Search Documents

By Oren C. Baptist, Eliot J. White

Samples of four reservoir sands having different degrees of water sensitivity were subjected to several laboratory tests to determine differences in capillary behavior attributable to clay-mineral effects. The degree of water sensitivity was estimated by the difference between gas and water permeability. Unsaturated pore volumes determined with mercury injection were comparable to irreducible water saturations determined with the semipermeable bar-rier method only for the non-sensitive sands that contained small amounts of non-swelling clay minerals. Irreducible saturations were independent of salinity of the water, which suggests that most residual water is adsorbed 0.7 a film over solid surfaces and that internal retention by clay minerals is relatively insignificant. The water-sensitive sands imbibed water to higher saturations than did non-sensitive sands, and this result is believed to be a combination of the effects of clay minerals and preferential wettability; however, the relative importance of each of these effects is riot determinable. Thus it is concluded that the semipermeable barrier method is the best of the laborafory methods used for estimating formntion water .saturations in the sands studied. INTRODUCTION This investigation is a continuation of studies of the role of clay minerals in petroleum production in the Rocky Mountain area. Previous work has shown large differences in gas and water permeability in numerous reservoir sands; these water-sensitivity effects observed in the laboratory have been correlated with well behavior in the field, and the degree of water sensitivity imparted to reservoirs by the various clay minerals has been determined.'.' The effect of interstitial clay minerals on formation water3 saturations is not so well known. It has been reported that formation water saturations probably are higher in clayey than clean sands,' but this effect has not been evaluated in the laboratory, and the relative effect of the various types of clay minerals on formation water saturation has not been determined. The clay-mineral groups of most importance to this study and to petroleum production in general are kaolinite, illite, and montmorillonite. The minute layers of montmorillonite are loosely bound to one another so that water enters between them, causing great expansion of the particles. Kaolinite and illite do not exhibit interlayer hydration, but they do immobilize considerable amounts of water owing to their large surface areas, which are of the order of 15 to 97 m2/gm of clay.5 The four Wyoming sands used in this study were selected to represent a wide range of water sensitivities. These sands, with the number of wells and fields from which the samples were obtained, are: Second Frontier, five wells in two fields; Newcastle, six wells in one field; Tensleep, two wells in two fields; and Lower Muddy, five wells in one field. EXPERIMENTAL METHODS AND PROCEDURES Water-displacement data were obtained by the semipermeable barrier method," using both fresh water and brines having either 16,500 ppm sodium chloride or calcium chloride. A displacement pressure of 35 psi was found to be sufficient to obtain the practical irreducible water or brine saturation (IWS, IBS) in most samples. Mercury-injection data were ob-tained with equipment and pro-cedures similar to those described by Purcell.7 Exceedingly high pressures are required to attain complete mercury saturation by this method; however, since saturations in most samples change very little with large pressure increases above 1,000 psia, the maximum pressure used was 1,400 psia. To facilitate comparison of mercury-injection and water-displacement results, it is convenient to express mercury-injection data in terms of unsaturated pore volume. The abbreviation, (100 - SHg)min, is used to denote the pore volume unsaturated by mercury at 1,400 psia injection pressure. Gas permeabilities, ki, were deter-mined by the method proposed by Klinkenberg.8 Methods of determining types and amounts of clay minerals by X-ray diffraction analyses, as well as methods of determining water permeability, have been described previously.' The imbibition characteristics of

Jan 1, 1958

By D. M. Warner, Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as 8and-cast and as heal-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brine11 and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. The demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.' Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergran-ular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about 950" F., quenching in oil or in cold or boiling water, and artificially aging

Jan 1, 1926

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chryso-tile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings. Four of the more important factors that have influenced recent developments are: 1. The lack of discovering and developing new deposits of any important size to supply the increased demand. 2. Rapid postwar expansion of industrial uses, especially in asbestos cement products, together with in-rreased manufacturing facilities. Euro-peal) countries are again back on the market with their demand. 3. The ability of manufacturers to develop their technique of blending fibers and obtaining more utility value out of each ton of fiber, together with the utilization of shorter grades of fiber to obtain equally as good products. In the past, many manufacturers were wasteful in their use of fibers. 4. The struggle for reduced operating costs, in face of increased wages and prices of supplies, together with the necessity, at some mines, to change the method of mining from open quarry to underground. Most of the recent capital invested in the asbestos mining industry has gone into more efficient extraction of the fibers from the existing ore, especially in the recovery of the shorter grades. There has been very little new plant expansion. Progress in the utilization of shorter fibers has been so far reaching that some of the mining companies are retreating present tailings as they leave the mill, and others are considering retreating of the old tailing dumps for recovery of fibers that, until recently, were not saleable and were discarded as part of the tailing. Many of these dumps contain much valuable fiber from days when milling was very inefficient. It might be appropriate to mention here that the present known asbestos reserves of proved commercial value (excluding Russia) are being depleted at an alarmingly rapid rate, about 10,000,000 tons of ore is being mined annually. No new deposits have come into production during the last 15 years, with the exception of certain deposits in Africa, which are the most promising, and minor developments in Canada, Venezuela, Cyprus, Australia, and Brazil. The African deposits are the only ones that hold promise of developing large reserves. Unless new deposits are developed, in twenty years or maybe sooner, the supply picture will not be a very bright one. Stimulated by the acute shortage, increasing fiber prices and technical developments, many new areas are being prospected in Canada, United States, New Zealand, Newfoundland, South America, Europe, Africa, and China. From information now available, it appears that no real progress has been made in duplicating this rare development of nature by producing synthetic asbestos. The most promising experiments were carried out at the University of Leipzig, but they seem far from practical. There has been marked progress in fiber glass manufacture, but so far, it has replaced asbestos only in very few instances for minor uses. Asbestos ore and the fiber it yields are different in some respect at each mine and vary usually in the following: 1. Percentage of fiber content by weight to the gangue. 2. Variations in proportions of long and short fibers, some deposits being predominantly long fiber and others short fiber. 3. The hardness of the rock in which the fiber occurs. 4. The nature of the fiber, as to

Jan 1, 1950

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5'798'14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By Ihor A. Kunasz

Introduction Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. With the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, are presently exploited by Foote Mineral Co. The brines of the Great Salt Lake of Utah, the Smackover formation, and the Imperial Valley geothermal field, have been defined as important resources of lithium. In South America, new occurrences have been identified in Bolivia and Argentina. At the Salar de Atacama, Chile, new production capacity is scheduled for 1984. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded, reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938, an ionic radius of 0.68Å and a charge of +1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO) / Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns, 1955). Genetically, the pegmatites are associated with neighboring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, et al. (1949), a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their re-

Jan 1, 1983

By J. M. Karpinski, R. O. Tervo

A method and equipment have been developed for measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts. The results are interpreted in terms of the flaw theory of brittle fracture. The view is now widely held that brittle materials comprise a strong matrix, throughout which flaws or points of weakness are scattered at random. Failure always starts at one or more of these imperfections, and planes of fracture are established by the geometry of the flaw distribution. This view has been developed extensively by Weibull 1,2 and experiments of a confirmatory nature have been reported.3,4 Thus the process of fracture or size reduction of brittle materials can be regarded as a process of elimination or creation of flaws, and the concept of strength is intimately connected with the size and history of the specimen tested. One consequence of the point of view described above is that brittle materials will fracture to yield similar size distributions, although the impact energy to produce a given amount of fracture may vary greatly from one material to another. Generally speaking, experimental investigations of brittle fracture in solids have been confined to two extreme experimental situations. On one hand, we have tests on single specimens of well-defined, but artificial, geometry and, on the other, empirical data have been obtained on the feed-product relation in a variety of mills. The first situation necessitates specimen preparation, which in the case of brittle materials is equivalent to a priori size reduction, while the second one suffers from the disadvantage that little knowledge is gained about individual fracture events. Also, the statistical significance of single specimen tests may be questioned. Our approach lies somewhere between these two extremes. We test a large population of sized specimens and yet subject each specimen to a single fracture event. In 1956 G.H. Fetterley of Norton Co., Chippawa, Ont., made the empirical observation that product size distributions obtained from impacting sized grits can be described by the following equation where R is the proportion by weight of the grain that remains on a screen having an opening x on a side, x, is a parameter having the dimensions of length, and r is a number. This equation has since been derived on a theoretical basis by Gaudin and Meloy.5 They identify x, with the initial size of the test piece and r with the number of flaws per unit length. As will be shown below, our experiments indicate that both x, and r are functions of energy and hence they should more properly be called the effective initial size and the effective number of flaws respectively. Also, our empirical data give us no basis for assuming that r represents the effective number of flaws per unit length, rather than per unit volume. METHOD AND MATERIALS The impact test machine has been designed to feed specimens, essentially one at a time, into an evacuated chamber, where they fall freely and are struck with random orientation by one or the other of a pair of flat steel vanes. The vanes are mounted at opposite ends of a steel bar, which rotates at a closely controlled angular velocity about a vertical axis. Fig. 1 shows the flat circular vacuum chamber with the cover removed, and the horizontal steel bar with the steel vanes at the ends. The cylindrical pot in which the grains are collected after impact appears at the left. Fig. 2 shows the equipment assembled for a test. The vacuum chamber occupies the central position with the variable speed drive below the table surface, the vacuum pump at the extreme left

Jan 1, 1964

By U. Andres

U. Andres (The Technion, Haifa, Israel)-The authors are to be congratulated on their research, new and interesting, in a field which, however, the present writer and his assistants have been trying since 1962 to bring to the attention of the scientific and technical world, by means of publications covering several different aspects of this many-sided problem. We announced, in these publications, the results of magneto-hydrostatic (MHD) separation of magnetic and nonmagnetic minerals which we made in magnetic fluids (in paramagnetic solutions and suspensions of magnetic particles) which interact with permanent" and impermanent" inhomogeneous magnetic fields. There is no doubt that the authors have succeeded in creating ferrimagnetic colloids made by dispergation of 10-30 wt % of magnetite in kerosene in the presence of 7-10 vl % oleic acid. It may be judged by [Figs. 3 and 4] that the suspensions represent great stability systems and also "hysteresisless" fluids [(Fig. 5)] which bear witness to the existence of superparamagnetic suspensions. If the viscosity of these colloids is not so high, and the cost of preparing them can be covered, the fluids which have here been received can possibly be of interest to the technology of mineral separation. The potential possibility and technological perspective of similar media is demonstrated in our joint work with G. Bunin18 in 1965. The research carried out on the pushing out of cylinders and spheres from magnetic fluid is impressive; it would, however, have been interesting if the authors had compared their results with those on the pushing out of bodies from magnetic fluids adduced from our work." In my books" there happens to be described an experiment on the pushing out of a sphere in magnetic wedge field, in which the pushing out force of suspension with 5 vl % of magnetite reached 125 g per cc. This testifies to interesting possibilities of these media. Our works' shows also, on the basis of Laplace's equation the receiving of an interesting distribution of pushing out forces by selection of corresponding configurations of magnetic poles. Objection must be made to the authors' introduction of the term "antigravity force." The direction of this force does not depend on the direction of the gravity force and their opposition, i.e., antigravity is only one particular case. I am in full agreement with the authors' statement that magnetic pushing out forces "can be utilized to separate nonmagnetic objects according to variations in their densities." It is, however, necessary to make only one important addition, which can be found in our research on MHS at the Technion in Haifa, namely, that magnetic fluids in magnetic fields can be utilized in the separation of minerals according to variations in their magnetic susceptibility. The authors' conclusion is especially important considering the fact that in our publications" (including one in English") some designs of MHS separators and some technological results received on MHS-separators have already been described. S. E. Khalafalla and G. W. Reimers (Authors' Reply)We were aware (mostly through Chemical Abstracts of the American Chemical Society) of the use of solutions of paramagnetic salts such as manganous sulfate in agnetohydrodynamic separations by the Russian school headed by G. Bunin."n Professor Andres' contributions to this school are also evident in his application of the ponderomotive forces in an electrolyte placed in electric and magnetic cross-fields to separate coal and other useful minerals." It must be realized, however, that the foregoing research by Bunin et al." involved the use of magnetic fields and field gradients of very large magnitudes, i.e., such that H • grad H - 101 Oe2 per cm. The magnetization of paramagnetic salt solutions range from 0.1 to 0.5 gauss (at fields of a few thousand Oersteds) and never reach saturation. The magnetization of our superparamagnetic ferrofluids ranges from 100 to 500 gauss and reach saturation at fields of a few hundred Oersteds. Hence, to effect the same separation, the quantity "H

Jan 1, 1974

By W. E. Remmers

The fact that gray iron increases in volume, cracks and distorts upon repeated heating and cooling is rather conlmon knowledge. In ingot molds, Diesel engine pistons, carburizing boxes, continuous furnace parts, grate bars, stoker parts, and all castings that are subjected repeatedly to high and low temperatures, the phenomenon of growth presents a vital problem. Ingot molds distort and produce cracks which result in seams or laps and later appear as defects in the finished product. The heads of Diesel pistons frequently fail by cracking in a stellar shape. This is attributed usually to the result of permanent growth. Distortion and change of dimension of furnace parts frequently renders them entirely unusable. In chain grate stokers, mechanical difficulties frequently are caused by the growth of the links. In proper operation these links should never attain a temperature sufficiently high to start growth; nevertheless, some have grown in. on an 8-in. length when improperly operated. Even though the phenomenon is generally known there still exists a deficiency in the explanation of the mechanism of this growth. The field of investigators of this subject has a decided variation in opinion concerning the causes. The problem is of sufficient importance therefore to warrant further consideration. Review of Published Work Since the published work, particularly the European, contains much detail, only the outstanding results and conclusions of the investigators will be reviewed. The pioneering investigations of Outerbridge in 1904 and 1905 brought forth the conclusion that growth was not a function of chemical or crystallographic changes but was a result of the formation of fine hair cracks. These cracks are supposedly due to a nonuniformity of thermal expansion and contraction which ruptures the structure of the material. More recently Benedicks and Lofquist presented a purely mechanical theory, which is similar to that of Outerbridge. These investigators believe the temperature gradient from the outside to the center of the cast piece causes a contraction of the outer layers on passing

Jan 1, 1931

By F. W. Jessen, R. W. Durie

The dissolution of salt in the development of salt cavities is controlled by free-convection boundary layer flow along the salt surfaces. It is the purpose of this paper to expand upon results published previously, and primarily to illustrate the influence of surface features on the boundary layer and hence the dissolution process in the development of underground salt cavities. General dissolution equations are presented that apply to a surface inclined to the vertical. A salt surface inclined so as to be overlain by water is dissolved by boundary layer flow, while an inverted surface is dissolved by a combination of boundary layer and cellular flow. Detailed investigation of the boundary layer was limited to laminar free-convection flow. Truly laminar free-convection boundary layer flow may be encountered only in laboratory solution cavities, but the boundary layer will control dissolution even where cavity dimensions are such that free-convection turbulence will occur. The factors found to significantly affect the laminar boundary layer will affect dissolution with a turbulent boundary layer. INTRODUCTION Underground salt cavities have been used extensively for the storage of LPG products, and the use of these cavities is expanding each year. The increasing requirements for such cavities suggest the need for a better understanding of the mechanisms involved, for the purpose of the control of cavity geometry and the most effective use of the injected water. A previous paper outlined a quantitative approach to the determination of salt dissolution rates in the laminar free-convection dissolution of salt. It is the purpose of this paper to expand upon the results previously published and to point out significant factors in the application of these results to the dissolution of field cavities. The dissolution of salt in laboratory scale cavities is controlled by the free-convection boundary layer, which is the region of flow along the salt surface caused by the difference in buoyancy forces resulting from the salt dissolution. The transfer of salt into solution at the salt face causes an increase in salinity, and hence a greater density, in the water at the salt surface. The region of higher density tends to fall through the lighter, less saline water and a flowing boundary layer is the result. The water remains stationary at the contact with the salt surface,l so the resulting velocity profile is such that the influence of gravity is opposed by a viscous shear force at the salt surface. For salt to be transferred into solution from a solid surface to a boundary layer of fluid, it must diffuse through a stationary film of water at the salt contact. According to Fick's first law, the rate of mass transfer by diffusion is the product of the diffusion coefficient and the concentration gradient, with diffusion transfer in the direction of decreasing salinity. Once the salt has passed into the boundary layer, it will be transferred by a combination of molecular diffusion and convection. The convection transfer will in turn affect the rate of dissolution by influencing the gradient of the salt concentration at the surface. In the previous investigation by the authors to determine the basic mechanism of the salt dissolution process, an equation was developed that agreed very well with the experimental rates of free-convection salt dissolution from a smooth vertical surface. The technique was taken from the work of Eckert2 in the analogous heat transfer system and will be referred to as the integral method. The rate of salt transfer from a vertical section of height H was found to be:

Jan 1, 1965

By R. D. Carpenter, R. R. Smith, E. E. Sougstad

The Union Carbide Nuclear Co., in treating low-grade tungsten and molybdenum-copper ores at the Pine Creek mill near Bishop, Calif., employs flotation for the initial extraction of the valuable mineral constituents. These minerals consist of scheelite, molybdenite, and several of the copper sulfides including chalcopyrite, bornite, and possibly chalcocite. They occur in a gangue consisting mainly of quartz, pyroxene, and garnet, with minor amounts of calcite and fluorite. This assemblage of minerals presents an unusual grinding problem because of their diverse physical characteristics. Feed for the circuit is prepared from -6-in. ore by screening on a rod deck screen to remove the -5/8 - in. material. The+5/8-in. fraction is crushed in open circuit with a 5 1/2-ft Symons shorthead crusher operated at a closed- side setting of approximately 3/8 in. The screen undersize and the conecrusher discharge are then combined to constitute the feed to the grinding circuit. The ore is ground in 6 by 5-ft grate discharge ball mills operated in closed circuit with 54-in. spiral classifiers. The classifier overflow goes directly to the flotation section of the plant. Studies of the flotation circuits have shown that the maximum recovery of the tungsten, molybdenum, and copper minerals occurs in the particle-sue range from 100 mesh to approximately 400 mesh. Further, practice has shown that the ore minerals are effectively reduced to this size range if the total ore is ground to -48 mesh. The general objective of the grinding circuit then is to reduce the feed to -48 mesh with the production of a minimum amount of slimes. The purpose of this investigation was to ascertain how well the grinding circuit was carrying out this objective. The method used was to sample the various products in the grinding section, size these products accurately, and analyze the resulting sue distributions. SAMPLE PREPARATION AND SIZING TECHNIQUES Representative samples of the different grinding circuit products, namely, new feed to the ball mill, ball mill discharge, classifier overflow, and classifier return, were taken over a 24-hr period. The samples were then dried without being filtered to avoid loss of slimes. The percentages of solids in the different products were the following: new ball-mill feed, 95%; ball mill discharge, 82%; classifier overflow, 52%; and classifier return, 84% solids. Particle sizes were determined on each product by wet-screening an

Jan 1, 1962

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

By Leendert de Witte, Fred J. Radd

In many areas caring failures can be directly related to electrical currents observed in the casings. It is the thesis of this paper that the observed casing currents are mainly due to electrochemical potentials of the type in evidence on spontaneous potential curves of electrical logs. The general nature of these potentials are discussed and an equivalent circuit is given for current and potential distributions around open holes. The casing forms a short circuit to these potentials and tends to average the effects of local cells. The case of casing corrosion opposite the Dakota water sands in the salt-mud area of Kansas is discussed anil used us a qualitative, illustration of the relation between SP's and casing currents. A method of quantitative derivation of casing current distribution frorn electric log SP curves, using linear transform theory, is described and results are compared with a measured current profile. The effects of hydrogen over-potentials at the cathodic portions of the pipe are considered and some laboratory data are given in support of conclusions regarding the over-1.01tuge.s. INTRODUCTION To date an appreciable amount of work has been done on the measurement of oil well casing currents and on the correlation of the anodic portions of the current profiles with corrosive casing failures. Speculations on the origin of the casing currents have, however, remained rather vague; and although almost every plausible cause has been mentioned, there is to the writers' knowledge no clear-cut expose' on the details of the causes of the corrosive currents in the literature. A study of current surveys and casing failures in the N.W. Burnett field, Ellis County. Kan.. indicated the probability that concentration cell emf's between the Wellington salt section and the relatively fresh waters in the Dakota sands were a major cause of the corrosion currents. A more general concept evolved upon analysis of the severe corrosive conditions in the Pleistocene sands in the Ventura Avenue and San Miguelito fields in California. In this area no major variations in the salt content of the formation waters occur and yet large casing currents are observed. An explanation is found in the fact that the local spontaneous potentials which are set up due to concentration contrast between the drilling fluid and the connate water are short circuited when casing is set. The very conductive path through the casing increases the magnitude of the currents and has the tendency to average local sources over fairly large intervals. Current will flow between the sections that are predominently shaly and the sections that are mostly sandy. At the places where the current leaves the pipe, corrosive attack will occur. This same phenomenon will be present wherever unprotected pipe is set through sections that show large SP kicks on the electric logs over reasonably thick interval~. GENERAL- NATURE OF THE SPONTANEOUS POTENTIALS When a sequence of sedimentary rocks is penetrated by a drill hole filled with a mud which has a different salt concentration from that in the formation waters, various types of electrochemical potentials are established between the formations and different parts of the mud column. Opposite clean sand sections. a simple liquid-liquid junction potential will be observed; while opposite argillaccous formations, a membrane potential, often referred to as shale potential, will be established. The first quantitative analysis of these emf's in terms of liquid junction and membrane potentials is due to Wyllie.1

Jan 1, 1956

By James C. Ray

The age classification of the mineralized veins of the Butte district, as given by Weed and Sales, was tacitly accepted for many years. Weed, whose field work was completed in 1906, divided the copper veins into groups of four ages.' In 1913, Sales modified Weed's classification and assigned all mineralized veins (including the silver-zinc veins of the border or "peripheral" zones) to three periods of fracturing and mineralization. Both writers based their classifications mainly on the relative ages of the observable faulting whereby the veins of a so-called "earlier" system are intersected and offset by those of a "later" system. Nevertheless they possess structural and mineralogical characteristics in common which indicate that they are of the same age. The writer has maintained since 19143 that these vein systems were formed during one general period of mineralization along a network of intersecting fractures of approximately simultaneous origin and that the existing offsets are largely due to postmineral faulting. Leith,* takes cognizance of the accumulating mass of data relative to the simultaneous formation of intersecting fracture systems and says, referring to ~utte: "It now appears that the mineralization accompanying them (individual structure systems into which the veins have been grouped) is substantially of one period, indicating that the successive structural movements took place mainly within the period of mineralization." This paper presents the results of certain structural experiments which suggest a modified interpretation of the published data on the Butte district. The interpretation is substantiated by the writer's observations in the Butte mines and is offered with the hope that it will reconcile the structural with the mineralogical conditions existing in this most interesting district; also, that it will emphasize the importance of a

Jan 1, 1931

By N. E. Rogen, N. J. Grant

WHILE direct measurements of the growth of precipitate particles during aging is of fundamental value, few such measurements have been made. Direct measurements by means of optical or electron-microscopy and X-ray techniques are preferred, however, many of the aging studies have been based on indirect methods such as electrical resistivity and hardness. Because of the minute size of most precipitate particles (less than 1000A) the light microscope is of limited use while electron microscopy is subject to slowness, etching problems and consequent resolution problems. It is fortunate that alloys of the Nimonic type, based on Ni-Cr-Ti-Al, lend themselves to accurate and relatively easy particle size measurements. With proper balance of titanium and aluminum, the only aging precipitate is the gamma prime (r') Ni3,(Al, Ti)2 phase and this phase is the basis of the high-temperature strength of these allos.3-6 The Ni3(Al, Ti) phase is a face-centered-cubic, ordered structure with nickel atoms occupying the cube faces. Titanium atoms can replace three out of every five aluminum atoms and when substituting do so preferentially.2 Electron microscopy has shown that during aging of most of the commercial alloys of this type, precipitate particles are unusually uniform in size and distribution, and that the volume of (r') phase is large (20 pct).4,7 The aim of this investigation was to measure the growth of (y') phase during aging. In so doing, it was hoped that a clearer understanding of the aging process would be attained. X-ray line broadening was used as the measure of precipitate particle size. This technique was selected because it can measure and average the diameter of thousands of particles in one operation. The variations in hardness and matrix lattice parameter with aging were also studied and related to the particle size. EXPERIMENTAL PROCEDURE An alloy of the following composition was studied: Cr Ti A1 C Ni Wt pct 20.71 2.98 1.43 0.04 bal. At. pct 22.06 3.47 2.95 0.18 bal. The alloy, a 15- lb vacuum melt, was forged to 1/2-in. diam at a temperature of 1900" to 2200°F; was solution heat treated for 4 hr at 2000°F and water quenched; and was then aged in various ways. The ASTM grain size was 4 to 5. No (7') phase could be detected by X-ray analysis after solution treatment and electrolytic extraction. Aging was performed on 2-in. long specimens at 1400°, 1500°, and 1600°F for increasing times. One-half inch sections were removed after each time increment and were then electropolished in a solution of H3P04 saturated with chromium trioxide at a potential of 30 v and rectified with a tantalum electrode. Rockwell hardness measurements were taken using one side of the polished specimen. Matrix lattice parameter determinations were made on the other side using filtered chromium radiation references with the position of the (220) line of a silicon standard. To enable the precipitate particles of the (y') phase to be measured using X-ray line broadening techniques, it is first necessary to separate and concentrate this phase by electrolytic extraction. Extraction is necessary because the difference between matrix and precipitate lattice parameters is only approximately 0.5 pct and intensities of.the (y') phase lines are very weak relative to those of the matrix. The extraction techniques employed have been described before and found to produce a reasonably quantitative separation.398 A water solution of 15 pct H3Po4 is used at a current density of 0.5 amp per sq in. at 6 v. The precipitate particles are separated from the liquor by centrifuging and decanting and are then washed, dried and repowdered. A plot of the X-ray intensity vs diffraction angle for the (111) line of the precipitate particles was used as a measure of particle size. The intensity curve approximated the shape of Gaussian distribution function and its breadth was measured at the half height. The (220) line of a silicon standard was used to correct the measured line breadth for instrumental and other broadening errors. The Scherrer formula was used to calculate particle

Jan 1, 1961

By H. R. Brannon, R. J. Robinson, G. W. Kattawar

Accurate prediction of storm wave characteristics are needed for design of offshore structures. Statistical methods of random noise analysis provide techniques for predicting required wave properties. These techniques have been used to analyze and characterize storm wave profiles from Gulf of Mexico recording installations in 34, 65 and .98 ft of water. Correlations based on the results can be used to predict wave crest probabilities and wave shapes for a range of Gulf water depths and storm conditions. Example predictions of wave crest probability as a function of water depth for a particular set of storm conditions are given. INTRODUCTION Accurate predictions of wave crests and wave shapes are needed for design of offshore structures. With predictions of wave crests, platform deck elevations giving adequate protection from exposure to storm waves can be selected. Use of hydro-dynamic wave theories with the wave crest and wave shape predictions permits an estimate of the wave forces an offshore structure must withstand. Observation of ocean waves suggests use of statistical analysis for studying wave characteristics for water depths beyond the breaking wave zone; recent wave generation theories lend support to this approach. l-3 One of the most powerful methods of statistically analyzing wave profiles was introduced by Cartwright and Longuet-Higgins; most of the basic relations used were developed by Rice5.6 in studies of random noise theory. This method predicts wave crest elevation probabilities from two parameters characterizing a wave profile. The statistical approach also provides a means for predicting wave shapes. In the random noise model of a wave profile, surface elevation is represented as an infinite sum of sine waves with closely spaced frequencies and random phase angles. Power density is proportional to the sum of the squares of the amplitudes of sine waves having frequencies within a narrow band, and the distribution of power density as a function of frequency is called the power density spectrum, or power spectrum. The power spectrum characterizes an irregular sea, and hence finds use in motion studies of ships, barges and semisubmersible drilling platforms. From the power spectrum, a wave profile of any duration of time can, in principle, be calculated; this long wave profile depicts the many wave shapes to which a structure may be exposed. Thus, the statistical methods of wave analysis provide an approach to selecting wave shapes as well as wave crest elevations needed for design of offshore structures. For practical application of these techniques, power spectra and related quantities must be predicted from storm properties. Barber and Tucker 7 have reviewed correlations of wave properties and storm conditions. Their review summarizes work of Darbyshire,8 among others, in which a correlation of power spectra with wind intensity of the North Atlantic was developed. These results, plus more recent work by Pierson and Moskowitz and Kitaigorodskii,10 establish feasibility of correlation, but there is no theoretical basis for modifications extending the relations to other areas as remote as the Gulf of Mexico. Hence, to predict characteristics of Gulf of Mexico waves, a study of local observations is needed. This paper presents (1) a practical approach to computing wave profiles hat depict shapes of waves for use in force calculations, (2) a summary of relations for predicting probabilities of wave crest elevations, (3) correlations of parameters needed to apply these methods in the Gulf of Mexico and (4) examples of application of the techniques. THEORETICAL BACKGROUND The following sections summarize relations needed to calculate wave profiles and to estimate wave crest probabilities. These relations also identify quantities that must be related to storm

By J. E. Papin

MORENCI ores contain as an average about 0.015 pct molybdenite, MoS2. Incidental to the concentrating operations applied for the recovery of copper minerals, approximately two-thirds of the molybdenite is floated and appears in the final copper concentrate. The economic importance of molybdenum and the success achieved in its recovery in milling operations elsewhere encouraged research directed toward its recovery in marketable form. Several procedures are utilized to effect separation of molybdenite from copper and iron sulphides, but only two have wide application. In the better known of these two methods the molybdenite in the copper concentrate is depressed in a flotation operation using soluble starch as the depressant. The tailing from this treatment thus becomes a low-grade molybdenite concentrate which after thickening, filtering, and low temperature roasting is repulped with water and subjected to additional flotation steps for recovery of the molybdenite. A thio-phos-phate collecting agent is employed in flotation of the copper minerals. Presumably the stability and lasting effects of that collector type necessitated the practice of depressing molybdenite followed by subsequent roasting to insure elimination of copper and iron sulphides from final molybdenite concentrate. The second important method of recovery is applied at various southwestern plants. In those plants xanthates are in use as copper collecting agents. It has been found that xanthates are relatively unstable and their collecting power for sulphides is destroyed by very simple procedures. The method generally applied is to subject the xanthate-acti-vated concentrate, in the form of a pulp, to prolonged heating using steam as the heating medium. A concentrate thus treated may then be subjected to a flotation operation for recovery of the molybdenite, using mineral oil collecting agents, and the copper and iron sulphides will be depressed. Neither of the above processes was applicable to Morenci concentrates. Morenci uses a thio-phos-phate collecting agent in its flotation operation. However, it was established that soluble starch was not a depressant for Morenci molybdenite; therefore the first step in that process was not applicable. AS would be expected the copper and iron sulphides in Morenci concentrates could not be depressed by the heating methods used on xanthate activated concentrates. Low-temperature roasting did eliminate the effects of the thio-phosphate but had to be rejected as uneconomic in as much as the tonnage of concentrates involved was too great. Preliminary research having established the above facts, it became obvious that new methods would have to be developed for the recovery of molybdenite from Morenci concentrates. A broad laboratory investigation was initiated along two general lines, both directed toward depression of copper and iron sulphides. One approach was through the use of water-soluble oxidizing agents with the objective of destroying the thio-phosphate in the concentrate and thus eliminating its collector effect. The other approach involved the use of soluble sulphides, which have long been recognized as sulphide depressants. These efforts resulted in laboratory processes which showed promise. Research was then extended to a pilot plant having a daily capacity of several tons of concentrate. This operation soon demonstrated that soluble sulphide—basically sodium polysulphide—when applied to a pulp made slightly acid with sulphuric acid, proved to be the most effective sulphide depressant. The rate of concentrate treatment in this plant and the low molybdenite content of the concentrate prevented carrying the process to a conclusion, namely, production of molybdenite concentrate of marketable grade. Laboratory treatment of pilot plant concentrate indicated that a marketable product could be made from it, given a tonnage suited to available cleaner flotation machine capacity. Accordingly, the molybdenite plant was enlarged to permit treatment of the total copper concentrate from the extension plant, maximum of approximately 800 tons per day. In the enlarged plant a major difficulty was encountered. No criteria could be established as a basis for control of the process. In the early stages of flotation, because of the small amount of molybdenite involved, there was no visual evidence of the relative floatability of molybdenite with respect to

Jan 1, 1956

By C. E. Shoenfelt

There was a notable decrease in drilling operations in 1940 in all of the Rocky Mountain states except Montana, where the two large fields on the Canadian border, Cut Bank and Kevin-Sunburst, were espe-cially active. The expanding markets for Montana natural gas made necessary the more intensive development of such fields as Rowdoin, Cedar Creek and Devon. While there were no important oil and gas discoveries in 1940 in any of the Rocky Mountain states, a few small pools were opened, which may constitute separate areas but may prove with later development to be extensions of old fields. Some of the old fields were extended and deeper pay zones were discovered in others. These have given the areas greatly increased oil reserves and therefore are just as important as the discovery of new fields. The more important of the developments in 1940 are given, by states, in the following paragraphs. Colorado Hiawatha Field, Moffat County.—The Mountain Fuel Supply Co. began the development at Hiawatha of its oil reserves, which were discovered in about 1929, and late in the summer oil began moving from the field by truck to the shipping point at Rock Springs, Wyoming. The Hiawatha field of northwestern Moffat County was discovered in 1927 by the Sormir Petroleum Co., with the completion of No. r Florence Wilson for 4,5,000,000 cu. ft. of gas a day from a Wasatch sand lens at 2200 it. In later development of the field, oil showings were reported in several wells but no development of this resource was undertaken until 1940, when a test of the oil possibilities was started with the release in April of a location for No. 5-A Wilson on the S\W. SW. NW. of sec. 23-1zN-1ooW., on the east side of the field. The Well had an initial production of 327 bbl. of oil a day pumping from three Wasatch (Tertiary) sands between 2005 and 2540 ft. It was drilled to 2562 ft., where the 65/8-in. casing was cemented and gun-perforated at 2005 to 2125 ft., 2260 to 2335 ft. and 2513 to 2540 ft. At the end of the year, this well was averaging zoo bbl. of oil per day, pumping. Two other wells were drilled for oil on Hiawatha during the summer—one a small well of 60 bbl. per day and the other a small gas well. Powder Wash Field, Moffat County.—The development of the Powder Wash field in northwestern Colorado was resumed in 1940 by the Mountain Fuel Supply Co., with the release of a location for No. 2-A Musser in the CWL.NW.SE. of sec. 4-1rN-97W. The Powder Wash field was discovered in 1931 by the Mountain Fuel Supply Co. and the discovery well, No. I Musser, on C.NW. of sec. 5-IIN-97W., was completed at 2152 ft. in the Hiawatha member of the nonmarine Wasatch for-mation for an open flow of 34,000,000 cu. ft. of gas per day under a natural pressure of 685 lb. per sq. inch. Oil was discovered in the Powder Wash field on Nov. 26, 1936, in the company's No. I Carl Allen on the NE.SW.SE. of sec. 32-12N-97W. The oil production was

Jan 1, 1941

By Howard N. Evanenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. AVERAGE RECOVERY The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered-it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal-is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1946

By R. E. Carter, C. Wagner, F. D. Richardson

By means of inert markers of radio-platinum, it has been shown that cobalt metal oxidizes by out-ward diffusion of cobalt atoms through the oxide. Oxidation rates have been measured at various temperatures and oxygen pressures and have been found to agree with the rates calculated from the Wagner equation and the authors' values for the diffusion coefficient of cobalt in the oxide. The distribution of radio-cobalt in growing oxide loyers has been accurately measured and found to be different from that predicted from the Wagner oxidation theory. Attempts have been made to measure the change of lattice parameter of the oxide with composition. SEVERAL investigators have shown that cobalt metal oxidizes according to the parabolic law,1-3 but no detailed study has been made of the oxidation mechanism. Cobaltous oxide has a metal-deficient lattice, but the defect concentration which is dependent on the oxygen pressure is only approximately known.' From the similarities in the structures of "CoO" and "FeO" and the rate laws governing the oxidation of cobalt and iron, Gulbransen- as suggested that cobalt, like iron," oxidizes by diffusion of cobaltous ions through the oxide layer. To substantiate this hypothesis, he has attempted to measure the oxidation rate of cobalt as a function of the oxygen pressure but has been able to report only that the rate depends on a "small" power of the pressure. On the other hand, Preece," Valensi,' and Arkharov' all have suggested from indirect evidence that oxygen diffuses through the COO to the metal-oxide interface. The present authors, in a previous paper,' have shown that the rate of diffusion of cobalt in cobaltous oxide is dependent on the oxygen pressure. In that investigation, they also found that cobaltous oxide disks made by complete oxidation of cobalt metal were porous at their centers (Fig. 5L, ref. 4). Both these facts strongly suggest that oxidation of the metal proceeds via outward diffusion of cations. In order to establish the mechanism unequivocally, oxidation experiments were made with inert radioactive platinum markers, and the dependence of oxidation rate on oxygen pressure was measured. In addition, an attempt was made to determine the form of the cation vacancy gradient, which the marker experiment showed must exist across a growing oxide layer. This was done by depositing radioactive Co on the surface of a cobalt disk and then measuring the tracer distribution across the oxide layer produced by partial oxidation of the metal. Finally, an X-ray examination was made in an attempt to find the expected change of lattice parameter of COO with oxygen pressure. Experimental The apparatus and materials used were substantially the same as those previously described by the authors.4 Marker Studies: The use of inert markers to follow oxidation reactions was first attempted by Pfeil" in 1929, and radioactive markers have recently been used by Davies et al.' In the investigation reported here, the markers were applied as an (NH4)2PtCI6 slurry in several thin streaks across both faces of four disks of cobalt metal 1 mm thick and 14 mm in diameter. The disks were then oxidized almost to completion at 1200°C in pure oxygen. After oxidation, they were mounted and sectioned and auto-radiographs were taken to locate the markers. Oxidation Rate: The oxidation rate of cobalt was measured at 1148°C at oxygen pressures ranging from 0.0055 to 1.0 atm and at 1000°, 1148", and 1350°C under 1 atm of oxygen. The rate was deter-

Jan 1, 1956