Search Documents

By Aïda Espinola

This work is part of a research program concerning the study of heavy metal removal and selective recovery from electroplating waste waters in the Guanabara Bay ecosystem, preventing the potential noxious retarded effect of landfill, specially in a country of heavy rainfall. A flow-throw cell was employed to adapt to the limits established by the local legislation for disposal in rivers and seas. The cell design is presented and preliminary results show that this cell may be applicable for the decontamination from copper.

Jan 1, 1994

By S. G. Kumar, R. G. Reddy

"Niobium aluminides offer the advantage of higher high temperature capability compared to other intermetallic aluminides due to the refractory nature of niobium. However, the reaction sequence in Nb-Al system is sluggish and currently there is a great interest in the processing aspects of these materials. In the present study, a systematic investigation was undertaken to compare the effect of different powder metallurgy processing routes on the phase relations and microstructure of 66Nb-22AH2Ti (in atom percent) alloy. The three different process routes adopted were: (i) cold pressing followed by reaction sintering; (ii) cold pressing and hot pressing followed by sintering; and (iii) arc melting, hydride-dehydride process to make the alloy powder followed by cold pressing and then sintering. The samples are analyzed by XRD, Optical Microscopy, SEM-EDS and EPMA. The analysis showed that alloy pellets made from pre-alloyed powders i.e., arc melting followed by hydride-dehydride process, gave good densification and more Nb3Al formation.1. IntroductionTo improve the performance standards of turbine engines, materials scientists are challenged to develop materials that have· high thrust-to-weight ratio with high specific strength, high specific modulus and good environmental properties at elevated temperatures. The conventional high temperature materials like nickel based superalloys are high in density and hence many of the high temperature materials scientists have focussed their attention on intermetallic aluminides like Fe-AI, Nb-AI, Ni-AI and Ti-AI in recent years. The phase relations and properties of alloys based on Fe-AI, Ni-AI and Ti-AI are fairly well known whereas little is known about the alloys based on niobium aluminides."

Jan 1, 1996

By D. J. Donaldson

The PAL process for recovering nickel from laterite ore requires large volumes of thick abrasive slurry to be raised lo high temperature (245°C+) and pressure (40 atm.+). Flow diagrams of the process typically result in facilities that have serious operating and reliability problems. Most of the problems can be attributed to using multiple pump stations to raise the slurry to autoclave pressure, large amounts of flash and live injection steam to heat the slurry to autoclave temperature and several steps of flash cooling to lower the temperature and pressure of the abrasive autoclave slurry down to atmospheric conditions. It is proposed that operating and reliability problems of PAL facilities can be mitigated by using Tube-in-tube heat exchangers and "float type" positive displacement pumps. The subject paper describes an innovative application of such equipment in the facility design of the PAL process. Keywords: Nickel, Laterite, PAL, Heating, Slurry

Jan 1, 2004

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999

By John M. Boyle

The use of high vacuum mercury retort recovery as a safe and effective means of removing mercury from mercury hazardous waste solids rendering them non-hazardous and recovering mercury suitable for recycling.

Jan 1, 1995

By C. D. Seybert, J. W. Evans

"The elimination of convection is essential in experimental investigations of diffusive transport (of heat and matter) during solidification. This paper describes an investigation of an approach whereby a magnetic field gradient is applied to a electrically non-conducting diamagnetic liquid. A magnetic body force then arises which is dependent on the volume susceptibility of the liquid and thereby on the density. With the field gradient aligned vertically and of correct magnitude, the variation of gravitational body forces due to density variations (arising from temperature variations, for example) can be counterbalanced by a variation in magnetic body force.Preparatory to a study of convection control in diamagnetic liquids, PN measurements have been made of the convection occurring during the solidification of water. A peculiar flow arises because of the density maximum at 4°C. Modeling of the flow the steady-state solidification of water in an extremely high field magnet at the NHMFL indicates that flow can be significantly reduced, but it is suggested that, due to field gradient variations within the cell, flow cannot be completely halted. INTRODUCTIONNatural convection is inherently a part of terrestrial solidification. Density-based convection during solidification, due to gradients of temperature and/or concentration, has a significant effect on a material's properties. The design of products with specific material characteristics has required the development of many processes to control convection (such as in the growth of semiconductor crystals, and electromagnetic stirring in steel casting). The expansion of fundamental knowledge about the process of solidification requires collecting data in the absence of density-based convection, while most of science's solidification data (and thus the equations that science has fitted to those data) have been obtained under the influence of gravity. Only relatively recently, through clever experimental design (e.g., drop towers, high altitude parabolic flights, and space laboratories), have investigators been able to study solidification in an environment with ""micro-gravity""."

Jan 1, 2001

By Alan J. Hurd

"New insights into the development of microstructure in sol-gel films have recently been revealed by several diagnostic techniques, including imaging ellipsometry, ""chemical imaging"" by fluorescent tracers, light scattering from capillary waves, and finite-element modeling. The evolution of porosity during the continuous transition from dilute sol to porous solid in restricted geometries such as films and fibers is becoming clearer through fundamental understanding of evaporation dynamics and capillarity.IntroductionWith sol-gel processing, the full flexibility of solution chemistry can be exploited to make ceramic films and fibers with well controlled compositional characteristics. No less important is the ability to tune porosity and connectivity for specific applications such as optical and electrical coatings and membranes. Since the chemical and physical factors that determine the microstructure are not entirely understood, new diagnostics applied to sol-gel processing are welcome.Sol-gel films and fibers are distinguished by processing that takes a sol through continuous stages of increasing concentration and connectivity of a solid precursor. The liquid carrier is usually volatile or, at least, volatilizable through heat treatment. During deposition through states of increasing solids concentration, this sol might gel, as in bulk sol-gel processing, however, the gel state may be a fleeting transient that quickly empties of liquid. Nevertheless, the structures formed in solution during this stage influence the structure of the final solid. In particular, porosity is likely to be a remnant of networks formed in the sol-to-gel transition. Here we report on experiments whose goal is to discover the factors involved with porosity development."

Jan 1, 1994

By Qixing Yang, Björn Haase, Fredrik Engström, Anita Wedholm

"MiMeR, the Minerals and Metals Recycling Research Centre at Luleå University of Technology, Sweden, started industry-related research work to stabilize an EAF slag from Höganäs AB with of CaO/SiO2 values near to 3.2. The intention was to determine the suitability of the EAF slag as construction material after stabilization. Some of the stabilizers effective for preventing disintegration of AOD slag were examined in laboratory tests for stabilization of the EAF slag. The EAF slag samples were mixed together with stabilizers for melting at 1600ºC and then cooling in a crucible system. With a laboratory granulation system, the liquid EAF slag was cooled rapidly using air. Samples from the tests were characterized by different techniques, including XRD and SEM. Some of the results from the work may be useful for preventing slag disintegration and, thus, enhancing utilization of the EAF slag as construction material, thereby saving valuable natural resources.IntroductionAt steel plants of some MiMeR member companies, steel grades with low carbon contents were produced in Electric Arc Furnaces (EAF). EAF slag was tapped out of the furnace to slag pots for transport to slag yards, where the slag was poured on the ground. Very often, the EAF slag disintegrated during cooling on the ground. Fines from the slag disintegration were often difficult to handle and use as material for road construction [1, 2]. The EAF slag disintegration was rather similar to the disintegration occurring in the slag tapped from some AOD (Argon Oxygen Decarburization) converter heats.Literature studies show that formation of dicalcium silicate (C2S) is the main reason for the disintegration or dusting of AOD slag from production of stainless steel [1-4]. The C2S can form while the content ratio of CaO to SiO2 of the slag, CaO/SiO2, exceeds 1.4 [1]. Values of CaO/SiO2 for the AOD slag are often near to 2.0, making the C2S a predominant slag component. The ß phase of C2S, ß-C2S, transforms into its low temperature ? form in the temperature range of 400-500°C, inducing a volume expansion of nearly 12% [1-4]. The volume expansion disintegrates the AOD slag."

Jan 1, 2008

By Susumu Okabe

Top blow injection has been applied to continuous copper smelting and converting by Mitsubishi Materials Corporation since 1974. In this process, injected feeds are captured by and dispersed in the molten bath immediately and effectively, and the reaction is enhanced by the agitation of the bath. The continuous motion of the molten bath, however, may cause severe damage of furnace lining materials, if the injection is not controlled and the furnace is not designed properly. In order to suppress refractory wear, especially at the bath line, surface wave of the molten bath should be moderated. A cold model study was carried out with water bath in a cylindrical vessel and the physical model was derived which correlates the oscillation of gas jet impingement on the bath surface and the surface wave. It was found that a half of the proper frequency of the gas jet impingement coincides the proper frequency of the surface wave.

Jan 1, 1998

By J. Alberto Vázquez M.

A sensor employing yttria-stabilized zirconia (YSZ) was used to determine the oxygen activity of molten copper at laboratory scale at temperatures of 1200° and 1300 dc. The reference electrode was a Ni-NiO mixture. The amount of the deoxidizing agent (CU3P) ranged from I to 3% of the mass of copper. Thermodynamic analysis of the Cu-O-P liquid system was carried out to predict the required deoxidizing agent and the final composition of the molten copper. Both results, calculated and experimental, show that the oxygen removal is more efficient at lower temperatures. The kinetics of the deoxidizing reaction is very fast in the first minutes of the treatment. A metalography analysis of rapid cooled samples show the oxygen and phosphorus distribution

Jan 1, 2003

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By Hiroki Kumakura, Kotaro Seki, Takashi Nagai, Masahito Abe, Daiki Noguchi

A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. PGM in the catalyst are supported by ceramics for four-wheel vehicle or metals such as stainless steel for two-wheel ones. The recycling process of PGM from the metal-supported catalyst has not been developed, while the process for ceramic-supported catalyst was developed, such as Rose process. We designed a noble recycling process of PGM from metal-supported catalyst using complex oxides between PbO and PGM oxide. In this study, complex oxides, PbPt2O4, PbPdO2, PbRh2O4 and so on were synthesized at about 773–973 K. And the dissolution behavior of these compounds to hydrochloric acid was investigated. PbPt2O4 and PbPdO2 were dissolved to hydrochloric acid easily, but PbRh2O4 was not.

Mar 1, 2017

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By Christian Trassy, Pierre Proulx

"Inductive plasmas are now commonly used in material processing: spraying, powder synthesis, densification or spheroidization. An inductive discharge presents, in the coil region, recirculation eddies due to the Lorentz forces, resulting in an axial backflow. If the central jet is strong enough to ""pierce"" the recirculation this axial backflow disappears on the centerline, but the external layer of the injection flow is skimmed by the remaining eddy, and particulates are rejected to the discharge periphery. To avoid this disadvantage, it is common to introduce the injection pipe inside the discharge, so that its outlet is positioned after the recirculation eddy. The powders remain confined in the axial zone, to the expense of shortened residence time.In order to increase the efficiency of the particle trajectories, a double flow injector has been designed. It enables the particles to travel closer to the axis, while the outer schrouding gas is skimmed and passes through the electromagnetic eddies. This injector is made up of two concentric tubes. The powders are injected with the carrier gas in the inner tube. A schrouding gas is injected in the annular space between the inner and the outer tubes. The powder is confined to the vicinity of the axis, resulting in a more homogeneous thermal treatment.Tungsten powders have been spheroidized with and without this device. Using the double flow injection, the spheroidization yield has been increased from 70 % up to 95 %.The design of such an injection device has. been studied and improved using numerical modelling. Another useful tool, a visualisation technique described elsewhere, has been used for the experimental study, that drastically simplifies the comparison between experimental and theoretical results: injecting yttrium oxide into the discharge results in a colorful display of the 4000 K isothenn: the ""cold"" zone, below 4000, appearing as red, and the ""hot"" zone as blue. Furthermore, it is of great industrial interest since it is a very cheap and efficient way to obtain a picture of an important isotherm."

Jan 1, 1999

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

By A. Navarra

Within conventional copper and nickel-copper sulfide smelters, ladles of molten matte are fed into converters. These converters blast oxygen-enriched air into the matte, thereby eliminating iron and sulfur. The converting reactions are exothermic and, indeed, the converter heat balance is often a limiting consideration on the smelter throughput. If a portion of the matte were fed in solidified (granulated) form, this would support higher oxygen enrichment, and lower volumes of converter offgas, allowing higher throughput. This approach is not applied in conventional smelters, partly because of the copious amounts of water that must be evaporated in typical granulators, as in the Kennecott-Outotec process. The current paper recalls a waterless matte granulator that had been pioneered in the 1990’s, and is applicable to conventional smelters. A mathematical formulation is presented that can be used in the context of simulation-based optimization, to estimate the size and impact of waterless matte granulation.

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By Christian Redl

"The Lattice Boltzmann Method (LBM) solves fluid dynamics problems based on a discrete mesoscopic approach. It is based on the Lattice Boltzmann equation which is a special discretisation of the continuous Boltzmann equation. Its principle advantage is that it can handle complex physical phenomena (like interaction between different components and surface effects), complicated boundary and initial conditions very well, free from many gridding and stability constraints that plague conventional numerical methods used for fluid flow simulations. Complex structures like porous media can be resolved directly. The LBM algorithm has a simple structure and acts locally, which is favourable for parallel computing. Its potential for metallurgical process simulation is demonstrated in the present study which is concerned with the simulation of the fluid flow in a copper winning electrolysis cell. The electrolyte is modelled as the carrier fluid and the oxygen is considered via a so called active scalar equation. The modelling of buoancy, momentum exchange and the free surface requires special effort. The results of the simulation are validated against experimental data obtained by Laser-Doppler-Anemometry. Despite the simplifications made, good agreement between the simulation and the experiments was found.IntroductionThe hydrodynamics in an electrometallurgical cell is a complex, highly non-linear phenomenon. It includes the simulation of a two component system with high density ratio, gravity driven flow and a free surface. A general solution to this problem is currently unknown.The flow field is a result of the combination of various hydrodynamic effects [18]. Metal deposition at the cathode yields in a decrease in the ion concentration, which reduces the density of the electrolyte. At the anode molecular oxygen is formed as a consequence of the oxidation of water molecules. The oxygen is solved in the electrolyte and again the electrolyte density is decreased. Both effects lead to a free upwards directed convective flow, refered to as natural convection."

Jan 1, 2001

By Mingsheng He, Yunhui Tang

The structure and granularity of biological origin aragonite from abalone shell during wet grinding in a ball mill were studied with X-ray diffractometer, with morphology studied by scanning electron microscope (SEM). It is shown from the results that the particle sizes of aragonite decreased with grinding time, so did the X-ray diffraction (XRD) peak intensities, while the full widths at half maximum increased. A calcite XRD peak with low intensity and great width was observed in nearly all the samples with various grinding time, whereas the intensity of the peak increased obviously after grinding time 300 min. It is shown from the SEM results that the size of aragonite dropped with grinding time until it reached 20 nm and then kept constant, while that of calcite dropped first and then rose at the minimum about 10 nm until to the constant size as in aragonite. It was observed that the mineral content obtained from XRD show an obviously change that the calcite increases while aragonite decreases, which indicated the occurring of a polymorphic transformation of aragonite into calcite.

Mar 1, 2017

By Fumito Tanaka

In the Mitsubishi Continuous Copper Smelting & Converting Process, the heat for the dissolution of scraps is effectively supplied from the melts strongly stirred by top injection. Various kinds of shape of scraps not only powder but also lump, sheet, cube and so on can be treated without any emission of dust and fugitive gas, and no additional furnaces for scrap processing is necessary. Therefore, this process is much suitable for recycling. The authors have investigated the melting rate of ice sphere into a water bath equipped with top blowing lances as a basic study for the dissolution of scrap. Hydrodynamic experiments were carried out, and mathematical models were applied to the results. The results show that the melting rate of ice sphere strongly depends on the standing waves at the bath surface.

Jan 1, 2001