Search Documents

By William Hurst

This is a presentation of the diffusivity theory for the calculation of the water drive on an oil reservoir in which the history of reservoir pressure with time are the essential parameters for the determination of the rate and cumulative water encroachment into a field. The main body of the paper is essentially the application of the principles underlined here to actual field data. It consists of the work plots of the radial-flow case, and includes a discussion of an illustrated problem for which the water-drive calculations are treated in conjunction with the volumetric-balance equation. The appendix is a mathematical treatment of the linear, radial, and spherical cases of water influx into a reservoir. Introduction The evaluation of oil reserves and the prediction of pressure behavior with different rates of production are related to the volumetric balance of the fluids entering and leaving the space occupied by the oil and gas originally present in the formation; that is to say, important information can be gleaned from a volumetric study of the oil, gas, and water produced from a formation as it affects the extent of change in volume of oil zone, the gas cap, and the amount of water influx from the adjoining water sands. It is not the purpose of this paper to enter into a discussion of the equation of volumetric balance, in which such pertinent information as subsurface sampling and the measurement of reservoir pressures play a predominant part, as this has been discussed in detail by others.1,2 However, there is an inherent difficulty that has limited the general application of this equation to a study of oil reservoirs; that is, the insufficient knowledge of the analytics for expressing the water drive on a field as a function of reservoir pressure. This to a large degree has been overcome and it is the purpose of this paper to present this theory in such form as to be applicable for reservoir calculations. Water Drive If the amount of oil originally in place and the gas space are known, it is a relatively simple matter to determine, by the volumetric equation, the cumulative water influx into a reservoir from the adjoining water sands. Often, however, the oil reserve as well as water influx must be 'determined, and in order to be able to make this calculation it is essential to assign a mathematical relationship for the varying water term that is compatible with conditions known to exist in the formation and gives an accuracy acceptable for engineering calculations. Various equations have been employed empirically by different investigators in making reservoir studies of water drive. One form used by Schilthuis2 expresses the rate of water influx into a reservoir at any time as proportional to the pressure

Jan 1, 1943

By H. A. Schwartz

From time to time, one of the authors has had occasion to investigate the graphitizing reaction and has published the results mainly as discussion' of the work of other investigators. In view, therefore, of the diversity of both observations and interpretation, it seemed well to attempt, a revision of the entire subject in the Research Laboratory of the National Malleable Castings Co. The work consisted of a careful study of a single, impure, iron-carbon alloy. The material, which may be considered typical low-carbon white cast iron of the malleable industry, was an air-furnace iron of the following composit,ion: carbon 2.30 per cent., silicon 1.20 per cent., manganese 0.29 per cent., phosphorus 0.156 per cent., sulfur 0.048 per cent. The freezing range extended from 1213' to 1132' C., the latter figure agreeing with Gontermann's data.2 We have attempted to define the equilibrium diagram of this alloy, in the stable condition as related to the mctastable diagr,aui,- from a temperature somewhat below the euteetic freezing point to a temperature l>clow Arl and for a graphitic-carbon content from practically notliing to the original total rarbon of the specimen (see Fig. 6). More csp~c~ially we desired to locate the line in the stable diagra~n corrcspo~idi~lg to thc Ac, line of the metastable syst,ern, which is designated by analogy, thc At, line (t, from tcrnpcr carbon); also to dctermirle the locat'ion of A tm witah respect, to Acm t,o~vard their lowcr extremities at Arl in ordei to determine whether or not graphitization is completed by th~ separation of an iron-carbon entectoid analogous to pearlite in the iron-cementite system. This would involvc furthcr a colnparison of thc locations of Ihc stablc and met.astable 41 points. As the carbon concelltrations of thc solid solutions of the two syste~~ls are probably not, identical, an explanation of t>lieir differences and of thc,

Jan 1, 1923

By J. G. Mravec

The SO-called gas-tube method as developed by Hare, Peterson and Soler for determining the type and content of gases in molten steel is particularly adapted for determining the hydrogen content in molten steel. The development of this method has been quite completely discussed in a paper published by these co-workers in 1937.' The purpose of this paper, therefore, is to familiarize with this method those who arc not well acquainted with it. The principle of the gas-tube method is as fol1ows: One end of an evacuated gas tube is sealed with a very thin copper disk. when this end of the tube is immersed in a test spoonful of molten steel, the copper disk melts almost immediately, allowing a portion of the steel to be drawn up into the evacuated space. Any dissolved gases, and those produced by reactions between the components of the steel during freezing, are liberated into the unfilled portion of the sampling tube. A blob of steel that forms on the immersed end of the tube after the sample is drawn up seals up the end, making it airtight again. The evolved gases are subsequently drawn out of the gas tube through a suitable valve and analyzed by means of an Orsat apparatus. The volume of the sampling tube is sufficiently large so that a pressure considerably below atmospheric is produced after the gas evolution. The low pressure is necessary to effect a nearly complete removal of gases from the steel. Construction oF Sampling Tube The sampling gas-tube apparatus is illustrated in Fig. I. Seamless S.A.E. tubing used for section A is first cut into 7-ft. lengths. Through cxperiencc it was found necessary to use two sizes of tubing for this part, "is-in. and 3/4-in., respectively. The smaller tubing is generally used on the hotter or lower carbon steels. If the inside wall of the tube A is coated with grease or oil, it should be burned out before being machined as follows: One end is machined on the inside diameter to a depth of 34 in., so as to form a seat for a 7/8-in copper disk, which is stamped out from 0.005 to 0.007-in. thick copper sheet. The other end is machined on the outside diameter to a diameter of 1 5/16 in., to take a small reservoir or trap member I?. About 4 in. below the same end, a 1/2-in. hole is drilled to receive the 1/2-in. copper tubing leading to the large reservoir C. The inside of tube A is then thoroughly cleaned with a round wire brush, such as is generally used to clean out shotgun barrels. It is very important that the surface be absolutely free of rust or any nonmetallic coating. Next, the thin copper disk is soldered in place with low-melting silver solder.

Jan 1, 1945

By John R. Caldon

INTRODUCTION Leasing has become a major industry in many countries because of the advantages it affords. Whilst the accounting, legal and tax treatment of leasing varies from country to country, there is far more similarity than difference. The general approach to the subject is largely the same. This paper looks to the basic financial considerations in the decision to lease or buy. TYPES OF LEASES Before embarking upon the subject, it would seem appropriate to define a "lease". A lease may be defined as: "an agreement granting one party the right to use, for a specified period of time, property owned by another party in return for a series of payments of rental by the user to the owner''. Ownership, of course, generally entitles the owner to unrestricted use of the asset over its useful life in contrast to a lease which gives the lessee use over a limited period. The distinction between the status of owner and a lessee often is fairly small. In this case we are dealing with what is generally termed a "finance lease". A finance lease is one which substantially transfers the risks and benefits of ownership from the legal owner to the lessee. For example, a finance lease would exist where the lessee enters into a lease of an asset for most of its useful life and has an option to buy the asset at the end of the lease for a price which takes cognisance of the rentals already paid. Where a lease does not substantially transfer the benefits and risks of ownership to the lessee, i.e. those benefits and risks remain with the owner and lessor, the lease is termed an "operating lease" and is an agreement for the renting and usage by the lessee of an asset owned by the lessor for a limited period. An example of an operating lease might be where a tenant leases a building for a defined period say 6 years with the rent and occupancy subject to renegotiation at the end of the lease term. The economic consequences of the distinction between a finance and an operating lease is very important. With a finance lease, the lessee has a de facto economic interest in the asset and the alternative to a finance lease is some form of purchase; with an operating lease, the lessee does not have a basic economic interest in the asset and consequently a comparison with a purchase option involves far more than simply a funding comparison. Some of the principal differences between finance and operating leases can be summarised as follows: (a) finance leases: -the risks and benefits of ownership are substantially transferred to the lessee; -the lessor normally recovers his investment during the term of the lease; -the lessor in entering into the transaction is relying more on the creditworthiness of the lessee than the underlying value of the asset; - the lease is either non-cancellable or a large penalty will apply for unilateral cancellation by the lessee; (b) operating leases -the risks and benefits of ownership remain essentially with the lessor; -the lease rental income would not normally cover the recovery of the lessor's investment; -the lessor evaluates his risk in terms of the underlying value of the assets;

Jan 1, 1985

By B. K. Larkin, H. K. van Poollen, H. C. Bixel

A detailed treatment is given of the transient pressure behavior of a well located near a linear discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility, and porosity are uniform, but may be different from those on the other side of the discontinuity. These results generalize previously published works which assumed the permeability ratio for media on different sides of the discontinuity was zero, one, or infinity. One application of this material would be to facilitate detection of facies changes or fluid-fluid contacts by transient testing. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables examined includes dimensionless time from 0.1 to 100, rnohility ratio from 0.001 to 1000 and specific compressibility ratio from 0.001 to 1000. For dimensionless tinze less than 0.4, the pressure behavior is essentially that of a well in an infinite reservoir. Thus, reservoir properties near the well may be estimated in the usual manner. Using an overlay technique to match an experimental curve with one of the theoretical curves, it is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time , at which a match occurs into the equation where is the diffusivity near the well, and may be estimated from data taken at early time. Because of both the complexity of the solutions and limited computer facilities, well interference problems were not examined extensively. However, it was found that well interference may be masked by the discontinuity in some cases. By superposition of the results of constant rate fluid production, the problenz of pressure buildup may be treated. Such results show that for early shut-in times correct values for the transnzissibility are obtained from conventional semilog plotting. However, erroneous values of the static reservoir pressure are obtained unless data at large shut-in times are taken. INTRODUCTION Transient well testing has yielded estimates of such reservoir parameters as static reservoir pressure, permeability. porosity, and well bore effects. In most tests, it was assumed that the reservoirs were homogeneous and iso-tropic. Anisotropic media' and radial discontinuities were considered.'.' Various studies have been made on multiple-layer reservoirs." ' Linear discontinuities have been described for problems of one-dimensional flow.' In the present paper, a mathematical treatment is given for a well located near a linear discontinuity in an otherwise infinite medium (see Fig. 1). An actual reservoir analogy would be a well in a relatively thin reservoir near a fluid-fluid contact, or a well located in a reservoir exhibiting a sudden change in rock and formation characteristics, such as thickness, porosity, or permeability. A sudden change in porosity or permeability may be caused by clay fill or other types of facies changes. Sudden thickness changes niay be the result of such geological formations as buried shore lines and channel deposits. In otherwise uniform formations, a linear discontinuity may be caused by fluid-fluid interfaces such as oil-water contacts. 3s-oil contacts, or gas-water contacts.

By E. H. Citron

CLEANING fine coal in jigs is not new in Europe, where the feldspar jig is being used almost exclusively for this purpose. A feldspar jig operates with an artificial bed made up generally of feldspar or other hard rock material. Dimensions and specific gravity of this material must be of suitable values for good bedding qualities. For good efficiency, the size should range between 1x2 in. and 2x2x½ in. thick. The disadvantage of an artificial bed is that it is not mobile and must be replaced every so often with new material to obtain good cleavage characteristics. A semi-mobile bed has been developed to retain only a part of the feldspar on the sieve screen— the other part is drawn off with the refuse material, from which it is reclaimed and returned to the jig feed. Recirculating this feldspar rock offers definite advantages. However, in time it will lose its original shape because of wear, and new bed material must be added to the jig feed. The latest feldspar jigs arc generally air-pulsated, Baum-type jigs, although more than 70 pct of the feldspar jigs operating in Continental Europe are still of the piston type. These jigs are very popular in Europe, but they do require a great deal of time and attention. New Theory to Eliminate Artificial Bedding: At the preparation plants of Pittsburg & Midway Coal Mining Co. it has always been the contention that a small piston-type jig could be developed to clean fine 1/4x0-in. coal down to 28 to 60 mesh efficiently by obtaining and admitting bedding material from the present plant refuse circuit to the jig feed. This eliminates use of artificial bedding materials. The jig should incorporate these essential adjustable features as follows: Adjustable Sieve Screen A screen that can be raised and lowered to increase or decrease washing compartment depth. The sieve screen also can be set on an incline level, or decline. Adjustable Plunger Eccentric Length of stroke can be adjusted to increase or decrease pulsion and suction. Variable Plunger Speed Variable speed reducer for decreasing and increasing the number of strokes per minute. Water Distribution Adjustable baffle plate separating the plunger and sieve compartment so the water can be distributed uniformly over the entire sieve screen area. Refuse Ejector Special unique rubber-type refuse ejector gate operated by air and electrically controlled (as a conventional jig). Automatic Control Conventional float that measures the specific gravity of the coal-water refuse medium in the jig is of the submerged type. The float is mounted on a vertical stem held in position by two parallel arms. A movable weight regulates the effective specific gravity of the float. The float stem can be raised and lowered, having a graduated scale to indicate the depth of bed for the setting of the float. Hutch Drawoff Hutch material is drawn from the cell compartment to the elevator compartment by gravity. The first one-cell experimental jig incorporating all these features was built in January 1955 by Ore

Jan 1, 1959

By Charles A. Anderson

The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystalli-zation of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, prticularly at their intersection or where the faults are closely spaced. Introduction A major objective in a regional geologic study of a mining district is to determine whether any structural pattern can be found that has a bearing on the control of mineralization. The Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a.quartz monzonite stock which is located essentially at the intersection of two dike swarms (Fig 2). Of several quartz monzonite stocks in the area only this One is appreciably fractured and mineralized. The origin of the minute mineralized fractures in disseminated copper deposits has long been a challenging problem to the mining geologist, and evidence has been obtained to suggest that the mineralized fractures at Bagdad are related to a regional pattern of conjugate shears which also controlled the location of the dike swarms. The purpose of this paper is to Present this evidence and to emphasize the structural control of the supergene enrichment in forming a chalcocite zone that has provided the ore for the Bagdad mine. The field work on which these conclusions are based was done between October 1943 and August 1945, as a part of the copper investigations of the Goelogical Survey, U. S. Department of the Interior. The writer and his associates, E. A. Scholz and J. D. Strobell, Jr., have prepared a comprehensive report on the geology and ore deposits of the Bagdad area which will be published subsequently by the Geological Survey. Bagdad is located in west-central Arizona in Yavapai County. Ransome' divided the State of Arizona into three provinces: I? the plateau to the northeast; 111, the desert region to the southwest and 11, the moun-

Jan 1, 1949

By W. A. Backofen, B. B. Hundy

THE pole figure interpretation in a recent paper' on the torsion texture of copper was questioned in discussion,2 nd a simpler alternative interpretation was proposed. In the hope of reaching a positive decision in favor of one or the other, further studies were undertaken with 70-30 brass and Armco iron. This additional work has not answered all the questions about torsion textures, but the new pole figures do offer support for the original interpretation and show that the texture is more complicated than the alternative suggests. From the previous paper,' the appropriate method of describing the texture in a twisted bar is known to be a pole figure plotted on a plane tangent to the surface of the bar. The axes of the pole figure are chosen to coincide with directions in the tangent plane which are parallel and at right angles to the bar axis (the longitudinal direction, L.D., and the transverse direction, T.D.), for these directions define symmetry axes of the texture. Therefore any ideal orientation that might be selected to represent the texture gives the crystallographic plane parallel to the tangent plane and the crystallographic direction parallel to the axis of the torsion specimen. A unique texture was assumed in the original interpretation, and the four ideal orientations, (112) [111], (111) [112], (110) [001], and (112) [131], were used in its description. Of the four orientations, the first three provide possible slip directions along the direction labeled T.D. in the pole figure, which is one of maximum shear stress in a specimen being twisted. The alternative, however, simply considered the texture to be made up of two components, one a [Ill] alignment along the specimen axis with a random orientation about the axis as in the wire texture, and the other a superimposed orientation (110) [0011. Experimental evidence for this simpler interpretation was derived from two observations: 1—twisting did not alter the orientation of a single-crystal torsion specimen of a brass in which an octahedral plane was perpendicular (and a [Ill] direction parallel) to the axis, and 2—deformation bands with approximately the (110) [001] orientation were seen to develop in the crystal during the test. The new pole figures were obtained with a brass and an iron torsion specimen of 3/4 and 1 in. gage length diameter, respectively. After annealing, polishing, and twisting, seven rods, about 0.030 in. in diameter and with different orientations, were prepared from material near the surface of each specimen; these were required for the method of constructing pole figures by using a Geiger counter as developed by Norton.5 Since the shear strain gradient in plastic torsion is linear, it was readily computed that the material supplying the brass rods had been subjected to a shear strain of about 3.2, and that supplying the iron rods had received a shear strain of about 2. All details concerning specimen design, testing procedure, rod preparation, and use of the Norton technique can be found in ref. 1. Only this procedure was followed in working out the (111) and (100) pole figures for brass, Figs. 1 and 2. However, X-ray photograms were also involved in the construction of the (110) pole figure for Armco iron, Fig. 3. The photograms were made according to the conventional transmission diffraction technique using a small sheet taken parallel to the specimen surface and etched to a thickness of about 0.0025 in. They were especially important in locating the boundaries

Jan 1, 1954

By Charles H. Sawyer, Walter Knox

All of the coals commonly used in domestic bituminous stokers form coke, and satisfactory operation depends upon the fact that the coke formed is so weakly bound together that it breaks readily in the normal operation of the stoker and automatically maintains a good fuel bed. Some coals, because of their tendency to form solid, blocky coke, are practically excluded from use in small domestic stokers as now built. Other coals, some among the best stoker coals available, can form this troublesome coke under certain conditions. Many contradictory methods have been offered as cures for coke formation. Generally the procedure has been to try various adjustments until a combination was found that seemed to give better results. Such random methods of treatment have not provided any reliable information as to causes. The present paper covers a comprehensive test program undertaken by the Koppers Company's Stoker Coal Research Laboratory at Kearny, N. J. The program had two main objectives; first, to discover what factors affected coke formation, and second; to define corrective steps that could be applied in stoker service work. Conclusions and Results i. The design of the stoker outweighs in importance all other factors capable of improving coke formation. 2. Insufficient air supply aggravates the formation of large blocky coke, although raising the air above 30 to 40 per cent excess (as determined during steady running) does not further improve the character of the coke formed and only reduces its accumulation at the expense of efficiency, increased fly ash, poorer clinker-ing, and other disadvantages. 3. Increasing the coal feed results in a somewhat more friable coke structure and is recommended for persistently troublesome jobs. 4. Increasing over-fire draft improves the character of the coke formed and reduces troublesome accumulations by accelerating off-period burning, although at some expense in efficiency and some increase in fly-ash accumulation. 5. Coke structure was not substantially improved by blocking some of 'the retort tuyeres, although the blocking of tuyeres at the feed-screw end of a rectangular retort did lead to somewhat improved performance, possibly because of considerably better distribution of coke in the fuel bed. 6. With the equipment tested no difference was shown between installation of the same stoker in a steam boiler and a warm-air furnace, or between a sand-filled and a ventilated type of hearth. 7. The following design features had no noticeable effect on coke formation: a. Presence or absence of coal-tube air as provided by many manufacturers to eliminate smoke-back. B. Presence or absence of a flap damper ill the air duct to minimize off-period burning. c. Continuous or intermittent (ratchet and pawl driven) movement of fuel feed screw.

Jan 1, 1944

By Shiou-Chuan Sun

THERE are several postulations for the mechanism of slime-coating. Ince1 proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube, after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4: 1 and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,4 several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.[4a] per liter of water, should not be

Jan 1, 1943

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 ¾ million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done3 on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the light-weight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By G. J. Benard

In the 1970’s, several plants have been built and others are in the design stage which use solvent extraction for recovery of copper from acid leach solutions. Other plants are presently being built for the recovery of nickel and cobalt from laterite ores by prereduction and ammonia leaching. A review will be given on the materials of construction for these leaching and solvent extraction processes. Many plants have factors in common which permit selection with a greater degree of accuracy. Based on pilot plant corrosion data, effective use of materials of construction includes proper selection of materials, substitution of lower cost plastics for alloys, and selection of materials resistant against chloride stress corrosion cracking.

Jan 1, 1974

By W. D. Steele, S. D. Brady

The Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains minable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon-galia Co. thence south and southwest across the state to Wayne Co. near Hunt-ington. The Pittsburgh coal is also minable in the Upper Potomac region but is now practically exhausted there. The total minable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13¼ billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio River as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern West Virginia District comprising Wetzel, Mon-ongalia, Marion, Preston, Harrison, Dodd-ridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 1880 (when the Monongahela River Railroad, now B. & 0. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgan-town and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Mononga-hela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of minable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. Economic Importance The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1949

By Donald L. Katz

The compressing of gas into a partially depleted gas drive oil reservoir to bring the contents to a single phase miscible with gas is proposed as a process worthy of serious study. The compressed gas and vaporized oil would be recovered by cycling. This paper explores the Possibility of recovering oil from reservoirs of 6,000 ft or more by this method. INTRODUCTION Many new methods for increasing the recovery of oil from reservoirs are under consideration in the various research laboratories. One method which should be considered for recovering oil From partially depleted gas drive fields is to compress gas into the reservoir until the contents become a single phase miscible with more gas. Natural gas then may be cycled through the reservoir to recover the oil. This procedure ideally will eliminate the capillary effects of the liquid ill the porous media and should permit recoveries similar to those obtained in cycling operations, probably of the order of 80 per cent. This paper explores the information now available for the prediction of the performance of such a project and discusses the problems likely to be encountered in recovering oil by cycling. For many years dry natural gas has been passed through oil reservoirs to recover natural gasoline which would vaporize from the oil. Recently a process of recovering more of the high boiling hydrocarbons has been described by employing high pressures at which the heavier hydrocarbons have a higher volatility. Nevertheless. this reported method does not eliminate the differential nature of the vaporization process and capillary forces are still present in the reservoir. The process under discussion in this paper would minimize differential vaporization and would remove capillary forces which are responsible for low oil recoveries. Higher gas pressures are required to accomplish this removal of the miniscus, but it does not follow that more gas is required for oil recovery. The process is limited to reservoirs deep enough to permit the use of the required pressure — Probabably 6,000 it and deeper. DESCRIPTION OF THE PROCESS Briefly, the process is to compress natural gas into an oil reservoir which is partially depleted so that it has an oil saturation in the range of 40 to 60 per cent of the hydrocarbon pore space. The injected gas will pass through the channels formerly carrying gas to the wells to build up the pressure and dissolve in the oil phase. This injection will continue without production from the field until the reservoir reaches a single phase. If one were to select unique conditions such that the gas composition, the reservoir oil composition and the Per cent saturation would bring the mixture in the reservoir to the critical temperature and pressure simultaneously the phase behavior accompanying injection is shown by Fig. 1. The oil-gas mixture in the depleted reservoir has a critical temperature at C,. Addition of natural gas to the mixture will give a new critical temperature for each addition. Mixture No. 3 is shown to have its critical temperature at the reservoir temperature and reservoir pressure at P: the critical pressure. Under ideal behavior, the entire reservoir would be at iti critical temperature and pressure and the entire hydrocarbon content would be at a single phase. If the reservoir content were a binary system of methane and a heavy constituent. it would be miscible with more methane. However, for complex mixtures the critical locus does not confine the two phase region, and the dew point curves of Fig. 1 occur above the critical locus. If fluid which was injected into the rezervoir at the critical point were of the

Jan 1, 1952

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By J. T. Peters, N. Schapiro, R. J. Gray

Petrographic studies of coal have resulted in a better understanding of the origin and composition of coal and have added to the knowledge of how and why coals differ in their response to various prepamtion and utilization processes. Petrographic methods can now be used in scientific economic exploitation of coals. Because the United States Steel Corp. is one of the largest consumers of coal and coke, there is a continuing interest in the corporation in perfecting a better understanding of coal so that it can be utilized more effectively. Coal is a heterogeneous substance composed principally of plant material that has been altered by a complex geochemical process to form rock. The science of coal is anthracology. The ultimate aim of anthracology is determining the relationships and differences among coals. The fundamental aim is finding out why coals differ. The practical application is determining how the differences in coals affect their utilization properties. Coal, like other sedimentary rocks, consists of more than one material. Fig. 1, a photograph of a natural fracture and a polished surface of a lump of coal, displays heterogeneity in terms of the banded ingredients present. The earliest attempts to describe coal were based on its hardness and appearance. ' Thus, coal has been described as hard or soft, bright or dull, and banded or nonbanded. The variations in the hardness and physical appearance of the coal reflect differences in materials that constitute the coal. The banded nature, lustre, and texture depend upon the relative proportions of the various constituent materials. Even the earliest petrographic investigations of coal produced evidence of of the heterogeneity of the coal substance and shoul have destroyed the concept of the unit coal molecule. Coals (Fig. 2) that appear the same frequently consist of different microscopic materials and may behave differently during mining, pulverization, washing, or coking. In Fig. 3, the upper photograph shows a bright at-trital medium-volatile coal, and the micrograph at the right shows some of the materials that constitute the coal. The lower photograph shows a bright attrital low-volatile coal and the corresponding micrograph shows material of similar origin to those from the medium-volatile coal. Any petrographic description of a coal that has meaning in terms of its utilization begins with a microscopic examination. Numerous attempts have been made to describe coal on the basis of the materials that constitute the coal.2*3 Initial petrographic studies were directed towards the question of the origin of coals without any true basis for studying the metamorphic changes in the

Jan 1, 1962

By Milton E. Wadsworth

The reduction of a metal in an aqueous solution may be defined in terms of its source of electrons. In electrolytic reduction electrons flow as a result of applied voltages. In other systems electron sources are reducing gases or metals of lower electron affinity. In the latter two cases it is increasingly evident that reduction is electro-chemical in nature in that electrons flow through one or more conducting phases even though the discharge reactions may not be rate controlling. Electrode processes impmtant in reduction and metal deposition are reviewed and extended to contact reduction by precipitation (cementation) on mme electropositive metals. Contact reduc- tion Processes are ancient in origin and represent techniques which have had successful application for hundreds of years. In spite of this, little has been understood in terms of the dynamic properties of such systems or of important side reactions. In recent years an increasing amount of laboratory work has been carried out on contact reduction and an attempt is made here to summarize the important findings. Undoubtedly the interest aroused recently may be attributed to improved reactor design which has demonstrated on a commercial basis accelerated metal recovery by taking advantage of important kinetic and chemical parameters. of gold cyanide (Au(CN)-), respectively. The most common method for the reduction of ions in solution is by electrolysis. The impure metal is made the anode and the ions are reduced at the cathode. Leach liquors containing reducible ions may similarly be reduced electrolytically using an inert anode. The latter process is referred to as electrowinning. In recent years hydrogen has been used successfully as a gaseous re-Metallurgical Society of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). He was also a member of the Executive Board of the Metallurgical Society (AIME). In 1957 Dr. WADSWORTH was given the AlME Best Paper Award as coauthor of a paper on the roasting of sphalerite. On July 1, 1968 Dr. WADS-WORTH started an 24 month assignment in the Philippine Islands to assist in the development of graduate metallurgical engineering at the University of the Philippines. In addition to graduate teaching and curriculum development he will establish research programs to develop extraction processes for metals production in the islands. The project is supported by the Ford Foundation through Educational Projects, Incorporated.

Jan 1, 1970

By M. B. Bever, A. B. Michael

THE structure of cast A1-Si alloys is altered profoundly by modifying agents. Sodium, in particular, reduces the size of the silicon particles in the eutectic and tends to change their shapes from plates to nearly rounded grains. This refinement is accompanied by a shift of the eutectic to higher silicon concentrations and lower temperatures. Similar effects can be attained by rapid solidification. Hypotheses advanced to explain modification have involved the formation of a ternary eutectic,1 the removal of oxides by fluxing,' and even a presumed allotropic transformation of silicon. Other hypotheses assume that the modifying agent causes an envelopment of the silicon particles by the aluminum-rich solid solution, but attribute this envelopment to different mechanisms. According to various explanations, the growth of the silicon particles is obstructed by an immiscible sodium-rich liquid," an adsorbed layer of sodium,' or a ternary compound;5 his obstruction has been conceived as purely mechanical or as a colloidal action.' It has also been proposed that sodium reduces the surface tension on the Al-Si interface, thus permitting the aluminum-rich solid to grow faster and to envelop the silicon particles.? Still other hypotheses stress undercooling and the attendant change in the rate of nucleation of silicon, but fail to ascribe any definite function to the sodium addition." '" Procedure High-purity alloys of aluminum and 3 or 7 pct Si were treated with modifying agents containing radioactive sodium tracers. The experiments were intended to investigate the partition of sodium between the primary aluminum-rich solution and the eutectic, and, if possible, to determine whether sodium is concentrated in or around the silicon particles in the eutectic. Radioactive sodium fluoride, alone or mixed with stable sodium chloride, was allowed to react with the alloy for 5 min immediately before solidification in the crucible. Modification could not be attained with additions of less than the equivalent of approximately 0.1 pct Na. Some alloys were not completely modified, but comparison of the structures of treated and untreated specimens indicated a very considerable reduction in particle size of the silicon in all of the former. A treated alloy is shown in Fig. 1. Radioactive sodium fluoride was prepared by bombardment with deuterons having an energy of 14 mev. This bombardment (totaling, for example, 6 microampere-hours in one run) produced radioactive Na24 (half-life 14.8 hr) by the reaction 11Na23 (d,p) 11Na24. The radioisotopes of fluorine also produced have short half-lives and were not detected. A half-life determination by counting confirmed that the measured activity was due to Na24. The distribution of the sodium in the solidified alloys was determined by an autoradiographic technique by which a suitable stripping film is attached to a very thin metallographic specimen. After exposure and development, this emulsion remains superimposed on the specimen and may be examined microscopically or photographed by reflected light. The emulsion of the autoradiograph can be correlated directly with the underlying surface by simple adjustment in focus. The details of this technique have been described elsewhere." Results Fig. 2 is a micrograph of the autoradiographic emulsion ("autoradiograph") lying directly above the area of eutectic in Fig. 1. Fig. 3 shows a similar autoradiograph of a region consisting of primary solid solution. The small black dots (tracks) in these autoradiographs are developed grains in the emul-

Jan 1, 1954

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By G. Sachs, G. Espey

It is well known that high residual stresses are created in tubing by the sinking process, in which no internal tool or mandrel is used.l-4 In this process, the wall thickness is usually slightly increased.4,5 In tube drawing with a plug, the residual stresses are gradually reduced with increasing reduction of wall, and, by the conventional approximation methods of stress measurement, no stress is detected in tubing in which the wall reduction is over 50 per cent of the total reduction in cross-sectional area.l,6 It has also been observed that higher stresses are set up by the use of wide-angle dies than by acute dies.? 'he actual stress distribution in drawn tubing has been investigated by a few workers,7"9 but has not been related to the conditions of the drawing process. Some attempts have been made to correlate accelerated cracking tests for stresses in brass products with the magnitude of the circumferential stresses and the condition of the metal. l-10 Materials and Preparation The material used in this experiment was commercial cartridge-brass (70 per cent Cu, 30 per cent Zn) tubing in the straightened and annealed condition.† This tubing was of various outside diameters and had a wall thickness of 0.032 in. It was sunk to 1/2-in. outside diameter by means of an experimental 10,000-lb. hydraulic draw-bench, with a maximum drawing speed of 8 ft. per minute. All dies were of 1/2-in. diameter. Various die materials and contours were used in order to study the effect of die design on residual stresses in the tubing; the specifications for the dies are given in Fig. I. Castor oil was used throughout as lubricant. Chattering occurred in sinking some of the tubing, particularly when dies having the more acute angles were used, but the tubes showing chatter marks did not differ markedly from those with a smooth surface regarding the magnitude of residual stress. The source of the chattering has not yet been revealed. The wall of the tubing becomes thicker during s nking, as previously observed.4,5 The increases in wall thickness were 3, 7 and 9.5 per cent on the average for 6, 20 and 33 per cent reductions in diameter, no effect of the contour being noticeable. The reductions mentioned throughout this investigation do not consider this fact, but are reductions of the outside diameter. For the evaluation of the residual stress two fundamentally different methods were used. The approximation methodl,ll of splitting a certain length of tubing was employed to obtain a bird's-eye view of the effect of various drawing conditions on the circumferential stress measured by the diameter change occurring On splitting. For

Jan 1, 1942