Search Documents

The Mineralogical Researches of Gold Ores and Technological Products at Operating Factory in Olympiada Mine (Russia)

Sep 13, 2010

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007

By Peter Fullagar, Adel Vatandoost, Steve Walters, Toni Kojovic

"Traditional comminution tests are a vital component in every mine plant design. Comminution behavior governs both the cost of equipment and its operating efficiency. Most comminution tests are conducted off site on a limited number of samples, owing to the high costs and long lead times involved. Therefore a strong incentive exists to find alternative means for efficiently characterizing comminution behavior for a truly representative suite of samples. The potential for inferring comminution behavior from drill core is investigated in this paper. Our approach involves development of small scale comminution tests on the one hand, and measurement of a wide range of core attributes on the other. Our focus is the relationship between petrophysical properties and comminution behavior.Petrophysical properties of archival diamond drill core from the Ernest Henry Mine (Queensland, Australia) have been measured using a Geotek multi-sensor petrophysical core logger. We have investigated the relationship between the petrophysical properties and the corresponding small scale A*b and estimated Bond mill work index test results for 2m composites of the core. Core samples were petrophysically classified by means of cluster analysis. Comminution behaviour was then modeled for each cluster via multiple regression. The results suggest that prediction of the comminution behavior on the basis of petrophysics is viable at Ernest Henry.INTRODUCTIONMineral processing is the most important downstream operation for mining engineers and metallurgists since most mined materials are subjected to some type of comminution or beneficiation operation (SME, 1992). Comminution or size reduction is typically the first stage of processing. Size reduction steps (crushing and grinding) in any plant consume large amounts of energy, normally more than 50% of total energy (Weiss, 1985). Therefore, it is desirable to obtain laboratory results to design the size reduction equipment appropriately. One of the main factors that control the selection of hard-rock crushing equipment and the design of a crushing circuit is the mechanical character of the ore(s). Work index, density, abrasivity, compressive strength and clay content are essential parameters for ore characterisation (SME, 1992)."

Jan 1, 2009

By François G. Bernardeau

Cement-bentonite (C-B) slurry walls have been used for ground water cutoff in deep excavations, contamination containment, and other applications. Hydraulic conductivity is of great concern for cement-bentonite slurry walls. The quality control program usually specifies permeability and strength tests to be performed in a laboratory on samples cast in the field and cured for a certain time. Currently there is no widely accepted in-situ test method for the performance of the constructed slurry wall. A recently constructed cement-bentonite slurry wall in South Carolina included a 200-foot-long test section done in advance of the production of an 8,300 foot-long wall. Intensive tests and investigation were conducted during and after the test section construction: Monitoring piezometers were installed using wet insertion method and packer tests were conducted in boreholes drilled in the post-28-day-cure slurry wall. The permeability measured from the packer tests was about two orders of magnitude higher than the design and the laboratory test values. Additional investigation was performed using a video camera to inspect the borehole walls especially the packer test sections. Test pits were excavated to observe both sides of the cement-bentonite slurry wall. A thorough inspection was conducted to evaluate the integrity of the wall. The lessons learned and issues regarding the disturbance effects of in-situ testing of cement bentonite slurry walls is presented and discussed.

Jan 1, 2008

By C. J. A. Mcewan, C. M. Rice

The Rosita Hills contain rich, vein- and breccia pipe-hosted precious metal deposits. Volcanic activity occurred in two cycles - an early, mainly andesitic cone-building phase that terminated in the formation of a caldera and breccia pipes and a later phase characterised by trachytic lavas and dykes, rhyolite domes and lamprophyre dykes. Alteration consists of weak propylitic and argillic and, locally, intense advanced argillic, K-feldspar sericitic and silicic types. Marked trace-element depletions (Rb, Sr, Zn, Mn) are associated with K-feldspar-sericitic alteration and with advanced argillic alterations, whereas enrichments (Pb, Ag) are associated with K-feldspar-sericitic alteration. Gold distribution is highly localised and is controlled by breccia pipes and a caldera ring fault; it is not related to district scale alteration. In general, the geochemical and alteration patterns are complex, but they are clearly influenced by linear structures, the caldera ring fault and breccia pipes. Pipe-hosted Au-Ag and vein-hosted Ag mineralisation are associated, respectively, with early andesitic and late, post-caldera rhyolitic activity. The pipe-hosted and, especially, the vein-hosted mineralisation show affinities with adularia-sericite-type epithermal deposits

Jan 1, 1991

Interest in the tantalum-niobium minerals has been greatly stimulated in Western Australia by the fact that these rare minerals occur at numerous localities in that State, and in the adjoining parts of the Northern Territory, sometimes in mineable concentrations, as at Wodgina and Greenbushes. A large proportion of the world's tantalum comes from these deposits. The late Dr. E. S. Simpson, in particular, made an extensive study of the chemistry and mineralogy of these minerals, and the following observations are based upon the examination of specimens which he and Mr. H. Bawley, Government Mineralogist of Western Australia, have submitted to me for examination from time to time. The fact that so many of the specimens have been analysed provides a unique opportunity for the interpretation of the phenomena observed in the polished sections.TANTALITE-COLUMBITE SERIESIt has long been considered, on the basis of crystallographic form, chemical analyses, and specific gravity measurements, that ferrotantalite (FeO. Taz05), manganotantalite (MnO. Taz05)' ferrocolumbite (FeO. Nbz0 5), and manganocolumbite (MnO. Nbz0 5 ) form a complete isomorphous solid solution series (Simpson, 1937) and this is confirmed by study of polished sections of these minerals, Pehrman (1929) examined a series of five analysed specimens with Nbz0 5 contents as follows:-

Jan 1, 1940

By Robert H. Ridgway

This circular outlines salient facts regarding the sulphur industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. It will welcome comments, criticisms, and contributions of data that may assist in making later editions of this circular more accurate, or in developing more fully the bureau's mineral files pertaining to sulphur. Throughout this paper sulphur is used to designate crude sulphur or brimstone, not sulphur produced from pyrites or' smelter gases.

Jan 1, 1930

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By Hargraves A. J

The paper outlines events at the Collinsville State Coal Mine, Queensland, leading to the practice of full face multiple shotfiring in bord and pillar development places. The 1954 disaster is referred to, and factors involved in simultaneous shotfiring in coal are discussed. Promising preliminary multiple shotfiring tests at the Colliery are described, as well as the resulting routine measures adopted, and the changes involved. The subsequent inducing of two outbursts under safe conditions by remote multiple shotfiring is given as justification for the changes made.INTRODUCTIONFollowing a disastrous instantaneous outburst (1.0.) of coal and gas at the Collinsville State Coal Mine in 1954, the necessity for inducer shotfiring for the control of possible further outbursts was established. However this mine, immediately classified as gassy after the 1954 outburst, is subject to the general restrictions pertaining to gassy mines which at present preclude the use of inducer shotfiring due particularly to the non-existence of a permitted exploder for more than six shots, and further, because permitted multipleexploders are not designed for remote firing through long lengths of cable. This situation was met by arresting or reducing progress in the production places, thereby reducing the danger of outbursts while means were being considered to achieve overall maximum safety.In August 1957 two full faces were successfully blasted in experimental simultaneous rounds. In June 1958 four full faces were blasted, and in October 1958 full face grunching without prior cutting, Le. inducer shotfiring, was introduced in No. 1 Tunnel as a production feature. In March 1960 it...

Jan 1, 1960

By Kimiz Dalkir

Some things to keep in mind? ! What is your role in knowledge management? ! What knowledge-related challenges are you facing today? ! How does important knowledge get shared in your organization? ! Can you name factors that enable/block innovation and organizational learning in your work context? A brief history of KM? ! Top-down / imposed ! Rigid / bureaucratic ! Slow deployments ! Expensive ! Unpopular: empty libraries, info-junkyards, low adoption rates ! Problems measuring success ! The result: traditional KM is not the answer

May 1, 2003

By M. R. McKenzie

This paper describing the milling methods at the Walkermine concentrator, Plumas County, Calif., is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to James O. Elton, manager of the International Smelting Co., and to Henry A. Geisendorfer, manager of the Walker Mining Co., for permission to present this paper; to H. A. Geisendorfer and J. D. Roberts, shift boss, for historical facts, and to D. D. MacLellan, geologist, for geological information.

Jan 1, 1932

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959