Search Documents

By AIME AIME

The first Diesel-electric locomotives for the Mesabi iron range of the Lake Superior district were put into service last summer by the Oliver Iron Mining Co., U. S. Steel subsidiary. There were ten of these locomotives, rated 1000 hp. and weighing 125 tons each. They are designed for service from 16 to 24 hours per day to haul trains of loaded ore cars from open-pit mines, 200 to 400 ft. deep, on a two to eight-mile haul to the top of the pit. The locomotives push or pull the trains over switchbacks and up heavy grades with 5 per cent maximum against the load. High tractive effort, less smoke, and ability to negotiate sharp curves were among the reasons for the selection of Diesel-electric locomotives.

Jan 1, 1941

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By Steve Dillingham

Whenever misfired holes or portions of misfired holes remain after a blast is fired, a hazardous situation exists until the unfired explosive materials have been disposed of properly. Yet, there are so many factors that can contribute to misfires that it is impossible to give blanket instructions on how to handle them. To complicate matters, misfires today are rare due to reliable blasting products. As such, it isn’t very surprising that many blasters have never had to deal with a misf i re condition. While the likelihood of a misfire occurrence is minimal, you should always be pre p a red to handle a misfire should you be involved in such an event. To begin, every blaster and blasting org a n i z a t i o n should develop a misfire policy which contains the company’s safe operating pro c e d u res, emergency contact list, as well as any regulatory compliance re q u i re m e n t s . Tailgate and/or company-wide safety meetings should communicate the company’s contingent misfire pro c ed u res and any special site-specific precautions BEFORE the start of any project.

Jan 1, 2004

By Richard Crockford

The World Trade Center (WTC) is located on the west side of Manhattan in New York City, approximately 0.5 miles north of Wall Street, and is owned and operated by the Port Authority of New York and New Jersey (PA). As part of the WTC site redevelopment the New York City Transit Authority?s No. 1 subway line which runs through the site below grade, was underpinned so that the soil beneath it could be removed along with the rest of the new east basement excavation. Consequently a scheme comprising micropile installation through and around the existing subway box was designed. The subway had to remain in use throughout save for planned weekend outages to allow a portion of the underpinning to be fitted through or on to the existing structure. At times this involved accessing and drilling from within the subway tunnel under short General Order (GO) Subway shutdown periods. At either end of the subway passage through the WTC site jet grout underpinning was designed to provide support and to complete the excavation and construction of the east basement wall in the areas beneath the subway where it was impossible to install a slurry wall. The jet grout blocks thus formed had to be largely installed around the clock during 53 hour long GO weekend outages and had to overcome severe logistical constraints in and over the tunnel. The jet grout blocks had to provide strengths of at least 500 psi at 3 days and 700 psi at 28 days. The jet grouted soil mass also had to have a level of permeability less than 0.03 feet/day (1 x 10-7 m/s). After an extensive trial program and then production testing it was concluded that the glacial till above the rock proved to be a particularly difficult soil strata to collect test data from and hence the level of observational monitoring was increased to progress the excavation works. Throughout the installation of micropiles and jet grout columns extensive monitoring was in place and prompted a variety of working method changes. The work described in this paper was performed by the Nicholson Construction Company/EE Cruz Joint Venture.

Jan 1, 2008

By I. Gombköto, G. Földing, G. Mucsi, B. Csoke, J. Faitli, B. Kovács

This paper summarizes the main achievements of our previous project entitled "Development of a technological system producing quality guaranteed fly-ash based binder". Furthermore, this study deals with the laboratory experience of lignite fly ash utilization for two different goals. On the one hand the fly ash was tested as a binder; on the other hand it was investigated as an underground mine backfill material. Considering the first goal, the utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of relationship between the degree of activation of fly ash and the strength of the obtained concrete. The results confirmed that this hydraulic binder is suitable for construction of stabilization and capping layers or base layer. Regarding the backfilling application, this paper presents laboratory experiments, their results including settling tests, hydraulic permeability and strength measurements and dense slurry technology related results.

Jan 1, 2011

By K. Yamaguchi, Sekimoto. H.

"Platinum Group Metals (PGMs) used as catalyst which reduces toxic substances in emission gas exhausted from an automobile should extensively be recycled because they are rare metals produced only at the limited regions. The recycling process is to smelt an alumina honeycomb, in which PGM is built, in molten iron with flux such as lime and silica to separate them. PGMs are concentrated in molten iron while alumina in slag.The objective of this study is to understand the factor to concentrate PGMs in liquid iron as much as possible. Fundamental research of the distribution of the PGMs between the slag and liquid iron was carried out to recover the value metals of platinum, palladium and rhodium from the three-way auto catalyst. The distribution ratios of platinum, palladium and rhodium between the Al2O3-CaO-SiO2 slag and liquid iron are from 10-6 to 10-5, and these are concentrated in comparison with slag phase by about 1 million times to the liquid iron at 1873 K. The distribution ratios of platinum between the FexO-CaO-SiO2 slag and liquid iron decrease from 0.1 to 2?10-4 with increasing the CaO content in the slag. The CaO addition to the FexO unary slag is effective in concentrating platinum in molten iron.Based on the distribution ratios obtained in this work, recovery of PGMs was determined. The recovery of platinum, palladium and rhodium increase with increasing the mass ratio, Mmetal/Mslag. In the case of the conditions of Mmetal/Mslag = 0.04, the recoveries of PGMs showed more than 99.97%. The use of liquid iron and carbon saturated liquid iron as the collector metal is advantageous for the PGM recycling of the three-way auto catalyst. We found that PGMs are enriched to the molten iron or the carbon saturated iron and the slag loss of PGMs is negligible small."

Jan 1, 2014

A unique sluicing process for recovering tailing impounded in a valley was developed by Electrolytic Zinc Company of Australasia Ltd., West Coast Mines, Rosebery, Tasmania.Earthmoving equipment could not be used as most of the material to be recovered was semi-fluid. A conventional sluking method was also impracticable as there was no suitable working face from which the process could be commenced.Operations started from a flat surface, using special techniques for sinking through the tailing and establishing producing working faces as the sinking process continued.After about 2 years the bottom of the dam was reached and conventional sluicing methods could be used.

Jan 1, 1973

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By J. Kang

To obtain microbial cultures with the ability to efficiently leach copper ion from chalcopyrite, microbial samples from acid mine drainage sites were mixed and then subjected to mutation using sodium nitrite (NaNO2), diethyl sulfate (DES), ultraviolet light (UV) and their combinations. Mixed cultures with a much stronger ability to leach copper ion (identified as mixed cultures A, B, C, D and E) were obtained by screening on leaching media. Leaching tests showed that mixed culture E had the best leaching performance and increased the Cu2+ content by 120.5% in 20 days, compared to a control without mutation treatment. Mixed culture E grows well on Leathen leaching medium supplemented with Cu2+ (at a final concentration of 32 g/L), reaching 3.2 × 107 cells/L after 15 days, while the unmutated control culture cannot survive beyond 15 days, indicating that mixed culture E is more tolerant of high concentrations of Cu2+. In addition, continuous leaching by mixed culture E is very effective at a pulp density of 1%. These results suggest that it has the potential for industrial applications.

Jan 1, 2008

By André van Wageningen

Long term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. In current mining operations, it is important to report changes in long term plans as soon and as accurately as possible. Where geological data can change rapidly, such as in narrow vein deposits, the need to quickly identify and optimize different long term alternatives becomes a difficult task and can lead to many permutations of the long term mine plan. The question arises, is the new plan optimal or not? Can the company objectives be met while adhering to operational constraints? Although a number of optimization techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimization techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the possible permutations. The GA itself contains very little problem specific information and, as such, in this study, has been linked to a discrete-event simulation (DES). The DES is able to evaluate each sequence proposed by the GA and determine the effectiveness and value of each schedule. The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimization process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GADES module is then used to ?optimize? a narrow vein theoretical case study and the results discussed in a broader mining context.

Oct 1, 2004

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By Joel Darmstadter

The position of the coal industry in America’s fuel and power picture remains one of prime importance. Measured in Btu terms, the industry is the country’s leading energy producer and an important exporter. Foreign coal sales yield annual proceeds of about $4 billion. Coal’s one-fifth share of the nation’s energy consumption is nearly as high as that of natural gas. Coal is the electric utility sector’s principal fuel supplier. It accounts for about55% of the electricity generated at power stations.

Jan 1, 1999

By A. K. Mukherjee

The roles of pulsating mechanisms such as the amplitude and frequency of the jig cycle are well established in jigging. Also well established are the roles of the size ratio and the volume fraction of the feed. In iron ore beneficiation plants, these process parameters are optimized to achieve the highest efficiency. However, the role of one of the more important feed characteristics, the liberation characteristic of the feed, has not been studied in detail. Evaluation of the liberation characteristics is difficult because the required washability test is not viable for iron ore feed. In this paper, a new method is proposed in which the liberation characteristics are measured through a separation efficiency value. In the new evaluation method, jigging parameters such as amplitude and frequency of the jig cycle are optimized from the fundamental understanding of the process dynamics and feed characteristics such as size distribution. Then, feeds with different liberation characteristics are tested to evaluate the liberation characteristics of feed in jigging.

Jan 1, 2008

By A. Kostin

GIS and multivariate geometric distribution have been used to predict the association of high-level intrusives with hydrothermal alteration related to iron oxide Cu-Au (IOCG) mineralizing systems. Several examples in the Russian northeast are presented in this paper. IOCG ore deposits can have enormous geological resources containing significant reserves of base, precious, and strategic metals, and hence are economically attractive targets for mineral exploration. To date, examples of this type of mineralization have not been reported from the northeastern area of Russia. The Tarinskiy ore cluster, located in Eastern Yakutia, shows brecciated altered rocks with sulphide and iron oxide cement, which is typical for IOCG mineralization of the iron oxide Cu-Au±U type. This cluster was formed near surface and is linked with the Rep- Yuruinskiy pluton. It has potential to host new world-class precious metal deposits in northeastern Russia

Jan 1, 2014

By G. M. Carrie

Introduction The subject of basic refractories is daily becoming of increased importance in metallurgical processes, and there is a constantly growing necessity for the development of better materials. This fact, together with the realization that Canada possesses one of the best sources of such refractories in the British Empire, if not in the world, made it appear? advisable that the subject be presented to the Empire Mining and Metallurgical Congress at the 1927 meeting. Having been in close touch with developments in the Canadian product during the past five years, G. M. Carrie was requested to prepare such a paper. The Canadian producers of magnesia refractories have succeeded in developing the product to a place where it has almost entirely displaced imported materials from the Canadian market. These developments were made possible by a close study of the methods of preparation of the material, and by an exceedingly careful control of the manufacturing process so as to obtain a thorough blending of the different constituents with the resultant uniformity of composition. This point is very important to the metallurgist, as un-uniform materials are a potent cause of difficulties in most manufacturing processes and the constant trend is towards their elimination. The temperature at which the Canadian material is burned ensures high specific gravity and thorough shrinkage. The grain size of the product is so controlled that the voids are only just sufficient to allow of proper bonding, thus making possible a dense, hard bottom affording high resistance to erosion and shock. Careful proportioning of the constituent elements absolutely prevents disintegration.

Jan 1, 1927

Project Located in northwestern British Columbia 70km West of Cassiar Highway Galore Creek Project and Road Access Corridors Designated For Mineral Development in Stikine-Cassiar Land Resource Management Plan (LRMP)Approved in 2000Strong BC Government, local community and Tahltan First Nation Support for Project

May 1, 2006