Search Documents

By S. A. Hovanessian

Analytical solutions are obtained for calculating the pressure distribution in rectangular fields due to injection and/or producing wells located anywhere within the field. The field is assumed to be homogeneous with either constant pressure or no-flow boundaries. These solutions are extended to include the calculation of average reservoir pressure and permeability from pressure build-up curves. Numerical examples are given to illustrate the application of equations to practical problems. INTRODUCTION Pressure distribution analyses are of considerable importance in the field of reservoir mechanics. A number of papers dealing with this subject have appeared in the petroleum literature. perrinel in 1956 presented a summary of the methods available for pressure build-up calculations and discussed the applicability of each in some detail. More recently (1958), Hazebroek, et a1,2 discussed a theoretical method for obtaining pressure distribution in a radial field. Also in 1958, Nisle3 gave a theoretical solution of the pressure distribution in a field extending to infinity with a partially penetrating line source at the origin. Mathews, et a1,4 applied the method of images to existing solutions for pressure distribution in radial fields and obtained expressions for calculating pressures in bounded reservoirs. However, a literature survey revealed that a general analytical solution for the pressure distribution in a rectangular field, with injection and/or production wells located anywhere within the field, was not available. Such a solution could be used to approximate the pressure distribution in a field the shape of which is nearly rectangular. Furthermore, it could be applied to pressure calculations pertaining to a single well taken from a system of wells which were drilled in a rectangular pattern. In this case the boundaries of the well drainage area are considered to be the perpendicular bisectors of the lines joining the well and its nearest neighbors. The basic problem considered in this paper consists of a rectangular field with either constant-pressure 01 no-flow boundaries and with either an injection or production well located anywhere within the field. The physical properties of the rock and fluids present are considered to be constant. Analytical expressions are obtained for the pressure distribution within the field during the production or injection periods. These expressions, which are infinite series, can be used to evaluate pressure at any point within the field as a function of time and position. For fields containing more than one well (production and/or injection), the solutions for each well acting independently are superposed. That is, at any point in the field, the pressures due to each injection 01. production well acting alone can be algebraically added to give the pressure resulting from all wells acting simultaneously. Evaluation of the series solutions given in this paper is readily accomplished by means of an electronic digital computer; and, in most cases, sufficient accuracy is obtained by setting the upper limits of summation at 20. These solutions are extended to include the calculation of average reservoir pressure and permeability from build-up data. A number of numerical examples are given to illustrate application of the solutions to actual field problems. ANALYTICAL SOLUTIONS The partial differential equation representing the pressure distribution in a homogeneous rectangular field (see Fig. I.), having a single source or sink of strength (2, can be written*

By Frank Corwin

I. INTRODUCTION. SINCE the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 7, 1913

By D. H. Shaffer, W. F. Harris, W. M. Hickam, M. H. Loeffler

Experiments have been performed on the quantitative addition to niobium of enriched isotopes 018 and 017 at the 0.1 - 40 micro-gram level and their subsequent recovery. A measured quantity of molecular oxygen of known isotopic concentration is added to niobium metal by oxidation. Recovery of the enriched isotopes as carbon monoxide is by the vacuum fusion technique. Quantitative determinations of the enriched isotopes are made in standard volumes at constant temperature using accurately calibrated micromanometers and the mass spectrometer as pressure measuring instruments. THE presence of low concentrations of nonmetallic impurities in metals can often adversely affect the physical properties of the metal. The increase in hardness and the embrittlement of refractory metals due to oxygen is well known. In metallurgical studies dealing with the diffusion rates or the effect of oxygen on the physical properties of refractory metals, it is often necessary to add small quantities of oxygen to the metal and later recover the total quantity present. It is desirable, therefore, to establish the accuracy with which microgram quantities of oxygen can be added to niobium and recovered by vacuum fusion. The successful addition of microgram quantities of oxygen to metals by the usual manometric techniques and the subsequent recovery by vacuum fusion is difficult because of the uncertainty in the accurate determination of the quantity of oxygen originally present in the metal and because of the chance of contamination by atmospheric oxygen. In order to minimize these uncertainties earlier workers have added quantities of O16 at levels much higher than the oxygen concentrations that are of interest.'-3 In order to eliminate the uncertainty associated with the O16 additions to metals at low microgram levels, experiments have been performed on the quantitative addition of oxygen highly enriched in O17 and O18 at the 0.1 to 40 pg level to niobium and the subsequent quantitative recovery of the isotopes by vacuum fusion. Since the natural abundance of O17 is 0.04 pct and of 0" is 0.2 pct this enriched oxygen provides a uniqueness from interference not achieved in earlier work.'-= A measured quantity of molecular oxygen of known isotopic concentration is diffused into the metal. Recovery of the isotopes in the form of carbon monoxide is by vacuum fusion. The total quantity of gas is determined in standard volumes at constant tempera- ture using accurately calibrated Consolidated Electrodynamics micromanometers and the mass spectrometer for pressure measurements. The molecular and isotopic composition is determined mass spectrometrically. APPARATUS A schematic of the oxygen addition apparatus is shown in Fig. 1. Take-offs are provided for the attachment of the isotope container and for sample bulbs which are used to transfer samples to the mass spectrometer. Metal valves are used throughout the system including the sample bulbs in order to achieve a vacuum of 10"6 mm Hg. Evacuation is accomplished with a 3-stage oil-diffusion pump backed by a mechanical pump. A liquid nitrogen trap is used to remove condensables and to prevent oil vapor from entering the system. A micromano-meter is used for pressure measurements. The furnace assembly is shown in Fig. 2. It consists of a quartz tube joined to the apparatus through a 40/W joint with Apiezon W low-pressure wax. The furnace cap, also a 40/W pyrex joint, is provided with a pyrex hook. The sample is suspended from this hook with a platinum wire. The total volume of the furnace section is 435 ml. All volumes were determined by expanding a known volume of gas at a known pressure into the evacuated system and re-measuring the pressure. Both the micromanometer used on the oxygen addition system and the micromanometer used on the mass spectrometer were compared to a precision

Jan 1, 1961

By Heribert Wiedemeier, Ali Khan

The tetnperature-conposition phase diagram of the syste,n MnS-CdS has been investigated over a range fro)n 600° to 1000° C. The small degree of solid solution on the MnS rich slde cornpared to the large CdS rich single-plzase region could be esplained by the difference in strzrctures of the cotnponents and the relative sizes of the metal ions. The change in lattice parameter as a function of cot)zposition is linear atzd jollous Vegavd's rule within experittzental limits of error. Mns and CdS have gained considerable attention in recent years because of their interesting solid state properties. In order to investigate such properties and thermodynamic quantities of mixed compositions of transition metal chalcogenides, it is necessary to establish their phase diagrams. Two earlier publications are concerned with the MnS-CdS system. Schnaase' found complete miscibility when MnS and CdS were co-precipitated in aqueous solutions at room temperature. However, there is evidence that the mixed crystals were not stable over the entire range of composition. roger's' investigation of the ternary system ZnS-CdS-MnS at 900" C indicates a solution of 48 mole pct MnS in CdS. During the course of this work which covers a temperature range from 600" to 100O° C, emphasis has been placed on the use of high-purity materials and well-defined modifications of starting products. EXPERIMENTAL Starting Materials. The stable green modification of MnS with NaCl structure was prepared by direct fusion of the elements and by chemical transport reaction. Stoichiometric amounts of manganese of 99.99+ pct purity and of sulfur of 99.999 pct purity from Gallard-Schlesinger Corp. were sealed in an evacuated quartz tube at a pressure of 10"5 mm Hg and annealed for 48 to 60 hr at 800°C. The quartz tubes used throughout this work were outgassed under high vacuum at a temperature of 90OU to 1000° C for 12 to 18 hr. For the synthesis of MnS by chemical transport3 stoichiometric ratios of elemental manganese and sulfur and small amounts of iodine were sealed under vacuum in a quartz tube, which was placed in the temperature gradient, 900/800-C, of a two zone furnace. Single crystals of MnS in form of platelets and octahedra were deposited at the cooler end of the tube. The manganese content was determined by EDTA titratin. A typical result of several analyses was 63.05 pct Mn which agreed well with the computed value, 63.14 pct. Commercially available CdS of 99.9+ pct purity, a mixture of the cubic and hexagonal forms, was converted into the hexagonal high-temperature modification by annealing CdS under vacuum in quartz tubes at 700° C for about 36 hr. As a second method, cadmium sulfide was transported in a temperature gradient, 70O° /650" C, with in vacuo sublimed iodine from the hot to the cooler zone of the tube. Large sized crystals in form of hexagonal columns and some platelets were obtained. An average result of the cadmium analysis by EDTA titration4 was 77.93 pct in good agreement with the computed value, 77.81 pct. Only the NaCl modification of MnS and the wurtzite modification of CdS were used for the solid solutions. Preparation of Solid Solutions. Finely powdered MnS and CdS samples were thoroughly mixed in molar ratios and compressed into pellets of about 6 mm diam and 2 mm in height at a pressure of approximately 13,500 atm.

Jan 1, 1969

By J. Peperakis

Coal mine bumps are normally associated with pillar mining under moderate or deep cover. Severe bumps at Sunnyside, however, have not been confined to pillar lines. Many have occurred in virgin development and in localities a long way from active pillar workings. As early as 1918 bumps in virgin territory were attributed to the faulted structure in the Sunnyside area.' Sunnyside is an old property, mined for more than 60 years. Both man-made and natural conditions contribute greatly to bump occurrences, and loss of life and great destruction of workings have resulted from some unusual bumps in recent years. Before Kaiser Steel acquired the Sunnyside Mines in 1950, about 21 million tons of coal had been extracted. Large areas had been worked out and equally large areas first-mined. As demand for coking coal gradually diminished, extensive blocks were shut down, and during the low production period of the 1930's mining on a very limited scale was confined to a section of the property close to the coal tipple. Following purchase of the property Kaiser Steel developed the mines into a fully modernized operation. The worked out and first mined areas covered about four square miles extending five miles along the strike and up to one and a half miles down dip from the outcrop. The sections with favorable mining conditions and clean coal had been largely extracted under the selective mining system imposed by economic conditions and the lack of cleaning plant facilities. Large reserves remained on the fringes of the worked out sections and in areas under deep cover and difficult roof. There were also considerable reserves in first-mined areas. In recent years much of Sunnyside's daily output of 7000 to 8000 tons has been derived from the partially mined localities. Many bumps have occurred when pillars have been pulled within the first-mined areas and on the fringes. The bumps have been associated with retreating pillar lines backing up against old workings and pillar lines in old first-mined areas backing up against highly stressed oversized barrier pillars surrounded by smaller pillars. In some parts of the property the upper Sunnyside seam was extensively worked in the past, and sizable areas of old works overlie the present lower seam workings. Abutment pressures from barrier pillars and pillar remnants are transmitted to the lower seam, contributing to bumps and squeeze conditions. Cover: The terrain is exceedingly rough, and cover varies considerably over relatively short horizontal distances. For example, at No. 1 mine the 2000-ft cover line is ony 2700 ft from the coal outcrop, and at No. 2 mine the cover over the main hoisting slope increases from 1000 to 2000 ft in a horizontal span of 1200 ft. Cover over the present mining sections ranges from several hundred feet in the valleys to 2500 ft under the crest of the divides. A short distance ahead of Sunnyside's deepest development down dip the cover reaches 3000 ft or more.

Jan 1, 1959

By Enid C. Plante

This paper deals with the flotation of the mineral fluorite (calcium fluoride) and of two associated gangue minerals, calcite and quartz. The aim of the investigation was to produce "acid-grade" fluorite, which must contain less than one per cent of silica. Several reagents are used successfully in practice for floating fluorite from its ores. Oleic acid is the most widely used collector, usually at temperatures above 60°C, with sodium silicate as a dispersant for quartz and quebracho or tannin to depress calcite. Sulphides (e.g., galena) are often removed first by xanthate flotation. Many investigators23 report results in which more than 80 pct of the fluorite is recovered in a concentrate assaying 96 pct or more of fluorite and less than I pct of silica. This investigation was undertaken with the intention of floating the gangue, which is the minor constituent of the ore, from the fluorite. Hence emphasis was first placed on the cationic compounds that float quartz. No satisfactory separations were obtained in this way, and other reagents were investigated to discover whether these were more effective than oleic acid in floating fluorite from quartz in the usual way. The first part of the paper describes experiments with several long-chain collectors available commercially. Most of this work has been by captive-bubble and cylinder flotation tests, with some batch tests in a flotation machine. The second part describes the use of sodium cetyl sulphate as a collector for fluorite and includes laboratory tests and extension of the work to batch tests in the flotation machine. A method for determining the adsorption of sodium cetyl sulphate on fluorite has been developed and is described. Theory of Collection by Paraffin-chain Salts It may be assumed that these compounds are adsorbed at the mineral surface in one or more of three ways outlined by Kolthoff:12 1. Exchange adsorption between lattice ions in the mineral surface and collector ions in solution. Closely related is adsorption by the collecting mechanism postulated by Taggart,17 in which there is metathesis between the collector and the mineral cation or anion. 2. Exchange .adsorption between adsorbed gegen ions (p. 67, ref. 19) and collector ions in solution. 3. Adsorption of nonelectrolytes (polar-nonpolar) without displacement of adsorbed ions. With cationic collectors, inorganic cations in the solution (e.g., hydrogen ion) compete with the collector ions and therefore act as depressants, while inorganic anions have the same effect with anionic collectors. From this follows the general conclusion that ions of the same charge as

Jan 1, 1949

S. Tandanand, Twin Cities Mining Research Center, U. S. Bureau of Mines As an addition to the fine reviews on drilling presented in the foregoing papers, we feel it would be appropriate to mention briefly some work in this area by the U. S. Bureau of Mines. The Bureau has had under way for several years at its Twin Cities Mining Research Center studies directed toward a better understanding of basic drilling mechanisms. The work includes drillability investigations with diamond rotary, and with percussive drilling systems, as well as fundamental studies of rock behavior under drill bit types of loading. Results of our work to date have contributed the following to the state of the art. MECHANISM OF ROCK FAILURE-Rock fragmentation through use of mechanical energy systems, including drilling systems, consists of two major components-machine and rock. The two components are related to each other by their functional behavior and their resultant motion which the components mutually influence. Forces in the systems are transmitted directly to the bit which in turn induces stresses in the rock. When the induced stresses exceed the strength of the rock, the rock fails resulting in penetration. Rock strength is a function of the forces applied to the rock. Stresses under a drill bit, regardless of bit configurations, are essentially compressive, resulting in a condition where the rock has the highest resistance to failure. The ratio of principal stresses induced under drill bits is an indication of the mode of failure in the rocks. Initially, compressive stresses under the drill bit cause rock to undergo inelastic deformation. The impression observed at the first stage of crater formation under the drill bit shows that rock is no longer elastic. Associated subsurface failure at this stage precedes total rupture which subsequently appears at the rock surface. Thus, explanation of crater formation, by applying theory of elasticity alone, is likely to be over-simplified. ENERGY VERSUS VOLUME OF ROCK REMOVED-Experimental results show that energy per unit volume of rock removed is constant for a particular rock and bit type. Rock offers a definite resistance to penetration, depending on the method of the energy application; this may be defined as the drilling strength of a rock. Energy consumption in a drilling system may be divided into two components: 1) Energy required to move the machine parts; and 2) energy consumption in breaking rock. Component 1 is dependent on the type of the machine. Component 2 is dependent on the strength properties of rock and the efficiency of the bit in rock cutting. The sum of the energy required in both components determines the total energy required in breaking rock. Our work in this area has included consideration of both diamond and percussive drilling systems. PENETRATION RATE-For a drilling rate expression to be useful in predicting field performance, it should include the operating characteristics of the drilling machine. Eq. 37, for example, is simply a statement of the fact that the drilling rate is determined by the power output of the machine (2pNT) and the power requirements to break the rock in the hole (AER). In order to predict the performance of a particular drill and the effect, for example, of the rotary speed, on the drilling rate, R, Eq. 37 must be modified to include the

Jan 1, 1967

By J. B. Hess, R. L. Dietrich

In the mechanical twinning of magnesium on the {1012} planes the crystal-lographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only undef tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [1120] fibers,' the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to ( 1or2 ) twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or un-twinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig I is the pattern of an uncompressed specimen of AZ3I alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on (1072 planes produced an 86" reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1949

By S. E. Buckley, M. C. Leverett

THE production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. INTRODUCTION Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,1 and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. ROLE OF DISSOLVED GAS When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1941

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for upgrading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching. ALL of our larger domestic deposits of manganese are very low grade, but estimated tonnages in these deposits are large enough to constitute a potential strategic reserve of manganese for emergency periods, provided these ores can be upgraded sufficiently to meet industrial specifications. Many types of processes have been suggested for upgrading these ores, several have been studied in pilot plants, and a few have attained limited commercial production for special purposes. The hydrometallurgical process to be described below proposes a leaching operation for removing caustic-soluble silica and other gangue minerals and consequently upgrading a manganese ore or flotation concentrate to a commercially acceptable moduct. It is known that some forms of silica and some silicate minerals are soluble in NaOH solutions under suitable conditions. This new process proposes to use NaOH for removing the soluble materials from manganese ores or concentrates and, as a result, upgrade the manganese content. Since spent leach liquors are not efficient leaching agents the liquor must be treated with lime to precipitate calcium silicate and reactivate the NaOH. Experimental Procedure Manganese-ore samples ground to —35 mesh were leached in iron containers into which the ore sample and appropriate NaOH solutions were placed. Flotation concentrates were already ground to —200 mesh. The slurries were then placed on a hot plate or into a pressure digester and stirred continuously during the period of digestion. Where the- digestion was performed at atmospheric pressures, water lost by evaporation was replaced at regular intervals to maintain approximately a constant volume of slurry. In the pressure digester, volume changes were not controlled. After digestion, the slurry was allowed to cool enough for easy handling, but it was filtered hot, 50" to 70°C, on a Buechner filter. Filtration under these conditions was satisfactory. The resulting filter cake was washed and dried. In most instances, a single leach would not produce maximum extraction of silica from the ore sample; consequently, the dried tailing was treated again in the same manner with a fresh solution of NaOH to obtain an additional extraction of silica. This procedure was repeated a number of times to get the maximum extraction of silica. Usually three or at most four stages of leaching were adequate for this purpose. This leaching procedure was used for obtaining the data reported in this paper on the effects of NaOH concentration, pulp dilution, temperature, and time of digestion on the efficiency of extraction of silica from the ore sample. The experimental procedure does not match industrial methods. consequently tests for counter-current leaching were set up. Data from these tests are not yet complete, but in a qualitative way they indicate that thickeners between stages of leaching will be satisfactory and that the quantity of silica in a leach liquor moving forward to a new solid has only a minor effect on the quantity of silica extracted from the new solid. A pilot plant is now being designed for operation in the near future to test and evaluate the merits of this process.

Jan 1, 1954

By John W. Gabelman

Uranium exploration technology historically has followed the economic cycle of demand, exploration spurt, and trailing supply; but with a greater lag. Greatest progress was made during the wane of demand as geological investigation caught up with the flood of new discoveries made during relatively short periods of peak demand. Updating brought technology to a new level based on the deposits which were discovered and not on the total range of deposit types which might exist. The technology was seldom able to predict new deposit types or new districts, which have consistently been surprises. Yet each new cycle of increased demand was at a new higher level, occasioned by a new use, which required the discovery of previously unrecognized larger types of deposits. Hindsight shows that data sufficient to have predicted most discoveries were available. The predicted growth of uranium demand far in excess of estimated resources is an incentive to examine current technology for data or promising techniques that might foster discovery by technical prediction rather than by systematic drilling. The world could well be reexamined systematically with new geophysical techniques including gamma spectrometry, radon emanometry, and magnetometry. Known occurrences could well be reevaluated in the light of new data on mineralization process and supergene leaching. Less-leachable extrinsic elements associated with uranium might he sought as clues to unleached uranium at depth. Uranium is increasingly being noted in environments containing coal and petroleum which might become targets. High-temperature replacement disseminations are increasingly reported and particularly attractive as exemplified by the Rossing district. The number of formations containing uranium occurrences is growing so that new, not necessarily fluvial, formations might be productive. Enough drilling has been done to indicate that uranium is selectively distributed regionally under some control yet to be determined. Exploration should address those environments and areas where uranium could occur rather than only those where it is already known.

Jan 1, 1976

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By Gerard Matthes

WITHIN the last three years, aerial mapping has made wonderful progress. Its three sources of development in North America may be enumerated as follows: (1) The work of the U. S. Army Air. Service and Corps of Engineers at the McCook Experimental Field, Dayton, Ohio. This is generally regarded as the backbone of this class of endeavor in the United States. (2) In Canada, a great deal has been accomplished in a practical way by methods that have not even been tried out in the United States. Under the leadership of the late Doctor Deville, the Dominion Land Surveyors have turned out reconnaissance maps of large areas at very, small cost. (3) Private capital has contributed a great deal toward development of aerial mapping in a practical way in the United States. Prominent in this regard stands the Fairchild Aerial Surveys, Inc. which has spent large sums in research and development work, especially in the construction of aerial cameras. Its camera is, at present, the official camera of the U. S. Army and Navy Air Services, also, of the Canadian and Brazilian governments. Aerial photographic surveying is a flexible process and adapted to a variety of uses. To date, it has proved. of direct practical value for engineering projects such as reservoir and power transmission surveys, railroad location, drainage, harbor front studies; also, for many commercial purposes, tax assessment, city planning, forest surveys, and lawsuits. In a few instances, aerial photographs have been used successfully by geologists as base maps on which to record field observations, thereby dispensing with pacing and compass surveys. There is reason to believe that, eventually, the aerial map will find wide application in the work of geologists. The reason for advancing this opinion is that aerial maps have, in other fields, proved more complete as regards detail than maps made by standard processes of surveying and drafting, and often are more accurate than the latter. At the present time, five distinct uses are being made of aerial photographs: There is the "oblique" photograph taken at an angle with the horizon; it is used extensively for illustrations in newspapers, magazines, and advertisements. Also, for reconnaissance purposes, it has been found of great practical value. For illustrating reports of engineers and geologists, it offers many obvious advantages. In the Canadian Surveys, maps have been compiled from oblique photographs.

Jan 3, 1925

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By V. Patarini, M. Salkind

BECAUSE of its high strength and stiffness coupled with low density, continuous boron filament is showing great promise as a potential reinforcement for both metals and nonmetals. Of primary consideration for structural applications is the fatigue behavior of boron fiber composites. Composite fatigue behavior is dependent upon three factors: 1) fiber fatigue behavior, 2) matrix fatigue behavior, and 3) the effect of the interface and fiber ends. The purpose of this note is to describe the behavior of boron filament in rotating beam fatigue. The filament, described by Talley' and Galasso, Salkind, Kuehl, and Patarini,' was made by the hydrogen reduction of boron trichloride on a hot tungsten filament. Testing was performed using a commercial rotating beam wire fatigue tester* described by Votta.~ One end of the test sample is held in a chuck in a synchronous motor. The sample is bent around in a "U" shape, and the other end inserted into a carbide bushing. The maximum strain occurs at the bottom of the "U" where the radius of curvature is a minimum. The strain is adjusted by adjusting the length of the specimen and the location of the bushing. Samples were rotated at 3600 rpm and an automatic shutoff device used to determine the number of cycles to failure. The measurements were accurate to the nearest 360 cycles. The fatigue behavior is summarized in Fig. 1 for fifty-one samples of 4.8 x 10"3 in. diam fibers and ten samples of 3.2 X 10"3 in. diam fiber. The two sample groups represent two different filament production runs and two different nominal size groups. Both groups exhibited nominal tensile strengths of 400,000 psi. No significant difference in the fatigue behavior of the two sample groups is apparent. The scatter in the data is not unexpected for a brittle filament which exhibits a tensile strength distribution with a standard deviation of 10 to 15 pct. Because the test procedure provides a known outer fiber strain in the sample, the maximum stress was calculated assuming a Young's modulus of 58 x 10' psi. This value was selected as being representative of several nominal fiber sizes.2 All of the samples which failed exhibited sudden, catastrophic fracture, and no permanent deformation. One sample was stopped after 1.66 x lo8 cycles at *200,000 psi. The fiber exhibited no apparent damage or deformation. It is apparent that the fatigue resistance of boron filament is quite good. It can therefore be speculated that the fatigue behavior of boron fiber composites would be controlled by the "weaker links", namely matrix fatigue resistance and interface behavior. In fact, preliminary investigations have revealed that this is true for boron-reinforced aluminum? It should be noted that the data presented herein may not necessarily reflect the tensile fatigue behavior of boron filament. It is well-known that boron filament has a radial residual stress pattern with the outer surface in ~om~ression.~ Because of this fact, tensile failure is normally nucleated in the interior of the filament.5 Since the data presented herein is for a rotating beam test in which only the outer surface of the fiber is stressed to the maximum value, it would be incorrect to assume that the failure mechanism and fatigue behavior would be the same if the fiber were tested in tensile fatigue. The fact that many of the data are well above the nominal 400,000 psi tensile strength would tend to support this argument. The authors would like to express their appreciation to the United Aircraft Research Laboratories for supporting this investigation and for permission to publish the results. A portion of this effort was supported by the Air Force Materials Laboratory under contract AF33(615)-2125.

Jan 1, 1968

By C. Elbaum

Specimens consisting of several crystals, each with a prescribed geometry and a controlled orientation with respect to both the extermally intposed stress and the highboring crystals, werer deformed in tension at room temperature. It is shown that the influence of a grain boundary on the plastic defolrmation of a mullicrystal depends on the extent to which the presence of the grain boundary, contributes to the necessity 01. multiple slip in the component crystals. MANY investigations were carried out in the past on the plastic deformation of aluminum single crystals, bicrystals, and polycrystals. The various studies of bicrystals aimed primarily at elucidating the influence of grain boundaries on the mechanisms of plastic deformation. In the earlier studies the emphasis was placed primarily on finding the "strength" contributed by a grain boundary. In more recent investigations it became apparent that the grain boundary does not contribute any strength per se but rather acts by influencing the mechanism of plastic deformation in the adjoining grains. The concept thus emerged of the plastic properties of a bi-crystal, and by extension of a polycrystal. depending solely on the mechanism of deformation prevailing in each grain. The contribution of the grain boundaries thus becomes limited to the type of restrictions imposed on each grain by its neighbors. The present investigation of the behavior of specimens consisting of more than two crystals was designed for the purpose of studying the influence of the grain boundary in simple aggregates. The findings of this study further support the concept that the restriction imposed on a deforming crystal by its neighbor constitutes the predominant factor in the plastic deformation of polycrystals. The term "multicrystal", in contrast with single and polycrystals, is used to describe specimens consisting of several crystals. Each one of the component crystals has a prescribed geometry and a controlled orientation with respect to both the externally imposed stress and the neighboring crystals. Two groups of multicrystals were prepared. All the component crystals of both groups of multicrystals had the axial orientation (isoaxial multicrystals) shown in Fig. 2, with the primary slip plane and slip direction both at 45 deg to the specimen axis. In the first group (hereafter referred to as group I) the component crystals were symmetrically oriented with respect to the plane of the grain boundary; the primary slip plane and slip direction were respectively at an angle of 60 and 30 deg to this plane. For the second group (group 11) the axial orientation remained the same and the relative positions of the primary slip plane and slip direction are shown in Fig. 3. EXPERIMENTAL METHODS The material used was aluminum 99.993 pct pure, according to the manufacturer. The specimens were produced by growth from the melt in a horizontal graphite container. In order to maintain the prescribed geometry of the individual crystals of a multicrystal, a technique described elsewhere was used.' The specimens were grown under a small, positive pressure of helium at a rate of approximately 1 mm per min. annealed in air for 24 hr at 640°C and cooled over a period of several hours to room temperature. All the multi-crystals were rectangular in cross-section, 6 by 18 mm (see Fig. 1) and from 150 to 170 mm long. In each group bicrystals, tricrystals and quadru-crystals were prepared as shown in Figs. 1 and 4.

Jan 1, 1961

By Dean Goodermote, Carla S. Stone

I Introduction Coal fuels China. Roughly 70 percent of all commercial energy demand is supplied by domestic coal production and with the recent Chinese opening to the West, the Chinese Coal Industry may figure prominently in the export market as well. Because of the importance of China's coal industry to the future of China and the Pacific Rim energy balance, this paper reviews the industry and offers some cautious projections for its outlook. II Energy's Position in the Current Political and Economic Climate Traditionally, Chinese society has been dominated by the policies of its most important government leaders. Deng Xiaoping, Vice Chairman of the Communist Party is the current leader of China. Deng and his proteges are pragmatists. Although China's government structure is based on Marxist/Leninist tradition, Deng and his followers are promoting experiments with market economics and expanded relationships with Western Countries, which have encouraged foreign investment in China. Energy companies represent just one type of industry that is interested in helping the Chinese to develop their abundant natural resources. Although China's leadership is committed to a program of economic modernization, that program currently is experiencing what the Chinese government terms "readjustment". Readjustment cuts back in imports due to deficient foreign exchange and deemphasizes heavy industry, while it encourages agricultural and consumer goods output and, most imporant, energy production. Increased Chinese coal and oil production is essential both to fuel industry and, equally important, to provide foreign exchange. If sufficient energy production is not forthcoming, then economic growth will be severely retarded. China's 1979 per capita GNP of $260 is only slightly better than the weighted average achieved by low income countries of $230. (1) Delays in growth could lead to social unrest, threatening the position of the current leadership. Since there is no institutionalized mechanism for leadership succession and policy continuation, it is reasonable to assume that leadership changes could result in energy policy changes. III Energy Consumption Energy production is important to China's future economic health as highlighted by the World Bank. If China's economy grows rapidly, 5 percent to 6 percent during this decade, the Bank noted, a significant energy shortfall could occur as early as 1985. This state of affairs contrasts sharply with China's current position as a net hydrocarbon exporter. (2) To assure a healthy economic future, China's leadership is attempting to reduce its rate of increase in energy demand through conservation as well as to boost energy output. A massive conservation promotion program has been underway since 1979 and there is much room for improvement. China's industrial sector is only about half as energy efficient as is U.S. industry. (3) During the last two decades, each percent of increase in GNP has been accompanied by a 1.8 percent of increase in energy consumption. (4) This compares rather poorly with the United States where a less than one-to-one relationship exists. IV Energy Supply The short term prospects for oil production are uncertain. Production increases were rapid in the 1960's and early 1970's, averaging 20 percent annually, but most of this increase came from one field, Daquing. Now that Daquing's production has peaked and the offshore potential has yet to be developed, petroleum production has maintained a plateau of 2.1 million b/d, at least temporarily, of which approximately 15 percent is exported. (5) Output

Jan 1, 1982

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By J. J. Hauser, H. C. Theuerer

A cathode sputtering technique is described which elin7inates the need for ultrahigh vacuum in preparing thin films of materials sensitive to gaseous impurities. This technique uses a fraction of the atoms sputtering within an anode container to getter actice gases, such as HzO, Oz, and Nz. The gases alzd gettering metal are deposited on the container walls, thus shielding the coating zone of the system from contamination. The use of the method for preparing superconducting-normal metal couples such as Ph-Cu and Ph-Pt is described, and the properties of the individual and composite films are given and discussed. GETTER sputtering is a method which greatly simplifies the preparation of thin films in cases where composition control is critical. A major difficulty with conventional sputtering and other vacuum-deposition techniques is the contamination of the forming film caused by residual gases, such as H20, CO, Oz, and Nz, in the coating equipment. The difficulty arises from the fact that even when the residual pressure in the system is as low as 1 x 10"6 Torr, with a deposition rate of 10A per sec, there are as many contaminating gas collisions with the substrate as there are with film-forming metallic atoms. It is not surprising, therefore, that with reactive metals, such as tantalum and niobium or with semiconductors, such as silicon and germanium, films with properties far different from the starting materials are obtained. In the case of niobium and tantalum, deposited either by sputtering or vacuum evaporation in systems with reactive gases at pressures of the order of 1 x l0-' Torr, the loss of superconductivity is traceable to interstial oxygen or nitrogen. On the other hand, working in vacuum of the order of 1 x l0-" Torr, Marchand and enema' have shown that superconducting films of tantalum with properties approaching those of bulk material are possible. At this level of gaseous impurities -lo6 metallic atoms arrive at the substrate before a contaminating collision occurs again assuming a deposition rate of 10A per sec. It is evident from the above that any successful vacuum technique requires the elimination of reactive gases from the region of the system where coating is occurring. Getter sputtering accomplishes this using conventional vacuum equipment with residual pressures in the 106 Torr range. In fact? vacuum systems with residual pressures of lo-" Torr are adequate for most purposes. With this method, sputtering is confined within an anode can and, by geometric design, sputtering itself is used to purify the argon at the lower and upper parts of the system by the gettering action of the reactive metal. In consequence, the central region of the system where coating occurs is shielded from gaseous contamination. Getter sputtering is particularly useful for the preparation of alloy and compound films. With this method, if a cathode of homogeneous composition is bombarded with high-energy argon ions, transfer of material to the substrate having the same composition as the cathode will occur. This is true after an initial equilibration time, even though the constituents of the cathode may have different sputtering rates. During equilibration, the surface of the cathode changes composition due to differences in sputtering rate, but mass conservation demands a steady-state condition such that the atoms sputtered from the surface have the same composition as the cathode material from which the surface is generated. GETTER-SPUTTERING APPARATUS The original form2 of the getter-sputtering apparatus is shown in Fig. 1. It consists of a closed nickel or stainless-steel can 4 in. tall and 2-3/8 in. in diameter. Mounted symmetrically from each end

Jan 1, 1965