Search Documents

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By Peter Amelunxen, Kain Nugent, Brandon Akerstrom, Willem Duyvesteyn, Todd Harvey

In 2024, Capstone Copper Corp commissioned a new sulfide flotation plant at Mantoverde in the Atacama region of Chile to process copper ore at a design rate of 32,000tpd. The pyrite associated with the copper ore body contains cobalt in solid solution, with Co replacing Fe in the pyrite matrix. As per the existing sulfide flotation flowsheet most of the pyrite is depressed and sent to tailings via the cleaner scavenger tail stream. A new project considers the recovery of the pyrite from the cleaner-scavenger tails via froth flotation to produce a cobaltiferous pyrite concentrate, which is then leached via the existing dynamic copper leach pad to oxidize the pyrite and dissolve the cobalt. The cobalt is recovered from the solution by treating a bleed stream of copper SX raffinate through a continuous, counter-current ion exchange (CCIX) facility. This approach to by-production of cobalt confers numerous benefits, including reduced costs compared with alternative cobalt recovery processes, reduced acid consumption in the heap leach, increased copper production, and reduced acid mine drainage potential due to the removal of pyrite from the mill tailings.

Feb 1, 2025

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

Conditional simulation provides a model of the ore body that represents variability in the data. This can be used to determine the impact of various grade control and mining strategies. A number of transfer functions are discussed that assist in optimizing grade control sampling. The cost effectiveness of various drilling and trenching techniques are discussed. Modelling of the expected performance of a mill head grade sampler is investigated. Conclusions are drawn about the likely impact of various sampling techniques on the economic performance of an operation and about applying sampling theory to grade control sampling.

Jan 1, 1999

By J. S. Hall

The performance of a full-scale balling drum circuit is well known to fluctuate, and is difficult to control. The fluctuations stem from causes that are not readily quantifiable. Results from plant tests show that surging of the recycle tonnage is dependent, inter alia, on the method of bentonite addition, small variations in drum or cutter bar speed and the method of drum water addition. This paper presents detailed observations from experiments on full-scale drum circuits, including preliminary results of a computer measurement and control scheme. Size distributions measured at points along an industrial drum are presented, together with the results of a mathematical model fitted to one plant data set. Model predictions are also included emphasizing the importance of screen performance on circuit stability.

Jan 1, 1983

By A. G. Kim

Increasing transportation costs, clean air regulations and the decreasing availability of landfill space are factors in the increased interest in the utilization of low cost disposal sites for coal combustion residues (CCR). Inactive surface and underground coal mines can satisfy the conditions for stable CCR disposal sites, and subsurface CCR injection can be beneficial in reducing the amount of acid mine drainage (AMD) often produced at such sites. The material is expected to add alkalinity to the subsurface environment and to decrease the permeability and porosity of the buried spoil. Both mechanisms can reduce the amount of acid normally generated at a mine site. The Bureau of Mines is cooperating with an independent coal company in a test of subsurface injection of a mixture of fly ash, from conventional power plants or from fluidized bed combustion (FBC) , with AMD sludge into a reclaimed surface mine. Changes in water quality parameters and the concentration of heavy metals in water samples from wells and seeps are being used to assess the effect of CCR injection. The preliminary results discussed here indicate that improvement in subsurface water quality was related to fly ash injection and that components of the fly ash were stable in the acid environment.

Jan 1, 1994

By Weijian Yu, Jianbiao Bai, Jinlin Xin, Shiqiang Xu, Shuai Yan, Zizheng Zhang, Hai Wu

The retained roadway subjected to dynamic loading from thick and hard roof (THF) fracturing caused severe deformations in the thick coal seam (TCS). Understanding the dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF is the first step in determining the stability of the retained roadway. Characteristics of dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF are investigated through numerical simulation and field test of 150208 haulage gate in Sucun coal mine. To improve the reliability of numerical simulation, the double-yield model is used to simulate gob and the strain-softening model is used to simulate filling body; the dynamic module in FLAC3D is used to simulate the dynamic loading due to the THF fracture, and the global model are validated. Characteristics of surrounding rock convergence, plastic zone distribution, and vertical stress in the filling body after the THF fracture are reveled with respect to width to height ratio (W/H) of the filling body and the dynamic loading strength of the THF. The rational width to height ration of the filling body constructed with high-water materials is 0.57. Field monitoring results show that the GER with THF in Sucun coal mine could adapt the dynamic loading due to the THF fracture and meet the requirement. This study is helpful to better study the stability of GER according to the breaking dynamic load of THF and provides reference and guidance for the analysis of breaking dynamic load of THF under similar geological conditions.

Feb 23, 2023

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By Rusty Winn

"R.E. Janes Gravel Co. is an aggregates producer is located along a paleo-channel of the Ogallala formation (locally known as the Slaton Channel) approximately 48.3 km (30 miles) southeast of Lubbock, TX. In an attempt to beneficiate the 25.4-mm (1-in.) concrete aggregate product, a log washer was installed in the processing line to liberate and remove fines (clay) from the finished product. The introduction of this extra cleaning step increased fines in the finished product, exacerbating the original problem. Several other processing options were investigated before a geological analysis was undertaken to try and define the lithology of the formation and formation characteristics in an attempt to alleviate this problem.Initial assessmentsThe mined resources are mid-Miocene to early Pliocene (16-4 mya) in age and is the eastern exposure of the Ogallala formation of the Southern High Plains escarpment. The Ogallala formation consists of coarse-grained alluvial sediments in paleovalley channel ways from the Rocky Mountains with fine Aeolian and paleosol deposition on the uplands across the High Plains region of the United States. Locally, these Rocky Mountain sediments from New Mexico were transported and deposited in a paleochannel that is approximately 0.805 km (0.5 miles) wide and 15.25 to 18.3 m (50 to 60 ft) in depth. As this channel cut across the Southern High Plains it eroded local rock sources of Late Cretaceous limestones and Triassic sandstones and mudstones incorporating them into the younger Ogallala depositional sequence.Depositional historyThe channel currently being mined is a nontypical Ogallala deposit. The Ogallala in the panhandle of Texas is divided into two units, the Couch and the Bridwell. The Couch is the older of the two and exhibits alluvial sedimentation of thicker and larger gravel (up to 76.2 mm or 3 in.) deposits fining upward to Aeolian sedimentation and thick friable caliche deposits. The Bridwell overlies the Couch and is characterized by alluvial sedimentation, a distinctive red tint and smaller gravel components (typically no larger than 25.4 mm or 1 in.) fining upward to Aeolian sedimentation and thick, well-indurated caliche cap. The Slaton Channel divides these two units and shares lithologic components of both, yet is lithologically distinct due to its Cretaceous Age limestone gravels that can be < 3.66 m (12 ft) in size. Caliche/calcrete is a calcareous (CaCO3) deposit that forms in the B horizon of soils as a rain water leachate of CaCO3 from the upper A horizon."

Jan 1, 2014

By S. A. Saki, J. F. Brune

"INTRODUCTION Longwall coal mining leaves large areas where the coal has been made removed and the roof rock strata collapse, forming a zone of broken rock rubble called the gob. Figure 1 shows a typical longwall gob area along with the gate roads. The ventilation pattern for progressively sealed longwall panels follows a simple “U” pattern where fresh air is coursed inby to the headgate, flows along the face and exhausts through the outby tailgate as shown in figure 1(a). An important variation of this pattern is the back return (BR) arrangement where the exhaust air from the face is drawn inby and around the nearest open cross cut before it turns in the outby direction towards the exhaust fan. Figure 1(b) illustrates the use of back return. This arrangement moves the point of low pressure from the tailgate corner up to 60 m inby and thus maintains fresh air in the tailgate region that could otherwise be contaminated with gob air.The gob area may contain remnants of unmined coal or parts of overlying coal beds that continue to release methane, eventually filling the gob area with methane in concentrations far above the explosive range of about 4.5 to 15%. Many gob areas must be equipped with gob ventilation boreholes (GVBs) to extract methane, and GVBs often exhaust methane at concentrations from 50% to 90% (Saki, 2016). Due to oxidation processes occurring in the gob, the oxygen content is reduced to a low level, with nitrogen and CO2 making up the major remaining components of the gob atmosphere. FORMATION OF EXPLOSIVE GAS ZONES IN GOBS Since the longwall face area is ventilated with fresh air below 1% methane and the face and gob areas are not separated, an explosive fringe will form where the methane content lies within the explosive range and oxygen content remains above 12%. Figure 2 shows a typical development of such an EGZ. This figure is based on a computational fluid dynamics (CFD) model developed by CSM researchers to analyze gas concentrations and flow patterns in longwall mining. Figure 2(a) shows the formation of EGZ in the gob with a U type ventilation scheme, where EGZ lies right behind the shields in the tailgate corner. Figure 2(b) shows the formation of EGZ in the gob combining U type ventilation scheme with BR, where EGZ is pushed away from the face deep into the gob. The CFD modeling parameters and boundary conditions have been verified with field data from two cooperating, active longwall mines (see Worrall 2012, Marts 2015, Gilmore 2015 and Saki 2016). Other mine geometries, methane inflow rates and gob permeability distributions can be modeled to establish representative gob atmospheric conditions. Two GVBs were operating in the model, extracting 0.165 m3/sec each. The methane in the working areas and returns was kept below 1%. Methane flowing into the model from a rider coal bed above the mined seam was at the rate of 0.55 m3/sec."

Jan 1, 2017

By Robert T. Chapman

Many of us are privileged in that we have witnessed the transition from mining methods used in the first quarter of the twentieth&apos; century to those practiced today. In the late Twenties, for example, many mines still used hand mucking methods. In the middle Thirties, more than one large metallurgical limestone quarry still used the 4 cubic yard railway steam shovel formerly in use at the Panama Canal. Mules could occasionally still be found underground, where they provided the-main-source of motive power. Within the last decade, and even within the past five years or less, great improvements have been made in blast-hole drilling, ore loading, and ore hauling equipment. Industrial demand for minerals can be expressed in exponential terms as compared to that at the turn of the century. Even marine mineral resources are receiving accelerated attention. One overall result is that larger and lower grade orebodies can be exploited at a profit. This profit must be made despite, for example, a static monetary price for gold, and despite the continual cost escalation involving labor, materials, supplies, and equipment. Accordingly, the application of the necessary degree of knowledge and judgment required to meet production, cost, and profit goals is paramount.

Jan 1, 1966

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By K. V. K. Prasad

Forecasting mined grade variability from exploration information is a challenging task in mine planning. For effective planning of activities such as workplace scheduling, ore grade quality control etc. development of realistic numerical/simulation models of in-situ variability from exploration information is an essential first step. Geostatistical conditional simulation (GCS) is one of the well known methods to develop these simulations. Recently, stochastic fractal models based on the assumptions of scale-in variance and self-similarity have been used for developing simulations of several natural phenomena. It has been suggested that these models might permit generation of short-scale variability information from exploration data with greater fidelity when the data satisfies the attendant assumptions. In this paper the stochastic fractal models are reviewed and their relationship to geostatistical variogram models is examined. A comparison of the two simulation techniques has been per-formed using coal sulfur data from a mined out coal property. The results of this comparative analysis are also presented in the paper.

Jan 1, 1992

By Ronald P. Geitgey

Pumice and volcanic cinder are volcanic rocks characterized by a cellular structure. They are formed as gases (primarily water) dissolved in molten rock, or magma, exsolve to generate a froth that cools and solidifies into rigid foam. The cells or bubbles are referred to as vesicles and they range in size from a few thousandth of a millimeter to several centimeters. Due to their vesicular character, both pumice and cinder have lower density and higher porosity than most other rock types, and, as the vesicle walls are broken, sharp cutting edges are continually generated. These properties are the basis for their commercial value as lightweight aggregates, insulators, absorbents, and abrasives. There is a certain imprecision in the terminology applied to volcanic products, reflecting to varying degrees the diversity of volcanic rocks, the relative youth of volcanology as a distinct field of study, and customs and practices of commercial trade. In general terms, pumice is light colored (white, gray, pink, pale yellow, or brown) and highly vesicular, usually with vesicle walls that are visibly glassy. Many pumice fragments are light enough to float on water. Pumice is readily cut by steel tools and some can be crushed by hand. Individual pumice fragments may range from 1 or 2 m in one dimension to c1 mm. Commercially, finer fragments are called pumicite or volcanic ash. In volcanology the term ash refers to any fragment c2 mm in size regardless of its composition. Cinder, or scoria, is dark colored (black, red, brown) with thick vesicle walls that appear dull or stony and that may exhibit iridescence. Cinder typically is heavier than pumice and has a higher crushing strength. In volcanology the term scoria refers to dark vesicular material throughout a wide size range while it is common commercial practice to use scoria for larger fragments (usually greater than 2.5 cm) and cinder for smaller fragments. GEOLOGY Composition and Physical Characteristics Most pumice is silicic ranging from 60 to 70% SiO2, that is, dacitic to rhyolitic in composition. Pumice of less silicic composition, including basaltic, occurs but it is less common and does not have extensive commercial use. Scoria and cinder are typically basaltic to andesitic with approximately 50 to 60% SiO2. Pumice and cinder may contain phenocrysts of feldspars and various ferromagnesian minerals that crystallized in the magma prior to eruption. Fragments of rock through which the magma has passed may be entrained in the melt and wall rock may be fragmented and admixed during an explosive eruption. Some scoria particles have lithic fragment cores. Phenocrysts and lithic fragments are relatively unimportant in cinder end uses but their presence may be detrimental in certain pumice products. Pumice typically has vesicles <1 mm in size separated by thin walls. Vesicle shapes include irregular, spherical, elliptical, and elongate to the point of being tubular with a silky appearance (Fig. 1). In some pumices, the vesicles are interconnected making the fragments permeable and highly absorbent; in others the vesicles are isolated forming a highly porous but very impermeable pumice. Floating masses of pumice fragments from the eruption of Krakatoa in 1883 were reported in the Indian Ocean for up to two years after the eruption. Vesicles in cinder are larger and range from spherical to highly irregular in shape with much thicker walls and abundant interconnections. Scoria and cinder are typically heavier, porous, and do not float. Density and hardness of pumice must be expressed precisely to avoid confusion. Density may refer to the glass itself, the apparent density of the vesicular pumice particle, or the bulk density of pumice in a deposit or in a product. Pumice glass has a specific gravity of 2.5 or more depending on its composition. Pumice fragments typically have a specific gravity of 4.0 and so will float on water, at least until enough vesicles are saturated to cause them to sink. Expressed as density, pumice fragments typically weigh less than 1 g/cm3. Depending on moisture content, particle density, and particle size distribution, the bulk density of pumice typically ranges from 500 to 700 kg/m3. Typical bulk densities of cinder range from 700 to 900 kg/m3 for material used as lightweight aggregate while the bulk density of cinder used for highways and railroad ballast may be considerably higher. Hardness in pumice may refer to the glass vesicle walls, possibly including crystals or lithic fragments, or to the apparent hardness of the particle as a whole, which is more a measure of the strength of the vesicle structure. Pumice glass typically has a Mohs hardness of 5 to 5.5. A pumice particle may have a much lower apparent hardness and be easily cut with a knife or steel saw because the vesicle walls break readily. Pumice and cinder are primarily pyroclastic deposits formed as fragmental products of volcanic eruptions. Several classification - systems differing in various details have been proposed for pyroclasts and pyroclastic deposits based on particle size (Fisher, 1961, Schmid, 1981, Cas and Wright, 1988). Generally, particles >64 mm are referred to as blocks or bombs depending on their shape. Particles between 64 mm and 2 mm (4 mm in some schemes) are called lapilli and smaller particles are called ash. These names may be modified by compositional terms, for example pumice lapilli or scoria lapilli. Most commercial deposits are composed of fragments in the lapilli size range. In the United States, pumice fragments having one dimension of 5 cm or more are legally defined as block pumice. The procedures for acquiring pumice from federal land are determined in part by this definition and are described in a later section.

Jan 1, 1994

By H. T. Mulryan

Talc is used as an essential ingredient in a wide variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance, and household furniture components to high performance parts made from liquid crystal engineering resins. The paper focuses on polyolefin applications; the three tier market for talc in polypropylene; the effects of various talcs in typical compounds; and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds which mimic higher cost resins, and polyethylene films, customer requirements for talcs for these purposes are discussed.

Jan 1, 1993

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By Yi Luo, FENGLIANG WU

Mine gob has long been a safety concern in the coal industry due to the air flowing through the gob area. Therefore, knowledge of the airflow distribution and locations of hazard zones in longwall gob is important to prevent and control these hazards. Due to the inaccessibility of mine gob, many numerical studies have been performed to simulate gob air leakage using computational fluid dynamics (CFD) programs, but most of the studies isolated the gob from the mine ventilation network (MVN) with only predefined pressure boundary conditions. The MVN is, in fact, not static in a dynamic longwall mining process, and it consequently changes the boundary conditions and the gob flow field (GFF). Therefore, the MVN should be incorporated in the CFD model to prescribe the transient boundaries. However, it is very challenging to couple the 1D MVN and the 2D/3D GFF to make the mine ventilation simulation realistic. This research uses a proposed novel finite tube method (FTM) to couple the MVN and GFF. In the FTM, the GFF is discretized into a finite number of flow tubes, each of which is formed by two adjacent streamlines. These tubes connect the MVN into a new coupling network. Based on the FTM, a model for gas migration in gob is established for delineating the hazard zones of explosive methane concentration and spontaneous combustion.