Search Documents

Your assessment of the minerals business. The global mining industry is strong. I am convinced it will continue meeting the mineral needs of the world population for the foreseeable future. Two developments have greatly enhanced the industry’s ability to produce low-cost minerals. Technological innovations have resulted in increased productivity. And there has also been a dramatic expansion of the number of favorable countries in which to explore and mine. Capital expenditures have flowed to the low-production-cost mines and development projects as well as to the exploration projects and stable countries having the best potential for valuable mineral discoveries.

Jan 1, 2000

By W. D. Bachman

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from Kennecott Copper Corporation's Chino mine. The efficiency with which the various samples could be ground was found to vary over an extremely wide range, even among samples taken from different locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale non-homogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully.

Jan 1, 1970

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

To gather additional field data from the western United States, researchers from the National Institute for Occupational Safety and Health (NIOSH) installed an array of field instrumentation at a longwall coal mine in Central Utah. The purpose of this field site was to monitor ground movement and changes in pressure during mining where conditions include massive, stiff overburden and relatively deep cover. To accomplish this, field instrumentation was installed in the two-entry gate road between the fifth and sixth longwall panel in the current mining district.

Jan 7, 2020

By Laurens de Jonge, Wiebe Boomsma, Rodney Norman, Stanislav Verichev

"Earth provides natural resources, such as fossil fuels and minerals that are vital for human life. As the global demand grows, especially for strategic minerals, commodity prices rapidly rise. Thus there is an identifiable risk of increasing supply shortage for minerals. Hence a major element in a long-term economic strategy must be, to ensure security of supply for these strategic minerals. In this rapidly changing global economic landscape, deep sea mining has gone from a distant possibility to a likely reality within just a decade.Although deep sea minerals extraction was investigated in the 1970’s, it was abandoned because of changing commodity economics, advances in on-land exploration techniques, growing concern on environmental impact, and political and legal aspects with regard to ownership issues. The developmental data from those days, if still available, are not adequate to allow engineering and building of an integral system for extraction of deep sea minerals without additional R&D work. Thus, deep sea mining is yet to attain a Technology Readiness Level (TRL) sufficient to successfully undertake deep sea mining operations, from resource discovery to resource assessment and to resource exploitation [Blue Mining, 2014]."

Sep 1, 2014

By Natalia Konstantinova, Georgy Novikov, Pavel Rekant, Goergy Cherkashov, Olga Bogdanova

The economic interest of oceanic ferromanganese crusts and nodules is determined by high grades of major, rare and earth rare elements in these types of marine minerals [1]. Modern oceanic ferromanganese deposits have a global distribution with the largest fields in the Pacific Ocean. The Arctic Ocean still remains a poorly explored region. The first ferromanganese deposits from the deep part of the Arctic Ocean were recovered almost at the same time in 2012 both in US and Russian cruises to the Chukchi Borderland (1) and Mendeleev Ridge (2). Preliminary results of mineral deposits from the first area were reported at UMI-2012 by James Hein et al. [2]. We present here the data of ferromanganese deposits from the Mendeleev Ridge.

Sep 1, 2014

By J. C. Potvin

Although the occurrence of deposits of titanium minerals on Kenya’s present day beaches and adjacent dune systems has been well documented, the potential for older formations to host economically viable deposits had not been recognised until recently. The Magarini sands formation in Kenya has been found to contain deposits of ilmenite, rutile and zircon in quantities and grades that have the potential to be commercially exploited. Since 1995, Tiomin Resources Inc. has explored these deposits and has identified one deposit, the Kwale project, as being able to support the development of a mine producing some 300,000 tpa ilmenite, 75,000 tpa rutile and 37,000 tpa zircon. Tiomin plans to start production by late 2002. Construction of a US$137 million operation is set to commence in the first half of 2001.

Jan 1, 2001

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By C. O. Lee

The Grand Isle Sulphur Mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, Louisiana. The depth of water at this location is about 50 feet. The deposit is on acreage covered by oil, gas, and mineral leases which were originally issued in favor of Humble Oil & Refining Company by the State of Louisiana, and which were continued, maintained, and redesignated by the Department of the Interior of the United States, pursuant to Section 6(b) of the Outer Continental Shelf Lands Act. On September 19, 1956, Freeport Sulphur Company acquired from Humble Oil & Refining Company the sulphur rights underlying the tracts. This assignment was approved by the Secretary of the Interior on July 12, 1957. The Director, United States Geological Survey, approved Freeport Sulphur Company as Operator on July 31, 1957. Actual design began in September 1956; the first structural contract was let December 15, 1957, and offshore erection began in June 1958. The initial phase of construction will be completed and production started in early 1960. The estimated total cost of the project is $30,- 000,000, of which $8,000,000 is the extra cost for being in the Gulf of Mexico.

Jan 1, 1959

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By M. L. Tucker, William H. Langer

Many countries, provinces, territories and states in the European Union, Australia, Canada, the United States and elsewhere have begun implementing sustainability programs. Most of those programs, however, stop short of sustainable management of aggregate resources. Sustainable practices do not always have to be conducted under the title of sustainability. This case study describes how Lafarge implemented the principles of sustainability even though there was an absence of existing local government policies or procedures addressing sustainable resource management. Jefferson County is one of three counties in the six-county Denver, CO, region that has potentially available sources of crushed stone. Crushed stone comprises 30percent of the aggregate produced in the area. And it plays a major role in regional aggregate resource needs. Jefferson County is home to four of the five crushed stone operations in the Denver region. Lafarge operates one of those four quarries.

Jan 1, 2004

By J. D. Doll

MSHA has promulgated a rule to limit the exposure of underground metal/nonmetal miners to diesel particulate matter (DPM). In May 2008, the final personal exposure limit will be lowered to 160 µg/m3 total carbon. To comply with this rule, mine operators are implementing a variety of control technologies. In this study two types of control technologies (ventilation and cabs) which are being implemented in limestone mines were investigated. Two stone mines in this study use large diameter propeller fans for main mine ventilation and direct the air to the faces using auxiliary fans, stoppings, and long pillars while bypassing the old mine workings. NIOSH measured for sub-micrometer elemental carbon (EC) using SKC DPM cassettes (analyzed using NIOSH 5040) and a near real time instrument. With the present ventilation and the number and type of vehicles used, the concentration of EC from DPM at the working areas was at or below 400 µg/m3 for both mines and about 166 µg/m3 and 251 µg/m3 at the returns. The real time data showed that the ventilation was reaching the working areas and effectively diluting the DPM. Environmental cabs were also used to reduce DPM exposures in three underground limestone mines. Using NIOSH method 5040 and near real time EC instrumentation, NIOSH sampled inside and outside of a loader cab at one of these limestone mines to determine the effectiveness of the cab. The cab was found to be over 90% effective in removing DPM as long as the cab system was properly maintained, and doors and windows were closed.

Jan 1, 2009

By Robert W. Yokom

As the search for new sources of energy and minerals leads to more remote areas of the country - and the world - the need to plan for adequate housing and community facilities for the construction and operations workforces and their families takes on an importance equal to the mining and processing facilities themselves. A corollary to the need for planning is the increasingly crucial need for development companies to devise effective strategies for dealing with the local communities impacted by these projects. Experience has amply demonstrated the high price to be paid for failure to learn this lesson, a price measured in lost productivity, confrontation with local communities, labor turnover, mental health and other social and eocnomic problems. In Sweetwater, Wyoming, a new industrial activity caused the population to double from 18,000 to 36,000 between 1970 and 1974. During that period industrial productivity fell 25 to 40 percent, cost overruns on the principal new industrial facility exceeded 33 percent, annual employee turnover rates climbed above 100 percent, the local mental health clinic workload increased nine times and complaints to the local law enforcement agency increased 60 percent.

Jan 1, 1981

By M. J. Farrell

The threat of global warming and its prominent position in public discussion and political debate requires all industry to take stock of its contribution to rising atmospheric concentration of greenhouse gases. For the primary metals industry, the first step must be to identify the pattern and range of emissions at each step in the production chain. Only then can the industry assess the economic consequences of the penalties on emissions that will be imposed by governments and regulators and devise cost-effective plans to avoid or mitigate such penalties. While some work has been done to estimate carbon dioxide (CO2) emissions using Life Cycle Inventory analysis, this approach is less useful than site-by-site emissions estimates. It is the level of specific emissions at each site that will ultimately deter-mine carbon taxation liabilities and participation in emissions trading schemes. Most mining companies have moved with the times to issue sustainability reports for their operations. But in the absence of any standardized reporting format, it is difficult to make useful comparisons between even the best-reported producers on a like-with-like basis. For this reason, Minecost.com modeled the use of fuels and energy used in mining, milling, shipping and metallurgical treatment to cover ?cradle-to-gate? emissions of greenhouse gases resulting from the production of the major base metals copper, zinc, lead and nickel. Greenhouse gas emissions ? overwhelmingly carbon dioxide ? are associated with the consumption of energy at every step in the production chain, from exploration through mining to the production of refined metal. Producers of primary metal employ diverse technologies to mine, mill, smelt and refine several different types of ore. Every orebody has its own special characteristics. In addition, most base metals are produced in concentrate that must be transported to smelters, with con-sequent emissions consequences.

Jan 1, 2009