Search Documents

By Raymond M. Stateham

The Bureau of Mines has developed a portable, lightweight device for determining the integrity of resin-grouted roof bolts. The instrument functions by sending a known pulse of ulstrasonic energy into the bolt and comparing the amount of energy reflected hack with the original measured pulse. Where the bolt is properly bonded or coupled with the rock, the energy passes through the bolt-resin-rock interface and dissipates in the rock. Where the bolt is not properly coupled, the energy is reflected back along the bolt to the instrument. The ratio of reflected energy to the pulse approximates the fraction of the bolt's surface that is improperly bonded. The instrument is easy to use. The operator holds the sensor head of the device firmly over the head of the bolt to be tested, causing the pulse of ultrasonic energy to be imparted to the bolt. The device then listens for reflected energy. This cycle is repeated about 200 times per second until an evaluation of the bolt installation is made and indicated by colored lights in the display window. Bolts having 50% or less of their surface bonded are considered had and cause a red light to he illuminated. Bolts with 50% to 75% of their surface bonded cause a yellow light to be lit and are considered marginal. Bolts having more than 75% of their surface bonded are considered good and cause a green light to be lit. The indicator lamp remains on for about 4 seconds and then goes off, indicating that the instrument is ready for another test.

Jan 1, 1982

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Bruce K. Hebblewhite

Tower Colliery is a longwall mine operated by BHP Coal Illawarra Collieries, Southwest of Sydney, Australia It mines the Bulli Seam at a depth of approximately 450m. The surface topography overlying the mine consists of several steep-sided river gorges, up to 68m in depth, which run at oblique angles across a sloping terrain Apart from some light rural development, the surface land is essentially natural bushland, but is traversed by a major freeway. This crosses one of the gorges on twin, six-span, box-girder bridges, with bridge piers up to 55m in height. Consequently, a major surface subsidence monitoring program has been in place for several years now, including intensive conventional, GPS and E DM surveying, plus real-time monitoring of critical components of the bridge structure. Although the bridge and freeway are outside the conventional angle of draw' subsidence influence criteria, and have seen only negligible vertical deformation as a result of mining, there has been widespread evidence of regional horizontal deformation of the land surface, large distances away from the mining area The effect at the bridge has been well within acceptable tolerances, primarily because of the regional nature of the movements, with very little differential movement observed at the bridge piers Gorge closure and evidence of large headlands of land moving `en masse' have been observed. Horizontal movements of hundreds of millimetres have been recorded in some locations where gorge closure has been monitored. Possible explanations of these movements include one or a combination of mechanisms such as pre-mining stress relaxation. valley notch effects, valley bulging, regional joint patterns, movement toward active goaf areas, vertical gorge shearing' and shear failure of horizontal bedding planes below the surface This paper presents a case study of the regional horizontal ?subsidence displacements? measured during mining. and a discussion of the possible explanations for these phenomena

Jan 1, 2000

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By R. Fritschen

In order to investigate locations, source parameters, and source mechanisms of mining induced seismic events, a local network of seismic stations was installed at a coal mine in the eastern part of the Ruhr District (Germany). The recorded events were located with the help of an anisotropic velocity model, which accounts for the fine layering of the carboniferous strata. Most of the events took place about 50 m above the working Luise 76-10. Their locations correlated with the advancing working face, and the number of events increased when pillar edges were undercut. The source mechanism, i.e., the orientation of the fracture plane and the direction of displacement on this plane, could be determined for several seismic events. The majority of them was characterized by a fracture plane parallel to the working face and an almost vertical dislocation on this plane towards the goaf a mechanism resembling the breaking down of the hanging wall. The fracture plane had a dimension of about 100 m. Probably the fracturing of a sandstone layer, located approximately 40 m above seam Luise, was responsible for the observed seismicity

Jan 1, 1999

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By Shiva P. B. Kolli

Surface mining of multiple scams by mountaintop mining methodology is complex in the Appalachian region of West Virginia. Excess spoil from the removal of overburden and interburden is disposed in the adjacent valleys. The valley fills so formed are some of the largest earth constructions, with a relief of 450 ft (137 m) to 650 ft (198 m) and a stretch of 500 ft (152 m) to 2000 ft (610 m). The stability of the valley fills has become an issue of public concern. This paper describes three cases of valley fill slopes. The analysis of each case involved the description of the geo-mechanical properties of different surface and sub-surface layers, and the surface configuration of the slope. Slope stability was carried out using deterministic as well as probabilistic approaches. Based on the analysis, it was found that valley till slopes were stable due to configuration, and the premise that valley fills with great stretch and high volume of spoil tend to be unstable does not hold.

Jan 1, 2001

By D. J. Maconochie

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modern houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various house designs.

Jan 1, 1992

By Danny J. Van Roosendaal

An investigation was undertaken to determine hydrogeological effects of subsidence over a longwall coal mine in the Illinois Basin. At this mine, approximately 200 ft of bedrock overburden is overlain by up to 150 ft of glacial till and localized water-bearing glacial sediments within a buried bedrock valley that overlies the longwall panel. A finite-element mechanical model of the subsided longwall panel shows sufficient strain to enhance permeability throughout the bedrock portion of the overburden. However, examination of the actual surface subsidence profile indicates that the overburden deformation is localized in narrow zones at the panel edges. The aquifer units at the base of the glacial sediments are confined by glacial clays (above) and weathered shales (below). Elevated water levels were observed in the glacial aquifers during subsidence, which indicates that the clays and shales maintained confinement as the overburden subsided and deformed. A three-dimensional ground-water flow model was used to simulate the effects of subsidence on the hydrogeologic system and to estimate inflows into the mine. Longwall retreat was simulated by several model runs, each representing a new longwall face position. Simulated heads and mine inflows were calibrated with recorded water levels and observed inflow conditions by modifying the hydraulic conductivity of particular model layers. Model calibration indicates that the permeability of certain lithologies, such as plastic underclays and weathered shales, is not significantly enhanced by subsidence. A worst-case scenario was simulated by inserting a deeply incised, sandfilled valley into the model, which had only minimal impact on the simulated mine inflows.

Jan 1, 1995

By David K. Ingram

The objective of this U.S. Bureau of Mines (USBM) investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored at two sites in southeastern Ohio. Site A included two adjacent longwall panels. Site B consisted of one longwall panel. Both sites had similar mine geometries and overburden thicknesses. The major difference between the two sites was the rock strata within the overburden. Multipoint borehole extensometers (MPBX) were employed to measure subsurface displacements. Survey monuments were installed above the centerline and profile of each panel to measure surface deformations. Subsidence of the surface was observed before and after movement was detected in the MPBX units. Initial and final displacement of the MPBX units occurred at the same time at both sites. No deformation was detected outside the panel area. The development of overburden deformation was different over each panel. The final subsurface failure characteristics also varied between panels.

Jan 1, 1994

By Madan M. Singh

Currently longwall coal mining operations require at least 3 entries on both the headgate and tailgate ends because of ventilation and safety requirements. Driving of entries, however, is a slow and costly process. Often it is a bottleneck in longwall development. Single entry gateroads are permitted in Europe and commonly used there. This study entailed ascertaining the feasibility of using a single entry in the United States, without sacrificing safety. This design was conducted for an operating longwall mine in the Black Warrior coalfield in Alabama, An understanding of rock loads and consequent support requirements is prerequisite to the design and successful demonstration of the single entry system. Efforts in this regard were directed at determining center (packwall) support requirements for various single entry widths. Critical to the analysis is knowledge of the nature and extent of side abutment stresses. In collecting geological and geotechnical information relating to the stability of the single entry, Engineers International, Inc. engaged in the following: ? Examination and inspection of the single entry demonstration at the Sunnyside Mine in Utah. Severe ground conditions and unacceptable levels of entry closure were experienced there prior to the tailgate phase. Observations at the mine presented a clear perspective on possible ground control problems for future single entry designs. ? Reconnaissance inspection and classification of roof rock conditions. ? Detailed mapping of roof structure in the areas to be instrumented. ? Installation of convergence stations in the longwall headgate to monitor roof movement during mining. ? Measurement of side abutment stresses in a yield pillar in the area of the convergence measurements. ? Measurements of coal fracture distribution by the detail area method. ? Rock properties determinations of roof, coal, and floor rocks; samples obtained by core drilling. ? Determination of floor bearing capacity by in-situ testing.

Jan 1, 1982

By Christopher Mark

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as "The UCS" for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: ? Brereton Limestone above the Herrin 6 seam (Illinois) ? Turner Mine Shale above the No. 9 Seam (Kentucky) ? Sandstone above the Eagle Coal (West Virginia) ? Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechnical exploration programs.

Jan 1, 2004

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Clarence O. Babcock

Since Vicat in 1833, the width to height ratio of a mine pillar has been taken as the fundamental variable in pillar design. From work in the laboratory by many investigators testing rock, Coal and concrete samples, it has been concluded by some that pillars with a width to height ratio of 10 to 1 are indestructible. It has also been concluded that a constrained core exists within the pillar which increases the pillar strength. The role of the roof and floor, if mentioned at all, is often noted in an incidental way. In the present work on laboratory testing of model pillars on concrete, coal, and rock instrumented with special strain gages, it was concluded that the end constraint and not the width to height ratio is the significant variable in determining the pillar strength. In tests where the end constraint is steel, a large compressive stress is produced on the horizontal plane of the pillar, and this effect increases as the width to height ratio is increased, resulting in an increase in pillar strength. If the end constraint is not steel but something with a small Young's modulus, the state of stress in the horizontal plane may be tensile, increasing as the width to height ratio increases, resulting in a decrease in pillar strength. Related to mining, the results are that a large width to height ratio pillar is strong for strong roof and floor and weak for weak roof and floor. That is, the roof and floor and not the width to height ratio determine the pillar strength. The confined core condition should be verified by testing if large pillars are to be used. If there is no confined core or the pillar is in tension, smaller pillar sizes should be used. The final conclusion is that the geometry alone is meaningless in pillar design.

Jan 1, 1984

By Jeffrey Johnson

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company's Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and¬MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

Jan 1, 2003

By D. E. Winston

Roof falls are the major cause of fatalities in the, coal mining industry and the prevention of roof failure is a major concern of mine management. Many ground failures observed underground are associated with geological discontinuities such as fractures, faults, clay veins and sandstone channels inherent in the earth's crust (Rinkenberger, 1977). To properly design a mine requires an advance knowledge of such geologic discontinuities and this is not always available from exploration boreholes. The use of remote sensing for mine planning is a relatively new development, and is at present being used primarily by the Roof Control Support Branches of the Mane Safety and Health Administration (MSHA) in Denver and Pittsburgh. However, technical advances, coupled with public access to previously unavailable photographic products, make remote sensing a useful aid in the difficult process of mine planning (Jansky and McCabe, 1979). Remote sensing techniques are being used to predict the location of geological features in advance of mining which influence roof conditions. The features appear on photographic images as linears, which are plotted on a mine map and serve as a planning tool for mine management. Also, during development of entries toward a linear, mining personnel will be on alert for signs of unstable roof conditions which might normally go undetected. Preventive action can then be taken before a fall occurs. A confusing aspect in remote sensing, analyses is terminology such as linear, lineament, fracture trace and joint. In this report the term "linear" refers to a line-like appearance on an aerial photograph or satellite imagery which signifies a naturally occurring geologic feature no the earth's surface. The objective of this paper is to describe the use of remote sensing techniques as an aid in predicting geological discontinuities which might produce hazardous roof conditions to a mine operating in the Pocahontas No. 4 Seam in southern West Virginia. Mine projections and roof control plans will he developed based on this and other available information such as data from cored drill holes.

Jan 1, 1982

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction¬al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt ten¬sion of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984