Search Documents

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has' been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

By A. El-Midany

Dolomite impurities are increasing in the currently mined phosphate deposits in Florida. Several research efforts have been conducted in various laboratories around the globe to find methods to economically removing the dolomite. However, a universal and cost-effective process is not now in commercial use. In this paper, a new process for dolomite/apatite separation is presented. The differential solubility of dolomite in slightly acidic solution is utilized to generate micro CO2 bubbles at the dolomite/water interface. Particle (dolomite)/bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro-bubble/particle aggregates. Different surface-active agents were tested to stabilize the bubbles. Results of these tests are presented, and the mechanisms involved are discussed.

Jan 1, 2009

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By Niels Kofoed

Upon completion of the 6,200 m (20,340 lineal ft; lft) North Tunnel drive for the Portland East Side Combined Sewer Overflow (CSO) Tunnel project in Portland, OR, the slurry tunnel boring machine (TBM) had to be returned from the Port Center shaft at Swan Island to the Opera shaft at the main mining site for the 2,700 m (8,860 lft) South Tunnel drive. At the Port Center shaft, the main 513-t (565-st) TBM and TBM tailshield were hoisted out of the shaft in two pieces using four 200-t (220-st) strand jacks mounted on a 635-t (700-st) hydraulic boom gantry system supported by Emmert International?s custom gantry tracks designed to span the shaft. After lifting the TBM components out of the shaft, the gantry system loaded the TBM components onto two Goldhofer platform trailers, which then transported the TBM and tailshield to a barge using a roll-on/roll-off method.

Jan 1, 2011

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By A. T. Iannacchione

From 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig.1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig. 2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91%, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from1990 to 1996. This number is not large in magnitude. But a workforce of fewer than 2,000 miners makes for a high fatal-accident rate. The severity of the typical fall-of-ground injury is, in general, very high. About three-fifths of all roof, face and rib fall injuries were designated by the US Mine Safety and Health Administration (MSHA) as some kind of lost time accident. MSHA assigns each accident a severity value from one to six. A one represents a fatality, a two, a permanent disability and three, a lost time accident (Fig. 3).

Jan 1, 2000

By G. R. Robinson

Aggregate resources consist of sand and gravel, and crushed stone. They are large-tonnage, bulk-minable mineral commodities that are used in construction and industrial activities (Tepordei, 1999, 2001).Rates of aggregate production, use and mine permit approval in the mid-Atlantic region differ by population density. These rates are influenced by economic and human factors, such as demand, costs, land availability and community opposition. In some areas, the local availability of aggregate is limited. This is due to the lack of suitable local source materials for aggregate, the loss of potential high-quality aggregate resource production sites by preemptive land development and restrictive zoning (resource sterilization), and the difficulty of developing and permitting production sites for aggregate.

Jan 1, 2004

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

By B. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 2005 at a record $758 million (21 percent of the total non-fuel mineral production of Utah). Major commodities produced in 2005 include salts (halite, potash, and magnesium salts), Portland cement, sand and gravel, carbonates (lime, limestone, and dolomite), phosphate, crushed stone, clays, lightweight aggregate (expanded shale and perlite), gypsum, silica, sulfur and sulfuric acid, and building stone. Commodities produced in smaller amounts include diatomite, pumice, gemstones, ornamental stone, fluorspar, and mineral and fossil specimens. Utah is in a period of rapid growth in industrial rock and mineral production; however, some commodities have grown faster than others. The robust western economy has stimulated production of construction-related commodities like sand and gravel, Portland cement raw materials, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants

Jan 1, 2007

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

By Russel Delmar, Rick Everdell, Harry Charalambu, John Tait

Award of the Design/Build Agreement for construction of Ontario Power Generation’s (OPG’s) Niagara Tunnel Project was made after an intensive 8-month international procurement process. The 14.4-m diameter × 10.4-km long rock tunnel will divert 500 m3/s of water from the Niagara River to the Sir Adam Beck hydroelectric generating complex. The procurement process and Design/Build Agreement included features to address the owner’s requirements regarding risk allocation and cost and schedule certainty, while encouraging innovative ideas from the industry, both technically and commercially. The process included an international expression of interest and prequalification, followed by an invitation for design/build proposals to qualified proponents, and comprehensive proposal evaluations and negotiations with several respondent proponents. An honorarium was provided to the unsuccessful participants in the proposal stage. The resultant negotiated Design/Build Agreement includes Owner’s Mandatory Requirements, negotiated contract terms and conditions, performanceincentive bonuses and liquidated damages for schedule and water delivery performance, a multistaged Geotechnical Baseline Report, joint risk management, references to preexisting community impact agreements and measures to reduce impact on tourism. It also addresses regulatory approvals and permits, an owner controlled insurance policy that required reference to the International Tunneling Insurance Group (ITIG) Code of Practice for Risk Management as a condition of coverage, site specific safety, security and environmental plans, formal team building, a dispute review board, and escrow documentation.

Jan 1, 2007

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.