Search Documents

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By Herbert F. Miller

For a long time I have believed that the gas- and brick-costs of open-hearth furnaces using prodncer-gas could be greatly decreased by a change in the design of the port, which would materially reduce the first-cost of the furnace, the rebuilding-cost, and the repair-cost. The defects of the present type of such furnaces, which has clone duty for so many years, may be studied in Fig. 1, in which A A are the two air-uptakes, B is the gas-uptake, and C the end of the gas-port. In the present type of furnace, C is practically 011 the edge of the bath and therefore combustion begins to take place at that point, but has no effect until the gas passes from 5 to 10 ft. into the hearth. As the furnace grows older, C moves back by reason of the burning or falling down of the arch. The furnace reaches its highest efficiency when C has moved a certain distance, but is still near enough to the bath for the overhead layer of air to hold the gas down on the bath, and far enough back to permit combustion to take place at some distance from the bath. This latter fact means that the temperature is sufficient to melt steel at the edge of the port. From this time on, the furnace decreases in efficiency. What is the reason ? As C moves further hack, the gas is released from the gas-port at a point where there is little or no overhead layer of air. The result is that the gas floats along the roof, with the air mostly underneath it. Why the air does not stay over the gas is readily seen in Fig. 1. The lines of draft naturally run parallel to the length of the furnace. The air-uptakes being on the sides and the gas-port in the middle, most of the air will naturally be drawn along the sides of the furnace and the layer of air will be thinnest over the gas, where it is most needed.

Jan 1, 1914

By Carroll F. Hardy

THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer- subsidized private utility atomic power plants on one hand and super TVA&apos;s on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 ½ million units were lost in this 10-year period.

Jan 3, 1954

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

By Wilbur Nelson

ALL of our accounts of the discovery of copper ore at Ducktown, Tenn., state that the discovery was made in August, 1843, yet it would appear that samples of copper from this district were found by the Spanish explorer, DeSoto, when he wandered into Southern Tennessee, in 1539, in his four years of exploration through the Southern States. The following quotation is taken from his diary: "Towards the north there was a province named Chisca; and that there was a melting of copper, and of another metall of the same colour, save that it was finer, and of a farre more perfect colour, and farre better to the sight, and that they used it not so much, because it was softer. And the selfe same thing was told the governor in Cutifa-Chiqui, where we saw some little hatchets of copper, which were said to have a mixture of gold. But in that part of the country it was not well peopled; and they said there were mountains, which the horses could not passe; and for that cause, the governor would not goe from Cutifa-Chiqui directly quicker." DeSoto sent two of his company to try to find these mines, but after five days&apos; wandering through the mountains they returned, stating that their guides had become lost. Although the Ducktown area may have been known to the ancient Indians, it was not until August, 1843, when a Mr. Lemmons, who was panning for gold on Potato Creek, in the Ducktown basin, found some reddish-brown decomposed rock, which he supposed to be gold, that the copper deposits were actually discovered. His disgust on finding that this yellow metal. was not gold was so great that he did not. try to develop his find. In March, 1847, B. C. Dugger erected an iron forge at this same place, but was unable to work the iron as it contained so much copper that on cooling it would break to pieces. The finding of copper in the iron ore by Mr. Dugger led to further explorations; and in April, of the same year, A. J. Weaver, who was passing through that country, told the people that the black rocks they had dug out were rich copper ore. Mr. Weaver began the first mining in this district.

Jan 10, 1924

By G. G. Luther, C. E. Jackson

The relationship between hardenability and weldability has been mentioned many times. The ease of making a hardness survey has led to its wide use as a criterion of weldability and with a given class or series of steels for which the ductility under weld heat-treatment is known the test is entirely suitable. However, in studying a new steel the hardness survey is of less value, since it is based on the assumption that there is a correlation between hardness and ductility. Several attempts have been made to derive indices for weldabilityl and hardenability from the chemical analysis. In most of these proposals the effects of the different elements were considered to be additive, but recently Grossmann2 proposed a novel method of calculating the hardenability of a steel from its chemical composition. In the method proposed, a steel is considered as having a base hardenability due to its car- bon content and grain size, and this base hardenability is multiplied by a factor for each chemical element present. The final product is the hartlenability. The purpose of the present study is to point out the possible relationship between hardenability and the effect of welding on hardness and ductility for a number of plain carbon and low-alloy steels. The composition of the 25 steels reported in this paper as determined by chemical analysis is given in Table I. To eliminate the effect of variations in finishing temperatures, the 1/2-in. plates were normalized after heating for one hour at 1650°F. in a con-trolled-atmosphere furnace. In making comparative tests, it is essential to hold conditions as Constant as possible; hence full automatic weltling control was used. The electrodes, all supplied by

Jan 1, 1943

By Eugene H. Cowles

The German silver industry of the United States amounts in value to upwards of $6,000,000 or $8,000,000 annually. Several thousands of people earn a livelihood pursuing it, and the beautiful goods and articles manufactured from this time-honored and valued alloy are everywhere visible. German silver enters largely into our street signs, harness and house hardware, and all manner of table-ware, solid or plated. There is scarcely an hour in the day that German or nickel-silver is not before our eyes. The composition of this alloy is a very uncertain thing, and depends largely on the honesty of the manufacturer and the price the purchaser is willing to pay. It is composed of copper, zinc and nickel in varying proportions. The best varieties contain from 18 to 25 per cent. of nickel, and from 20 to 30 per cent. of zinc, the remainder being copper. The more expensive nickel-silver contains from 25 to 33 per cent. of nickel, and from 75 to 66 per cent. of copper. The nickel is used as a whitening element; it also strengthens the alloy and renders it harder and more non-corrodible than the brass made without it, of copper and zinc. Moreover, it reduces the odor emanating from brass, which is so disagreeable if it occurs about the dining-table. Of all troublesome alloys to handle in the foundry or rollingmill, German silver is the worst. It is unmanageable and refractory at every step in its transition from the crude elements into rods, sheets or wire. As a white-headed furnace-man recently said to the writer, in one of our large mills, " you can put eight crucibles into the fire, each containing exactly the same mixture of German silver, and when you take them out and pour them into slabs for rolling, seven will be a mass of scum or slag, or the stuff will swell up like rising bread and overflow the moulds, and be so full of blow-holes that it will look like a sponge. The eighth crucible will contain perfectly good metal. On remelting the next day, the bad stuff will, in nine chances out of ten, come out just as good metal as the eighth pot the day before, and under apparently the same conditions." With nickel at seventy or eighty cents per pound, German silver

Jan 1, 1890

By J. W. Rutter, K. T. Aust

Observations are presented of the formation of annealing twins during the growth of a recrystallized grain into a striated, melt-grown crystal of high-purity lead. The formation of an annealing twin resulted in replacement of the original migrating boundary by a large-angle grain boundary of the caincidence-site type or by a near-twin boundary. The results support the Fullman-Fisher theory of annealing twins and demonstrate the usefulness of the coincidence-site model. FULLMAN and Fisher1 have advanced the following theory to account for the formation of annealing twins during grain growth. Whenever a grain A grows into a matrix of grains S1 and S2, a twin A&apos; of grain A may form, as shown in Fig. 1, if the following energetic condition is satisfied: where "E" and "a" refer to the specific interfacial free energy and the area, respectively, of the boundaries indicated by the subscripts. In effect, the twinned grain will persist when the energy of the boundary between the twin(A&apos;) and the matrix grain (S, or S,) is less than that of the boundary between the original growing grain (A) and the matrix grain by an amount which exceeds the energy of the coherent twin boundary between A and A&apos;. Experimental observations on the changes in grain boundary free energy accompanying the formation of twins1 are in agreement with the theory outlined in Eq.[l]. Direct observations of the formation of annealing twins at moving grain corners1"3 and the depend-

Jan 1, 1961

By J. E. Pogue, F. G. Coqueron

This paper describes the sources of funds required by the petroleum industry to finance capital expenditures and also presents a discussion of the effect of rising construction costs on these expenditures. The petroleum industry obtains its capital funds from several sources: (I) internal, from retained cash earnings; and (2) external, from borrowings and the sale of securities to the public. The upward trend of capital expenditures of the petroleum industry is caused in the main by the influence of two powerful factors: (I) the physical growth in the demand for oils; and (2) the rising cost of drilling wells and constructing refineries, pipe lines, and other facilities. The segregation of these factors is accomplished by deflating the actual capital expenditures so that they are shown in terms of 1939 costs and then subtracting the adjusted series from the actual figures to yield a set of data representing the expenditures made on account of higher costs. Rising costs affect prices and the portion attributable to this factor had to be generated from the cash earnings of the industry, which called for higher oil prices. Introduction Capital may be defined as "wealth employed in or available for production." All production requires capital. Expanding industries require more capital than static ones, and technological industries employ more capital than. those in which little equipment is needed. The petroleum industry is both rapidly growing and highly technological, and, being a large industry, its capital requirements are prodigious, amounting to about one-seventh of the total of all American business, excluding agriculture.* Capital formation may be defined as the method by which the wealth or capital needed in the productive processes is created. There are various ways in which capital funds may be obtained but there is only one way in which capital can be created—out of production in excess of consumption, that is, savings. The physical realities are simple, but the monetary concepts are complicated because the mechanism of credit can draw upon future savings. Source of Capital Funds An industry, such as the petroleum industry, can obtain its capital funds from

Jan 1, 1949

By Neil O. Johnson

In the cyanidation of gold, silver and mixed ores, the solids, suspended in the pulp after fine grinding, primary settling and scries agitation arc subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D The conventional C.C.D. plant consists of a series of separate thickeners—three to five in number—arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they arc diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in scries instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and scal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-:trice with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a diaphragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company&apos;s well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By A. Patton

Introduction THE use of roll scale in the Bessemer process dates back, to the "best of our knowledge, at least 20 years. It was first used by the Ohio Steel Co.; Youngstown, Ohio (now the Ohio Works of the Carnegie Steel Co.) under the direction of Sam, MacDonald, Superintendent of the Bessemer Department at these works. Two 10-ton vessels and one blowing engine capable of blowing one heat at a time were employed. The object of using the scale was to -shorten the length of the blow; or in other words, to increase the production with the same equipment. Various means were tried out for introducing the roll scale into the bath of molten iron: It was shoveled into the vessel before the heat was charged, so that the metal would flow over the scale; it was shoveled into the bath after the vessel was turned up; it Was dumped into the empty iron ladle by the wheelbarrow-load, and at times wars dumped on top of the molten metal in the iron ladle. But the practice of introducing the scale into the iron ladle had to be abandoned on account of danger from explosions and of skulling the -ladles. It was soon learned that the proper place to charge the scale was in the empty vessel, so that when the molten iron was poured into the vessel it flowed over the scale, causing a considerable reaction to take place before the heat was turned up. Eventually, cylindrical chutes similar to those now in use were installed. Into these chutes the scale is dumped and carried into the empty vessel. Before this convenient means of introducing the scale was adopted, the Ohio Works had satisfactorily demonstrated that roll scale would increase production, by blowing 107 heats in one 12-hr. turn (1,087 tons) with one blowing engine, blowing one heat at a time; whereas, prior to the use of scale, the best practice at these works was about 80 heats under the same conditions.

Jan 2, 1917

By Robert Hunt

ONE of the most serious and important economic administrative problems facing American railway authorities to-day is that of their rails, and it is one to which much thought, is being given, not only by the executive officers of the railways and the manufacturers of the steel rails, but also by State and National commissions. It is realized by many and admitted by some that the present situation is one which cannot continue. The roadways of railways must be made more secure, or the weight of rolling stock and the speed of trains must be lessened; and the desired result must be attained with the minimum outlay of money, both in expenditure on plant and in cost of operation. If the investment per mile is too large, or through the lessening of tonnage and efficiency of equipment the cost of operation is too great, the desired and demanded cheap service cannot he rendered to the public. Therefore, the weight of equipment cannot be greatly reduced, and lessening the rapidity of service would be far from satisfactory; consequently, the safety of the roadway must be secured with the least practical outlay. It is imperative that the roadbed should be properly graded, with the fewest practically possible curves; that it should have good ballast, be well drained, have good ties properly spaced, and be laid with sound rails of suitable weight, efficiently joined together, and that the whole property be carefully and intelligently cared for. My province is to treat of the sound rails. During the last few years there has been renewed interest in and discussion of that question, and I know that many rail makers not only have been and are desirous of maintaining the highest standards of manufacture which they may have attained, but have been and are seeking to better their product, in several instances devoting much time and money to that end. At the same time, they realize that the cost of any improvement in quality which they may accomplish must be kept within certain commercial bounds; and that fact is as fully understood by their patrons as by themselves, and it should be kept in mind by all who discuss the question.

Jan 2, 1914

By Charles Ramseyer

THE manufacture of iron and steel is one of the largest of our indus-tries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally con-sidered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process indus-tries have been born and developed, and not seldom completely revolu-tionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subse-quently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of -the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie&apos;s ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress. was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1934

By A. G. Metcalfe, Koeneman

A study of the structure of chemically deposited nickel by Goldenstein, Rostoker, Scpssberger, and Gutzeit has been reported recently. In this work it was shown that the nickel deposit produced by the catalytic nickel-reduction process was an amorphous solid. Crystallization occurred at elevated temperatures when the original powder pattern which showed only a diffuse ring with a d-spacing of 2.01A became sharp, revealing nickel and nickel-phosphide lines. The phosphide was indexed provision%lly on a tetragonal lattice of parameters a = 9.01A and c = 4.42A, which is in reasonable agreement with the structure of Ni3P proposed by No-wotny and Henglein.3 The transformation from the amorphous to the solid state occurs abruptly (e.g., after 7 min holding at 400°C) with the evolution of considerably more than 1000 cal per gm-mole. A more detailed analysis of these effects requires a knowledge of the solubility of phosphorus in nickel. Konstanti-now3 mapped out the phase diagram in 1908 but did not determine the solid solubility. The eutectic was placed at 11 pct P and 880°C. The purity of typical catalytic nickel deposits is very high.&apos; Spectrographic analysis for heavier elements showed only trace amounts of aluminum, calcium, iron, magnesium, lead, and silicon. The term "strace" is a qualitative definition for less than 0.1 pct and probably less than 0.01 pct. Analysis for the interstitial elements yielded 0.04 pct C, 0.0023 pct 0, 0.0005 pct N, and 0.0016 pct H. Some of this material with 7.5 pct P was used in the present work. EXPERIMENTAL METHODS Alloys were prepared from carbonyl-nickel shot and a master composition containing 7.5 pct P. Cold-crucible, nonconsumable-arc melting was used.

Jan 1, 1959

By H. J. Stehli

Probably the earliest sinter from lead ore was made in the product sinter boxes attached to some hand reverberatory roasters. The ore was drawn from the roaster bed when dead roasted, and then by laborious effort fritted together by rabbling at a high temperature in the sinter box. This was not a true sinter, but was a great improvement over the dusty dead-roasted fine ores. The Huntington-Heberlein pots were the first real advance in the art, and produced some real sinter. They required that the sulphides be preroasted to 5 or 6 per cent sulphur, and the long cycle of operating and deep bed of material used in the pots fostered the formation of densely fused material and fines. This necessitated crushing of the densely fused cake and returning to the next charge large amounts of fines screened out. The Huntington-Heberlein pots made comparatively high lead losses because the deep bed and high internal temperature together favored the volatilization of lead. Lime (CaO) was added to the charges, and this addition constituted the patented feature of the Huntington-Heberlein process. Its sole function we now know was to act as an isolator of the sulphide particles, and any other substance—for instance, iron oxide—of equal fineness performed the same function. The Savelsberg process used limestone instead of burned lime, and in this there was a definite advantage. The converting of CaCO3, to CaO is a highly endothermic reaction, so the lime acted not only as an isolator of sulphide particles but absorbed excess heat and to some extent prevented premature fusion of the sulphides. The Carmichael-Bradford process used gypsum instead of limestone, and had the disadvantage of adding more sulphur to a charge from which it was desired to eliminate sulphur. Here again the gypsum served only as an infusible isolator of sulphide particles. The first Dwight-Lloyd apparatus to sinter lead ores commercially was installed at Perth Amboy in 1907. The fact that lime in any form was necessary to sintering was quickly disproved by making excellent sinter from Bunker Hill and Sullivan table concentrates, silica sand and iron oxide only.

Jan 1, 1937

By Jesse Betterton

IN the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200° to 1300° F. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accom-plish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flow of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The, process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes.

Jan 1, 1933

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889