was almost impossible to get reproducible green densities when the die walls were lubricated, while it was not too difficult to get reproducible

Jan 1, 1946

This issue presents the first of several articles making up the Bump Symposium, which was held at the 1958 Annual Meeting of AIME. Other Symposium papers will appear in the September issue of Mining Engineering. THE term mountain bump describes the sudden rupture of one or more coal pillars under excessive stress. These bursts occur with varying degrees of violence and sometimes include adjacent strata, especially the bottom rock. Many failures do not develop enough violence to be dangerous and are regarded as an aid to coal production, but severe occurrences are accompanied by tons of flying coal, dense clouds of dust, and excessive gas emission. Such bursts sometimes throw heavy machinery several feet. Major factors to be considered in the problem are the nature of the strata above and below the seam and the depth of cover. Bumps are classified as to their nature, extent of damage, and point of occurrence, e. g., face bump, coal bump, high side bump, low side pavement bump, and district bump. The problem is extremely complex, and it cannot be over-emphasized that preventive measures, if they are to be successful, must be based on a thorough study of conditions in the individual mine. In western Canada, for example, the McGillivray mine, operating in a 9-ft seam at 2000 ft, has experienced severe bumps, but there have been no occurrences in the International mine, which operates in the same coal seam at 2400 ft, where the coal averages 17 ft thick. Differences in conditions governing the operation of these two mines are described in one of the following articles (see page 883). Again, most bumps in coal mines take place along pillar extraction lines, but at the Sunnyside mine in Utah they also occur a long way from active workings and sometimes in virgin territory. It is usual, too, for such failures to occur under fairly deep cover. But at Sunnyside, to cite only one instance, there have been disturbances along the main fault zone under less than 500 ft of cover. All too often conditions favorable to bumps are revealed only by actual mining—at Springhill No. 2 mine, drilling in roof and pavement strata disclosed a 60-ft sandstone bed after operations had started— and where extraction has advanced too far for preventive measures to be incorporated in the mining plan, districts have had to be abandoned. But in an era when premium ores are being rapidly depleted in the face of rising demands, abandonment is not easily justified. There must be systematic planning to eliminate coal mine bumps, insofar as this is possible. As in the Gary district of West Virginia (see page 888) much has been accomplished by planned operations based on known factors in bump control. But even this is not enough. Precise instrumentation is needed to indicate where bumps are likely to occur, and in both the U. S. and Canada stress analysis studies are being carried out with this object in view. These pages reveal the progress being made.

Jan 1, 1959

By S. Yukawa, M. J. Sinnott

A high resolution autoradiographic study of the diffusion of a nickel isotope (NP3) into copper in the temperature range of 650° to 925°C, with particular emphasis on grain boundary diffusion, has been made. The extent of grain boundary diffusion is a function of the grain boundary angle and the diffusion temperature. The ratios of the grain boundary diffusion coefficient to the lattice diffusion coefficient ranges from 104 to 105. The activation energy for grain boundary diffusion decreases with increasing grain boundary angle. STUDIES and reviews&apos;-8 of metallic diffusion have indicated that grain boundary diffusion is a common phenomenon but quantitative studies of the many variables involved are not numerous. The present work was concerned with determining the influence of the crystallographic orientation of the grain boundaries and the temperature on the extent of boundary diffusion of nickel into copper. The study involved essentially three steps: 1—the production of grain boundaries of known crystallographic orientation, 2—the determination of the extent of diffusion into the boundaries, and 3—the analysis of the resulting data in terms of the usual diffusion concepts. The grain boundaries investigated approximated the simple tilt variety having l° of freedom. They were produced by controlling the solidification from a melt of Cuprovac (a high purity vacuum-melted copper obtained from Vacuum Metals Corp.) of a pair of seed crystals so that the bicrystals of copper produced had a common <100> axis. By rotating one seed crystal relative to the other, a simple tilt boundary was produced. The angle of rotation between the two crystals is the grain boundary angle 8, or what is sometimes termed the misfit angle. In all, some 16 boundaries ranging from 2" to 72" in 5" to 10" steps were investigated. The crystallographic orientations were measured with the use of both X-ray and optical goniometric techniques. The <100> axes in the crystals were found to be parallel within 2" to 3" with the exception of one crystal (8 = 12") in which the axes were 6" from being parallel. All bicrystals showed evidences of sub-grain structures. Laue analyses showed that these subgrains differed in orientation up to a maximum of 2". Because of these variations, and some curvature in the boundaries, the grain boundary angles listed are actually average values and deviate from the 1 o of freedom boundaries. The stripping film technique of high resolution autoradiography was used to detect the diffusion of the nickel isotope into the grain boundaries of the bicrystals of copper. Kodak experimental permeable stripping film with an emulsion layer 5 u thick

Jan 1, 1956

C. H. MATHEWSON, New Haven, Conn. (written discussion *).-In a recent discussion of Dr. Jeffries&apos; paper on tungsten,1 J. C. W. Humfrey,2 after taking exception to certain of the author&apos;s ideas relative to the cohesion of A and C metal, expresses the opinion that future research is likely to develop a method of preparing tungsten possessing "mechanical properties in line with those of other metals." The present paper by Dr. Jeffries begins with a determination of comparative properties of tungsten, copper, and iron, in which much dissimilarity is apparent, and ends with a coherent explanation as to why much of this dissimilarity is natural and inevitable, thereby supplying theoretical means for visualizing the changing properties of metals in general, once certain fundamental facts are known. The author&apos;s reasoning is primarily from the standpoint of the amorphous theory and his principal achievement is the development of an idea f differential cohesion according to conditions of temperature, etc., between A and C metal (which was first plainly suggested by Rosehain and Ewen, in their papers on Intercrystalline Cohesion of Metals) along with associated ideas, so as to give us a really useful working theory. I have come rather reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties within the conglomerate, mainly because in no other way does it seem possible to account for observed changes of properties with temperature, etc. The very best illustration f the competency f the amorphous theory in this respect is seen in this and other recent papers by the author. All fractures through normal or healthy metal that have been preceded by deformation are supposed, by Dr. Jeffries, to take place either through the amorphous phase or at certain boundaries between amorphous and crystalline material; his reference to fractures, both members of which are similar in appearance and do not reveal a preexisting coarse-grained structure because of a coating of amorphous metal, indicates his preference for the former interpretation.

Jan 5, 1919

By Keith Leonard Sutherland

This paper is a study of the differential flotation of the sulphide minerals in the presence of salts of silver, lead and zinc. In practice, accidental activation due to these salts is more important than their use as reagents to replace copper sulphate. The general method of investigation has been based upon contact tests, the temperature of 35°C being chosen in conformity with earlier work. Potassium ethyl xanthate and potassium amyl xanthate were selected as collectors and pure sulphide minerals were used. The experimental procedure has been outlined in earlier papers and all solutions were kept carbonate-free.14 Contact, or spreading of an air bubble, at a mineral surface indicates the presence of an adsorbed collector film. Purity of Reagents The xanthates were purified in the usual manner.&apos; Neither the cyanide nor the sodium hydroxide solutions contained sufficient carbonate to give a precipitate with barium chloride solution. The silver sulphate was prepared from pure silver nitrate by evaporation with concentrated sulphuric acid until there was no evidence of brown fumes, This solution was diluted and the difficultly soluble sulphate washed with water so that unchanged nitrate was dissolved. The resultant crystalline powder was pure white. The lead and zinc salts were prepared by dissolving especially pure lead and zinc in C.P. nitric and sulphuric acid solution and the crystals drained. The standard solutions were checked by titration. It was felt desirable to use the sulphate radical wherever possible, but since lead sulphate was insufficiently soluble for the purpose of the experiments, it was necessary to use some other lead salt. A.R. copper sulphate was used without further purification. Results The results are presented in the accompanying figures; the areas of noncontact (nonflotation) are shaded in Figs. 8, 9, 10 and 11; in the remainder they lie to the right of the curve. Zinc Sulphate The curves in Fig. I are to be compared with those for Fig. 2, for which zinc sulphate is absent. This comparison shows that the influence of the zinc ion is usually small. Its influence is more marked, however, for chalcopyrite in the absence of cyanide. The influence of zinc sulphate is also marked for copper-activated sphalerite, for which tests were made only in the "absence of cyanide. The results are of importance in the separation of pyrite from copper-activated sphalerite when zinc sulphate is added in the lead flotation section (p. 204 of ref. I). Sphalerite does not adsorb the collector (i.e., become floatable) under the conditions chosen.

Jan 1, 1943

By R. P. Carreker, J. G. Leschen, J. H. Hollomon

THE external appearance of a crystal which has undergone plastic flow suggests that adjacent blocks of the crystal have glided bodily past one another along the slip planes. However, the great discrepancy between the shear stresses calculated to effect such a movement and those actually observed has for many years stimulated searches for more satisfactory interpretations of the slip process. Appreciable success in these efforts has been realized by assuming the presence in the crystal of various sorts of imperfections and by considering the consequences of the presence of these flaws when stress is externally applied, The theory that has received the most attention recently-that of dislocations-postulates the occurrence of small, mobile imperfections or dislocations which move through the crystal along the slip direction, each dislocation being attended by a local shear displacement of one interatomic distance. Thus only that portion of the crystal through which the dislocation has passed may be said to have slipped, Since each dislocation produces a displacement of only one interatomic distance, an avalanche or train of many dislocations would be necessary to account for the observed displacements of several hundred or thousand interatomic distances. The salient point of the theory of dislocations is the concept that a slip band does not suddenly appear in its entirety. On the contrary, it grows progressively across the slip plane as the individual dislocations successively appear and advance in a train through the crystal. However, the concept of growth is not intrinsic only to the theory of dislocations, since atomistic mechanisms other than that postulated by the dislocation theory can quite probably also describe the growth of a slip band. For instance, a slip band might resemble a disc-like interface that appeared and then grew continuously from a small size, producing a displacement that increased with the size of the disc, Whatever the precise mechanism, the concept of growth is in itself consistent both with -the observed low values of critical shear stress and with the experimental observation that slip bands. frequently do not traverse the entire crystal. The likelihood that slip bands grow implies that they must first be nucleated and that the initiation of slip can therefore be analyzed in terms of the general concepts of nucleation. Indeed, this suggestion was advanced1 several years ago, but the matter does not appear to have been further pursued. Recent advances in the theory of nucleations2,3,4 have encouraged such a treatment of the slip process. As will presently be demonstrated, this approach to the problem not only accounts successfully for the incubation periods that have been observed5,6 to precede slip but also predicts certain transient effects in the deformation process, The existence of these transients apparently has not hitherto

Jan 1, 1948

By G. V. Raymor, James T. Waber, I. Rex Harris

The lattice parameters of a series of fcc alloys of cerium and thorium were measured at 93 " and 298OK. Lattice parameters were also estimated for 171OK. Substantial deviations, y, from Vegard&apos;s law were observed. Although y was negative at the two higher temperatures, it was positive and large at the lowest temperature. A variety of models, which have been proposed in the past, were considered, and the calculated values of y were compared with the observed values. The best agreement was achieved with values computed with Friedel&apos;s equation. THE purpose of this investigation was to determine the effect of temperature on the lattice parameter and on deviations from Vegard&apos;s law of Ce-Th alloys. A large negative deviation from Vegard&apos;s law was first observed independently by Weiner, Freeth, and Raynor&apos; and Van vucht2 in the room-temperature lattice parameters of Ce-Th alloys that form a continuous series of solid solutions. This observation was confirmed by Evans and Raynor. The allotropy of unalloyed cerium was reviewed recently by Gschneidner, Elliott, and McDonald. In two subsequent papers,5" these authors reported the influence of various alloying additions on the y= transformation, which occurs below room temperature. Although other rare earths tend to stabilize the double-hexagonal phase, thorium, plutonium, and scandium as solutes tend to stabilize the normal fcc phase. With addition of sufficient thorium as a solute, there is evidence that the formation of is suppressed and it becomes possible to pass continuously with decreasing temperature from the room-temperature phase to the fcc a phase. Thus there is a closed loop which is similar in many ways to the y loop well-known in ferrous alloys. A closed field also occurs in the pressure-temperature "equilibrium" diagram of unalloyed cerium. Because of interest in the effect of thorium additions and their influence on the a and phases, lattice-parameter measurements were made at low temperatures on the fcc phase for a series of alloys ranging from 10 to 90 at. pct Th. The results obtained at three temperatures are shown in Fig. 1. Evans and Raynors analyzed the deviations from Vegard&apos;s law in Ce-Th alloys in terms of changes in the occupancy of the 4f electron level in cerium,

Jan 1, 1964

By Albert C. Harding

For several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. Description Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare wither-ite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. Occurrence All known commercially important barite deposits in the United States occur as re- placements or cavity fillings in schists, shales, limestones, dolomites, and quart-zites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. Table i—Crude Berile Sold or used by Producers in 1945 State Short Tons Arkansas................... 260.660 Missouri.................... 225.467 Georgia..................... 110,393 Tennessee................... 32,812 Nevada..................... 28,919 Other States............... 37,811 Total..................... 696,062 (&apos;other states,, included only california and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. Consumption The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium ------- chemicals Total 720,903 tons

Jan 1, 1949

By W. H. Durrell

DISCOVERY of large iron ore deposits in New Quebec and Labrador is, undoubtedly, one of the outstanding mining events of the twentieth century. To give an idea of size, the present concession is almost equivalent to a strip a mile wide around the earth at the equator. Importance of this iron ore area can best be appreciated by comparison to the famous Mesabi Range. On Mesabi, the area of favorable rock is 110 miles long and from 1 to 5 miles wide, with a, productive zone about 70 miles long. On the con- cessions the area of favorable rock in the Labrador Trough is 225 miles long and from 10 to 60 miles wide. In Quebec-Labrador, exploration already discloses that the productive zone is 90 miles long, with good chances of being extended at both ends. The Mesabi is covered generally by thick over- burden, and the iron ore deposits were found by T- test-pitting and systematic test-drilling. In Labrador and Quebec, most ore has been developed from a few surface deposits, and when it is considered that at least 95 pct of the area is covered by over- burden, and that there remains thousands of square miles of favorable territory still to be explored, it can be seen that the possibilities for developing additional ore are tremendous.

Jan 4, 1954

By W. M. Fox, D. P. Detwiler

IN the course of research on semiconducting inter-metallic compounds, it became necessary to obtain gallium metal of greater purity that that available commercially. Several methods were considered for further purification, including acid leaching,&apos; fractional crystallization,&apos; and zone-refining.3-5 The method of fractional crystallization was discarded as being equivalent to zone-refining in purification but inefficient in material and time. Both acid leaching and zone-refining were tried, and the method finally adopted is a combination of the two. The acid leaching technique has been reported&apos; to produce gallium in which no impurities are detectable spectroscopically. Although this method is very effective in removing oxides and surface contaminants, semiconducting material made of gallium subjected only to leaching indicated little reduction in the concentration of metallic impurities. Zone-refining, however, appears very effective in removing trace metallic impurities, but comparatively ineffective in removing the surface oxide film. Consequently, the method evolved consists of acid leaching to thoroughly clean the surface, followed by zone-refining to remove metallic impurities. The low melting point and relatively high thermal conductivity of gallium introduce some difficulty in maintaining frozen and molten zones in zone-refining. To accomplish this, it is found necessary to reduce the effective ambient temperature by circulating ice water in coils about the regions that are to be kept frozen, while heat is supplied to the molten regions by resistance coils. The power supplied to the heating coils is regulated by a constant-voltage transformer and a variable autotransformer. Both heating and cooling coils are mounted on a transite base. The gallium ingot is held in a closed pyrex tube sliding inside the heating and cooling coils, the reciprocating method of Tanenbaum et al. being employed to move the molten zones through the ingot at a rate of 2 in. per hr. This apparatus is shown in Fig. 1. The results of a spectroscopic analysis f a zone-refined ingot, as well as of the material as-received and after acid leaching, are shown in Table I. The ingot was 32 cm in length, and received 37 molten-zone passes, the molten zone being about 4 cm long. The only impurity found was lead, the following elements being reported also as checked but not found in the pure material: Al, Sb, As, Ba, Be, Bi, B, Cd, Ca, Cr, Co, Cb, Cu, Ge, Au, Fe, Mg, Mn, Mo, Ni, Pt, Si, Ag, Na, Sr, Sn, Te, Ti, W, V, Zn, and Zr. There thus appears no indication of pickup of Al, Mg, or Si from the pyrex boat as reported by Zimmerman&apos; in his fractional crystallization. Thus it appears that definite removal of lead from gallium occurs during the zone-refining process. It also may be concluded that a more sensitive analytical procedure than spectroscopy is required to evaluate quantitatively the purity of zone-refined metals. One such procedure which is proposed for use in the near future is the measurement of very low temperature resistivity. Although this will not identify the impurities present, it offers a very sensitive check of total impurity. Acknowledgment This work was supported by the Air Research and Development Command, United States Air Force.

Jan 1, 1956

By M. A. Scheil, S. L. Hoyt

About three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. † This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some comments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1. Degassing the Crucible One of the sources of error in vacuum-fusion methods has been the blank gases evolved from the graphite crucible after preliminary out-gassing. We have used 1750" C. as the outgassing temperature. This gives a base pressure at that temperature of less than 0.030 mm. after one hour and of 0.004 mm. on dropping the temperature to 1575" C. At lower extraction temperatures the base pressure is 0.001 mm. at 1050" C., 0.002 mm. at 1170" and 0.003 mm. at 1320&apos; C. Because of the size of our induction coil we are limited to this temperature, although it &apos;would be advantageous to use 1950" to 2000" C. Hamilton2, after outgassing at 1850" C. for 100 min., was able to reach a base pressure of 0.001 mm. for a temperature of 1700&apos; to 1725" C. This would give a blank corresponding to less than 0.00015 per cent 02 and 0.00005 per cent H2. Chipman and Marshall outgas at 2000" C. for one hour by using a special construction

Jan 1, 1937