Search Documents

By Luis E. Vallejo

Experimental and theoretical analyses are presented to study the mechanics of growth and interaction for three inclined left-stepping, three inclined right-stepping and two inclined non-stepping cracks in a brittle material subjected to uniaxial compression. It was found that the non-stepping cracks did not interact and they propagated individually in a direction parallel to the uniaxial compressive stress. The propagating cracks formed in regions where tensile stresses developed. The left-stepping cracks interacted and formed branching cracks as a result of failure in tension of the material between them. Also, they propagated from their tips in a direction parallel to the uniaxial compressive stress. The right stepping cracks did not interact, but extended themselves from their tips following a direction parallel to the uniaxial compressive stress. The extended cracks formed in areas of compressive stresses.

Jan 1, 1984

By H. Jehn

The high-temperature oxidation of Pt metals results' in the formation of volatile oxides. The evaporation of which considerably increases the metal losses in oxygen-containing atmospheres when compared with high-vacuum or inert-atomosphere conditions. The paper describes gravimetric investigations carried out to determine the metal losses of polycrystalline samples of Ru, together with earlier studies on Ir and Pt at oxygen pressures of 10-3 to 1000 mbar and temperatures > 1000 °C. A strong pressure and temperature dependence is noted. Preliminary results of the oxidation of Pd are reported, too (665 mbar 02, 1100-1300 °C). The oxidation mechanism is discussed and the oxidation rates of Ru, Pd, Ir and Pt are compared with those of the other Pt metals Rh and 0s and of refractory metals.

Jan 1, 1984

By J. M. Karpinski, F. P. White, R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball, the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corp.'s Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about 50% without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1972

By E. H. Crabtree

Research on the iron ranges begins to bear fruit in big plant construction -Big coppers raise capacity, build at new Arizona, Michigan, Nevada, properties - Hydrometallurgy comes to fore with new uranium ore treatment and the Chemico process for nonferrous metals -

Jan 2, 1953

By T. H. Chin, R. W. Bartlett

A simple on-stream particle-size analysis method is presented that leads to a bulk-property single-channel device; although the concept can be extended to multi-channel sizing information. The method is based on continuously measuring and comparing the percent solids in the sample stream and in an internal-reference stream containing only undersize particles. A semipermeable hydraulic system is used such that the particle mass concentration in the internal stream can vary, and is always proportional to the undersize particle mass concentration in the sample stream.

Jan 1, 1975

By Shuichiro Okada

The Tamano Smelter, which is engaged in copper smelting by Flash Smelting Furnace with Furnace Electrodes (FSFE) has since 1982 revised its computer and associated control system for the purpose of greater energy savings, stable operation, and strict environmental control. This revision is bringing about a remarkable cost savings through greater reduction in energy consumption. This paper describes in detail the following: (a) outline of renewed process computer system, (b) approach to prediction model of FSFE based on data collection and its analysis, (c) actual examples of process control by using its prediction model, (d) future trends in the computer control at Tamano Smelter.

Jan 1, 1984

By Milan Lipensky

A variation of the longwall retreat system using friction props developed in coal mining is used extract a sedimentary manganese deposit at the San Francisco mine, Autlan, Jalisco, Mex. The Compania Minera Autlan, operating the mine, is partially owned by Bethlehem Steel Co. Roof control problems under a number of mining and strata conditions that defied uniform theoretical approaches led to a variety of experimental approaches that subsequently resulted in practical mining systems. Geologically, the area is one of considerable volcanic activity. The rocks are nearly flat-lying to moderately dipping conglomerate, tuff beds, inter-bedded porphyritic sills and felsitic lava flows. The formations overlying the manganese horizon are badly fractured and vary in thickness from 50 ft at the collar to 1400 ft in the deeper parts of the mine.

Jan 12, 1964

G. F. COMSTOCK (author's reply to discussion *).-The discussion of this paper has been of such volume and interest as to constitute in itself a sufficient excuse for the paper, even though the paper itself may have been as much in error as some of its critics have maintained. Mr. Howard does not appear to realize some very practical facts that the opponents of his theory have advanced. Among these are: the coarsely crystalline fracture of the nucleus of a transverse fissure, so different from the smooth fatigue break around it; the occurrence of fissures in large numbers in certain heats or rollings of rails, while other heats or rollings do not develop them; and the much smaller proportion of transverse fissures found in rails rolled .from reheated blooms as compared with direct-rolled rails. These facts are not explained by Mr.

Jan 6, 1919

By Thomas N. Walthier

ROSPECTING for uranium in the East is hampered by the lack of bedrock exposure due to extensive overburden and residual soil. But, despite the problems of this physiographic province, it has not been ignored in the search for radioactive materials. Since 1951 both the U.S. Geological Survey and the Atomic Energy Commission have had field parties in the eastern U.S. Tempo of private prospecting is increasing, and many discoveries have resulted. AEC work so far has been concentrated in the areas of most numerous discoveries-Pennsylvania, New Jersey, and New York. Accounts of uranium mineralization in the eastern U.S. are found in the old literature and one site in the Mauch Chunk area of Pennsylvania has been known since 1874. In 1949 McKeown examined the original occurrence there and found another southeast of the town. The deposit appeared to have commercial possibilities and a short period of production began in July 1954

Jun 1, 1955

By R. H. Migliaccio, M. B. Kahle

The railroad haulage system was started at Kennecott's Bingham Mine in 1906 and has remained a prime mover of ore and waste for the succeeding sixty years. As the stripping ratios increased contract stripping on the upper levels of the mine was introduced employing truck and shovel methods. The ore production then was 90,000 tpd. Analysis of expanding the ore production to 108,000 tpd revealed that the increased ore production and continually rising stripping ratio would result in waste production requirements that exceeded the capacity of the rail haulage system above 6290 level. The advent of larger haulage trucks (65-100 tons) in the early 1960's made available to the Bing- ham Mine economic and operating factors which showed truck haul- age to be the best replacement for rail haulage on the upper levels of the mine. As part of that analysis it was concluded that company stripping would replace the contractor stripping in the top area of the mine.

Jan 7, 1973

By D’Arcy A. Shock

In this year's review, the concept of solution mining has been expanded to include total solution as well as the technology of leaching, or partial solution methods. Leaching methods continue to make strides in the processing of metallic minerals, particularly in copper and uranium production. No quantitative data are available on the increase of leach operations; however, it is known that there were more systems installed in 1969 and that the estimated 15% of U.S. domestic production of copper produced in 1968 was by leach methods.1 While the number of publications appearing during the year were few,2,3 there were special sessions in this field at the AIME Annual Meeting and SME Fall Meeting in 1969 and more scheduled for these meetings in 1970. Significant areas that should be mentioned are: the continuing interest in bacteria to convert sulfide sulfur to acid thus reducing reagent costs in both copper and uranium sulfide ores, the exploration of leaching agents other than common mineral acids or alkaline solutions,4,5 kinetic studies of leach mechanisms and the development of microfractures for increased leach solution penetration by use of chemical or atomic explosives.6,7

Jan 1, 1970

By S. Webster, M. Karmis, C. Haycocks

Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to the recovery, cost and safety of mining the subsequent seams. This paper describes the ground control mechanisms involved in mining through a passive subsided zone or all actively subsiding trough. Data were extracted from case studies, primarily from the Appalachia region, for construction of empirical models to predict interaction problems that can occur in overlying seams. Inner-burden thickness, innerburden lithology, percentage extraction, lower seam height, time and overburden were analyzed to determine their effect on upper seam damage. Magnitude of upper seam subsidence was incorporated, together with a broad classification of rock types, to predict the type and range of damage that can occur in the upper seam. Results are summarized in graphically and nomogram form for use in. engineering design.

Jan 1, 1984

By N. R. Adsit

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from offman:"

Jan 1, 1967

By Charles E. Wait

The old laboratory at the School of Mines was among the notoriously bad ones, being situated in apartments of the main collegebuildings not originally intended, and conspicuously unfit, for the use to which they were put; while, as in many of our schools and colleges, the assaying was done in the basement of the college. Prominent among the disadvantages of such an arrangement are insufficient light, poor ventilation, and little or no provision to carry off offensive gases. It is not my intention now to present a complete description of this building. I wish merely to call attention to a few points in its construction and equipment, which may prove of interest to those who contemplate erecting buildings for snch work, and who may be, as we were in this instance, limited as to funds. In this laboratory every room is well lighted; all rooms used by students are well ventilated, and are provided with closed hoods for

Jan 1, 1887

By W. J. Millard

Owing to a moratorium in the drilling of crown-land leases in Trinidad during the year of 1931, only 40 wells were spudded in during the first eight months as compared with 110 during the same period in 1930. Nevertheless the production will show an increase of about 400,000 bbl. over that of 1930. An estimate is given in Table 1. Since the oil produced in 1930 was 9,418,907 bbl. and that in 1931 probably will be 9,853,976 bbl., the year 1931 probably will see an increase of about 4.6 per cent. The gross production of crude oil in the colony has increased steadily year by year, with the exception of 1919, when there was a slight decline. A tabulated statement was given last year.' The Petroleum Times of March 21, 1931 (p. 413) gives the total production of 1930 as 9,418,000 bbl. and the average monthly production as 784,833 bbl. The same two items for 1931 are estimated at 9,853,976 and 821,165 bbl., respectively.

Jan 1, 1932

By F. F. Aplan

Pollution control will be of utmost importance in the 1970's. In this area, the mineral process engineer has a special competence to understand and remedy many pollution situations. There is an old adage that goes, "Build a better mouse- trap and the world will beat a path to your door." Would that it were so, but the reality of the situation is such that, just as a supplier must sell his machine, a professional man must sell his competence. It is a sad but true fact that mineral processing engineers have not done a very good job in selling their extensive competence in the control of a broad range of pollution problems. Recently one of our students visited a paper pulp mill where he was shown a foam fractionator used to remove paper pulp fibers from plant discharge waters. "Foam fractionator hell, that's a flotation cell!'' was his comment. Ah so, it would appear that large numbers of technical people consider themselves experts on "foam fractionation" Or is it that we have been very remiss in demonstrating the usefulness of our equipment and processes and our professional competence to solve, these pollution problems?

Jan 1, 1970

By Bayard Morrow

THE copper-bearing ores concentrated at the Anaconda plant of the Anaconda Copper Mining Co. are principally a mixture of copper and iron sulfides associated in a gangue consisting of quartz, lightly altered granite and feldspars, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. The predominant sulfide is pyrite. The copper minerals present are: chalcocite, bornite (Erubescite), enargite, chalcopyrite, covellite, tetrahedrite and some tennantite. Normal concentrator practice removes a slime prior to ball-mill grinding. The deslimed ore is ground to approximately 10 per cent plus 65 mesh for flotation. Two selective flotation circuits are used, one for deslimed ore and one for slime. The metallurgical results obtained are shown in Table 1.

Jan 1, 1933

By Toyohiko Hirota, Fukuo Itoh

Oil and natural gas aside, sea floor mineral resources currently being exploited in Japan are offshore sand and gravel and deep-sea manganese nodules. The mining of sand and gravel has already started. With regard to manganese nodules, the geophysical investigation and the study of the mining method are also underway. This report outlines the activity of a few Japanese firms, the Deep Ocean Minerals Association formed by some 30 private firms, Government agencies, a public corporation and two government research institutes. Researches on new exploration instruments, properties of deep-sea sediments and the mining method currently conducted by the National Research Institute for Pollution and Resources are described in detail.

Jan 1, 1976

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

Underground Transitmen.-Two transitmen with experience in shaft mines; need not be full grown engineers but entirely capable of doing accurate instrument work. Location Middle West coal mines. R-419. Draftsman.-Kentucky. $150 per month.. Extensive experience in map work and construction work, such as is found in and about coal-mining operations. Send sample f work and state whether or not married. R-606. Mine Transitman.-Kentucky. $140 per month. Considerable experience in and about coal mines; must also be a fair draftsman. Send sample of work and state whether or not married. R-607. Draftsman.-West Virginia. Experience on mine 'mapping and construction work, for position with coal and coke company. R-609. Civil Engineer.-China. Salary depends upon man. Technical education and training in general engineering and building construction. Man about 30 .years of age desired, preferably unmarried. The various engineering construction in which this firm is engaged are as follows: Investigations, inspections, reports and valuations, design and supervising of construction for industrial plants and bldgs., power plants, difficult foundations, bridges and steel structures, wharf and deck construction, river and harbor works, investigating and development

Jan 6, 1919