Search Documents

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

The point of the anode effect on carbon anodes of dcfincd surface area. during electrolytic decomposition of alumina dissolved in molten fluorides. has been determined from current-voltage curves. The reproducibility and accuracy was found to be better for cell voltage than anode current density. Results have been obtained for the effect of alumina concentration temperature and carbon type. The point of the anode effect was strongly dependent on both the alumina concentration and the carbon type. For high alumina concentrations it has been found that the anode effect approaches reversibility. From these results it is concluded that co-evolution of CO, and CF. occurs prior to the onset of the anode effect. The anode effect results when the CF, content becomes sufficiently high for the melt not to wet the electrode surface and is maintained because of the slow desorption of CF, and the high electrode potential that results.

Jan 1, 1967

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998

By Shahé Shnorhokian

A study was conducted on the seismic activities and associated rockburst events that took place at an underground Canadian metal mine over a period of five years. In the first stage, a back analysis of the microseismic database led to the identification of clusters of major events. The locations of these clusters were identified with respect to the local geology and the planned mining sequence. In the second stage, a numerical model was constructed using the finite difference code FLAC3D to simulate the in-situ stress, mine geometry, local geology, and stope sequence. Mining-induced stress fields were compared against two rockburst events that took place during this period, as well as against the various geologic units present. It was shown that by combining microseismic analysis and numerical modeling, it was possible to provide a basis for evaluating the influence of the in-situ stress regimes and stope sequencing on mining-induced seismic response.

May 1, 2011

By Franklin J. Stermole

L. Alan Weakly, member SME, is a senior staff engineer, Exxon Co. Weakly chaired a Mining Engineering committee formed to solicit materials for six planned "personal skills" articles, to be used in ME this year. What follows are Weakly's introductory comments to the series. Upon graduation from college several years ago, I thought that I was sufficiently prepared to embark in my chosen profession. A short time later I realized that several years of on-the-job training was going to be required before I could use my technical training effectively. It never occurred to me that, professionally, I was seriously lacking in any other skills. My spelling could use a little upgrading, but this was not a serious deficiency. I have been very fortunate to have had two employers that recognized that their engineering professionals did lack other skills and made every effort to give them training to correct these deficiencies. The skills I am referring to are those in administration and interpersonal relationships. Most mining engineers and geologists receive very little, if any, college training in these areas. In addition, many companies do not provide this training and many mining engineers and geologists are unaware of their deficiencies. It is for this reason the subject of personal skills development is being introduced in Mining Engineering. The mining engineer or geologist can pursue one of two basic career directions, managerial or technical. In today's technically sophisticated society and highly competitive business climate, both orientations require administrative and interpersonal skills. Most of us are technically qualified and we continue to upgrade our technical skills. But many studies indicate that we, as a group, are significantly weaker in administrative and interpersonal skills than other professional groups. In addition, these studies indicate that engineers, in general, take longer to reach managerial levels and fewer do so. This series in Mining Engineering, then, should help readers strengthen and broaden their professional capabilities. In all industries, including mining and petroleum, economic analysis of potential investment projects is done to select the projects that will give maximum future value from the investment of available capital. Rather than looking directly at the future values to be generated by investing capital in alternate ways for economic decisions, evaluators usually use either rate of return, present value, annual value, a profit to investment ratio, or various break even analysis results to reach economic analysis decisions in evaluating alternative investments. Alternative economic evaluation techniques are used in industry to properly analyze the economic potential of various investment projects. "Discounted Cash Flow" analysis is the phrase commonly used to describe these techniques. Whether you want to analyze projects in mineral, petroleum, real estate, refining, pipe-line transportation, or any other industry, proper application of discounted cash flow analysis techniques enables you to fairly compare the economic potential of alternative projects as well or better than you can using any other project evaluation approaches. It should be pointed out that investment analysis generally involves more than economic analysis. Financial and intangible considerations sometimes are as important or more important to investment decision-making than economic considerations. Economic analysis refers to evaluation of the profit generating potential of projects, that is selecting which alternative projects will generate maximum future value possible from available investment capital. Financial analysis, on the other hand, relates to analysis of where money is going to come from to finance various projects. Regardless of the economic potential of a project, if financial analysis indicates that we cannot finance the project, it likely will be shelved for financial reasons even though it may be economically satisfactory. Many evaluators use the terms "economic analysis" and "financial analysis" interchangeably, but this author considers that to be undesirable. Intangible analysis relates to project factors that are difficult to quantify in

Jan 2, 1984

By P. Venkatraman

Laboratory and pilot-scale test data have shown that the innovative feed presentation of the CrossFlow separator provides improved metallurgy when compared to traditional hindered-bed or teeter-bed classifiers. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Recent side-by-side industrial-scale evaluations have verified that this technology can improve overall efficiency, reduce the cut point of separation, and increase throughput capacity. This paper describes the important features that make this novel separator ideally suited for size classification and density concentration. Test data from heavy mineral, phosphate, and industrial mineral applications are also discussed.

Jan 1, 2005

By Gordon R. Harris, Raymond Chalk

Descriptions of typical pulp and paper manufacturing processes are presented, with particular emphasis on the use of minerals and derived products. Some consideration is given to the future demand for these minerals by the pulp and paper industry. Possible influences of techno-logical change and social legislation are suggested and their effect on saltcake demand by the pulp industry is discussed. Predictions are made regarding trends for new and existing paper products.

Jan 1, 1968

Autogenous-Carrier Effect and Gangue Influence in Fine Particle Flotation of Ilmenite/Titanaugite System

Sep 13, 2010

By Walter C. Woodmansee

The only reported mineral production in 1977 was small output of alluvial gold, valued at an estimated $54,320.2 In addition, marine shells are gathered for use in lime manufacture, although output was not reported. Proposed development of a bauxite mine and smelter, involving Rennell and Vaghena Islands, was deferred in June. Conzinc Riotinto of Australia Ltd. (CRA), in partnership with Mitsui Mining & Smelting Co. Ltd., and the Solomon Government, with- drew from the project, and Mitsui, which conducted a feasibility study and metallurgical testing of the bauxite, decided to defer further work because of slack demand for aluminum in Japan and difficulties in arranging financing. The Mitsui feasibility studies reportedly indicated that the project could be viable despite technical difficulties and relatively high initial investment costs. The project was to produce 1.5 million tons of bauxite and 600,000 tons of alumina per year from reserves totaling 60 million tans at 45% to 50% A1203.

Jan 1, 1981

By Chris D. Shewmaker

So you want to install 2,600 augered cast-in-place piles, about 155,000 lineal feet, in 33 working days? It can be done. The Public Service Enterprise Group (PSEG) decided to build a combined cycle power plant in Lawrenceburg, Indiana. PSEG selected Fluor Constructors Indiana, L.P. to design and build the plant. Fluor Constructors, in turn, selected Richard Goettle, Inc. to install the piles. The initial plan was to install the 2,600 piles in 33 days, working six (6) ten hour days per week. After successfully installing and performing four pile load tests - up to 300 ton capacity - we set out to complete the work and meet the aggressive schedule. After three weeks of installing an average of 75 piles a day with three drill rigs, Fluor relaxed the schedule because we were so far ahead of their projected construction sequence. We elected to continue drilling on a ten-hour day, five days a week schedule. In all, we installed nearly 2,800 piles, totaling 175,000 lineal feet, in about 47 days.

Jan 1, 2004

The Burra Burra Mine is situated in complexly folded Torrensian dolomites and limestones forming the faulted axial region of a major anticline. The orebody mined was largely of secondary origin and confined between two faults, Kingston's on the west and Tinline's on the east. The orebody occurred at the junction between cherty dolomites and a clastic limestone with a large mass of marble breccia along its western margin. Secondary ore consisted of carbonates and oxides in the breccia and the ore bed and detrital copper minerals deposited as part of a clastic breccia in sinkholes and solution cavities in the dolomites and ore beds.Primary sulphides occur disseminated in the marble breccia and in stratiform habit in the ore bed. Kingston's so-called "lode" may be mineralized marble breccia.The marble breccia appears to be of diapiric or sedimentary origin and there is evidence to support a sedimentary origin for some of the copper sulphides. No igneous rocks have been discovered within 20 miles of the mine and any hydrothermal activities were probably at comparatively low temperature. The possibility of extensive stratiform and disseminated copper sulphide mineralization in the marble breccia and ore bed requires testing by further drilling and geophysical surveys.INTRODUCTIONThe re-interpretation of Burra Burra geology and ore formation discussed in this paper resulted from a comprehensive investigation of the mine and its surrounding district begun in December 1961 and in progress at the time of writing. (February 1963). The decision to investigate Burra Burra was taken after a thorough examination of records and reports of all non-ferrous metal deposits throughout South Australia and was given impetus by a report by Thomson (1963) suggesting a sedimentary origin for the copper mineralization. Although the author does not concur fully with Thomson's interpretation there is no doubt that sedimentary processes have played an important part in the formation of the Burra Burra copper deposit, nor is there any doubt that igneous activity played no part.

Jan 1, 1963

By Russel Delmar

Construction of Ontario Power Generation?s 12.8-m diameter, 10.4-km long water diversion tunnel in Niagara Falls, Ontario, is underway. The tunnel is being excavated by means of a 14.44-m diameter open gripper Tunnel Boring Machine. The tunnel lining is constructed as a two-pass system with the initial lining consisting of rock bolts, mesh, steel channels or ribs, and shotcrete, and the final lining consisting of pre-stressed cast-in-place concrete with a waterproof membrane. This paper describes salient design and construction aspects as follows: ? Regional and Site Geology ? Tunnel Layout and Design ? TBM Tunnelling and Cast-in-place Concrete Lining Construction

Jan 1, 2008

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By Xinhua Wang, Qiangqiang Wang, Yubin Li, Shusen Li, Lifeng Zhang

"Numerical simulation on the fluid flow in a Flow-Control Mold (FC-Mold) were performed. The motion of inclusions were calculated. With FC-Mold, the flow pattern and surface velocity become more symmetrical, and at higher casting speed the velocity of liquid steel in the top region of the mold was largely reduced with the highest velocity of the meniscus reducing from 0.65 mis to 0.4 mis, and the meniscus shape became flatter. With FC-Mold, more inclusions approached to the surface of the slab and the amount of inclusion in the center of mold became fewer. Larger inclusions were easier to remove, however, the EM filed of the FC-Mold could hardly improve the removal of inclusions from the molten steel.IntroductionElectromagnetic brake technology is an effective method to control the flow pattern within continuous casting mold, together with other casting parameters, nozzle design and mold geometry [1-5]. Due to the interaction between the applied magnetic flux and the conductive molten steel inside the mold cavity, a force is generated in the direction opposite to the jet flow, which can decelerate the high speed steel jet from the SEN ports. The potential benefits include fewer surface and internal defects, fewer inclusion especially at higher casting speed. However if used imperfectly, electromagnetic forces can have opposite effect [6]. Numerical models are the best tool to optimize electromagnetic flow control. In the current study, numerical simulation was performed to investigate the flow field in a continuous casting FC-Mold, and the effect of different operation parameters on the flow, surface level and velocity in FC-Mold were discussed."

Jan 1, 2013

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By Gordon M. Miner

When I was originally invited to speak to this audience on the subject of the future supply of precious metals I was somewhat apprehensive and suggested that the Program Chairman select someone with more credentials. He declined and the results of our conversation gave me cause to reflect and recall the opportunities I have had over the years and how fortunate I have been to be associated with so many successful companies and knowledgeable people affiliated with the precious metals field. I discovered that since 1935, 1 have worked in or visited most of the gold and silver camps in the United States; have been a leaser of a gold mine in Mohave, California; have both lost and made money in the silver futures market; have worked for two of the greatest precious metals companies in the United States - Homestake Mining Company and Hecla Mining Company, have spent a considerable amount of time in precious metal related discussions with men like Don MacLaughlin, Paul Henshaw, Dick Stoehr, Abe Shoemaker, Bill Love, Phil Lindstrom, Simon Strauss, Herbert and Bunker Hunt and many others. It is those exposures and experiences that I draw onto discuss the subject at hand.

Jan 1, 1980

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966