Search Documents

By Leland L. Mink, Roy E. Williams, C. Daniel Kealy

The passage by Congress of Public Law 92-500 (the 1972 Water Pollution Control Act amendment) has placed a new emphasis on the need for methods to minimize the escape of water from tailings ponds. Presumably tailings pond seepage will fall under the jurisdiction of the act. This paper is designed to explain some of the problems caused by leakage from tailings ponds and to present a method by which leakage can be minimized if not eliminated. Ground-water pollution in one case studied by the authors results from leaching of old jig tailings that are intermixed with the upper part of a sand and gravel aquifer. Anomalous concentrations of zinc, lead, and cadmium occur in ground water and soil samples taken from the portion of the sand and gravel aquifer containing the old jig tailings. Analysis of water samples from a tailings pond located in the area indicates that the pond water is not the source of the heavy metal concentrations found in the down-gradient ground water. However, leakage from the pond and water from the pond's decant system combine with natural ground water to compound the problem by raising the water table into old jig tailings which cover the upper portion of the aquifer. The ground water which discharges from this aquifer causes a statistically significant decrease in the quality of the receiving stream water. The shallow ground water contains oxygen; therefore, corrective measures include lowering the water table to depths below the old jig tailings which cover the aquifer at ground level. This, in turn, implies elimination of ground-water recharge by subsurface leakage from the pond. A laboratory study and a mathematical model study have revealed that seepage from such ponds can be minimized by a carefully designed and managed peripheral tailings discharge system. The process involves maintaining the slime zone and the free-water surface near the center of the pond so that the slimes retard downward and semilateral movement of pond water. The free-water surface must not be allowed to extend out over the nonslime portion of the tailings during or after pond operation. Mathematical model output reveals that this method can hold the subsurface discharge rate to as little as 110 gpd per acre of pond water area. The technique should be applicable to any tailings pond system in which the loss via seepage of poor quality water must be minimized or where recharge of ground water by losses from a tailings pond must be minimized, regardless of the reason.

Jan 1, 1974

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952

By G. M. Wiles

The increasing number of problems of the modem mine manager has led the author to discuss the art of management. He lists the principles concerning selection of personnel, exploitation and development, new equipment, process improvements, new processes, maintenance, operating cost data and public relations. Application of the principles to problems of mine startup, operation and rehabilitation are described. Since D. C. Jackling was famous for his adeptness at organizing and training teams of operating personnel, the subject of mine management is particularly appropriate for a Jackling Lecture. In fact, it is doubly appropriate because in very basic ways Jackling's career changed the nature of the tasks and challenges facing a mine manager. Management of mines, of course, is the art of finding and winning minerals economically from the earth's crust, and it involves the use of all the engineering sciences. But also of prime importance is a skill which is not yet a science - the area of management often referred to as human engineering. Since expenditures on staff and labor may well involve more than 50% of the direct costs of operating a mine, ability at human engineering is just as important as the ability to plan and put into effect the most efficient operating procedures. In addition to his ability to select and train operating personnel, Jackling possessed, to a degree unmatched by many of his contemporaries, broad, analytical powers covering both the economics and operating phases of large scale mineral extraction. His breadth of vision found its greatest expression at the time he analyzed the Utah copper deposit. Fortunately, Messrs. Penrose and Gemmell had enough faith in his analyses to furnish the capital needed to begin operations. The result, as is well known to all of you, was Kennecott's lucrative Utah copper mine — and the beginning of the open pit porphyry copper era. The Utah copper mine, and Jackling's subsequent similar successes in Arizona, New Mexico and Nevada, had one thing in common —all of these large porphyry deposits were worthless until open pit, large daily tonnage schemes were developed for their exploitation. The successful development of such schemes made vast new mineral resources available for economic exploitation. But at the same time, the trend away from smaller high grade operations in favor of the far more complicated operations required to handle large deposits of low grade ore have greatly altered a mine manager's problems. We are all familiar with the saying "mines make managers." There is still some truth in this statement, but far less than there used to be in the days when high grade properties were the rule rather than the exception. When high grade orebodies prevailed, many managers, superficially at least, could not make a mistake because the profits of their mines

Jan 1, 1962

By P. H. Dudley

I have taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of 'our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that,, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its econonlical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 941/2 miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 footpounds, exclusive of the force to move the locomotive itself. We

By Portland P. Fox, Berlin C. Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. THE EQUIPMENT The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1938

By John. C. Reed

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62° W. The average dip is about 67° SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30° W. and average dips about 75° SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30° for the south-west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By H. M. Chance, T. M. Chance

The term 'Llow-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as.1 1/2 per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. , In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low-sul. fur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, with few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 1/2 per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous districts, it has been necessary to turn to the areas of higher sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.—Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout the coal but is usually confined to high-sulfur benches in the bed or to concentrations on the cleavage planes of the coal. Hence, by graded crushing and sizing it is frequently possible to at once reclaim those portions of the coal bed containing coal that is relatively free from pyrite.

Jan 1, 1920

By J. A. Collins, C. H. Mathewson

The process of plastic extension of face-centered cubic single crystalline rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellar arc free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [121] direction in the axis of the rod. This process has been checked in malty face.-centered cubie materialsand and readily permits the preparation of specimens that have been subjtvted to various determinable amounts of shearing action. It is elearly of interest to study in such measurably strained speeimens the, development of a recrystallized structure on annealing and if possilble detect the source of nuclei from which the new crystals grow. Strain-:~nneali~ig experiments of this charactcr have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs. the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae at the conclusion of a test of from 0.08 to 0.57. A particular point wa-made of determining the crystallite rotation, or small angular range. assumed by the octahedral slip plane after these various amounts of shear. The, mechanism of reerystallization and the magnitude and effeet of recovery on the recrystallization process was investigated.

Jan 1, 1940

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large. Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton acid Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, 111. All three have water conditions that make it necessary to regularly seal off till worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will he included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By John Chipman

IT has been long known that the gas evolved during the boil in the open-hearth furnace is mainly carbon monoxide associated with smaller quantities of other gases. A number of attempts have been made to determine the precise effects of carbon and oxygen content of the bath, and of other factors, such as temperature, upon the evolution of carbon monoxide. In his investigation of the carbon-iron oxide product in liquid steel, Herty1 showed that the value of this product at equilibrium could be approximated by plotting the value of the product observed in open-hearth reactions against rate of carbon elimination, and extrapolating to zero rate. The results of this study showed a slight but definite effect of temperature upon the carbon-iron oxide reaction. Experimental studies of the evolution of gases from rimming-steel ingots have not yet attained the degree of precision necessary for an exact understanding of the effects of pouring temperature, carbon content, and iron oxide in the metal upon the composition of these gases. Klinger2 showed that the gas consists mainly of carbon monoxide, and that con-siderable variation in its composition occurs during the solidification of the ingot. In order that these variations may be understood in their proper relationship to the progress of solidification of the ingot and the segrega-tion that accompanies solidification, it is essential to have a knowledge of the condition of equilibrium in the several chemical reactions by which the gases are being formed. It is also necessary to understand the effects of temperature upon the equilibria, and further, to know the manner in which the temperature of the liquid metal within the ingot changes as the skin of the ingot is being built up. The reactions in which we will be chiefly interested are those involving in the one case the oxides of carbon, and in the other case steam and hydrogen, with iron oxide and carbon in the liquid metal. The reactions as they occur in unalloyed liquid iron, and their respective equilibrium constants are written as follows:

Jan 1, 1937

By T. N. McVay, E. E. Creitz

Rather large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about I. miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and ti-tanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, Opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The x ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fe+2 and Fe+3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1949

By Henry H. Angst

Tim history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 1/2-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu, yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By Eric S. Cheney

Sulfur isotopes are best used in conjunction with other geological studies to determine the origin of known deposits; concept-oriented exploration programs can then be developed to find similar deposits. Geochemical processes are capable of causing different S '41S" ratios in the minerals and fluids participating in natural reactions. Because the magnitude of the resultant isotopic difference is inversely proportional to temperature, sulfur isotopic studies can be used to determine the source of the sulfur in high temperature deposits. The narrow spread of sulfur isotopic values from ores related to cupolas of felsic intrusions suggests that the sulfur in the ore-forming fluids was derived from a fairly uniform source (such as the intrusions) rather than by heated ground water from the adjacent country rocks. However, geologic and isotopic evidence suggest that the sulfur of many nickel sulfide ores may have been derived from the country rocks rather than the associated mafic igneous rocks. This sulfurization hypothesis implies that mafic intrusions in sulfur-rich country rocks should be prime exploration targets. Sulfur isotopic analyses of sulfides in the mafic rocks may indicate whether sulfurization has occurred. In equilibrium geochemical reactions S" is concentrated in the minerals with the greater bonding strengths. Thus the isotopic compositions of coprecipitated sulfides that have not undergone exsolution may be used as geothermometers and to distinguish multiple periods of mineralization, post-ore metamorphism, etc. The sulfur isotopic compositions of coexisting sulfides at Butte, Mont., indicate that the copper minerals did not originate by simple replacement of pyrite. Geologic and isotopic evidence suggest that the mineralogical and isotopic zoning at Butte formed almost isothermally during the geochemical evolution of the ore-forming fluids upward and outward from the Central zone. Unidirectional reactions cause enrichment of S" in the products. At low temperatures the isotopic effects of bacterial and inorganic reactions are difficult to distinguish. Anaerobic sulfate-reducing bacteria apparently were responsible for the sulfur of Gulf Coast salt domes and for diagenetic pyrite in sandstone-type uranium deposits. Sulfur (and carbon) isotopic data suggest that the roll ore bodies of sandstone-type uranium deposits originated by limited inorganic oxidation of diagenetic pyrite rather than by bacterial activity. Accordingly roll ore bodies should be most numerous and thickest against those portions of the sandstone aquifer that contain pre-ore pyrite.

Jan 1, 1975

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By Frank Foote, Eric R. Jette

In a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be considered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe3O4 instead of the original Fe4O4. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously determined fact that the FeO lattice is ionic (i, e., consists of Fe++ and O? ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1. The purpose of the present investigation was to determine the limits of this homogeneity range by means of the X-ray structure analysis. This method has been applied frequently to the study of solid solutions by Westgren and his coworkers as well as by other investigators. The principle is simple: if the change in lattice constant with composition is

Jan 1, 1933

By Nelson B. Russell, Donald C. Bond

The effects of various antifreeze agents on the formation of hydrogen sulphide hydrate have been studied. On a molar basis the relative lowering of Tm (the maximum temperature at which solid hydrogen sulphide hydrate can exist in equilibrium with the given solution) for the various agents is: sodium chloride 1.00, calcium chloride 1.71, methyl alcohol 0.57, ethyl alcohol 0.68, ethylene glycol 0.73, diethylene glycol 0.73, sucrose 0.87, dextrose 0.71. On a weight basis the relative lowering of TM is: sodium chloride 1.00, calcium chloride 0.91, methyl alcohol 1.08, ethyl alcohol 0.89, ethylene glycol 0.69, diethylene glycol 0.41, dextrose 0.23, and sucrose 0.15. Introduction The solid hydrate of hydrogen sulphide, H2S.6H20,1 is in equilibrium with water and liquid hydrogen sulphide at 85°F at a partial pressure of hydrogen sulphide approximately equal to the vapor pressure Of hydrogen sulphide at that temperature. At temperatures below 85°F, in the presence Of excess hydrogen sulphide (greater than the amount required to react with the water present) the hydrate is in equilibrium with liquid hydrogen sulphide at approximately the vapor pressure Of hydrogen sulphide. In the presence of excess water, the solid hydrate is in equilibrium with liquid water, containing dissolved hydrogen sulphide, at a pressure lower than the vapor pressure of liquid hydrogen sulphide at the same temperat~re.2 The lower the temperature, the greater the difference between the decomposition pressure of the hydrate and the vapor pressure of liquid hydrogen sulphide at that temperature. Conditions conducive to the formation of solid hydrogen sulphide hydrate may exist in wells producing a gas containing a high percentage of hydrogen sulphide under high pressure, or in the lead lines from such wells. This paper gives the results of tests made with various antifreeze agents which might be useful in decomposing the hydrate or in preventing the formation of the hydrate of hydrogen sulphide Apparatus Fig , shows a diagram of the apparatus used. The sample under observation was contained in a glass tube 34 cm long, having a 6 mm id and a wall thickness of 2.5 mm. The lower end of this tube was closed- with a plug of butyl rubber. The upper end of the tube was connected to a diaphragm gauge, with a stainless steel diaphragm, a manometer, a vacuum pump, and a cylinder of hydrogen sulphide, The tube was held nearly horizontal, with the liquid resting along the lower side of the tube. It was found that when the tube was held in a vertical position, it broke with ex. plosive violence as soon as it became filled with solid hydrate. Presumably this was caused by the expansion which occurred on solidification of the hydrate. The difficulty disappeared when the tube was held in an inclined position during the tests.

Jan 1, 1949

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By L. L. McMurray

Ilmenite is the most important raw material for manufacture of titanium dioxide.' Industrially, several other products are made from ilmenite, the most important of which are: ferro titanium, ferro carbon-titanium, copper-titanium, titanium carbide and titanium nitride. The production of titanium metal is still in the laboratory stage because of the difficulty of extraction and as yet no important application for the metal has been found. Ilmenite has received considerable attention as an industrial raw material. Imports of ilmenite concentrates for the first nine months of 1941 were 156,737 short tons, the chief source being Travancore, India.2 Domestic produttion of ilmenite has heretofore been confined to Amherst and Nelson Counties, Virginia, where a complex rutile, ilmenite, and apatite ore is mined and treated to utilize all three of these minerals. A recent report3 has described development of the large titaniferous magnetite ore body at Tahawas, New York, where it is expected that 800 tons of ilmenite concentrates, containing 48 per cent TiO2 will be produced daily. Additional domestic production is expected from a large ilmenite deposit recently opened in caldwell county, North carolina. Flotation tests indicate that a high-grade concentrate containing 53 per cent TiO2 can be made from the North Carolina ore. Prospecting of domestic ores in other areas has been reported.' It appears that increased domestic production of ilmenite may well save considerable shipping space so vitally needed in these times. The composition and chemical structure of pure ilmenite is given by Dana as: FeO, TiO2; Ti, 31.6 per cent, Fe, 36.8 per cent, O2, 31.6 per cent. This composition is variable in that some iron or titanium may be replaced, giving a variable iron-titanium ratio. As an example, the iron-titanium weight ratio of ilmenite in Caldwell County, North Carolina, has been determined to be 0.94 (using 97.1 per cent ilmenite concentrate obtained by heavy liquids on minus Iso-mesh ore) compared with theoretical 1.16. No rutile was noted in this ore to account for the low value. This North Carolina ore is free of magnetite, which is a common associate of ilmenite ores. In view of a large potential production from North Carolina, the Tennessee Valley Authority conducted a study of methods of concentration of that ore, of which the results are reported herein. The Ore Five samples of Ore were taken from the deposit at various exposed locations and were mixed for the study and testing. An attempt was made to proportion the amount of weathered and unweathered portions in making the composite sample, so as to approximate actual operating conditions. An examination of representative specimens of the sample showed the following general facts: 1. The black mineral comprising nearly 70 per cent of the ore is ilmenite.

Jan 1, 1948

By E. T. Wessel

UNEXPECTED brittle failures of metals in practical applications are a serious problem to many industries and to the nation as a whole. Considerable effort has been devoted to studies of the brittle behavior in metals. However, the major portion of this effort has been directed at developing techniques and apparatus for the purposes of determining the susceptibility of metals to brittle failure and of making various types of observations of the phenomena. Relatively minor effort has been made to understand the basic mechanisms involved in initiating brittle failures. A more complete understanding of the nature and mechanism of the brittle failure problem would be very helpful in efforts directed toward predicting and avoiding brittle failure and toward the development of suitable materials and designs that are not susceptible to a brittle behavior. The intent of the present investigation is to acquire this basic understanding. The pronounced transition from a ductile-to-brittle behavior is most prevalent in metals having the body-centered-cubic lattice structure, primarily be- cause metals of this structure exhibit a strong dependence of yield strength upon temperature and the rate of straining. The generally recognized qualitative concept of the ductile-to-brittle transition is that brittle (cleavage) failure occurs when the yield strength exceeds the cleavage fracture strength. This condition can apparently be achieved by decreasing temperature or increasing strain rate. Likewise, a normally ductile metal can be made to fracture in an apparently brittle manner by the introduction of triaxial stresses (notches) where the ratio of normal to shear stresses can be increased to such an extent that the normal stress exceeds the fracture strength before the critical shear stress for plastic flow is achieved. Neither of these concepts require any prior plastic deformation or explain why the observed fracture strengths are so much less than the theoretical cohesive strength. The results of several investigations of the ductile-to-brittle transition in body-centered-cubic metals illustrate rather conclusively that measurable amounts of nonelastic deformation do precede cleavage fracture, even at extremely low temperatures. These studies suggested that the early stages of plastic flow, particularly abrupt yielding, and their relationship to brittle fracture should be examined

Jan 1, 1958

By O. P. Chisholm

The most noticeable change in lead smelting over the past few years has been the increase in the smelting rate of lead blast furnaces. For several years a great deal of attention has been paid to the preparation of the blast-furnace sinter charge but more recently the plan has been to incorporate- almost the entire makeup of the blast-furnace charge, excepting coke and scrap iron, at the sintering machines. Formerly, sintering machines were used primarily for removing, sulphur and for agglomerating finely divided material both sulphide and oxide in character. Limestone flux usually was so proportioned that a relatively large amount was added to the furnace charge direct. This procedure was also followed with oxidized ores, which were purposely crushed coarse' so that they would be adaptable for direct smelting on the furnace charge. In later years it has been the tendency in western smelters to include practically all of the limestone and oxidized ores in the sinter charge. This has been somewhat more costly because fine crushing is required for sintering purposes and because these oxidized materials were given additional processing through the sinter plant. The addition of such oxidized materials to the usual charge to be sintered, brought about, in certain instances, a deficiency in heat ordinarily supplied by the sulphide constituents of the charge. This heat deficiency has been remedied by the addition of carbonaceous fuel, in the form of finely crushed coke breeze, or in a few instances by the addition of zinc retort-plant residues. The enhanced gold price has stimulated the mining of crude siliceous ores throughout the Western States and in the smelting of such ores more limestone is required for fluxing. Shipments of gold-bearing pyritic concentrates to Western smelters have increased, and the combination of increased silica, limestone and pyrite has increased the percentage of slag, which, in itself, is an aid in .securing smoother and more rapid smelting in the blast furnace. By the addition of these substances, the percentage of zinc in the slag has been appreciably lowered. at many plants, with resultant benefit to smelting speed at the blast furnace. This increase in slag formation with lowered zinc content has caused also perceptible lessening of the amount of lead on the charge and this has benefited the blast-furnace smelting. Although a satisfactory sinter is fundamental in increased rate of bullion production per furnace, there has been a trend over the list four or five years to decrease the percentage of coke and increase the percentage of scrap iron and limestone on the blast-furnace charge. As a result of these changes in practice certain blast furnaces, without any mechanical change, have doubled or tripled their tonnages. For furnaces whore the volume of air is recorded, records show decidedly larger air volumes with a comparatively small increase in air, pressure, or, none at all.

Jan 1, 1941