Search Documents

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By L. Mabiza

Keywords: Pyrometallurgy, furnace, sulphur, SO2, off-gas, Zimplats Zimplats embarked on an off-gas sampling campaign in December 2009 to characterise the concentration of SO2 in the off-gas from their 13 MW furnace. In excess of forty isokinetic samples (US EPA Method 8) were taken over seven days. The aim of the sampling campaign was to increase the understanding of factors that influence sulphur release from sulphide concentrates in an electric furnace. Specifically, detailed monitoring was conducted over various operating conditions to evaluate: ? The relationship between SO2 and feed rate (i.e. furnace power) ? The relationship between SO2 and ingress (i.e. furnace freeboard pressure) ? The impact of concentrate bed thickness on SO2 (i.e. blacktop) ? The effect of events such as tapping and converter slag return on SO2 ? The desulphurization reactions that take place in the blacktop A model was developed to predict the SO2 content in furnace off-gas for a particular set of operating conditions. In order to evaluate the impact of random, uncorrelated changes in concentrate composition, ingress and power (feed rate) on the SO2 content of the off-gas, a Monte Carlo approach was adopted whereby concentrate composition, power, and ingress were allowed to vary randomly around selected set-points. The model is primarily based on the release of ?labile? sulphur from the partial thermal dissociation of sulphide minerals with an over-stoichiometric sulphur content (e.g., Fe7S8 decomposition to FeS and S). The main findings of this work suggest that labile sulphur does not fully account for the measured SO2 content of the off-gas, and that limited oxidation of sulphides during melting also contributes to the SO2 content. Details of sulphide oxidation reactions in the furnace remain unclear, and it is currently not possible to provide a theoretical framework for the relationship between the extent of oxidation and variables such as temperature, gas composition, particle size, and residence time in the furnace black top. Through the use of the Monte Carlo model it was, however, possible to constrain the extent of sulphide oxidation to about 1%. This work has shown in practice what was expected in concept, that SO2 in off-gas is proportional to furnace power and ingress rate. The model that was developed consistently slightly under-predicts the quantity of SO2 generated. It also highlights that more work is required to better understand the analytical methods used to analyse for SO2 in off-gas.

Jan 1, 2011

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonites to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath, 1986 and personal communication). These bentonites typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X¬ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated" bentonite to the oilfield since specifications are

Jan 1, 1989

By Pengfu Tan

A thermodynamic model has been developed to predict the distribution behaviors of Cu, Fe, S, O, Pb, Zn, As, and heat balance in a lead blast furnace. The modeling results have been validated by the plant data of a lead smelter in Asia. The model can be used to predict for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen-enriched air. The effects of the blast air, industrial oxygen, and coke charge on the distributions of Cu, Fe, S, O, Pb, Zn, As, and heat balance, and on the lead loss in slag have been presented and discussed.

Jan 1, 2005

This Bureau of Mines publication presents an overview of mine electrical power systems research currently being conducted by the Bureau. The papers, given at a Technology Transfer Seminar, emphasize the increasing importance of research related to the safety considerations of underground coal mine electrical systems. Selected topics are included that summarize results of research in the areas of electrical shock prevention, explosion-proof enclosures and load centers, discriminating circuit breakers, and trailing cables. Other topics discussed at the seminar are published as separate sections of the Bureau of Mines Hand- book "Application Notes--Mine Electrical Power Systems."

Jan 1, 1982

By B. B. Dhar

Slope stability at the proposed mine in Rajasthan was analysed in two dimensions using a finite difference code. The properties of the rock material were determined in the laboratory and subsequently modified to approximate those of the in situ rock mass. Geotechnical mapping was undertaken to determine the critical orientation of structural discontinuities. The results of the work indicated that an open pit 148 m in depth would be stable with overall slope angles of 60 degrees

Aug 1, 1994

By Prosper Lamothe

El presente texto describe la metodología ad-hoc para evaluar proyectos de Inversión estratégicos a través de la flexibilidad y la teoría de opciones reales. La clave de dicho enfoque metodológico radica en realizar la mejor proyección del precio de los metales aplicando las mejores prácticas mundiales al respecto. Para ello, se analizan una gran variedad de modelos concluyendo que el mejor modelo a aplicar, debe ser la simulación del precio del metal con reversión a la media con saltos de tipo aleatorio.

Sep 9, 2007

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By Madgwick J. C

Four manganese dioxide leaching microorganisms, an Achromobacter spp, Aspergillus niger, Elllerobacter cloacae and Elllerobacter agglomerails were purified from sucrose enriched crude mixed cultures which contained at least sixteen, non-leaching, morphologically different, colony types. Fastest leaching rates were obtained from the original enrichment's mixed cultures (1.26 g Mn++ I/d) while best yields of Mn++ m terms of sugar use came from Achromobacter and A. niger being 0.84 and 0.89 g Mn++/g sucrose respectively. The peak efficiency in manganese reduced, per carbohydrate used, coincided with the exponential growth phase for Achromobacter. The two Elllerobacter species performed better in stationary or senescent growth phases.

Jan 1, 1985

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By R. G. Dressler

The Federal Bureau of Mines designed, constructed, and operated a demonstration plant at Louisiana, Mo., to produce gasoline, liquid fuels, and organic compounds from coal by a modified Fischer-Tropsch gas-synthesis process. Satisfactory equipment was developed to produce and purify synthesis gas and convert it into the desired products. Coal or coke was gasified with oxygen and steam to make a gas consisting essentially of carbon monoxide, hydrogen, and carbon dioxide. Dust in the raw gas was removed by cyclone separation, water scrubbing, and electrostatic precipitation. Carbon dioxide, hydrogen sulfide, and organic sulfur were removed with diethanolamine, iron oxide, and activated carbon. The gas was passed over iron catalyst and was converted into synthetic liquids, which were then separated and fractionated into gasoline, diesel oil, other liquid fuels, and oxygenated organic compounds. A 39-day continuous run demonstrated the feasibility of the process. Addition of 3 milliliters of tetraethylead per gallon of upgraded (or finished) gasoline gave a product with an octane rating up to 90 by the research method. After a caustic wash, the diesel oil was of a superior quality; its cetane number was 60 or above.

Jan 1, 1961

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By A. Dale Wunderlich

Since Sept. 11, 2001, the author has been asked by several mining companies and mining publications to share some of his insights on how the terrorist attacks on the World Trade Center (WTC) and Pentagon might affect the mining industry globally. Until now, the author has been reluctant to express his thoughts in a publication that could possibly fall into the hands of terrorists and give them some ideas that they may not have been previously considering. However, the author discussed the contents of this article with several friends and acquaintances in the international intelligence community. They said that nothing commented on here is new to the terrorists. Potential terrorist targets Sources within the worldwide intelligence gathering community have told the author that current intelligence data indicates that it is likely that the Islamic fundamentalist groups responsible for the attacks on Sept. 11, 2001will likely be directing their effort at foreign business entities. Any overseas or any domestic businesses of highly visible companies that are part of the anti-terrorism alliance should consider themselves a potential target.

Jan 1, 2002

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By Rogerio Castejón

The evolution on the computer in the last 10 years have caused a big change on the way the mining companies are doing exploration. The following factors have contributed to that change: the downgrade of computers and software cost associated with the “usability” (easy of use) of the present systems (remember the old DOS and UNIX systems). New systems are more focused on the users rather than on the experts in applications, meaning that the geologist must understand geology and not operational system, programming, etc. Market conditions requires exploration to be faster and more intelligent than in the “old” times, and companies are always demanding quicker answers from their geologist group as well as lower exploration budgets. Exploration teams must be more effective and efficient. In this sense, the only way to achieve those requirements is to use the proper techniques, methods and tools on the diverse stages of exploration. Its necessary to consider that the costs of data acquisition increase, almost exponentially, through the stages of exploration, from grass roots to advanced stage.

Aug 25, 2002

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000