Search Documents

By Kendall F. Born

Production of crude oil in Tennessee during 1939 was slightly more than 51,000 bbl., an increase of about 10,000 bbl. over 1938. The product,ion by counties and by fields is shown in Table 1. The increased production has rcsulted from continued activity in the Upper Cumberland district, especially in Clay County, where approximately 37,000 bbl. were marketed off the lease. This figure includes a single well in the old Tinsleys Bottom pool on the Clay-Jackson County line, although the well is in Jackson County. The "Mississippi lime" produced 10,811 bbl. in Scott and Morgan Counties, a decrease of 2568 bbl. from the 1938 production. Production during the year from some half-dozen scattered wells in eastern Clay, Pickctt, and Fentress Counties, on which there are no accurate figures, is estimated at 1000 barrels.

Jan 1, 1940

By Ch. J. Raub

A review will be given on the electrodeposition of Au, Ag and Pd and their technically important alloys focusing on recent work at the Forschungsinstitut. Special emphasis will be given to the influence of impurities on the behaviour of the electrolyte and the properties of the deposits, e.g. on resistance and on thermal and mechanical behaviour. The importance of C in gold and silver deposits and of H2 in Pd and its alloys at normal and high speed deposition rates will be discussed. Among Pd alloys attention will be focused on the Pd-Ni and Pd-Ni-Co systems. Comments will be made on deposition of Rh and Pt.

Jan 1, 1984

By W. H. Nielson, L. S. Diaz

Several techniques are presented to adjust small errors inherent in data collected from material balance measurements on the flotation process. The basic technique used is a Lagrange multiplier adjustment of the filtered data taken from the equipment measurements. The raw data are adjusted such that material balances are closed. The adjustments to each data point is inversely proportional to the square of the standard error of measurement. Problem areas in equipment utilization are discussed. Typical results from on-line measurements are presented. This technique can be applied to either on-line process measurements or metallurgical test data.

Jan 1, 1973

Herbert Moore Harbach was born in Lebanon, Pa., Apr. 4, 1891, graduated from the Lebanon High School in 1911, and entered State College, from which he received his degree of Bachelor of Science in Metallurgical Engineering in 1915. He was employed by the Lackawanna Iron Co., at Buffalo, N. Y., and was later transferred 'to their Lebanon plant to start up the newly erected benzol plant. He was later made foreman of the coke ovens, which position he held after it was bought by the Bethlehem Steel Co., and until he enlisted in the service of his country in September, 1917. He was stationed at Camp Meade, Md., until the spring of 1918, when he was transferred to the C. W. S., at Niagara Falls, as an expert chemist. There he was engaged in perfecting the various kinds of gases,

Jan 2, 1919

By N. A. Ziegler

A certain amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautmanl published a paper in which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table I. Each alloy was forged in the ordinary way to All carbon determinations were performed by " Yensen " method. [N. A. Ziegler: Recent Developments in Analysis of Carbon in Iron and Iron Alloys. Trans. Amer. Electrochem. Soc. (1929) 56, 231.1

Jan 1, 1932

By T. O. Meyer, J. R. McVey

A 10-channel automatic data acquisition system has been assembled for underground use with the Bureau's "Tunnel Stress Relaxation Gage". The automated system was needed to improve data collection by providing a rapid, long-term printout of measurement data in tunnel stress relaxation experiments. Special unit assembling and packaging of all measurement equipment, to be used in typically hostile mine environments, is the subject of this report. Even though automatic data acquisition systems have been in use for years, none have been developed with the accuracy herein described for use in such an environment. The object of this report is to inform researchers of a workable, proven, dependable underground data acquisition system. We have found that giving attention to these packaging details many times spells the differences between success and failure of underground tests.

Jan 8, 1973

By R. A. McClelland

In the development of the Sirosmelt tin smelting process the need has arisen to understand and predict the problems likely to be encountered in optimal furnace operation on larger scales and over wide ranges of operating parameters. To study these parameters in detail with existing pilot plants and production scale plants is prohibitive in terms of cost, time and limitations of furnace design. The Sirosmelt computer model, SMELT, has been developed to simulate the process and to study a range of metallurgical parameters. The model's robust basic form has allowed adaption to a variety of needs. It is now being used to generate data on optimum operating conditions for a commercial scale plant and for operator training.

Jan 1, 1984

Jan 1, 1887

By Clifton W. Livingston

So many factors influence blasting results that theories and rules are usually dismissed as impractical; the practice prevailing today is arrived at by cut and try. Usually the first step is to experiment with drillhole patterns and spacing until an arrangement is found that gives best results. The next step is to experiment with different types of explosives and sequences of blasting until the most satisfactory degree of fragmentation is achieved and until no further reduction in cost is immediately apparent. Improved fragmentation is generally attributed to the type of powder used, the sequence in which the holes are blasted, or the use of millisecond delays. Various types of drill rounds have been evolved in tunneling operations, underground development headings, and stoping, and various patterns of blasting in open pit mines and quarries. These practices usually are carried from mine to mine or from district to district, and great skill is exercised by those experienced in the art of blasting.

Jan 1, 1960

By N. S. Parate

Detailed analysis is given of the influence of water on the strength of limestone. The mechanism involved in strength reduction is described. Such analysis is of importance in geological, civil, constructional, mining, and metallurgical engineering and is closely associated with the rock mechanics involved in these areas. Mine dumping, slope stability, excavations, sedimentation, etc., are very much affected by the presence of water. Tensile stresses, which have an important role in the development and propagation of fissures, are produced by water in cracks. The development of fissures can be responsible over a long period of time for an ultimate, catastrophic failure.

Jan 1, 1974

By M. P. Nackowski, Armond H. Beers, W. T. Parry

Three hundred soil samples were collected on a one-mile grid in a 400-square mile area of the Oquirrh Mountains, Utah, including the Bingham-Lark, Ophir, Rush Valley, and Mercur mining districts. The soil samples were analyzed for copper, lead, zinc, silver, molybdenum, manganese, and iron by X-ray fluorescence using arsenic as an internal standard. Anomalies coincide in most cases with the mining districts. However, in the Mercur district no anomalies were detected. Also samples collected one mile from the Bingham mine barely reflect this major producer. No samples were collected within the Bingham mine area.

Jan 1, 1973

By Burt A. Waite

The new OSM regulations for ground water monitoring of underground coal mines have been the source of many concerns for the mining industry. Because the regulations were initially written at the federal level, but are being administered at the state level, considerable confusion still exists within the industry as to what is really required. Based on submission and/or approval of more than 30 monitoring plans for existing mines in Pennsylvania, West Virginia, and Ohio, three basic sections are necessary. They are: 1. background data on the hydrogeologic setting of the mine, 2. the monitoring plan itself, and 3. mining procedures to minimize adverse effects on ground water. Like all of the OSM requirements, ground water monitoring will be a new burden the coal industry must bear, but with proper planning and communication with the regulatory authorities it need not be as bad as originally feared.

Jan 1, 1983

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By R. B. Strathmore Cooke, Eugene L. Talbot

The perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds. Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydro-carbons. The large contact angles probably result from the terminal –CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride. From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others.

Nov 1, 1955

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939

By O. Knacke, H. Barth, W. Gans

The rate of cementation was determined by measuring the time required to consume a thin electrodeposited layer of the cementating metal as indicated by a sudden increase in the electrical potential. The diffusion controlled cathodic current of the more positive metal was measured by conventional electrochemical techniques and compared with the cementation rate under the same experimental conditions. Micrographs revealed different types of crystal growth in different surroundings e.g. dendritic growth in acidic solutions.

Jan 1, 1973

By J. L. Wright

When management is confronted with the risk of constructing a waste disposal well, these are some of the questions which may arise. Should the company expand the present waste treatment plant? More lagoons will cut into valuable acreage which might be needed later, and yet the pollution engineer says he can guarantee results. On the other hand, does the formation being used for those successful disposal wells off to the west extend over far enough to be used for the company's own well? Will the formation be thick enough? Will it be too deep? Will it be porous and permeable enough? Apart from needing to make a profit on the products made at the plant, plant officials must sometimes act under pressure to comply with pollution standards. The manager must build the cost of the pollution control system into the price of the products made by the company.

Jan 1, 1970

By C. C. Bailey

THE vendor seeking outside capital for his project has the following potential sources which may be approached; 1--private sources, 2-institutional funds, 3--government agencies, 4--established mining concerns, and 5-public financing.

Jan 7, 1953

By Ove Rehnberg

Catalytic purifiers are widely used as exhaust treatment devices on diesel equipment in confined spaces. The paper summarizes some studies carried out at the University of Lulea on diesel exhaust purifiers. The main purpose has been to elucidate important chemical activities of catalysts useful for the improvement of their effect. The effects of platinum catalysts on exhaust constituents such as carbon monoxide, nitrogen oxides, unburned gaseous hydrocarbons, and polynuclear aromatic hydrocarbons are discussed. Also pointed out are the great differences in catalyst activity and advantages/disadvantages associated with the catalysts.

Jan 1, 1982

Stuart Manwaring Buck, a member of the Institute from the first year of its existence, and one of its Managers from 1883 to 1885, died at his home in Bramwell, West Va., on July 16, 1921, at the age of 79 years. He was the son of David and Matilda S. Ruck of Boston, and was educated at Williams College, at the Massachusetts Institute of Technology and at the School of Mines at Freiberg, Germany. Mr. Buck was one of the pioneers in the development of the coal fields of West Virginia. From 1872 to 1877 he was connected with the Kana-wha and Ohio Coal Co. as engineer and as lessor; from 1877 to 1888 he was general manager of the East Bank Coal and Coke Co.; from 1888

Jan 1, 1922