Search Documents

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By R. G. Burdick, W. R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abondoned coal mines also imposes potential hazards in current underground mining operations, since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive manmade tunnels in previous work has led to the development of a surface-operated automatic earth resistivity survey system and associated computer data reduction process for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to-diameter ratios greater than 10 to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting abandoned coal mine workings. The hardware and software aspects of third new system are described together with applications of the method for surveying and mapping abandoned coal mine workings. Field tests are presented to illustrate the detection of both air-filled and water-filled mine workings.

Jan 1, 1984

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

By Henry S. Washington

I. INTRODUCTION. DURING the last twenty years or so the chemical investigation of rocks has made great advances, and it is now generally recognized that a knowledge of the chemical composition is as essential as that of the texture or mineral composition-if not more so-for the proper classification of rocks and study of their origin and relationships. Rock-analyses have vastly increased in numbers and, what is of greater importance, in quality. New and improved methods permit of greater accuracy than was possible in the early days, and the list of chemical constituents frequently determined has risen from the seven or eight of the greater part of the nineteenth century to twenty or more. Indeed, rock-analyses with determinations of so many constituents are now commonly made by the chemists of the United States and Australia, while in Germany, Great Britain, France, and Italy the rarer constituents are determined more frequently than formerly. As a consequence of this modern, accurate work, it has been discovered that some elements which were formerly supposed to be rare are of wide-spread occurrence and are often present in considerable amount. The fact is further being developed that the elements tend to show certain relations of occurrence or abundance in connection with each other. This is a fact which is applicable to the rarer elements, and which also finds a broad geological and petrological expression in the recognition of petrographic provinces. We are beginning to obtain some definite, though as yet rudimentary, knowledge of the distribution of the elements among igneous rocks. Some of the results along these lines obtained by study of the vast accumulation of analytical data now available are well known to petrologists, while others do not seem to be so gener-

Sep 1, 1908

By Tad S. Golosinski

The paper describes Online Master of Engineering Program at the University of Missouri-Rolla and discusses the experience gained during the first three years of its offering. This innovative educational program is designed primarily for mature students with an engineering or science background who want to acquire or upgrade their knowledge of mining engineering. Students can specialize in several different areas of mining, such as surface mining, underground mining, mine environment and the like. All courses constituting the program are taken online, through the Internet, without the need to attend the UMR campus in person.

May 1, 2004

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region's product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Michael J. Brown

It is often necessary to undertake some form of pile testing to verify design calculations. Historically this has been limited to static and dynamic tests. Newer rapid testing methods such as Statnamic are seeing more frequent use. This form of testing can be advantageous due to short set up time and test duration. Although the methodology suffers from a lack of formalised guidance and may prove difficult to analyse in certain soil conditions. This paper investigates the suitability of Statnamic testing and analysis for a range of soil and pile types as well as different installation methods through a number of case studies undertaken in the UK. Recommendations are made on test specification and analysis.

Jan 1, 2006

By John D. Godfrey

Geological mapping on the Canadian Shield in northeastern Alberta outlined severalgranitoid rock massespotentially suitable as building stone. A particularly attractive prospect, the Chipewyan Red Granite, was subjected to an aerial survey and ground check. The petrologic and fracture characteristics critical for quarrying and use as a building stone were assessed in the course of detailed mapping at two of the most favourable sites. The extension of good rock was tested to shallow depths at one site by shallow diamond-drill coring. , The Chipewyan Red Granite displays a warm red colour, medium grain size and fairly massive texture, and takes a good polish. Deleterious geologic features studied in outcrop and subjected to structural analysis included regular joint systems, quartz veins, pegmatite dykes, basic shear zones and fault zones. Many of these key geologic features are systematic and hence predictable for stone quarrying purposes; other features, such as irregular fracelM tures, are non-systematic and arefar less predictable. The megascopic structural features studied show similar preferred orientations which appear to be collectively related to the tectonic history.

Jan 1, 1979

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

By L. Obert, D. E. Stephenson

The objectives of this investigation were to develop a laboratory procedure in which core discing could be produced under known (and variable) stress conditions, and to study the discing characteristics of several fypes of rock. Discing of rock cores refers to the formation of discs or wafers of relatively uniform thickness which fracture or rupture on surfaces approximately *Fracture is a type of failure in which there is a complete loss of cohesion and fresh surfaces are created. Rupture is a type of failure in which there Is only a partial loss of cohesion. normal to the axis to the core (see Fig. 1). Usually the surfaces of the discs are concave-convex with the concave side toward the collar of the hole. The surface of the fractured discs are like those created by a tension failure (or possibly a shear failure with virtually no normal compressive stress). This phenomenon has been observed by a number of investigators1-5 in the course of diamond drilling in underground mines, especially in areas suspected of being under high stress. The state of stress in the core required to produce discing is not exactly known. Tranter and craggs6 theoretically investigated the stress distribution in an infinite cylinder, subjected to hydrostatic pressure, minus p, from z = 0 to z = 8 and unloaded from z = 0 to z = 8, Fig. 2. The exact solution to this problem shows that a tensile stress develops in the loaded region near z = 0 with the greatest tensile stress on the axis of the cylinder. A tensile stress also developed on the surface of the cylinder at a point just outside of the loaded zone. Jaeger and Cook3 experimentally investigated the discing mechanism by biaxially loading cores in a pressure jacket sealed at the ends by O-rings. According to the Tranter and Craggs theory it would be expected that failure should occur at the pressure discontinuity at the O-rings. The experimental results showed that if the specimen was unjacketed it broke at random points within the pressurized zone and at a pressure somewhat greater than the tensile strength of the specimen, presumably due to the development of a

Jan 1, 1965

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

The Golden Cross Mine will be the first underground gold mine in New Zealand to operate since 1952. The development plans, along with the conditions and circumstances presently found in the now ongoing mine development, will be discussed as well as a brief review of planned stoping activity and stoping results to date.

Jan 1, 1991

By M. Moseki

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy of Materials) degree This paper presents the research into melting of scrap for job creation purposes in rural areas. The research was done on behalf of Mine Recycling Services (MRS), the company that will implement the project. The project involves the research into available cost effective and easy to operate technology. The paper covers the experimental and theoretical work that was conducted. The results were used to determine the best equipment and method for melting and casting brass scrap.

Jan 1, 2002

Titanium and Zirconium Industries Pty. Ltd. separates rutile and zircon from heavy mineral concentrate recovered from sand dunes on the east coast of North Stradbroke Island, Queensland. Separation plant feed is delivered to Dunwich, on the west coast, by a seven mile aerial ropeway traversing the island. Mining and concentration is effected by two floating dredge-concentrators now operating on the beach 31; miles from the aerial ropeway terminal. Heavy mineral concentrate is transported hydraulically from the dredges to the ropeway through a 6 in. pipeline. Six pumps in series deliver 24 ton/hr of dry solids in a pulp containing 13 per cent solids. For maximum economy the transfer pumping system is controlled deliberately to cause transportation in the zone of incipient settlement of solids, ieat velocities below the limit deposit velocity for the particular pipe diameter, pulp density, and specific gravity of solids. Automatic density control, based on a combination of power consumption and pipeline pressure, eliminates the danger of plugging the line but periodic flushing is necessary to remove gradual accumulation of solids in the bottom of the pipe. After 15 months operation the pipeline was descaled with hydrochloric acid to remove severe blistering with rust nodules, regrowth of which is now prevented by continuous injection of inhibitors. After transporting 100,000 tons of heavy mineral the average wear on the steel portion of the pipeline was 0·01 in. and indications are that wear on the asbestos cement portion is less.DESCRIPTION OF OPERATIONSGeographyTitanium & Zirconium Industries Pty. Ltd. (T.A.Z.I.) operates on North Stradbroke Island, some 30 miles southeast of Brisbane, Queensland. The island is approximately 25 miles long and eight miles wide, and is bounded on the east by the Pacific Ocean and on the west by Moreton Bay (Fig. 1). With the exception of a small outcrop of volcanic 1. Manuscript received at The Institute. 8th May. 1962. This paper was presented at the Annual Conference of The Institute. 5th-11th August. 1962.

Jan 1, 1962

By Miller F. S

The famous Golden Mile of Kalgoorlie in Western Australia was, between 1888 and 19ft, one of the richest and most important gold camps in the world. Annual production, which reached a peak of nearly 1,300,000 oz. in 1903, however dropped to below 400,000 oz. after 1920.Depression seized the camp, and many mines closed down. The output from this old field is now steadily mounting under the stimulus. of a higher price for gold. In 1935 300,000 oz. of precious metal were recovered and the future is bright. Total production from the field is 21,400,000 oz., whereas something like £23,600,000 have been paid in dividends.The Golden Mile has been studied by many geologists. Their somewhat diverse findings were published for the most part in the Australian technical press which, unfortunately, is not sufficiently represented in foreign libraries.The following article is based on an eighteen months' study in the district for Gold Mines of Kalgoorlie Ltd., preceded by four years' experience with almost identical rock types in the, Porcupine district of Ontario. The excellent record of observed fact left by previous invesigators, augmented by talks with observant mining men...

Jan 1, 1937

By W. H. Schiffbauer

The protection of miners, equipment, and infrastructure is discussed. While the primary focus of the described technology is to prevent miners from being injured, struck-by, or crushed by heavy equipment; another major benefit realized is also the protection of equipment and infrastructure. An attempt is made to define and classify the systems used to provide proximity detection and warnings as well as collision detection and avoidance. Information about the speed of vehicles and human operator response time can be a factor in the choice of what type of system and what features are needed to properly address the needs. How the technology adjusts to compensate for various vehicle speeds, while maintaining the same level of protection is noted. The statistics which justify the need of miner protection are provided. The primary system components required, what attributes they feature, and how they respond in the environment, is briefly highlighted. The physics behind the danger zone marker technology and what makes it so robust and reliable is established. Examples of a few mining applications and specific operational modes are provided for both surface and underground.

Jan 1, 2011

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By A. Meek

This report compares the compressed air driven rocker shovel to the newly developed Warthog Non-throw development end loader. The two machines were compared on aspects such as safety, loading potential, energy efficiency and costs. The objectives of the comparison were to determine whether or not the replacement of the rocker shovel with the Warthog will be operationally and financially justifiable. The results from this study were obtained from underground observations and time studies on the machines, as well as consultations and data collection at the shaft and suppliers. This paper compares only the Warthog loader to the Trident 215 rocker shovel used at Anglo Platinum?s Brakspruit shaft and does not compare the other models of rocker shovels, which are fundamentally the same but will have different loading potentials and specifications. Cleaning times for the rocker shovel are based on underground observations at Brakspruit shaft. These times can be influenced by factors such as blasting practices, compressed air pressure and operator experience and skill. For this reason the times will most likely vary at different shafts. The Warthog cleaning times are based on manufacturer specifications and results from trial stages and therefore further work is required to confirm cleaning times achieved.

Jan 1, 2009