Search Documents

By R. C. Hubli

A chemical model has been developed to investigate the dissolution of sulphide minerals in brine solutions containing copper and iron chlorides. The model has been employed to study the dissolution .of synthetic NiS using different initial concentrations of Cu(II), Cu(I), Fe(III) and temperature. The speciation of copper with particular reference to the formation of hydroxy-chlorides as a function of total chloride and H+ has been computed. The model predictions are in agreement with experimental results. It has been found that addition of Fe(III) results in the maintenance of a high Cu(II)/Cu(I) ratio leading to enhanced rates of dissolution and suppresses the loss of Cu(II) due to the formation of hydroxyl-complexes.

Jan 1, 1997

By Dany Racine, Daniel Marceau, Denis Laroche, Dmitry Lukovnikov

Carbon base materials play a critical role in the performance of Hall-Héroult cell. The determination of their thermo-physical properties is of primary importance for modeling and designing complete cell systems. However, overcoming the associated experimental hurdles is complex and often underestimated. Of them are the Poisson’s ratio measurements and the continuous oxidation/burning of the materials at temperatures above 200°C. The novel procedure developed in this research is based on the Gleeble® 3800 system. Its vacuum chamber allows test with a chosen atmosphere at temperature of more than 1000°C. Young’s modulus, Poisson’s ratio and the coefficient of thermal expansion values can all be adequately measured using a single test. Cylindrical carbon samples (: 50mm, L: 100mm) were tested in the modified system at temperatures ranging from room to 950°C without any trace of oxidation. The resulting values were also in good agreement with literature data for a specific graphite material.

Jan 1, 2015

By Sevket Acar, Tim Acton

"Zarafshan/Newmont is a 50/25/25 joint venture between Newmont Gold and the State Committee for Geology and Mineral Resources, and Navoi Mining and Metallurgical Combinat, two entities of the Republic of Uzbekistan. The Zarafshan/Newmont joint venture consists of a heap leaching operation which will process 220 million metric tonnes of existing low-grade oxide ore stockpiles (averaging 0.036 oz Au/t) from the Muruntau mine. Net recovery over the 17-year life of the project is expected to be 4.8 million ounces of gold.The plant construction started in October 1993 and operations commenced on May 25, 1995. The crushing plant consists of four stages of crushing and screening to produce a 95% passing 3.35 mm product, followed by heap leaching and gold recovery by the Merrill-Crowe process. The dore metal is refined at the Muruntau refinery. All gold produced by the joint venture is sold on the world market. IntroductionThe Muruntau mine and nearby town of Zarafshan are located in the center of the Kyzylkum desert, 250 miles west of Tashkent, capital of Uzbekistan. Following a mining conference in Moscow in 1990, a Newmont geologist was among the first team of westerners to visit the Muruntau Mine, the second largest gold producer in the former Soviet Union. At Muruntau, they found 220 million tonnes of low grade gold ore that had been stockpiled during the previous 25 years. In February, 1992, six months after Uzbekistan's independence, Newmont signed a 50/50 joint venture agreement with the Uzbek government to use heap leach technology to process the ore. The feasibility study was completed in November of 1992. Plant construction started in October, 1993 and operations commenced on May 25, 1995.Newmont Metallurgical Services performed metallurgical studies to obtain heap leach process design criteria parameters. The initial metallurgical study on 20 grab samples is the subject of this paper."

Jan 1, 1997

By Kuniaki Murase, Tetsuji Hirato, Koji Nitta, Yasuhiro Awakura

"The redox behavior of copper species in an ""ammonium imide"" room temperature molten salt was examined in order to clarify the applicability of the salt to the electroplating media of various metals. Trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)- amide (TMHA-Tf2N), having an electrochemical window of 5.6 V (50 °C), and corresponding copper(II) salt were synthesized. In TMHA-Tf2N media monovalent copper ion, Cu(I), was stable and Cu metal was oxidized, or corroded, in the presence of Cu(II) species. Cathodic electrodeposition of copper metal and anodic dissolution of it were, thus, one-electron reaction and their current efficiencies were almost 100%.IntroductionElectrodeposition of metals from aqueous solutions is an important soft process for manufacturing thin-film materials, surface finishing, and extractive metallurgy. However, the electrodeposition of base metals, such as zinc, chromium, and nickel, from aqueous media inevitably accompanies hydrogen evolution, which lowers the cathodic current efficiency of metal deposition. Since the electrodeposition of aluminium, titanium, and rare earths from aqueous media is actually impossible due to their largely negative redox potentials, nonaqueous media such as aprotic organic solvent and high-temperature molten salts have been employed for the electrodeposition of these metals. Room temperature molten salts (RTMS),1, 2) or room temperature ionic liquids, have also been developed as a promising electrolytes for the electrodeposition of base metals. In this field, chloroaluminates of alkylpyridinium or alkylimidazolium cation have been well investigated for aluminium3) or alluminium-alloy4-5) electroplating media. On the other hand, in order to avoid high hygroscopicity arising from the use of aluminium chloride, attempts have been made to combine the alkylimidazolium cations with fluorine-containing hydrophobic anions, e.g. BF4-,6) CF3SO3- (TfO-),7) (CF3SO2)2N- (Tf2N-),8) and H(HF)n-ions,9) and investigated for electrodeposition media.'°) Recently, a new series of RTMS consisting of tetraalkylammonium cations and Tf2N- anion, sometimes abbreviated as TFSI- anion, was found independently by MacFarlane et al.11, 12) and Matsumoto et al. 13) This type of RTMS, which is commonly named ""ammoniumimide"" salt, has a wide electrochemical window of ca. 5 V and, thus, the RTMS seems to be suited for practical application as a solvent for the electrodeposition process. In this paper, we report the electrochemical behavior of copper species in an ammoniumimide RTMS, trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)amide (TMHA-Tf2N)."

Jan 1, 2000

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By P. E. Nolan

The disproportionation of carbon monoxide is an important aspect of reduction processes, in the production of carbon filaments for composites, and in the removal of CO from CO,. It can also be a hindrance, causing carbon fouling of equipment and metal dusting. The reaction is thermodynamically favored at lower temperatures, but it occurs slowly. Catalysis of the reaction by transition metals has been examined. A materials science approach to the selection of a catalyst material and of optimum operating conditions is being taken in the present work. Of particular interest is characterization of a catalyst that can be repeatedly regenerated to prevent deactivation in long term use. Experimental data on a less studied catalyst, ruthenium, are reported.

Jan 1, 1992

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By Adolfo Pillihuaman Zambrano

Fe-Cr-C production is a very high electrical energy consuming process. Decrease up to 10% of this electrical energy is expected when self-reducing agglomerates are used. This research aims to understand how the synergetic effects are when stronger reductant, like Fe-Si, is substituted for coke in self reducing pellets. Brazilian chromites containing 41.2%Cr2O3 were mixed with petroleum coke and agglomerated with cement as the binder. Small amounts of 1%, 2% and 4% of Fe-75%Si were substituted for the equivalent petroleum coke, and pure silica plus hydrated lime were added for adjusting the slag composition. The mixture was pelletized, dried and submitted at 1773K up to complete the reactions. The results showed that the reduction reactions were 1.4 and 2 times faster with 1% and 2%Fe-Si addition, respectively, than with no addition. The microscopic analysis showed that it was formed a liquid phase, but the pellet did not collapse what indicates that the coalescence of the metallic phase depends on the dissolution of the pre-reduced particles of the chromites into slag.

Jan 1, 2008

By S. V. Cherty

The utilization of natural gas in non-ferrous industries during smelting and refining stages of copper , aluminum, zinc and lead was studied. The total amount of nonelectrical energy consumed in the production of zinc, copper, lead and aluminium, are 96.5% ,93%,92%, and 6 % respectively. It is calculated that 9.45 wt %of air of stoichiometric amount can be substituted by natural gas to the total air input in the nonelectrical energy utilization processes. The results showed that the non electrical energy may be substituted to an amount of 71 % ,52 % ,35 % ,32 % ,and 26% ,in the production of lead, aluminium (plates, foils) copper, aluminium, zinc, respectivelly. Similar calculations are carried out in terms of energy in Btu for the total production of non-ferrous metals in the U.S. It shows that 51.866~106 millions of Btu of nonelectrical energy can be substituted by 54.58~106 cu. ft of natural gas. Finally, the substitution of non electrical energy in terms of equivalent coal energy is discussed. 1t is shown that total non electrical energy is equal to 1.852 million tones of coal .If this 1.852 million tones of coal is replaced by natural gas, a total savings of 22.14 million dollars are achieved. The total or partial substitution of coal by the natural gas in the existing industrial processes and modification of redesigning the processes is discussed.

Jan 1, 1993

By Xian-Dong Zhou, Guo-Sheng Sun, Jianzhong Luo, Hong-An Guan

"Oxygen utilization rate of the pretreatment process which adopts biological contact oxidation method for slightly polluted supply water is relatively low, less than 10%, usually lower than 3%. So the aeration amount is not determined by calculated value of oxygen demand when doing process design, but by the ratio of gas and water. The aeration way of the biological pretreatment process for slightly polluted supply water was introduced in this paper. In the foundation of the principles of mass transfer kinetic theory and experimental data, the change law of DO (dissolved oxygen) and ammonia in the aeration tank was analyzed to explore aeration method which will help to improve the overall effectiveness of handling capacity.IntroductionThere are many kinds of filler used in the biological contact oxidation process, such as flexible solid filler, composite filamentous filler, powdery clay filler, particle ceramic filler and so on. Regardless of the different forms of filler, there are a couple of common points in the function of the aeration[1,2]: (1) The aeration process in biochemical tank not only provides adequate oxygen for the biological reaction, but also plays as a role of stirring water; (2) Biochemical reactions mainly happen in the upper reaches of tank, but seldom at down-streams.This paper, from the perspective of changing aeration way, discussed the feasibility of improving the effectiveness of biochemical reactions without increasing aeration amount, which would have some leading significances for the operation and management of similar projects."

Jan 1, 2008

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By Ruirui Wei, Yanhui Liu, Fangqing Yin, Meilong Hu

In China, Basic Oxygen Furnace (BOF) slag is traditionally used as an aggregate for civil engineering, for road engineering and fertilizer. In order to make full use of BOF slag, the experiments of BOF slag with high temperature roasting has been carried out and the phase transformation is studied. The BOF slag from Chongqing Iron & Steel is roasted in the electric muffle furnace at three different temperature. The influences of the high temperature roasting on change the phase composition of BOF slag was characterized by XRD. The results revealed that SFCA was produced at the high temperature in air atmosphere and melting temperature of slag was lowered. Therefore, if the BOF slag which treated by roasting was utilized in the sintering process, it is advantageous to improve the sintering strength and the formation of the liquid phase and reduce fuel consumption in the sintering production process.

Jan 1, 2015

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Shaohua Ju, Jin-hui Peng, Ya-jian Wang, Shuai-dan Lu, Li-bo Zhang, Lei Guo

"The granulation of a red mud is of great importance for recycling this material as an adsorbent for waste water or gas. A new granulating process was developed and its effect was evaluated. To reduce the cost of the granulation process, the wet filter cake (containing 25% water) was directly mixed with different cement contents (4%, 6%, 8% and 10% based on wet material). The mixtures were placed in a moist environment for 4 days, and then were washed with deionized water until the pH values of leachants were lower than 9.0. The efflorescence ratio, surface area and particle size of the aged mixture were determined, respectively, by bottle shaking experiments, N2 adsorption and screening. The results showed that the best addition of cement is 2%, and this yielded granulated material with a particle size of less than 2 mm, an efflorescence ratio of 4.83% and a specific surface area of 17.42 m2/g.IntroductionRed mud is a residue of the aluminium industry that is produced during the alkaline extraction of alumina from bauxite by the Bayer process. For every ton of alumina that is produced, the amount of red mud generated can vary from 0.3 to 2.5 tons, depending on the characteristics of the bauxite. In its typical form, red mud is brick red in colour, caustic, about three times as dense as water and, when un-neutralised, has a high pH, typically around pH 13 [1]. It is primarily composed of iron oxide, silica and alumina, along with traces of heavy metals. Red mud particles are quite small; typically 99% will pass through a 0.6 mm sieve and 87% through a 0.038 mm sieve [2],"

Jan 1, 2012

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

By H. Kung, T. R. Jervis, M. Nastasi, T. E. Mitchell

"A systematic study of the structure-mechanical properties relationship is reported for nanolayered composites of MoSh-SiC, Mo-MoSh, Mo-MoShNx, MoSi2-MoSi2Nx, and Mo-MoShMoSi2Nx (x=3-4) synthesised by sputtering techniques. These composites have been studied by nano-indentation and cross-sectional TEM as a function of annealing temperature. As-deposited layers are amorphous except for Mo. With increasing annealing temperature, first MoSh and then SiC crystallize, while the hardness progressively increases until the layers start to spheroidize and grain growth sets in at 900ºC. For the case of Mo-MoSi2, the layers react and the composite deteriorates rapidly. However, MoSi2Nx remains amorphous up to 1000ºC, suggesting that it could act as a diffusion barrier between Mo and MoSi2. In fact the Mo. MoSi2Nx, MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx nanolayers are found to remain stable up to such temperatures. IntroductionMolybdenum dislicide, MoSh, is a potential matrix material for high temperature structural composites due to its high melting point and good oxidation resistance at elevated temperature [1]. The two major drawbacks for structural applications are inadequate high temperature strength and poor low temperature ductility. Silicon Carbide (SiC) being hard and thermally compatible with most ceramics and intermetallic compounds, has been found to be suitable for second phase reinforcement in various structural applications and, in particular, the addition of SiC whiskers improves the high temperature yield strength of MoSi2 [2]. While most of the research in MoSb-SiC composites has been on the particulate form of SiC, laminated composites may offer unique properties. It has been shown that synthetic multilayers with alternating layers of metal and/or compounds may exhibit interesting mechanical properties [3]. Enhancement in mechanical properties by decreasing the wavelength of multilayer spacing has been studied extensively. In general, two types of strengthening have been proposed: (1) Hall-Petch strengthening [4,5], where the strength increase is inversely proportional to the square root of the layer thickness; (2) Koehler modulus strengthening [6], which increases with modulus difference and decreasing layer thickness. In the present study, we have performed a systematic study of the relationship between strength and structure in a number of different nanolayered systems based on MoSh. Layer thicknesses have been varied and their nanostructures have been varied by heat treatment. Previous work on MoSi2-SiC is summarized [7]. In an attempt to improve fracture toughness, MoSh-Mo nanolayered materials have been prepared but are found to react and deteriorate. Previous work has shown that nitrided MoSi2 (MoSi2Nx with x=3-4) is highly stable [8] and so nanolayered composites of MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx have been prepared to assess the' stability and mechanical properties of these composites. Preliminary results are presented."

Jan 1, 1994

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Angus Hellawell

The application of the common tangent principle to free energy - composition surfaces is considered. It is shown that the construction requires that single phase surfaces on either side of a two phase volume must always exhibit the same sign of curvature - contrary to that shown in many published phase diagrams. In general, these curvatures will be such that the surfaces are mutually concave towards the more stable phase. A number of examples are discussed.

Jan 1, 1991