Search Documents

By J. A. Hayes

For over a decade the Osterberg Load Cell has been successfully used to determine the shear capacities of drilled shafts. Since the test method measures side shear directly, analytical complications due to the influence of end bearing resistance are removed. The data suggest that the side shear component of a drilled shaft's capacity is often more significant than end bearing. Given the interest in the use of side shear in drilled shaft design in compressible materials, it is important to examine factors that can influence capacity. We have found that some factors widely believed to influence capacity, such as slurry type, are not as important as commonly thought in most materials. Factors that are not usually considered as important, such as casing use, hoop spacing, concrete slump, concrete additives, spacers and rebar clear cover, seem to be more influential with respect to side shear capacity. For example, substantially lower than predicted shear resistance can occur when the rebar clear cover is small with respect to the cage diameter. We observe this most often in fine-grained cohesive soils. This effect can be exaggerated if the rebar cage has tight hoop spacing, if the concrete has low slump and if the hole is not straight. We have also noted that improper use of temporary casing can have a dramatic effect on side shear resistance. In some cases we have observed tested shear capacities reduced to less than 5% of either predicted or available shear values.

Jan 1, 2003

By Paul Harvey

Following initial discovery in 1991, BHP Billiton Diamonds Inc opened Canada?s first diamond mine, the Ekati Diamond Mine TM (Ekati) in the Northwest Territories on October 14th, 1998. Four short years later on November 29th, 2002, saw the opening of North America?s first underground diamond mine - the Koala North mine. Nestled between the original Panda open pit and the new Koala pit which is in the early stages of production, Koala North represents the only underground kimberlite mining venture in arctic conditions outside the new underground mines being developed by ALROSA in the Yakutsk region of eastern Russia. Extensive underground kimberlite mining has been practiced in the Republic of South Africa for much of the 20th century and continues today. Underground mining represents a key component of the long term business plan for the Ekati. As various open pits reach their economic limit, continued recovery of high value ore at depth is dependent upon the ability to productively mine the kimberlite pipes by underground methods. As a function of its location, size, and value, the Koala North pipe is ideally positioned to host the first underground mine at Ekati . In addition to being a production source for the operation, Koala North is designed as a learning mine, from which to gain valuable experience in preparation for the potential mining of other larger, higher value pipes by underground methods in the future. Fortuitously Koala North was available for development so the learnings could be integrated into the Panda mine design prior to completion of the Panda pit. Establishing our first underground diamond mine, and applying the open benching mining method in arctic conditions brings a unique combination of mining challenges together in a harsh climate and remote environment. This paper examines the design and establishment of the Koala North mine. Discussion includes experiences gained from the first year of development, production start-up, and provides a brief overview of our potential underground future at Ekati .

May 1, 2003

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

By Cornelius F. Kelley

DURING the war, events moved with unprecedented rapidity. Situations, industrial, economic and financial, arose over night that stressed to the uttermost the ingenuity and ability of those who dealt with them. It was essentially a time demanding action rapid and concentrated, and not one for discussion, either academic or polemic. As a result, matters of importance were necessarily transacted without the desirable opportunity being afforded of enabling a general understanding to be gained as to the relative merit or demerit involved, and in some instances, legislation essential to enable the consummation of an important matter was passed without attracting the public attention then deeply engrossed in the larger aspects of the situation. The result was that so long as the public mind was occupied, little or no concern was given to questions that ordinarily would have invited immediate attention; and in some instances, only when as an aftermath of war a particular subject has become a matter of discussion, criticism not altogether fair is made without first obtaining accurate knowledge as to the conditions that prevailed, the purpose sought to be accomplished, or the results obtained by the action taken.

Jan 1, 1921

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

Influence of Grinding Media on the Flotation of Carbonate Using Sodium Oleate as Collector

Sep 13, 2010

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

By John Hanna

Recently. researchers at The University of Alabama have developed a two-step method for the treatment of phosphorus sludge that includes bulk removal of phosphorus by physical separation techniques followed by remediation of the residual P4 in the sludge using a novel wet air oxidation technique known as "HSAD", Tests made on samples of the electric furnace phosphorus sludge have demonstrated that essentially complete and fast removal of the P4 in the sludge can be achieved by the HSAD wet oxidation treatment, Further studies were made to determine the applicability of the two-step process on sludges of various origins. P4 contents different pre-treatment and storage conditions, The present work discusses the mechanisms and factors controlling the HSAD wet air oxidation remediation approach.

Jan 1, 1992

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

By Michael L. Jones

Outline ?Background ?Identify and quantify CO2 sources ?Consider options for CO2 separation and capture ?Review options for sequestration/reuse ?Determine best option for managing CO2

Jan 1, 2008

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003