Search Documents

By E. C. Nelson

An equation is derived for calculating approximately the solubility of nitrogen in an alloy steel over a temperature range from 1200" to 1900°C using data on the effects of alloys on the activity coefficient of nitrogen in iron at 1600°C. Calculated values are compared with experimental data. STUDIES involving the solubility of nitrogen in complex iron alloys have been aided by a system devised by Lanenberg for calculating the solubility of nitrogen in ternary and higher alloys of iron at 1600C using available data on the activity coefficient of nitrogen in binary alloys. Calculated nitrogen solubilities agree well with experimental determinations on complex alloys,' and the calculation procedure is useful when experimental data on specific alloys are not required. A method for extending calculations of nitrogen solubilities in alloy steels to temperatures other than 1600°C would be useful because of the paucity of experimental data in this area. Assumptions which must be made to permit this calculation introduce an element of approximation; however, the calculation is useful in cases where a large number of alloys and temperatures are under consideration, and the precision of experimental measurements is not required. The activity coefficient can be freed from the isothermal restriction of Langenberg's calculation if it is assumed that the solution is "regular". This is a reasonably good assumption for solutions of nitrogen in iron alloys, because usually they are dilute and the heat of solution is relatively small. The presence of large amounts of certain alloying elements would make this assumption less tenable.3 One of the properties of a regular solution is: when "f" is the activity coefficient of a solute and "T" is the temperature in OK. If the activity coefficients at temperatures T and T2 are denoted by subscripts 1 and 2 respectively: The activity coefficient of nitrogen in a complex alloy then can be calculated at any temperature from the sum of the effects of the other solutes on the activity coefficient of nitrogen at 1600°C. It will be convenient to incorporate this expression into an equation which will give directly the logarithm of the solubility of nitrogen at any temperature in the presence of alloys. Two constants, the solubility of nitrogen in pure iron at 1600 "C and the partial molar heat of solution of nitrogen in iron are required. The heat of solution value of 1400 cal at 1600 °C quoted by Kubaschewski and vans will be used. The accuracy of the calculation will suffer if the heat of solution should change materially with temperature. In the absence of experimental data on the temperature dependence of this quantity, it will be expedient to restrict the application of the calcula-

Jan 1, 1963

By T. T. Quirke, L. C. McCabe

The object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrainl was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.—Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may be used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indicative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.—Early in the present investigation several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maximum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the following paragraphs. Johannsen5 states the fundamental concepts underlying this procedure as follows: In general, in an isotropic medium light vibrates in all directions at right angles to the direction of propagation, and when it meets with another isotropic medium at an angle, part of the light is reflected and part refracted. It has been found that after reflection or refraction, the vibrations do not move with the same freedom in every

Jan 1, 1938

By J. T. Jones, H. V. Winchell

In the history of mining in this country there has been nothing exactly similar to the Mesabi iron-range in Minnesota, and the conditions there prevalent. Soft-ore mines are found in many parts of the country. In some the deposits are vertical, and are worked in open pits, or have been so worked, until it was found cheaper to go under ground. In other localities, the ore is scattered through clay beds in the form of hard lumps. These clay beds are sometimes excavated in open pits, and the ore separated by washing. On the Mesabi, the ore itself occurs in strata, and these strata appear quite flat to one standing upon the ground. The ore is soft in the main, and does not require much sorting to free it from foreign or deleterious substances. It is usually covered by the glacial drift-mantle, but occasionally passes beneath a capping of jasperoid rock called " taconite." The ore is twice or three times the thickness of the layer of drift lying upon it. This drift consists of clay, sand, and gravel, with occasional beds of large boulders. There is great difference of opinion among competent miners as to the cheapest methods of mining this ore. It is admitted that local conditions will govern largely ; but there is such a similarity among many of the mines that it seems possible to arrive at some general conclusions on the subject. A typical example of a Mesabi mine is found in the Biwabik. It is one of the largest, and is the most advanced in development. Not a single ton of ore has yet been shipped from this mine, but the expense of the explorations upon which the following description is based has exceeded $60,000. It is seldom that such accurate and complete exploration of a deposit of this magnitude has been possible in the space of time which has elapsed since the discovery of this ore-body. It lies in a new. region, and was remote from railroads until last August, yet, not only the width and length but the depth and quality of the ore-deposit have been learned, and the probable expense of' mining its 20,000,000 tons of ore has been closely figured. After careful consideration, the method of stripping and

Jan 1, 1893

By J. M. Gaines, C. H. Herty

IRon oxide (FeO) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating slags Previous Investigations The solubility of oxygen in iron has been determined by a number of investigators (see Table 1) but their effort's have been directed toward the

By L. W. Kempf

DURING the recent development of aluminum alloys for free-cutting screw-machine rod, it became desirable to know something of the solubility of lead and bismuth in liquid aluminum and in some aluminum alloys. The literature is not particularly helpful in supplying this information. These portions, therefore, of the constitutional relationships of aluminum-ismuth and aluminum-lead alloys were investigated by thermal analysis and by chemical analysis of samples taken from aluminum-rich melts in equilibrium with precipitated lead or bismuth. The solubility of lead and bismuth in some liquid aluminum-copper alloys was also investi-gated. Some consideration was also given to the solubility of these elements in solid aluminum. Among the earliest investigators of the aluminum-lead and aluminum-bismuth systems was Wright,1 who reported that melts of aluminum and lead formed two layers indicating limited liquid solubility. Under his conditions, the aluminum-rich layer was reported to contain 1.91 per cent Pb and the lead-rich layer, 0.07 per cent Al. Subsequently, Pecheau2 found that in aluminum-rich alloy melts with more than 10 per cent Pb three layers were distinguishable. He reported that the middle layer contained from 3 to 10 per cent Pb. He also found that the melting point of aluminum appeared to be lowered slightly by the addition of lead. Gwyer3 investigated these alloys and found evidence of a slight lowering of the freezing point of aluminum by the addition of either lead or bismuth. He found no evidence of solid solubility in either case and made no attempt to determine the liquidus curves. Hansen and Blumen-thal4 reported that the addition of lead distinctly lowered the solidifica-tion point of aluminum. They also found that bismuth lowered the melting point of aluminum. Guillet5 reported almost complete mutual immiscibility for the aluminum-bismuth alloys in the liquid state. Bohner6 examined the effect of various concentrations of lead and bis-muth on the electrical conductivity of aluminum. He found decreases in conductivity on annealing at 500° C. as compared with the conductivity of the same alloys on annealing at 300° C.

Jan 1, 1938

By H. H. Otto

Fourteen years ago, J. B. Warriner presented before the Institute a paper on anthracite stripping,' describing the progress of stripping in the Anthracite Region from its beginning with an old quarry stripping at Summit Hill, which was operated more than a century ago, through various types of strippings used in 1917. This paper will briefly review the status of anthracite stripping methods from 1917 to the present day and describe in detail the stripping operation of The Hudson Coal CO. at Clinton collicry. It is not intended as a review of the work in the district—that would require a much longer paper. History and Statistics Mr. Warriner said, in part: "The sizes of shovels have gradually increased until now 70 and 80-ton shovels are the rule and larger equipment is coming in." He also referred to a large electrically operated dragline which weighed about 225 tons and had an operating radius of 125 ft. In 1917, a number of strippings used shovels of various sizes, ranging up to the 60 Marion and Bucyrus 70-C railroad type. Material was hauled away in narrow-gage side dumpers, usually of 4 or 5 cu. yd. capacities. Star-type churn drills with 4-in. bits were generally used for drilling purposes. Since 1917 wages in the anthracite field; have increased, but the higher operating costs of strippings are now being successfully combated by continuous improvements in stripping equipment, such as the development of the caterpillar or crawler shovels, the use of larger cars, better drilling equipment, the introduction of shovels of increased capacity and the adoption, in a number of instances, of standard-gage equipment for transportation. In 1918 another large dragline was introduced in the southern fields, which had been in service in the Middle West and is in use today, dipping vertically about 180 ft. to raise coal out of a stripping. About 1918, small shovels with caterpillar traction were introduced. In 1922 the 6-in. well drills began replacing the 4-in. drills, with an attendant saving to the operators. About the same time A. E. Dick placed the first pair

Jan 1, 1931

By William Plank

IN PAST YEARS, engineering educators and others have been able to study the problems relating to en-gineering education in the United States with only inadequate and, frequently, inaccurate data at their command. For the first time there is now available fairly full and accurate information on this subject, gathered and compiled by the Board of Investigation and Coordination of the Society for the Promotion of Engineering Education. This board, of which W. E. Wickenden is the director, has for the past four years been carrying out fact-finding investigations into "the objects of engineering education and the fitness of the present day curriculum," under a grant of funds from the Carnegie Corporation of New York. Twelve bulle-tins have already been published by the board and others are in the process of preparation. The studies made, thus far, have been of the various phases of engineering education in general as well as of the major branches of engineering. Within the past year. the board has completed a study of mining engi-neering education by means of a questionnaire sent to members of the Institute. A special committee, con-sisting of Charles E. Locke, Allen H. Rogers and the writer, cooperated with the board in drafting certain parts of the questionnaire and in selecting the mailing list. Similar studies have been made through the mem-bers of the four other national societies. The results of these studies have been published only in mimeo-graphed form, therefore, in order to place the data before the members of the Institute an incomplete sum-mary of the replies to the A. I. M. E. questionnaire is here given. The full report will be available for distri-bution at the annual meeting in February. The questionnaire was sent to 306 members of the Institute, a proportion about equal to the proportion of the membership of the other national societies can-vassed; 152 members replied to the questionnaire, 55 per cent of whom had received college degrees in some branch of engineering connected with the mineral in-dustry. Forty-seven educational institutions were rep-resented in the replies. Seventeen different positions were held by the members who replied, with 24 con-sulting engineers at the head of the list, 20 managers, 16 superintendents, 11 presidents, 10 professors, 6 deans, and others.

Jan 1, 1928

By John Shelton

ONE of the heaviest burdens uselessly cast by our mineral land laws upon the holder of the title conveyed by a patent from the United States is due to the provision excepting known veins from land patented as placer. In many instances the expense of defending such titles from the assaults of the owners of lode locations made upon the theory that the veins so located were known to exist at the date of the placer application for patent has exceeded many times the value of the land in question. Neither the lapse of time, however long after the issuance of the patent nor repeated adjudications by the courts serve to quiet such titles or to prevent them from being questioned. In the passage of laws providing for the acquisition of title to the mineral lands of the United States, Congress provided that the title to known veins should not pass from the United States by a patent based upon a placer location. As construed by the courts, the law (Sec. 2333 R.S.U.S.) provides that the applicant for a patent upon a placer claim may, if any vein of sufficient value to justify the expenditure of money in its development is known by him to exist within the boundaries thereof, include in his patent application an application for patent upon the vein as a lode claim; and failure to do so is to be deemed a conclusive declaration that the applicant makes no claim to the vein nor to an area of surface ground extending for 25 ft. (7.6 m.) on each side of its middle or center. As to such vein and, such area of enclosing surface ground under the circumstances stated, the title remains in, the United States notwithstanding the issuance of a patent that purports to convey the entire surface of a described area and everything beneath it, excepting only the segments of veins the apices of which lie outside of such area. Such known veins with such area of enclosing surface ground are, of course, at any time, so long as they remain unlocated, subject to location and appropriation in the same manner as other veins upon the public domain. The history of the operation of this law in one district will serve to illustrate its effect generally throughout the mining regions of the United States. In the Butte district, the mineral that first attracted the atten-

Jan 8, 1919

By J. L. Shugert, W. C. Williamson

DUST control is receiving considerable attention today by most companies as is evidenced by the many articles, papers, and books written on the subject. ~~~t of the larger mining companies have given this subject close study and have established standardized methods of control. W. C. WILLIAMSON and J. L. SHUGERT, Members AIME, are Assistant Ventilation Engineers, Anaconda Copper Mining Co., Butte, Mont. San Francisco Meeting, February 1949. TP 2705 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 17, 1949. Permissible Limits: The question of permissible dust limits has been considered by medical commit-ties and various national conferences. Dr. Lanza, of the Metropolitan Life Insurance Company, Dr. Le-roy U. Gardner, of the Saranac Laboratory for the study of Tuberculosis, and Dr. Pancoast, of the University of Pennsylvania, have been members of these committees. A statement included in reports of some of these committees is as follows: Concentrations to which the dust must be induced in order to be safe have not been absolutely determined. There is evidence that a concentration of more than five million particles per cubic foot of a highly siliceous dust is dangerous. Therefore, it may be stated that it is desirable to avoid counts of more than five million particles of dust containing free silica to a high percent in working places. Table I gives the safe limits adopted by several state industrial codes. Table I. Safe Limits of Dust Concentration Limit Million Particles State Per Cu Ft Cal~fornia Silica (less rhdn 10 pct) 50 Silica (10 pct to 50 pcr) 10 Sllica (more than 50 pct) 5 New York Frcc silica less than 10 pet by weight of rock formation 100 Frec silica more than 10 Pct by weight of rock formation 10 Oregon Silica (over 40 pct) 5 Silica (20 to 40 pct) 10 Silica (10 to 20 pet) 20 Wisconsin 15 million particles, under 10 nicrons in longest dimension per cu ft of air, when the quartz content of the dust is 35 pct, variations in free silica content will make proportional inverse changer in this standard Close attention to dust concentrations has been given to mining operations, since these operations are frequently carried on at considerable distances

Jan 1, 1951

By David H. Browne

The use of coal-dust fired reverberatory furnaces, or indeed of rever-beratory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital. problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved. Reverberatory practice with our ores was, however, an unknown factor. As carried on in the West, on siliceous ores and concentrates, at least 25 per cent. of fuel was required, and even this ratio depended greatly

Jan 1, 1915

By Julian M. Avery

IN its dual role of pig-lion smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose During the past 10 years or more, improvements in blast-furnace technique and economy have, n fact, been directed primarily to increasing efficiency n the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace The net over-all result is a decrease n the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently amore than offset n value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements The purpose of the present paper is to suggest that, while progress has been made n this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure, i e , the "top pressure" under which the furnace is operated It is indicated that pressure operation may also be expected to result n concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Geo. H. Ashley

The following paper is intended to be suggestive only, and to open the way for discussion and further observation. Its preparation was requested only two days before the time limit set for the submission of the papers comprising this symposium. Thus no time existed for detailed studies, so it is largely a memorandum of such facts as have come incidentally to the notice of the writer in the study of coal in the field. The field study of sulfur in coal has received very little special attention or description from coal student's. The presence of sulfur concretions is noted in hundreds of descriptions, and certain benches of a coal bed may be described as "sulfury" or the presence and position of sulfur bands may be noted in coal sections in connection with sampling. It may be accepted that some sulfur is present in all coal. The amount varies greatly in different regions, in different beds, and in the same bed in different areas. The anthracite of Rhode Island comes the nearest of any coal known to the writer of being free from sulfur, several analyses of that coal showing less than 0.1 per cent. Subbitumi-nous coals in Colorado in a few places have close to 0.2 per cent. of sulfur on the dry-coal basis and in other states subbituminous coals approach this lower limit. Bituminous coals seldom run under 0.4 per cent. of sulfur on the dry basis, though in a few places dry bituminous coals in Colorado and Washington have between 0.3 and 0.4 per cent. The better known bituminous coals have almost everywhere over 0.4 per cent. The best of the Pocahontas and New River coals run close to 0.4 per cent., but there is very little commercial coal in Pennsylvania, Ohio, Indiana, Illinois, Kentucky, or the other states, that runs under 0.5 per cent. on the dry basis. From these minimum figures, the amount will range up to 5 or 6 per cent. or higher if visible sulfur is not excluded. It must be remembered that the usual analysis of a coal bed is not intended to give the total proportion of sulfur in the bed but the amount in the coal after the removal of the more obvious and larger sulfur masses. Professor Parr has already pointed out that, chemically, sulfur occurs in several forms: as pyrite, organic sulfur, sulfates, and possibly as un-combined sulfur. Sulfur in the form of sulfates is commonly the obvious result of the weathering of pyrite and may be found in the coal within .

Jan 1, 1920

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for' aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.' With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By W. H. Kantner

IN this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change sub-sidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the sur-face to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the east and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody-which is on the northwest side-is 600 ft. southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934

By S. Gilbert, G. R. Bailey

A further evaluation of the bomb-sampling method for determining the oxygen content of liquid steel is presented. The results of this study and their close agreement with the results of an earlier evaluation confirm the conclusion that the bomb-sampling method is valid for obtaining representative samples for the determination of the oxygen content of a liquid steel bath. WHAT constitutes the most desirable procedure for obtaining a sample suitable for determining the oxygen content of a liquid steel bath has been a controversial subject for several years. In 1952 Huff, Bailey, and Richards' described a modification of the bomb-sampling technique originated by McCutcheon and Rautio.' In both the modified and original techniques, a small cast-iron or steel mold containing aluminum wire and appropriately covered is inserted into the furnace, coated with slag, and then plunged into the metal bath. Upon entering the metal, the cover melts and a sample of the steel bath enters the mold. The data presented by Huff, Bailey, and Richards' indicated that reproducible samples could be obtained by their method. Furthermore, the oxygen analyses from samples obtained by their method agreed better with those from controlled laboratory experiments than did analyses from samples obtained by methods previously suggested for sampling large liquid-metal baths. Most techniques, other than bomb-sampling, require that a sample of liquid steel be removed from the furnace in a well slagged spoon and poured into an iron mold containing aluminum or into a massive copper mold for rapid chilling. Pouring in this manner requires that the sample pass through the air. The controversy, then, is somewhat as follows: Proponents of the spoon-sampling method and similar dip-and-pour methods feel that the introduction of a cold steel mold into a molten steel bath may result in a localized boiling condition that may deplete the steel of oxygen to a significant degree in the area where the bomb is introduced. Conceivably this boil could cause results that are, on the average, too low and nonrepresentative of the bath composition. On the other hand, samples that are spooned and then poured through the air may also be nonrepresentative because of oxidation by the atmosphere. The restrictions imposed in sampling with a spoon are much more stringent than those imposed when sampling with the bomb-type mold within the furnace. The spoon sample must be taken in a well slagged spoon, a requirement that depends on the condition of the slag in the furnace. Also, the samples must be poured as quickly as possible, without shaking the spoon and without allowing slag to enter the mold. The necessity of fulfill-

Jan 1, 1955

By Ralph Hultgren, David W. Mitchell

Magnesium alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600" to r 7o0°F.; the casting temperature, which depends upon the mold shape, is usually 200° to 300°F. lower. The process of superhcating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported1 that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results? As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted' project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. Materials and Methods The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesiun used in these alloys was of both carbothermic3 and electrolytic' origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200° to 1250°F., portions of approximately one pound each, were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21 † covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F. for 15 min., then . cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By John M. Gallow

Discussion of the paper of JOHN M. CALLOW, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2321 to 2339. R. H. RICHARDS, Boston, Mass.-I think there is one note which would be interesting to have recorded in connection with this paper, and that is another form of flotation machine. The Minerals. Separation machine has a vortex action, with a vertical shaft and a propeller. This new frother has been developed for the Copper Queen Co. at Bisbee, Ariz. It has a horizontal shaft and a paddle wheel for a frother. It has eight cells, I think, all connected underneath in one continuous tank, and the only separation of the cells is in the upper chambers where the froth is. When this paddle wheel goes around it throws out the froth and the sand goes to the bottom and drifts over from the first to the second cell, where it is paddled again, and comes out with its froth; the sand goes to the third cell where it is again beaten. In that way the sand is continually drifting toward the last cell, while each new froth remains in its own cell. You can see in the working of this machine just the same effect that you see in Callow's machine, i.e., the earlier cell has the darker or richer froth, and the latter has the lighter or poorer froth until you get to the farthest one-which has very little froth, and is very light. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-Speaking from the metallurgical standpoint, it is quite desirable, in many cases, that the oil be removed from the concentrate in order to facilitate the metallurgical work, and I think attention should be directed to the desirability of removing from zinc sulphide concentrates the oil which interferes with their subsequent roasting. The value of the oil is not large; in Mr. Callow's plant, for instance, it would be $20 a day, and it may be possible that a process might be developed which, within the limits of the value of the oil, would remove it, and thus facilitate the metallurgical treatment. LEONARD WALDO, New York, ,N. Y.-The question came up about a year ago as to why-Mexican crude was not an admirable oil for flotation. I have never heard any satisfactory answer to the question. The Mexican crude has the peculiar property of comparative freedom from dangers of fire, a very great reluctance to part with its water, and a specific gravity almost identically the same as water.

Jan 5, 1916

Edmund Gybbon SpilsbURy, mining and metallurgical engineer of international reputation, died suddenly of heart failure on May 28, 1920, in the New York Eye and Ear Infirmary, following an operation for cataract, which had been successfully performed a few days before. Mr. Spilsbury was one of the early members of the American Institute of Mining Engineers, which he joined in 1873. During all this time he contributed freely of his time and ability. He was manager of the Institute from 1885 to 1887, vice-president, 1893 and 1894, and president in 1896. He was also a member of the Engineers Club, of which he was president in 1916 and 1917, American Society of Civil Engineers, American Society of Mechanical Engineers, Institution of Mining and Metallurgy, Mining and Metallurgical Society of America, American Electrochemical Society and the Rocky Mountain Club of New York. He was a trustee of the United Engineering Society from 1916 to his death; a member of United Engineering Society Library Board from its organization in 1913 until his death, being its chairman from 1918 to January, 1920; a trustee of Engineering Foundation Board from 1916 until his death; and member of the John Fritz Medal Board of Award. He was also a member of the Division of Engineering of the National Research Council. Born in London, England, in 1845, Mr. Spilsbury went to Liege, Belgium, at an early age, where he received his preliminary education. For his technical education he attended the University of Louvain, Belgium, graduating in 1862, and later he took a practical course at Clausthal, Germany. In 1864 he became assistant engineer for the Eschweiler Zinc Co., of Stolberg, one of the largest miners and smelters of lead and zinc in the world at that time, and the next year he took charge of that company's mines and works on the Island of Sardinia. From Sardinia he went to the Atlas Mountains in Morocco. In 1867 he entered the service of McClean & Stilman, of London, and had charge of the construction of the iron gates for the Surrey Commercial Docks. In 1868 he was designing engineer with J. Casper Harkort, and had charge of most of the detail work of the Keulenberg Bridge in Holland, the Danube Bridge in Vienna, and the Rhine Bridge at Düsseldorf. In 1870 Mr. Spilsbury came to the United States to investigate the lead and zinc resources for the Austro-Belgian Metallurgical Co. After spending two years in this work, he resigned in order to practice in the United States, and he was the first to introduce the Harz system of ore

Jan 1, 1922

By S. J. Hardison

IN the fall of 1912, the appearance of water in the oil of the Nevada Petroleum Co., Coalinga, Cal., made necessary the installation of a dehydrating plant to reduce the water below the 3 per cent. limit prescribed by the agency. Unlike the mining industry, technical literature of the oil industry is limited and extremely unsatisfactory. Until the recent efforts of the Petroleum and Gas Committee of the American Institute of Mining Engineers, no concerted movement has been instituted to secure publication of papers dealing with the problems of the oil business, and because of the additional fact that dehydrating of oil has not been practiced in California to any extent up to comparatively recent time, it was found necessary to experiment in order to determine the most satisfactory plan for this purpose. It is easy to write regarding successful enterprises, but, while not so pleasant, it is equally desirable to write of failures so that others may be saved the loss incident to such investments. The water in this oil occurs both free and as an emulsion. Free water easily settles out, but the emulsion requires treatment. So far as can be determined, the emulsion consists of globules of water surrounded and enveloped by a film of, oil. Starting with this hypothesis, the theory has been evolved that in order to break up this emulsion the water must be heated at least to boiling point, when an explosion takes place destroying the globule. Unfortunately, this condition was not recognized in the installation of the first plant, which was planned on the following lines: A heater was arranged so that all the oil from the wells could be heated before reaching the shipping tanks, these being already fitted with coils for steam heating. Tanks were filled with about 4 ft. of water, live steam was turned into the coils and the water brought nearly to the boiling point, when the heated oil was run in. This for a time was partly successful, but the length of time necessary to apply this heat was too great for practical operating.

Jan 3, 1915