Search Documents

By Louis Bender

AFTER investigating the work of coal-dust fired reverberatories of the Canadian Copper Co., at Copper Cliff, Ontario, the management of the Washoe Reduction Works decided to experiment with and ascertain the advantages of using coal dust as a fuel in their reverberatories. Consequently, during the month of June, 1914, reverberatory furnace No. 8 was changed in order to use powdered coal as a fuel. The results obtained by this method of firing are gratifying and show a decided saving in cost of smelting as compared to grate firing with lump coal. The furnace, as remodeled; is 124 ft. long by 21 ft. wide, and varies in height from 8 ft. 6 in. at the back end to 5 ft. 7 in. at the skimming end. The general construction of the furnace is similar to that of the other furnaces at this plant. There are no side doors to this furnace, as it was thought that with the present arrangement for feeding no "fettling" or "claying" would be required. The interior of the furnace can be inspected through the burner port holes, after shutting off the burners and giving a few seconds' time for the gases inside the furnace to clear away. The charging is done on either side of the furnace from longitudinal hoppers, extending a distance of 74 ft. from the back end of the furnace. Leading from the hoppers into the furnace are 6-in. pipes, spaced 194 in. apart, through which the charge is intermittently dropped. The charge is kept well above the slag line at all times; in this way the side walls are protected and no fettling is needed on this portion of the furnace. The remainder of the furnace requires fettling. After operating for three months, we found that the bricks were eaten into along each side wall from the skimming door back to the point where the charge had been dropped. The depth of this cutting away was 8 in. close to the front end and gradually tapered to zero at a distance of 50 ft., and was greatest on the side of the furnace having the larger flue connection. Hoppers will be put in for the entire length of furnace, from which fettling material will be dropped, to prevent this cutting.

Jan 1, 1915

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By H. M. Roche

MAGNETITE is the important iron ore of New Jersey although bog ore, limonite and red hematite were mined in sizable quantity early in the state's min-ing history. The deposits of mag-netite are found in the Highland area in the northern part of the state. These ores outcrop a broad belt 20 miles wide, extending in a northeasterly direction from Phil-lipsburg, on the Delaware River, to Greenwood Lake, at the southern boundary of the state of New York, a distance of 60 miles. The area in which the magnetite is found (see map, Fig. 1) contains 1200 square miles and the center of the area is at Dover, 40 miles west of New York City. In the general area are found 18 parallel ranges or lines of ore deposits. These ranges may be re-garded as mineralized zones in which occur orebodies that are rich enough in magnetite to war-rant mining. Usually a number of the orebodies lie one above the other in the same plane, all dipping and pitching in the same direction. Within the ranges, there may be several parallel orebodies of work-able size. The average strike of the orebodies is N.41° 30' E., with an average dip of 55° southeast and an average pitch of 15 ° to the northeast. Orebodies suitable for mining range from 6 to 100 ft. wide, as measured from foot wall to hanging wall. Their heights, as measured on the dip and normal to the long axis of the orebody, vary from 200 to 3,000 ft. The length along the pitch has never been determined by mining, al-though several of the orebodies have been worked to lengths of 10,000 ft. The grade of the ore as mined today varies from 30 to 60 per cent iron, and the gangue min-erals are chiefly silica, alumina, magnesia, lime and phosphorus.

Jan 1, 1937

By M. G. Cheney

THE production record of the Sinclair-Moren pool, in southeast Young County, Texas, demonstrates that under efficient operating methods a single well may obtain normal oil recovery from an area of 100 acres or more. This record is the more surprising in view of relatively adverse reservoir conditions such as lack of water drive, moderate initial reservoir pressures and a consolidated sandstone reservoir with original permeability greatly reduced by processes of lithification. This case history is considered worthy of special study in view of the ever present problem of proper spacing of wells. Cupidity, abetted by the unrestrained law of capture, has in too many instances guided development and production methods without regard for sound economic and engineering principles. Largely as a result of ill advised spacing of wells, many oil fields have brought financial losses instead of deserved profit to those using capital, time and energy in this important business of adequately meeting the petroleum requirements of what is known as our modern civilization. In March 1923, the Sinclair Oil and Gas Co. obtained initial daily production of about 12,000,000 cu. ft. of gas and 1100 bbl. of oil in its first well near the center of a 372-acre lease on the L. P. Moren land, James Rose survey, Abstract 245. This exploratory test was drilled as a geological prospect of average promise, on a plunging anticline with possibly 10 ft. of closure as mapped on the outcropping limestone of upper Canyon (Pennsylvanian) age. In subsurface, the top of the producing res-ervoir is 16 ft. lower in this well than in the highest wells but probably 25 ft. above lowest closing contour. Wells No. 2 and 3 were drilled about 1/4 mile west and southwest near a normal fault with some 30 ft. of downthrow to the southwest. The producing sand was reached at a depth of 2512 ft. and drilled to 2529 ft. in the first well. This sandstone reservoir is of Millsap Lake (middle Strawn, upper Cherokee) age. It was absent in the second and third wells, which were abandoned at the depths of 3725 or more. In April 1925, a fourth well was drilled 600 ft. east and 24 ft. lower for top of sand than No. I. Production of about 100 bbl. daily was reported from 2521 to 2562 after an 80-quart shot. This well was drilled to 4560 ft., plugged back to 2575 and shot again; but was abandoned soon thereafter because of small production.

Jan 1, 1940

By Phillip O. Tyree, Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducing bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the pores of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also expanded reserves in a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore occurrences. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of June 1, 1984, a total of 29.87 million mt (29.4 million long tons) of sulphur had been produced west of the Pecos River. Duval Corporation has produced more than 88 percent of that total.

Jan 1, 1985

I BELIEVE that my work would surely be host a seed without fit and that I would fail in that cause which disposed me to satisfy your request to write and form this work [75] if while laboring on it I did not tell you of the art of casting, since it is a necessary means to very many ends. I realize even more that I must tell as much as seems necessary since I have already demonstrated the methods of recognizing the natures and locations of the metals, of smelting and reducing them to their ultimate perfection, and finally have taught you to make their associations and alloys. It is especially necessary since this art and work is not well known, so that no one can practice it who is not, so to speak, born to it, or who does not have much talent and good judgment. For this reason and also because it is closely related to sculpture, whose arms are the support of its life, it is very highly esteemed. In order to describe the whole art in every part, I say that the greatest labors of both mind and body are required for its operations in the beginning, middle, and end. It is indeed true that these labors are endured with pleasure because they are associated with a certain expectation of novelty, produced by the greatness of art and awaited with desire, particularly since the artificer sees that it is an art pleasing and delightful even to ignorant men. As a result, as if ensnared, he is often unable to leave the place of work. To conclude: The outcome of this art is dependent upon and subject to many operations which, if they are not all carried out with great care and diligence and well observed throughout, convert the whole into nothing, and the result becomes like its name [cast away]. Therefore, having considered this work many times, with its extraordinary obstacles and the bodily labors heavy as a stevedore's, instead of exalting it with praise, I wish to say that it is such that a man of noble birth, even though he be gifted or be drawn to it by pleasure, should not practice it and could not unless he is accustomed to the sweat and many discomforts which it brings. He must suffer the great natural heats of summer as well as those excessive and continuous ones from the enormous

Jan 1, 1942

J. M. HARTMAN, Philadelphia, Pa.: Mr. Fackenthal can remember some queer things that occurred at Durham, Pa., Aug. 3, 1876, while he was superintendent. The furnace was working stiff, i.e., blast-pressure 10 to 11 pounds, which was high pressure for those days. With this pressure there was some circulation through the stock. At 9 p.m., flushed cinder. After flushing, air was thrown off' for a moment to " bot up "; the keeper turned the lever and threw on air just as the scaffold dropped, which eased up the pressure to 4¼ pounds. The air-receiver is twice as large at Durham as at other places. The air from this receiver, added to the two seven-foot blowers, gave an extra large volume, which, rushing into the furnace, fired the finely-divided carbon, causing an explosion that threw part of the stock in the furnace out into the open air, threw up the bell-and-hopper with the tunnel-head plates, and gave off' a large volume of carbondust. The bell-and-hopper going up first, the stock followed, and, striking the bell-and-hopper, was deflected in a shower over the cast-house roof, breaking the slates. Sitting at the corner of the engine-house at the time, the stock pelted me, when I ran around the corner to get rid of it. Remembering there were two men at the furnace-top, I shut down the engines, and, running to the top, found them sitting in the hoist-house enjoying the fire-works. The explanation of this explosion is simple. There is in the blast-furnace a bed of fuel extending up, say, 16 to 18 feet above the tuyeres; in this bed of fuel some stray pieces of limestone are found, and a few pieces of unreduced ore; but, generally speaking, it is all fuel. On this bed of fuel is the zone of fusion. In this zone the descending stock is liquefied, except the fuel; the iron, melting, drops out of the ore, and the gangue unites with lime, forming cinder. The iron falls in the form of shot, and, with the cinder, trickles

Jan 1, 1899

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm). Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

By F. Julius Fohs

Centrally located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis, because it and others of its immediate group exhibit the conditions characteristic of all. I. The Memphis MiNe. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of .the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of about 850 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the hills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen. A line of .crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar—some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to the leaching of limestone and calcite, and the minute ones to the leaching of zinc-hlende.

Jan 1, 1910

By William B. Phillips

It is proposed in this paper to discuss some of the chemical and physical principles involved in the manufacture and use of this important by-product obtained in the manufacture of steel by the basic process. The name, " phosphate slag," is adopted as a sort of compromise between "Thomas slag" and "tetrabasic phosphate." By the first of these latter names, viz., " Thomas slag," it is known in Germany, Austria, France, and the other continental countries, and in England, and is more easily apprehended by those who have no special Knowledge of chemistry, while the name " tetrabasic phosphate," being descriptive of the nature of the slag, is perhaps the best. It is but seldom that a discovery of such moment to two great industries is to be chronicled in the history of technical science. On the one hand, the manufacture of iron and steel has been greatly benefited, while on the other hand, the effects already noticed, and still to follow, to the agriculturalist, are of scarcely less conseqnence. The great majority of iron ores in the world, perhaps 90 per cent. of then), are now available for the steel manufacturer, while the manufacturer, and more especially the consumer, of artificial manures is relieved from the fear of the exhaustion of the crude phosphates. We have in phosphate slag, therefore, a product of the highest importance to those who make and we steel and fertilizers. Two great industries, which heretofore have had but little in common, are thus brought into close connection with each other, and the results sure to follow, if one may judge from the history of the past ten years, cannot fail to be of great and increasing value. These results may be compared with those which followed the introduction of the cupriferous Spanish pyrites into England for the manufacture of sulphuric acid. The copper extracted greatly reduced the cost of the acid, hence that of artificial manures. Cheap manures meant better farming and cheaper farm products, and these meant better and cheaper living to nearly all classes of society. The amount of fertilizers now manufactured in the United States

Jan 1, 1889

By Charles Wright

AT most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bull-dozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1935

By Joseph Hartshorne

The attention which this process has attracted, especially in Europe, has led me to believe that members of the Institute would be interested in a report of the progress which has been made in the year and a half that has elapsed since my paper on the subject was read at the Colorado Meeting of this Institute. As already described in that paper (Duns., xxvi., 380), this process is a modificatioii of the open-hearth steel manufacture, whether acid or basic, collsistillg essentially in the division of the charge between two furnaces, one of which is charged about two hours earlier than the other, and tapped into the other after the charge in the latter has become fluid, the slag of the first bath being removed from it during the transfer. This description still remains true as far as it goes, but further experience has demonstrated that circumstances will very materially modify the relation of the two furnaces to each other, and the character of the work done in each of them. The function of the primary furnace has become more clearly and entirely that of doing the rough work of desiliconiziug and dephosphorizing, while that of the second or finishing-furnace has become almost entirely that of decarburizing and finighing the heat. To indicate these developments and their results is the object of this paper. In order to avoid needless repetition, I shall try to accomplish part of this object by giving a short resume' of what has been published elsewhere on this subject since my former paper was read. This will at least enable those interested to study the matter for themselves from original sources. Since that time the following papers have been read and published: " The Bertrand-Thiel Process of Making Steel," by Percy C. Gilchrist (Cleveland Institution of Engineers, Session of 1896-

Jan 1, 1899

Discussion of the paper of Dorsey A. Lyon and Robert M. Keeney, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 2117 to 2149. C. D. WOODWARD, Butte, Mont.:-We constructed a small blast furnace, and used first carbon electrodes and an alternating current of about 50 to 75 volts. We were able to smelt the material which was fed to the furnace, but we did not carry on experiments far enough to see just exactly what the power consumption was and compare it with the amount of material treated. We found that the blast seemed to help materially in reducing our charge and cutting down our power consumption. There were several other experiments tried at the time, and I do not call to mind now just what they were. We were trying to do away with the carbon electrode and replace it with an iron one, and it also seems to me we tried to use the ore for an electrode; but I believe that the electric furnace in the reducing end is simply a question of British thermal units per kilowatt-hour compared with British thermal units in a pound of coke. Now, if a pound of coke costs us 0.5 c. and a kilowatt-hour costs us in the neighborhood of 1.5 c., I think there is a big advantage in using coke instead of the electrical current for copper reducing. We tried steam, and a number of other methods, to throw copper down, but it has been some time ago and I am not very familiar with them now. The outlook of the experiments did not seem to be very promising, and we took it more as a thermal problem than an electrical one. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-Mr. Woodward has spoken of the question as a thermal problem. I would call attention to the fact that electric furnaces usually utilize the heat of the electric current at from four to ten times the efficiency with which the heat generated by fuel is utilized; so it will not do simply to compare by thermal units generated. Your total thermal units may cost much less from coke than from electricity, yet you will find the electrically generated thermal units utilized in a properly designed furnace from three to ten times more efficiently than in the combustion furnace. You must make that allowance is comparing the cost of thermal units generated electrically and thermal units from coke.

Jan 11, 1913

By D. A. Bailey, F. L. Kadey

During recent years, expanded perlite has found extensive use in a wide variety of commercial applications. Specifications for a range of uses call for aggregates having different physical properties and requiring various types of processing. The mitre scopic examination of expanded aggregates in specially prepared thin sections has yielded important information regarding internal structure and can be a useful aid in evaluation of the product. Perlite is an acid volcanic glass containing from 2 to 5 pct combined water. When crushed and rapidly raised to a temperature of 1500° to 2100°F, the volatilization of the combined water, coincident with softening of the siliceous glass, causes the particles to expand or pop. Expansion of perlite to densities as low as 1-1/2 lb per cu ft has been achieved, although the normal range is from about 2.5 to 10 lb per cu ft. Low-density materials of this nature have found application in cryogenic insula- tions, insulating tile and board, plaster and lightweight concrete, soil conditioners, filter aids after comminution, and a host of other uses. The expansion of perlite may be controlled by a number of variables. Some of these are ore milling, furnace design, expanding temperature, use of preheating techniques, screen size distribution, and feed rate of the crude. For the specific intended uses, the art of perlite expanding has developed to the point that much is known about the effect of these variables on the end product. The requirements, however, for an aggregate to be used in plaster are different from those for an expanded perlite to be used in lightweight concrete or for cryogenics. In the study of perlite, many practical questions remain unanswered. One of the most important is, "why do some perlites make hard aggregates while others cannot resist crushing or compaction?" The usual tests and methods for evaluation of nonmetallic substances have been tried and have contributed their share to our knowledge. But chemical analyses, compaction resistance tests, screen analysis, etc., will reveal only a limited amount of information. The answers to these complex questions may well be found in an examination of the intemal structure of the expanded particle. Such questions and the ex-

Jan 1, 1962

By Sherwin F. Kelly, Bela Low, William B. Creagmile

Electrical methods and instruments for geophysical exploration have been almost exclusively applied, during these years of development of the art, by a few companies specializing in this field. The control of patents, the cost of the instruments and the general lack of published information on details of field procedure and office interpretation have given these owners a monopoly in carrying out electrical surveys. The development of the Megger Ground Tester1 seems likely to change this situation, and to enable mining engineers and geologists, without special training in geophysics, to carry out simple reconnaissance electrical surveys. Nevertheless, the need for such special training and experience in planning surveys and interpreting their results remains, and probably i always will remain, indispensable for a successful outcome. The unique thing about, the Megger Ground Tester, which gives rise to this hope for its general use, is its simplicity of operation. The four binding posts of the instrument are connected by insulated wires to four stakes driven into the ground at appropriate points. The crank of the Megger is then turned, and the resistance of the ground between the two inside stakes is read directly, in ohms, by the deflection of a pointer over a scale. The apparatus is shown in Fig. 1. Fundamentally, the principle of operation is that of determining the resistance of a four-terminal conductor, as applied by Frank Wenner to the measurement of earth resistivity. "A four-terminal conductor is a conductor provided with two terminals to which current leads may be connected and two terminals to which potential leads may be connected. The resistance of such a conductor is the difference in potential between the potential terminals divided by the current entering and leaving

Jan 1, 1932

By Leo F. Reinartz

This is the fourth and final installment of Leo Reinartz' summation of the steelmaking industry over the first one hundred years. ALTHOUGH basic open-hearth steel has been in the limelight for many years, it has had to share some of its glory with two lesser but nevertheless important rivals, one 50 years old and one a rejuvenated process. Electric steel Electric-steel manufacture began in a humble way in the United States in 1906, when the first heat was tapped from a 3-ton Heroult electric furnace at the Halcomb Steel Co., Syracuse, N. Y. During the intervening years, it has completely eliminated the crucible process. For many years electric melting furnaces were located predominantly in relatively small, nonintegrated plants, making all kinds of high-grade alloy steels. Most of these furnaces, with capacities ranging from 5 to 20 tons, had basic bottoms. During and after World War II, many large basic electric furnaces, some up to 200 tons in capacity, were installed in integrated plants to make commodity steels. There were several reasons for building electric furnaces. Capital investment per annual ton of capacity was low and furnaces could be installed quickly. Since these furnaces used mostly scrap iron in the charge, no extra expensive coke- and blast-furnace capacity had to be added. The perfection of the top-charging design, and the development of large transformers and furnaces, made possible tons per hour as high as from modern 350-ton. open-hearth furnaces. Electric furnaces have high availability and repair costs are low. The process is flexible. Alloy and plain carbon steels of high quality can be made. Where power costs are low, the operating cost can

Jan 1, 1961

By A. R. Kinkel

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)—Mr. Kinkel's article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel's conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel's nomenclature being used. The first member, which Mr. Kinkel terms the upper unit of the Balaklala rhyolite, consists of a single, massive, homogenous body of very silicious igneous rock, consisting almost wholly of quartz and albite, and averaging about 80 pct silica. Most geologists of the U. S. Geological Survey who have previously inspected the district have called it an alaskite. It is not a pile of several members, but is a single unit, without internal subdivisions. It has the form of a recumbent lens, approximately flat on the bottom and arched on top, several miles in diameter, and attaining a maximum thickness of 1000 to 1200 ft. It varies in texture from porphyritic to holocrystalline, and contains unusually large quartz phenocrysts up to 4 mm diam. Mr. Kinkel considers this formation to be a thick lava flow that is older than the overlying Kennett shale, while the writers interpret it as being intrusive, constituting a domed sill or laccolith that is younger than the Kennett shale. Their reasons are as follows: 1) This formation shows none of the features which within the writers' experience invariably accompany very silicious lava flows. Nowhere is it vesicular; nowhere does it contain any glass or its devitrified equivalent; nowhere does it contain flow breccia; and nowhere has it a ragged top, in spite of the fact that there is no evidence of surface erosion, which might have removed such a top.

Jan 1, 1957

IN CIRCLES where mining men are wont to fraternize, a statement often heard is: "Yes, I spent six (or two, or ten, or thirty) years down at 'Chuqui.' " This means Chuquicamata, the site in Chile of what in all probability is the world's largest deposit of copper ore. One hears similar remarks regarding Braden and Andes, and, in fact, regarding a score of other big mines in South America, Africa, and elsewhere, but Chuqui seems to lead the others as the locale of engineers who have done a stint in foreign countries. One reason probably is that it is the Anaconda Company's premier foreign operation. Because of its unusual size and the diversity of its operations a great many men are needed. It is a sort of training school for young engineers; but, also, Anaconda has sent down a great many mature members of its big organization for special assignments like metallurgical research or plant construction. Chuquicamata is about 150 miles northeast of Antofagasta, at an elevation of 9,500 ft. It is in an almost rainless desert country where the wind (it is alleged by some) blows most of the time. However, the copper mining entrepreneurs have done their best to make up for what nature has neglected to do in creating a pleasant environment for the people who operate the mines. These include about 160 "foreigners" of whom 86 are from the United States, most of them accompanied by their families. There are 165 Chileans on the staff. Comforts, conveniences, and many luxuries are provided to offset in some measure the disagreeable features of the climate. Nevertheless, as I have implied, engineers at Chuqui generally jump at the chance to become "alumni" when opportunity offers. At the same time, they appear to take pride in their alma mater.

Jan 1, 1957

By E. B. Swanson

FREQUENT reference has been made to the increased domestic gasoline demand recorded for 1931. This increase was in the neighborhood of 7,000,000 bbl. Although smaller relatively than that to which the oil industry had become accustomed by virtue of the experience of preceding years, the increase was of substantial amount, particularly at a time when any increase at all could be regarded with eminent satisfaction. Less has been said, however, of the 18,000,000 bbl. decline in gasoline shipments to territories and foreign countries. When the loss of business outside the United States is combined with the domestic increase, there results a net loss of some 11,000,000 bbl._ in total gasoline demand. The gain of 2 per cent in domestic sales gives way to a loss of 2.5 per cent in total domestic and foreign sales. The United States actually has been losing ground in the international gasoline market since 1924, when shipments from this .country equaled 72 per cent of the gasoline shipments from the leading gasoline-producing countries of the world. A loss in relative standing was recorded with each succeeding year. As long, however, as gasoline shipments showed an actual increase, the loss in relative standing was of little concern. Foreign producing centers annually supplied an increasing share of the foreign gasoline markets, but, until the past year, the demand abroad con-tinued to increase at a pace which could accommodate all of the, increased output of foreign plants and yet require increasing quantities from the United States. It was not until 1931 that the various factors were combined so as to produce an actual and substantial decrease in the foreign demand for United States gasoline. Consumption in foreign countries generally declined, while the output of foreign refineries and the foreign manufacture of substitute fuels continued to increase. From our own viewpoint, this meant a loss of some 18,000,000 bbl. of gasoline busi-ness in foreign countries, one-half of it probably due to the lowering in foreign demand and the other half to the increased output of foreign refineries and the increased utilization of substitute fuels.

Jan 1, 1932

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942