Search Documents

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

By David J. Mack

A SURVEY and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CALCULATION OF YOUNG'S MODULUS FROM THEORETICAL OR EMPIRICAL CONSIDERATIONS Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Southerland (1891), but Fessenden 41,42 made extensive calculations a few years later and arrived at the relationship: [2E = 78. 101 (_L V] where V is the atomic volume. In 1923, Peczalski,43 working from the same stand-point but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: [E=B(m) 2] where B is a constant of value about 8 • 10 7, p is density and m is atomic weight; the atomic volume, of course, being m/p. Portevin44 immediately pointed out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: [E _ KT'Vb] where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson.45 Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff. 50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs.46-48 He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium,

Jan 1, 1945

By Éric Létoumeau, Julie Fournier, Sylvain Caron, Yves Breau, Martin Plante, Dominique Girard, Luc Tardif, François Robichaud

"Since 1999, COREM (formerly the Centre de Recherche Minérale) has conducted and coordinated research and development activities for a consortium of mining companies that uses the benefits and advantages of collaborative pre-competitive research. In particular, COREM’s “In Situ Optimization Group” is involved in the development and implementation of modem information technologies related to process optimization and control.The POP Project was launched in order to increase and consolidate the use of such technologies applied to mineralurgical and metallurgical processes. To ensure a successful transfer to the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM’s members and are grouped into three main modules:- R&D Module: research and development in universities and research centres;-Technology Transfer Module: integration of new tools into the POP Software, industrial applications and technical support;- Training Module: education of new engineers in universities and continuing education of plant personnel through on-site workshops.This paper outlines the opportunities that led to the definition of the POP Project, presents its main objectives and describes its main modules. The main features of the POP Software are outlined, the first applications at COREM’s member plants are presented and, finally, future developments are discussed."

Jan 1, 2002

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By A. W. Bester

Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Eng.) Cullinan Diamond Mine currently handles 3.2 million tons of run of ore per annum. This is done by means of an underground train system, which is located at 763 metre level. Four trains, one in each quarter of the pipe, collect ore from passes and transport it to centrally located tips in the north and south of the pipe. The ore is then split into coarse and fine fractions. The coarse fraction proceeds to the primary crushers in the north and south. Historically, mining has been performed in such a manner that an equal amount of ore has reported to each quarter of the pipe. However, the tonnage profile of the mine will change such that the ore will no longer be split equally. For approximately five years the majority of ore will report to the east and thereafter most of the ore will report to the western portion of the mine. This will continue for the remainder of the current infrastructure level?s operational life. Coupled with this is the fact that the mine is aiming to increase its annual production to 3.8 million tons. The result is that the current ground handling system cannot accommodate the additional tons and therefore alternative ground handling options have been investigated. The continued existence of Cullinan Diamond Mine relies on finding a system that can economically handle the additional tonnage. Three options were investigated. Firstly, a train option, which would be an upgrade of the current system, was investigated. Two truck options were also investigated, the first of which was a conventional truck option. The second truck option was more interesting and involved an unfamiliar Combi truck system. The truck options were investigated primarily due to the fact that the block height of the BA West (a new production block) can be increased by 15 meters if a truck option is decided upon. This would create a significant increase in revenue for the BA West project. Each of the options was assessed in terms of its physical and financial feasibility. In terms of the physical constraints, it was found that all three systems could work. Detailed financial analysis indicated that either of the two truck options would be a suitable solution. However, due to the limited information regarding the Combi truck option, it should be further investigated. This applies particularly to the actual running and maintenance costs for the equipment.

Jan 1, 2005

By Jonathan Peck, Doug Pollitt, Malcolm Scoble

Over the past 5 years the Department of Mining and Metallurgical Engineering, McGill University, has been involved in the performance monitoring of both percussive and rotary drills. Studies conducted in open pit coal and iron ore mines using microprocessor-based research and commercially available instrumentation resulted in the monitoring of at least 6 performance parameters while drilling vertical production blastholes.

Jan 1, 1991

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

In the spring of 1944 the Congress passed Public Law 290 (58 Stat. 190, 30 U. S. C. Sec. 321) "authorizing the construction and operation of demonstration plants to produce synthetic liquid fuels from coal, oil shales, agricultural and forestry products, and other substances, in order to aid the prosecution of the war, to conserve and increase the oil resources of the Nation, and for other purposes." Section 2 reads: "In order to carry out the purpose of this act, the Secretary of the Interior is authorized- (a) to conduct laboratory research and development work, and, with pilot plants and semi-works plants, to make careful process engineering studies, along with structural engineering studies, in order to ascertain lowest investment and operating costs necessary to determine the best demonstration plant designs and conditions of operation;

Jan 1, 1948

By Henry J. Schwellenbach

The New York Trap Rock Corporation has four plants located along the Hudson River, all within 70 miles of New York City. The company produces crushed stone for use as construction aggregate, with a total annual production amounting to 6 million tons. The crushed stone is moved to markets in metropolitan New York, New Jersey and Long island areas by water transportation. There are daily deliveries of approximately 35 scowloads to the market area. Its customers are contractors with ready-mixed concrete and asphalt plants located on the water, where the aggregate is unloaded for its ultimate use. For a number of years capital equipment was replaced only when the current operating machinery was no longer serviceable, or when' a need was apparent for a different type of equipment. There was no particular regard for efficiency or for operating and maintenance costs. Such lack of system often resulted in the emergency purchase of equipment which was later found to be unsuitable for the job. A few years ago it became apparent that a systematic procedure was necessary. After evaluation of several systems, an individualized plan was evolved from the basic pattern developed by the Machinery and Allied Products Institute. The system adopted by New York Trap Rock has proved wholly satisfactory.

Jan 1, 1959

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948

By Dale Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was first attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The configuration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the first four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition.

Jan 1, 2006

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By G. Styles, K. Lye, R. Tenbergen, M. Mayhew

Requirements to produce a higher bulk concentrate grade have necessitated extensive use of on-stream analyser data and computer programming to obtain the targets set for Frood Stobie Mill as required by overall milling considerations.A brief history of milling process changes associated with the changes from a low grade (3% Ni) bulk concentrate in the sixties to a high (6 to 8.5%). Nil bulk concentrate currently will be presented.The heart of the presentation will be the computer control schemes for ""self optimisation"" of the distinct flotation sections in the plant within certain restraints to achieve targets set by the mill metallurgist.

Jan 1, 1985

Gold, silver and palladium may be separated from the other base metals and sulphur contained in copper sulphide precipitates derived from the Sherritt-Gordon nickel process using a process involving an oxidation roast, a reduction roast and a Cu(II)/acetonitrile leach. Sulphur is removed as SO, in an oxidation roast and the hot calcine is reduced with carbon, or with carbon plus cuprous chloride. The resulting product contains metallic copper which is readily dissolved with cupric ions in aqueous acetonitrile solution. Copper powder is recovered by thermal disproportionation. The residue contains the bulk of the iron and precious metals and may be treated by a number of methods, including direct cyanidation or melting with suitable fluxes. Melting the residue will produce a copper alloy containing the precious metals and remove the iron as a slag. The alloy can be recycled to the copper leaching stage or sent for toll refining depending on the precious metal content. Impurities from the leaching circuit are controlled by a bleed circuit which in one approach utilizes the SO, from the calciner to produce Chevreul's salt and separates copper from the soluble cobalt and nickel. Alternatively, the bleed may be directed back to the main refinery copper boil stage or oxydrolysis stage.

Jan 1, 1982

By Fuzail Siddiqui

"The SIDMIN program aims at filling the mineral processor’s need to know the deportment of ‘minerals of interest’ not just ‘elements of interest’ that pass through the processing plants. Generally, chemistry is used as a tool of routine monitoring on site. Mineralogy, which is relatively much slower, is used more as a tool of research and post mortem investigations and these services are usually provided by a distant facility. The SIDMIN program enables site management to receive chemical and quantitative mineralogical reports on their critical samples daily, simultaneously and affordably.The author developed the SIDMIN program at ZCCM Nchanga Division where it continues to be a powerful tool for monitoring the efficiency of operations. Outlines are given of procedures for quick sample preparation and quantification of significant minerals in process samples. A specimen report is presented, which shows the format of reporting the contributions of individual minerals to metal losses at critical stages of the circuit. It is shown that SIDMIN provides timely information to management, about trends and abrupt changes in the quality of ore, and its processing, in a way never achievable by chemical analyses alone. This greatly helps in resolving the age-old problem of ‘bad ore’ or ‘bad operations’ on a day-by-day basis. For example increase in copper mica in the feed indicates excessive ore dilution during mining. Increased loss of free sulphides was traced to insufficient reagent conditioning time at the Concentrator. Persistent losses of leachable oxides at the Tailings Leach Plant were traced to inadequate leach residence time.SIDMIN is affordable because it can be implemented using basic optical microscopes, minimal quantities of micro-chemical reagents and custom trained site staff who demonstrate good colour perception and an ability to follow laid down procedures consistently."

Jan 1, 2000

Resistant Tape A new oil-resistant tape for rapid insulation build-up on splices in large power cables has been announced by Minnesota Mining & Mfg. Co. Designated Scotch brand electrical tape No. 25 is made of synthetic rubber providing greater dielectric strength and resistance to high temperatures. The chemical-resistant qualities of the tape make it suitable for use in oil drilling, mining and underground [ ] cable operations, while the 40-mil thickness and extreme stretch (1500 pct breaking point) make possible smooth insulation wraps on irregular surfaces. Dielectric strength is 15,000 v and 10,000 v at 500 pct elongation. It has an electrolytic corrosion factor of 1.0 and an insulation resistance of 100,000 megohms. Circle No. 1 Hydra-Lift The Pitman Mfg. Co. announces that is now has in production a new model of the Pitman hydra-lift, recently-developed crane with hydraulically-powered boom that can be mounted on the frame of any truck, 1 ½ tons or larger. According to the manufacturer, the new model hydralift model B features a variety of improvements over the original production model, introduced late in 1950. Changes incorporated in the new model, according to officials, not only have resulted in improved crane, but also have given the unit a new profile which distinguishes it sharply from the original model. The two chief improvements in the new model are: a big increase in the unit's safety margin and the fact that it is now shipped almost completely preassembled, cutting the time and cost of installation. Rated capacities of the hydra-lift are based on the tipping factor of a 1 1/2 ton truck, with outriggers down, and thus have not been increased. Circle No. 2

Jan 1, 1952

New Zealand has often been quoted by metallurgists and others as one of the countries in which Tellurium is found, and locally it has been recorded that appreciable quantities of tellurium have been met with in the Thames and surroundingdistricts. However, specimens containing tellurium which have been obtained on this field have not been preserved and their scarcity today points to the fact that tellurium is not here abundant.To ascertain its distribution, analyses and assays have been made by the author on a large number of ores, the results of several of which are given below.The presence of any considerable percentage of tellurium has an important bearing on the metallurgical treatment of ores in which it is found.

Jan 1, 1901