Search Documents

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Yingda Zhai

The range of interburden thickness between coal seams in Datong Mining District of China is large. From mining operation point of view, the closer is between the two seams, the greater is the impact from the upper seam when the lower seam is mined. This impact is most notable when the two seams are ultra-close. In this paper the definition of ultra-close seams and its practical method of determination are presented. Based on the difference in strata thickness in the interburden and the concept of "yield depth ratio" which is defined as the yield zone depth in the interburden to the total thickness of interburden, the roofs of the ultra-close multiple seams in the Datong District of China were divided into 3 types: (1) false roof or rock partings in coal seam. This type of roof does not require special handling except mining them simultaneously as one single seam. The roof thickness is slightly less than 0.5 m; (2) completely broken roof. In this type of roof, the yield depth ratio is larger than (or equal to) 1. When the roof thickness is larger than 0.5 m but less than 2.0 m, the yield depth ratio must be smaller than 1; and (3) fractured roof. In this type of roof, the yield depth ratio is less than 1 while the roof thickness is larger than 2.0 m. In retreat longwall mining, if the gateroads of the lower seam are located under the gob of upper seam, roof bolting can be used in the 3rd type of roof. But if the 2nd type roof exists, powered supports must be used.

Jan 1, 2005

By Ximeng Li

The entries that are subjected to dynamic pressure are much more difficult to maintain due to repeated disturbance. A case study of an entry stress distribution was performed using the FLAC3D program. By analyzing the distribution of stress field around the entries, this paper provides guidelines for entry support design in the lower (#16) seam subjected to the repeated disturbance from longwall mining in the immediate overlying (#17) seam, 72ft (22 m) above. The results showed that there was stress superposition inside the barrier pillar in the lower seam, 15ft (5m) to 45ft (15m) deep, during development. The influence zone of the front abutment pressure in the upper (#16) seam was about 100ft (30m) outby the faceline. The stress-relieved zone was from 0 to 100ft (30m) inby the face. The area further inby the face (i.e., 230 ft (70 m) inby the face) was within the gob compaction zone. Along the face advancing direction, the affected zones of the entries in the lower (#17) seam that were subjected to the dynamic pressure from longwall mining of the immediate overlying seam could be divided into four stages: pillar development stress stage, front abutment pressure stage, unstable gob stage, and stable gob stage. Those entries within an area from 100ft (30m) outby to 100ft (30m) to 230ft (70m) inby the faceline should be reinforced with special supports. The numerical modelling matched the monitoring results well.

Jan 1, 2013

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development'. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines' Mine Roof Simulator.

Jan 1, 1995

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By Saeed Zandi, Kazem Oraee

"Tunnels and galleries are the most important structures in coal mines. They are used for variety of purposes, such as transporting ore and people and for ventilation. A well-designed support system is necessary to stabilize structures and prevent collapse.Using rock bolts increases the strength of the rock in which tunnels are made. Rock bolts are used extensively in most underground mines today, and coal mines are no exception. Almost all galleries in a typical coal mine use some type of rock bolt, at least, as a means of partial or supplementary support.In this research, changing the support system from expensive methods to the use of rock bolts as the primary means of support is discussed, with the focus on a particular gallery in Hejdak coal mine. Visionary design methods, in conjunction with rock mass classification schedules, were used to determine an optimal rock bolt pattern. For this purpose, rock mass rating (RlVIR) and quality index (Q) classification systems were used. Several empirical methods were also used to design an optimal pattern for rock bolt installation in the particular tunnel under analysis.As such, the tunnel support system was designed using both finite element and empirical methods. Finally, the results obtained from both numerical and empirical methods were compared under different load conditions. The methodology prescribed in this paper, together with the comparison, can be a useful tool when selecting a support system. The results can also be used to design a support system in this and any other coal mine with similar conditions.INTRODUCTIONSince the advent of underground excavation techniques, one of the biggest challenges has been stabilizing tunnel walls and preventing roof collapse in tunnels and other underground openings, such as galleries. Loose rocks and layers drop into tunnels and galleries, except in very hard rock. Underground roof collapse and falling rocks can have devastating effects on the safety of operation personnel and equipment and can seriously affect production. When designing an underground coal mine, the stability of tunnels and galleries is an important parameter that should be studied carefully because it has an important role in the production process of the mine. Therefore, an appropriate and well-designed support system is necessary for preventing collapse and helping to stabilize the tunnels and galleries."

Jan 1, 2016

By Kewal K. Kohli, Stefanie Self

"Three cases of surface subsidence investigated over abandoned coal mines after flooding in one case and dcwatering in two cases are presented in this paper. Mining was conducted by the room and- pillar method at all the mines leaving stable pillars. This paper will discuss the background chain of events and the likely causes of the pillar failure resulting in surface subsidence.CASE NO.1BackgroundThe Pittsburgh scam was mined in 1960 by the room-and- pillar method, leaving pillars (Figure I) through Mine A. located in Monongalia County. West Virginia.The mining height in U1is area was 1.83 m (6 ft) with an average mining depth of 140 m (460 ft). The mining recovery was 62% and the safety factor of the pillars was calculated at 1.15 using the Bieniawski ( 1984) fom1ula. For stable pillar design. a 1.5 safety factor is recommended. A 1.15 safety factor is considered marginal. Pumping continued after the mine was shut down in 1960 to prevent water seeping into an adjoining mine owned by the same company. The pumping ceased on December 12. 2003, and the mine was allowed to flood. The water level rose about 17 m (55 ft) by August 3 1, 2004, based on observations in a nearby borehole. On September 3, 2004 surface subsidence occurred above this area causing damage 10 a residence (Figure 2).Summary of InvestigationThe floor of the Pittsburgh coal scam played a strong role in the pillar failure. In this area, the immediate floor of the Pittsburgh seam consists of about two feet of fireclay. Extensive damage to the surface house was an indication that a major collapse below the surface had occurred. The pillars supporting the overlying strata were evaluated to find the cause of their failure. The pillars in the Pittsburgh seam (sec Figure I) had a marginal safety factor of 1.15 before flooding and were stable for 26 years. Once the mine was flooded the water level in the Pittsburgh seam rose by 17 m (55 ft). Shortly thereafter the fireclay in the floor weakened, resulting in several pillars punching into the floor unevenly making the immediate roof unstable. The overburden strata supported by these pillars also subsided do"" n into the mine, causing damage to several house on the surface."

Jan 1, 2010

By Eugene D. Krupa

Mine 33 of Beth Energy has serious and complex roof cutter problems causing delay of the advance rate of both the entry development and longwall face retreat. The cost of maintaining these entries is very high due to the requirement of wry heavy artificial supports. It was suspected that this problem was caused by multiple factors including high in-situ horizontal stresses and weak roof in the problem areas. In order to alleviate the problem, proper design of panel entry and roof reinforcement were considered. This paper presents the results of extensive measurements in experimental panel entries of Mine 33 in order to assess the performance of the designed structure and roof support system during the entry development and longwall retreat. An experimental panel entry has been designed and implemented. The designed parameters were varied seeking for the most ideal parameters which provide stable roadways. Changing these parameters accompanied instrumentation of roof, floor, and pillars. Typical instrumentation, including stress meters, convergence measurement stations, and borehole borescope were utilued. Gnensive monitoring of the behavior of the designed structure and support system led to the development of a complete stress-deformation history of the roadway and an ideal roof reinforcement, support system, which reduced the cost of entry development by less than a third of the previous method.

Jan 1, 1990

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Amirhossein Molavi Tabrizi

In this paper we introduce a realistic model for mine openings that explicitly considers the effects of local irregular topography. Also, we consider the effect of entry orientation and rock anisotropy on the induced stress fields around mine openings under the given in-situ stress field. A triangular mesh formulation is derived for representing complicated irregular surface topography and underground openings. Each element contains three internal collocation nodes. Parts of the surface which are far from the mine openings are discretized by infinite elements. The rectangular infinite elements with three internal nodes are introduced specifically for this problem so they are compatible with the triangular elements. With the corresponding boundary element method (BEM) formulation, we then investigate the combined effect of the topography and entry orientation on the stress fields induced by openings in anisotropic rocks under in-situ stresses. A single rectangular opening in the anisotropic ground with topography and in-situ stresses is simulated using data from the Carroll Hollow mine in Ohio. The results of these simulations show that topography, rock anisotropy, orientation of the regional stress field and mine opening geometry all have appreciable effects on the stress fields around underground openings, yet these factors can all be accounted for in an efficient code with no need to discretize the model domain. Future applications using this new BEM formulation will provide useful guidance on selecting the optimal opening orientation in the mine in order to minimize undesirable stress concentrations around underground mine workings.

Jan 1, 2014

By Mostafa Sharifzadeh, Ebrahim Ghasemi, Kourosh Shahriar

"The Tabas Central Mine (TCM) is one of the underground coal mines located in the Tabas coal region, in the mid-eastern part of Iran. This mine is the first mechanized coal mine in Iran that uses the room and pillar method. Pillar design is one of the most important issues in underground coal mines, especially in room and pillar mining. In this paper, a new method for coal pillar design in the main panel of TCM is presented. This method is able to estimate the magnitude of the various loads (both development and abutment loads) that pillars might experience throughout the mining process. Also, the method reduces the pillar failure risk. Based on this method, proper pillar sizes in TCM are obtained (11.6 x 11.6 m (38.l x 38.1 ft)).INTRODUCTIONPillar design and stability are two of the most complicated and extensive mining problems related to rock mechanics and ground control subjects. Although these problems have been investigated for a long time, to date only a limited understanding of the subject has been gained. Prior to this, the dimensions of a pillar were largely determined by experience based on trial and error, intuition, or established rules of thumb; any research available tended to be isolated and sporadic. But nowadays, various pillar design formulas have been developed based upon laboratory testing, fullscale pillar testing, and back-analysis of failed and successful case histqries. In 1980, a number of ambitious field studies conducted by the U.S. Bureau of Mines developed the ""classic"" pillar design methodology. It consisted of three steps (Mark, 1999, 2006):1. Estimating the pillar load using tributary area theory2. Estimating the pillar strength using a pillar strength formula3. Calculating the pillar safety factorAlso, Bieniawski (1981) presented a step-by-step method to determine coal pillar dimensions in room and pillar mines. In this method, similar to the classic method, pillar load is estimated by using tributary area theory.Currently, in mqst of the room and pillar mines, remnant pillars in panels are recovered by retreat mining (pillar recovery). Hence, the above mentioned methods are not appropriate for pillar design, because in these methods pillar load is estimated by the tributary area theory, and the effects of abutment loads, which result from retreat mining and the creation of a mined out gob, are ignored. Abutment loads affect the pillars in the adjacent of pillar line and a load greater than what is estimated by tributary area theory is applied on the pillar. So, pillar design without considering the abutment loads leads to pillar failures during retreat mining. Pillar failures continue to be one of the greatest single hazards faced by underground coal miners. Pillar failures are responsible for unsatisfactory conditions, which include the following (Mark et al., 2003):"

Jan 1, 2010

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013

By Tim Miller, Michael M. Murphy, John L. Ellenberger, Gabriel S. Esterhuizen

"A limestone mine in Ohio has had instability problems that have led to massive roof falls extending to the surface. This study focuses on the role that weak, moisture-sensitive floor has in the instability issues. Previous NIOSH research related to this subject did not include analysis for weak floor or weak bands and recommended that when such issues arise they should be investigated further using a more advanced analysis. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to demonstrate the effect that a weak floor has on roof and pillar stability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface.IntroductionMassive roof falls extending to the surface at a limestone mine in Ohio have been studied collaboratively by the National Institute for Occupational Safety and Health (NIOSH) and the mine owners. This paper provides a summary of the sequence of events leading to observed instability and presents a numerical modeling analysis that investigates the role a weak floor can have on roof and pillar stability.This study builds upon previous NIOSH research in underground limestone mines undertaken by way of a survey that analyzed performance of pillars in 34 different stone mines in the Eastern and Midwestern United States between 2005 and 2009 (Esterhuizen et al., 2011). This survey led to the development of underground stone mine pillar design guidelines based upon a “stability factor” for the pillar system. The factor is compared to operational experience to determine ranges of values that are typical of stable pillar systems. A software package titled Stone Mine Pillar Design (S-Pillar) was developed for easy application of these guidelines (Esterhuizen and Murphy, 2011).Weak floor in the present case study departs significantly from cases included in the previous NIOSH research, in that none of the 34 study mines had weak floor issues. Moreover, this case study is the first in which a weak floor has been monitored routinely as roof falls are occurring. A detailed report on the observations and measurements taken at the mine has been published (Murphy et al., 2015). The previous observations led to the conclusion that although there were weak bands in the pillar, the weak floor was the significant defect that led to the instability issues. The pillars were initially mined in 2004, approximately 10 years before the instability issues began to occur. The objective of this study is to use numerical models to analyze a variety of floor strengths and the impact of moisture content to find the critical point at which the floor becomes unstable, leading to long-term instability issues."

Jan 1, 2015

By Kevin Jinrong Ma

Underground mines often experience roof falls in entries, crosscuts, and intersections of active mining sections, main travel ways, and belt entries. Roof fall heights greater than 20 ft (6 m) make re-bolting of the newly exposed roof dangerous and impractical. To protect mine personnel, belts, moving vehicles, and other facilities, mine operators typically install steel structures such as square or arch sets in the roof fall areas. Wood lagging is usually installed between the steel-sets to enclose the area and protect the entry from recurring falls. Usually the void space above the steel-sets and laggings is backfilled. However, backfilling high roof fall voids is costly, which causes some operators to leave the voids open. In this case, durability of wood over time and the capability of the steel-set and wood lagging to resist falling rocks are unknown. During the last few years, Keystone Mining Services, LLC (Jennmar Corporation affiliate engineering company) designed, tested, and developed an impact-resistant lagging system to protect steel-sets1. Various steel-sets protected with the impact-resistant lagging were approved by MSHA and installed in different underground roof fall rehabilitation projects. This paper presents (1) design, development, and laboratory testing of the patent-pending impact-resistant lagging panel, (2) steel-set design methodology according to the American Institute of Steel Construction (AISC) national standard, and (3) impact-resistant steel-set design method based on Law of Conservation of Energy. Two underground cases are reviewed to demonstrate the successful application of the impact-resistant lagging system.

Jan 1, 2011

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By K. Biswas

So far, all pillar design methods or approaches consider the coal seam as a uniform structure From some mine visits in northern Appalachian Region. it is found that some coal seams have binder or parting material within the coal scan with varying thicknesses and numbers- And it has also been found that these kinds of hinder materials tire prone to weathering when exposed to ambient mine moisture In this paper an attempt has been made to study the weathering susceptibility of parting materials and coal when exposed to moisture and a two dimensional finite element analysis has been carried out to study the effect of the presence of partings on the structural integrity of the coal pillar in terms of short-term and long-term stability.

Jan 1, 1995

By Christopher Mark

The Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. The study described in this paper was performed in a 1200 ft long, experimental headgate section which contained three pillar designs: - a three-entry, yield-abutment pillar' system, - a four-entry, yield-yield-abutment pillar system, and - a five-entry, all-yield pillar system. As the longwall mined by the experimental section, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The results of the study indicate that the all-yield system performed at least as well as, and probably better than, the two abutment pillar systems.

Jan 1, 1988

By Richard C. Repsher

The U.S. Bureau of Mines has developed a method and device designed to detect lose rock material in underground mines. The technology is designed to be an aid to mine workers in detecting hazardous roof conditions in underground mines which can complement or replace the traditional roof sounding techniques where the miner relies on experience to determine whether rock conditions are sound. The leading cause of accidents and fatalities in underground mines is falls of lose rock pieces or rock slabs from the mine roof. The device is an electronic roof sounding device that acoustically determines the integrity of mine rock. In previous research the Bureau of Mines found that loose rock, when impacted, vibrates at a much lower frequency than intact rock material. A major problem in determining rock stability using this technique has been the repeatability of the matt signal. This difficulty baa been greatly reduced in the current design by measuring the power spectra contained in two separate frequency bands of the signal produced by striking the rock in question. The ratio of the energy contained in each band is computed. This process minimizes any striking force differences, producing accurate, repeatable results for solid rock as well as loose, drummy material. The prototype has been successfully- tested in a variety of underground environments including coal, uranium, molybdenum, silver and salt. The technology has been investigated by the U.S. Mine Health and Safety Administration and the Department of Energy for use in detecting detached tunnel lining areas in nuclear repositories. The paper will discuss the technique, applicable results, and future applications.

Jan 1, 1990

By Kenneth Rigsby

Black Mountain Resources' Highlands Mine No. I is a full extraction room and pillar operation located in Harlan County, Kentucky. Black Mountain extracts the 0.9 to 1.1 meter (36- to 42-inch) thick Owl Scam that is situated 60 to 70 meters (200 to 235 ft) above the longwall panels of the abandoned Arch No. 37 Mine, in the 3.4 meter (I I ft) thick Harlan Scam. In the areas where full extraction has taken place, the overburden above the Owl Seam ranges from 60 to 430 meters (200 to 1,400 ft). A short room and pillar panel was developed above an extracted longwall panel to test the selected pillar size, to evaluate support systems, and to verify the shape of the subsidence profile over the recovery end of the depleted longwall panel. It is over the recovery end that Highlands Mine No. I would access the Owl Seam reserves that exist above the No. 37 Mine. Black Mountain selected pillars sizes to be employed above the longwalls based on the ability to fully extract a pillar employing extended cuts. After a mechanical testing program was completed and mine behavior and top disturbance were observed in the test panel, John T. Boyd Company (BOYD) verified pillar stability and designed support systems. BOYD previously designed No. 37 Mine's gate pillars and studied subsidence and gob formation over its longwall panels; this effort aided the analysis of overburden movement and pillar integrity at Highlands Mine No. 1.

Jan 1, 2003