Search Documents

By Anatoly Sudnev, Vladimir Skorohodov, Igor Kudryavtsev, Boris Radionov, Dmitriy Panov

"In cobalt production technology at a stage of solutions purification manganous cake (slime) basically containing hydroxides of the specified metals is formed. The possibility of full cobalt recycling in the basic technology of metal production at slime processing with generation of pure manganous compounds is shown. After slime dissolution in sulfuric acid in the presence of reducers the solutions containing cobalt, manganese, nickel and other nonferrous metals are formed. Optimum conditions of selective precipitation major part of cobalt by sodium hydroxide from the obtained solution are defined, thus more than 95% of manganese are remained in the solution. The cobalt precipitate is directed to the basic technology and the solution is purified by sorption. The most effective sorbents are chosen, optimum modes of its use are found. Examples of manganese recovery from the purified solutions as MnO2, MnCO3, Mn(OH)2 with a ratio manganese : impurities more than 3000 are presented.In the processes of hard alloys manufacture and processing of cobalt-bearing primary raw materials various cobalt-manganous slimes are formed. After leaching by solutions of mineral acids the problem of cobalt and manganese separation becomes an actual. The common way of metals separation in a solution is the Shreyber’ alkaline method allowing rather selectively to precipitate of cobalt hydroxide by sodium hydroxide. However this way does not allow separating completely target metals because of transfer of some manganese in the hydrated precipitate, even at its rather low content.In the given work the results of researches to improvement of a traditional way by inclusion to hydrometallurgical technology of operation of sorption separation of the specified metals are presented. The main goal is definition of conditions to achievement of the complete removing cobalt at hydrolysis with the minimum sedimentation of manganese and the subsequent additional recovery of cobalt by ionites from the obtained solutions."

Jan 1, 2008

By W. C. Chang

Phases and magnetic evolutions of melt spun Nd9.5(Fe1-xCox)85.5B5 (x=0, 0.05, 0.1 and 0.15), (Nd1-yLay)9.5Fe85.5B5 (y=0, 0.0.5, 0.1; and 0.15) and (Nd0.95La0.05)9.5(Fe1-zCrz)81.5B9 (z=0, 0.033, 0.067 and 0.1) nanocomposites: have been investigated. It was found that a. dilute Co substitution for Fe, x=0:05-0:15, in Nd9.5(Fe1-xCox) 85.5B5 improved not only Curie temperature but also the remanence and maximum energy product. Partial substitution of La for Nd in(Nd1-yLay)9.5Fe85.5B5 may suppress the grain growth of the materials during thermal treatment. Exchange coupling between the Nd2Fe14B and a-Fe was found: to increase with increasing La content. A dilute La-substitution, y=O. 10, has proven to decrease the optimum wheel speed required for preparing melt spun ribbons with better magnetic properties; Furthermore; a slight substitution of La for Nd in (Nd0.95La0.05)9.5(Fe1-xCrx)81.5B9 nanocomposite reduced the crystallization temperature of the over-quenched ribbons and led to the formation of a multiple phases mixture. Nevertheless, a dilute Cr addition increases the Tg of (Nd0.95La0.05)9.5(Fe1zCrz)81.5B9 and also suppresses the formation of the undesired (Nd,La)2Fe23B3 and Fe3B phases: Cr was found to play an important role in grain smoothening or magnetic separation which consequently increased the Hc of Cr-containing materials.

Jan 1, 1997

By Wellington Pereira Inácio, Frederico Muylaert Margem, Artur Camposo Pereira, Sergio Neves

"Natural fibers are currently gaining attention as reinforcement of polymer composites for uses in engineering parts for automobile and building construction. In spite of environmental, economical and societal advantages, the natural lignocellulosic fibers are not as uniform in their dimension and properties as compared to synthetic. In recent works it was found that the variation in strength could be correlate to the equivalent diameters for several lignocellulosic fibers including the sisal fibers. In the present work an investigation on a possible correlation of the equivalent diameter with changes in density and elastic modulus was carried out. Precise measurements of the equivalent diameter, conducted in a profile projector, were correlated with the density and the elastic modulus by means of the Weibull statistic analysis. The results showed that an inverse correlation with the diameter also applies for both the density and the elastic modulus with a high degree of precision. SEM observation of the sisal fiber in structure and fracture aspects strongly indicate that defects and microfibril participation could be responsible for the inverse correlation.IntroductionAccording to Kalia [1], cellulose-based fibers are currently being pushed owing to their ""green"" image. Contrary to synthetic glass fiber, extensively used in our modem technology, these lignocellulosic fibers are renewable and can be incinerated at the end of the material's lifetime without adding pollution in the atmosphere moreover, the amount of CO2 released during incineration process is negligible as compared to the corresponding amount taken up by the plant throughout its lifetime. Even if an industrial processing equivalent of C02 release is added, the lignocellulosic fiber is considered neutral with respect to the emission of gases responsible for the global warming [2]."

Jan 1, 2012

By Gennady I. Gulyayev

A mathematical model of plastic deformation occurring in cold plug drawing of mother tubes with initial cross-sectional wall thickness variations (CSWTV) has been developed. The main provision of the model is that eccentricity em is of such value that projection of all forces acting upon the plug in the deformation zone along the axis perpendicular to the drawing axis equals to zero. Calculations have proven that with other conditions being equal increase in the die cone angle and the deformation cycle number reduces CSWTV. Theoretical findings were confirmed by practical results. Keywords: cold, drawing, plug, die cone, plastic deformation.

Jan 1, 2003

By Patricio Ruz, Gabriel Riveros, Carolina Ramirez, Andrzej Warczok, Rober Treimer

"Continuous converting of copper matte produces slag with high cuprous oxide content. The corrosion of chrome-magnesite refractories with slag of high cuprous oxide content is a major problem. Properties of olivine type of slag make the slag very attractive for matte smelting and converting.Analysis of phenomena determining the slag infiltration into the porosity of a refractory and dissolution of refractory components in the slag allowed for better understanding of the mechanisms of refractory destruction.The results of laboratory scale tests of the olivine slag infiltration into open porosity and corrosion showed dominating effects of slag temperature and cuprous oxide content. The optical and X-ray examination of slag samples permitted the definition of the mechanism of formation of new phases and refractory deterioration. 71"

Jan 1, 2009

By Antrekowitsch Jürgen

The recycling of residues from metal producing by-products has become a main field of interest in metallurgical investigations. Forced by a stricter environmental legislation and the resulting increase of landfilling costs, combined with the aim to recover as many valuable metals as possible, a lot of different processes have been developed in the last two decades. Because of the high yearly tonnage residues from the iron and steel industry like slags, dusts and sludges have moved in the center of interest. Dusts from the steel mill, containing heavy metal oxides and halides did not play a considerable role as secondary raw materials for a long time. They even contain a huge amount of leachable elements and compounds which cause noticeable problems in case of a dumping. Nevertheless, the implementation of a new landfilling regulation, including a prohibition of aboveground dumping without inertisation, caused a rising interest concerning recycling technologies for such residues. In addition, the zinc content of these dusts became higher and higher and began to play the most important role for the economy of dust recycling.

Jan 1, 2006

By Albert W. Spitz

Profitably recovering copper and precious metals from copper bearing scrap is a demanding and frustrating combination of art, science and economics. With fluctuating markets, varying raw materials and increasingly stringent environmental regulations requiring process revisions, practically everything is changing. The volatile copper market constantly shifts the percentage of copper in the scrap that can be economically processed. Scrap that has value one day may incur a disposal cost the following day. Also with less copper in the scrap, more residuals, slag, fume, etc. are generated which frequently present disposal problems and infrequently generate income. The ever increasing amounts of electronic scrap add value to the copper produced by virtue of the precious metals present. Printed circuit board materials create more slag and organic off gases which must be treated. Finally, the emphasis on reducing emissions of organics and other metals, especially lead, is a continuing challenge. Stack gases, fugitive emissions and ambient air quality all demand constant surveillance.

Jan 1, 1997

By Minge Zhao, Yuandong Pei, Zhixing Zhao, Zejun Ma, Lili Ban

"Confocal scanning laser microscope (CSLM) has been applied to carry out the in-situ observation of melting and solidifying characteristics during iron ore sintering process, accompanied with TG-DSC test. It can be found that apparent Liquid phase forming temperature(LFT) and ending solidifying temperature(EST) is about 1190? and 1160?, respectively. Forming liquid phase during sintering process goes through four courses, these are shrinking, expanding, shrinking and expanding coexisting and expanding totally. For Yandi fine, the corresponding temperature of these four courses is about 1120-1160?, 1190-1196?, 1218-1220? and 1233-1270?, respectively. Although CAJ fine has more difficulty in forming initial liquid phase, but when liquid phase expands, it may have better fluidity and easier for liquid phase formation. Adding enough CaO, CAJ fine takes on high fluidity like Yandi fine, because liquid phase during sintering process is formed mainly by reaction between CaO and Fe2O3.IntroductionConfocal scanning laser microscope (CSLM for short) has been applied to carry out the in-situ observation of metallurgical phenomena, especially in steelmaking process. Recently, many researches on ironmaking process were conducted with CLSM. While for high temperature properties during sintering process, there are limited reports on in situ observation1-2). In this paper, melting and solidifying characteristics of iron ore were observed with CLSM under simulated sintering temperature, and high temperature properties of iron ore during sintering process was clarified based on the in situ observation results and TG-DSC research."

Jan 1, 2012

By J. S. Kirkaldy

A theoretical procedure is demonstrated for calculating two-dimensional binary cellular single-valued interfaces and extended to triple-valued (remelt) shapes. The numerical calculations for the single-valued local equilibrium problem which yield unique shapes as functions of the supersaturation parameter a and the partition coefficient k are reviewed. The cell amplitude L and wavelength A scale identically as the inverse velocity to the 112 power and the aspect ratio r is a constant equal to 312, independently of a and k for a < 0.5.. For 0.5 < a < m, L, A and r decrease asymptotically to zero indicating the finite amplitude nature of the instability at a = 1 and the existence of sub-marginal states which converge to a flat interface at a- m (Glv- m). Scaling comparisons between equilibrium single-valued and triple-valued and deep-rooted non- equilibrium cells are made.

Jan 1, 1992

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation&apos;s main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By Peter Bauer, Klaus Gamweger

"Gas purging systems are well established in nonferrous metallurgy at multiple steps during metal production, including melting, converting, alloying, and metal cleaning. Since the kinetics of all of these stages are positively influenced by using gas purging systems the overall process benefits are substantial. In the aluminum industry, inert or reaction gases are blown into the melt using porous plugs to achieve improved metal grades, higher productivity, and more efficient energy utilization. To enable the most effective application of the process gases a complete package, termed AL KIN, was developed by RHI that includes porous plugs, refractory expertise, gas supply technology, and gas control equipment. This paper discusses the technological and economic advantages of this system and the specific benefits of fuel reduction, production time savings, decreased process gas consumption, and improved refractory service life and maintenance are illustrated using an aluminum slug plant in Austria.IntroductionIn addition to high quality production, increasing productivity is the main goal in many aluminum cast houses to maintain or even strengthen their market position. The Neuman Aluminium Group, based in Austria, North America, and based in Austria, North America, and China, is the largest slugproducer for tubes, cans, and automotive parts worldwide. Recently, a comprehensive improvement program was initiated at the Neuman Aluminium Austria slug plant in Marktl - the main factory and technological centre of the group. The principal goal of the optimization project was to increase the productivity of the strip-casting production. The investment included a gas purging system, ingot preheating equipment, a new insulated launder system, and optimized melting cycles. However, the introduction of the gas purging system was pivotal to the project and has accounted for approximately 50% of the benefits achieved. This paper describes the AL KIN gas purging technology and details the process benefits resulting from the improvements at Neuman Aluminium Austria."

Jan 1, 2009

By R. Y. Wan

Low grade sulfidic-carbonaceous refractory ore from Newmont Gold Company&apos;s Carlin deposit was microbially pretreated. The biological pretreatment process gave partial oxidation of the sulfidic components of the refractory ore but the preg-robbing carbon continued to be active resulting in approximately zero cyanide gold extraction. A 495 ton pilot plant test heap was conducted using acidic thiourea leach following biooxidation. Activated carbon and cation exchange resin adsorption were tested for gold recovery from the thiourea pregnant solution. The results obtained from the test heap were not satisfactory. Gold extraction was low due to slow reaction kinetics which was caused by relatively large particles and very low winter temperatures. Problems existed in the thiourea-test heap and are discussed in this paper. An alternative heap leach process using thiosulfate has been successfUl at the pilot scale for gold extraction following biooxidation pretreatment of refractory sulfidic-carbonaceous ores.

Jan 1, 1995

By J. L. Liow

Studies have been carried out on the causes and effects of slopping in an annular cylindrical geometry such as the top submerged combustion reactor. Properties of standing waves formed such as the wave profile, period, pressure distribution and velocity have been derived analytically. The wear profile due to wave erosion was calculated based on the assumption of linear motion and that the wear is a dissolution process. The use of the j, factor showed that the wear was proportional to the square root of the wave velocity at any point. Using the dimensions of the lsasmelt reactor given by Errington et al. (1987)[11, the wear profile due to wave erosion was calculated using the analytical solution. The wear profile calculated was shown to have a maximum just below the initial bath surface. The wear was found to be concentrated in the region where the first asymmetric standing wave was most active. The results showed that the refractory near the bath surface will be affected by wave erosion, more so than any other parts of the reactor. The contribution of wave erosion on wear must be accounted for in assessing the total refractory wear of a vessel in which slopping exists.

Jan 1, 1991

By Chikabumi Yamauchi, Masami Tashiro, Toshiharu Fujisawa, Hiroyuki Snano

"Rare earth metals usually contain large amount of oxygen because of their reactiveness, and therefore oxygen removal is one of the major problems on the purification of rare earth metals. In the present research work, halide flux treatment at high temperature under inert gas atmosphere was applied to the oxygen removal from neodymium. NdF3 was used as a halide flux. Deoxidation reaction and its mechanism were discussed based on the experimental results. Halide flux treatment is very effective for oxygen removal from rare earth metals.IntroductionSolid Sate Electrotransport (SSE) process has been successfully applied for the elimination of interstitial gaseous impurities from chemically active metals[l]-[5]. However, to achieve a higher effectiveness of the SSE process, it is required a very low initial impurity content in the metal. In case of rare earth metals, it is known that they usually contain large amount of oxygen that should be lowered as much as possible before applying the SSE process. In addition, if effective oxygen removal is achieved by simple process, it is significant also from the industrial viewpoint. In the present work, the application of a halide flux treatment is investigated to remove oxygen from neodymium by using NdF3 as a flux. At first, deoxidation reaction and its mechanism were discussed based on the phase diagram of the Nd-NdF3-Ndp3 quasi-ternary system. Based on the results, oxygen content in deoxidized neodymium was calculated theoretically and it was verified by deoxidation experiments."

Jan 1, 1998

By W. R. Opie

Fundamentals of blast furnace smelting of low grade copper and precious metal scrap and residues are reviewed with emphasis on emission control, by-products produced, slag cleaning for high recovery of metal values and the evolution of an off-gas system to eliminate hydrocarbons that result from decomposition of plastics in the blast furnace- charge. Problems with tin, antimony and nickel in the smelter-refining cycle are discussed.

Jan 1, 1985

By X. K. Lan

The greater demand for high-quality large-diameter crystals has led to the robust idea of a free- flying solar-powered furnace satellite, whereby the buoyancy-driven convection effects are almost nonexistent, and diffusion-controlled crystal growth with minimal radial segregation is promoted. In the proposed solar furnace, a paraboloid of revolution imaging concentrator is used to focus the sun&apos;s radiation onto an-ampoule which holds the solid charge to be processed. The charge will start melting in the vicinity of the focal point, after which it is translated in order for the melt to resolidify as a single crystal. A ray-trace method has been developed to determine the incident concentrated solar heat flux on the ampoule surface for a perfectly-aligned configuration with an incoming columnated beam. A transient 2- dimensional conduction problem with phase change is formulated, which is solved using the commercial code FIDAP. Results highlighting the feasibility of growing GaAs, Ge and Si crystals with diameters of the order of 20 cm using the solar furnace satellite concept are presented. The transient temperature fields within various charge materials are quantified.

Jan 1, 1994

By Bernd Kopacek

"Nowadays more and more consumers substitute their conventional TV-sets and computer monitors by LCD panels. In the near future huge amounts of LCDs will start coming back to recycling. As LCDs with hazardous mercury backlight lamps are used an appropriate recycling technology has to be implemented.IntroductionLiquid Crystal Displays (LCDs) are widely used in notebooks, organizers, mobile phones, pocket calculators, measuring and control instruments, electronic games, hand-held miniature TVs, audio-video equipment, large signboards, automotive displays and more and more also for PC monitors and TVs.According to a study from Stanford Resources (San Jose, California) the annual value of LCDproducts reached 35 billion EUR in 2002, about 30% of this within the European Union, representing a total area of 2,1 million m2 Liquid Crystal Displays. An annual increase rate of about 15% is estimated for the next years (up to 4,1 million m2 in 2005).As LCDs are already on the market for several years, larger quantities of the more than 2,5 billion LCDs are coming into their End-of-Life stage for treatment. In 2005 this figure will become even more dramatic - 40.000 tons of LCD-modules contained in 2 million tons of waste electrical and electronic equipment (WEEE) or about 30% of total WEEE within EU. An amount which is representing 400 million EUR costs for incineration.Currently the only method used to deal with redundant LCD units is incineration or landfill. Both are expensive and causes emissions into the atmosphere (global warming) respectively water contamination (Class II) and difficulties in biodegradation. Up to now there is no recycling solution for LC-Displays available.As a consequence European Commission requests the disassembly of LCDs with an area bigger than 100 cm2 in the Directive 2002/96/EC of the European Parliament and of the Council on Waste Electrical and Electronic Equipment (WEEE Directive) of February 13, 2003."

Jan 1, 2008

By M. Tamura, K. Fujita, K Shinozuka, H. Daimon, H. Esaka

"In-situ observation of unidirectional solidification using transparent substance has been performed to investigate the growth direction of solid phase. Cell or dendrite of which preferred growth direction is not parallel to the heat flow direction was observed with various solidification conditions. Dimensionless growth direction (p) changes from 0 to 1 with increasing growth velocity at a constant temperature gradient. Introducing the dimensionless growth velocity, the relation between p and growth condition could be correlated.IntroductionTransition in macroscopic solidified structure from chill to columnar zone which is found in normal castings takes place via grain selection1). Cast products such as turbine blades are unidirectionally solidified, grain selection plays an important role to choose suitable crystals which have reasonable orientation in the region called ""starter"", which is a very initial part of casting2). Therefore, grain selection is a very important process in the formation of casting structure. The present authors have been studying on the process of grain selection using succinonitrile, which is a transparent organic substance and have found that the growth distance necessary for grain selection depends upon the solidification condition3-5). When the solid/liquid interface is dendritic, the grain selection occurs quickly. On the other hand, when the solid/liquid interface is cellular, it occurs slowly. We supposed that the growth direction of dendrite is different from that of cell when the substance is unidirectionally solidified. Indeed, Kurz and Fisher wrote in their text book that dendrite grows along its preferred growth direction, <100>, regardless of heat flow direction and that cell grows along heat flow direction regardless of its preferred growth direction1). However, there is no quantitative description about the growth direction when the solid/liquid interfacial morphology is cellular. Furthermore, there have been little works6) to study the growth direction of cell and dendrite."

Jan 1, 2000

By B. Q. Li

A numerical study of the developing fluid flow and thermal aspects during the staning phase of aluminum continuous casting processes is presented. The deforming finite element method, coupled with a quasi-Lagrangian formulation, is used to represent the growth of an ingot and the dynamic fluid flow and thermal behavior that evolves in the growing ingot. The mathematical formulation of the problem and the numerical treatment are discussed. The algorithm solves the free moving nodes as part of total unknowns with an automatic time step control for time integration. This permits an optimal computing efficiency while still keeping the computational errors under control. A selection of the results obtained using the algorithm is presented. The results are concerned with the evolution of fluid flow, temperature and solidification phenomena during a DC round ingot casting process, as it evolves from the beginning of casting operation to a steady state. These results show that the time-varying, complex fluid flow and thermal phenomena during continuous casting processes can be very well represented by the computational algorithm. The results also illustrate that, during the casting process, ~e fluid flow and temperature fields change drastically at the initial stage but evolve slowly afterwards

Jan 1, 1993

By Junji Shibata

Heavier rare earth, which is contained in a small amount in ores such as bastnesite and monazite, has been accumulated as a heavier rare earth residue without doing separation and purification due to the lack of suitable methods. The heavier rare earth residue includes seven rare earth elements such as Tb, Dy, Ho, Y, Er, Tm and Yb. Separation and recovery process of Dy, Y, Tm and Yb from leached solution of the heavier rare earth residue was investigated by using a column method with solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organophosphorous extractant whose trade name is PC-88A into a macro porous resin, Amberlite XAD-7. It was almost impossible to separate them in simple adosorption and elution steps. However, we attained to individually separate Dy, Y, Tm and Yb from the leached solution first by changing eluent concentration gradually from pH2 to 0.02kmol/m3 HC1 in the elution step, and secondly by using a development column and changing eluerit concentration in the elution step. The separation process flow was proposed for a heavier rare earth residue by using the solvent impregnated resin method.

Jan 1, 1998