Search Documents

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By B. Z. Weiss, N. R. Comins, F. Blum

The effect of microstructure on the deformation and fracture properties of 3CR12 steel was investigated at different strain rates in the temperature range -196 to 200°C. The yield stress of the as-received steel, showing a banded dual-phase microstructure, was much lower than that of the flake-like dual-phase microstructure produced by heat treatment. The heat treatment also resulted in an increase in the volume fraction of martensite. The fracture toughness of the as-received 3CR12, on the other hand, was significantly higher than that of the heat-treated material. These changes in both yield stress and fracture toughness were attributed to the effect of microstructural parameters on the constraints imposed on the deformation and subsequent failure of the ferritic phase in the as received and heat-treated steels. The exceptionally low resistance to crack extension in a plane parallel to the roiling plane of the as-received material was ascribed to the delamination process, which is typical for controlled-rolled steels. The yield stress and fracture toughness were found to depend on temperature and strain rate. The appearances of the fracture surfaces were found to be consistent with the mechanical properties.

Jan 1, 1992

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By J. M. Stewart

Mining fatality rates in many countries have not changed substantially over the past ten years. This demonstrates not only that there is an inherent risk in mining, but also that current approaches to improving safety need to be rethought. An analysis of productivity and fatality data in the United States, United Kingdom, and South 4frican coalmining industries shows that the impact of legislation on safety is overlain by other significant factors. Although improvements in safety and productivity usually occur together, the data warn that safety legislation can sometimes cause a significant reduction in productivity. Based on the data and experience considered, it is concluded that legislation should be aimed at creating a framework within which a positive attitude towards the implementation of more productive and safer mining methods, work practices, and technology can flourish, rather than attempting to enforce excessively prescriptive provisions. This later approach is even more problematic when safety standards and legislation are transferee from well developed to less developed countries. A legislative framework in which the mine manager is required to take al reasonably practicable measures to procure safe working conditions in accordance with mine-specific codes of practice is outlined. Within that framework, the value of adopting widely accepted standards is recognized. A performance-based external audit arrangement is outlined as a basis for ensuring that detailed attention is focused on those areas most needing improvement.

Jan 1, 1995

Brigadier R. S. G. Stokes of Sherborne, Dorset, is the oldest surviving member of the South African Institute of Mining and Metallurgy. He joined in 1904 and has been a member for 77 years. Book review Sittig, M. Hand book of catalyst manufacture. Park Ridge (U.S.A.), Noyes Data Corporation, 1978. The detailed information in this book is based on patents issued in the U.S.A. that deal with catalysts and their commercial technology. Project management The South African Institute of Mining and Metallurgy is to hold a Colloquium on Project Management in the Metallurgical Industry in March 1980. Ingenieurs-in-opleiding in die weermag Op 'n onlangse vergadering van die Suid-Afrikaanse Raad vir Professionele Ingenieurs is daar besluit om kwytskelding van jaargeld aan geregistreerde ingenieursin- opleiding wat tans met hulle tweejaar nasionale diensplig besig is, te verleen met dien verstande dat.... Engineers-in-training in the army At a recent meeting of the South African Council for Professional Engineers it was resolved that a remission of annual fees would be granted to registered engineers in- training who are doing compulsory two-year national service, provided that.... Processing of fine particles The Society of Mining Engineers of AIME is organizing an International Symposium on Fine Particles Processing, which is to be held in Las Vegas from 24th to 28th February, 1980. Economics of precious metals International Precious Metals Institute announces a Special Course for all interested in economic aspects of today's precious metals.

Jan 1, 1979

Abstract A new approach is introduced for study of the behaviour of geotechnical strength parameter prior to slope analysis to ascertain whether strength parameters of slope materials are homogenous or heterogeneous at different mine depths. The strength parameters used for the study are uniaxial compressive strength, tensile strength and shear strength. The analysis is based on statistical analysis of variance technique for one-way classification. The application of the technique is given through a case study in an openpit mine. Auszug Eine neue Annäherung wird für Studie des Verhaltens des geotechnischen Stärke Parameters vor Steigunganalyse eingeführt, um zu ermitteln, ob Stärke Parameter der Steigungmaterialien homogenous oder an den unterschiedlichen Grube Tiefen heterogen sind. Die Stärke Parameter, die für die Studie verwendet werden, sind einachsige zusammenpressende Stärke, Dehnfestigkeit und Scherstärke. Die Analyse basiert auf statistischem varianzanalytische Technik für Einwegklassifikation. Die Anwendung der Technik wird durch eine Fallstudie in einer openpit Grube gegeben. Abstrait Une nouvelle approche est présentée pour l'étude du comportement du paramètre géotechnique de force avant l'analyse de pente pour établir si les paramètres de force des matériaux de pente sont homogenous ou hétérogènes à différentes profondeurs de mine. Les paramètres de force utilisés pour l'étude sont résistance à la pression uniaxiale, résistance à la traction et résistance au cisaillement. L'analyse est basée sur statistique la technique de l'analyse de variance pour la classification à sens unique. L'application de la technique est donnée par une étude de cas dans une mine à ciel ouvert.

Jan 1, 2003

By D. G. Krige

Using a very large number of chip-sample values from a mined-out area of the Hartebeestfontein mine and accepting these as equivalent to borehole values (also areas of 1 km by 1 km as equivalent to 'mines'), the authors apply a series of borehole-valuation procedures to these 'mines', Large undeveloped sections of existing mines are also regarded as the equivalent of such 'mines'. These procedures start with the orthodox arithmetic mean and then introduce additional information in the form of the Iog normal frequency distribution model for Sichel's 't' estimator. Knowledge of the average log-variance within mines leads to the tH estimator. The mean grade of the 'family' of mines to which a new mine belongs is then introduced via regression or elementary kriging. Next, further information on the macro spatial structure of the grade is used, together with the grades of adjacent existing mines in ordinary and simple macro-kriging procedures; finally, via the distribution model, the grade is seen as a function of the logs of the grades and their variances. These are introduced as spatial variables, and both are estimated by macro-Iog normal ordinary and simple kriging procedures with grades and variances from adjacent mines'. Comparisons are also made between macro-kriging on lognormal transformed values versus untransformed values. Conclusions are drawn on the relative importance of the various items of additional information used, on the procedures followed, and on the significance of the advantages gained

Jan 1, 1992

By S. Budavari

The effects of shaft pillars left in deep-level hard-rock mines during the extraction of tabular deposits were studied some time ago, resulting in the formulation of design principles and procedures, which have been used with success in the design of shaft pillars in the deep-level gold mines of South Africa. The method has not yet been utilized in the design of shaft pillars in shallow and moderately deep hard-rock mines. The purpose of the present study was to remedy the situation since a great number of deposits are worked at those depths. The object of this paper is to present governing equations for the components of stress and differential movement as derived by use of an elastic model. The pillar is taken to be circular in the plane of a horizontal deposit. On the basis of the numerical results obtained, a study was made of the distribution of the vertical strain and tilt along the axis of the shaft, and of the vertical stress along the shaft and across the pillar. In every case investigated, the most adverse geometry was taken into consideration. By use of an empirical criterion and the results of some in situ observations, the determination of pillar dimensions and differential displacement components for South African gold-mining conditions is demonstrated. Pillar dimensions for shallow and moderate depths are compared with those accepted for deep-level conditions.

Jan 1, 1986

By L. C. Stilwell

The paper will place into perspective the contribution that platinum makes to the South African economy. It will use statistics from official sources, namely the Department of Minerals and Energy, the Department of Customs and Excise, the South African Reserve Bank and Statistics South Africa. Surprisingly few people are aware of these statistics, especially Supply and Usage tables, published by Statistics South Africa, and trade statistics, published by the Customs and Excise division of the South African Revenue Service. The paper will therefore contain a concise explanation of input-output tables and supply usage tables, as well as the derivation of gross domestic product and an outline of the System of National Accounts, of which Input-Output Tables and supply and usage tables are components. GDP is a commonly used, but poorly understood, measure of the wealth of an economy. The paper will explain the methods used by SSA to calculate this indicator and its place in the System of National Accounts (SNA). South Africa exports almost all its platinum production (87.5% in 2002). Exports are a final demand, as opposed to intermediate demand from secondary industries, and therefore do not enter the value-adding process, which is the essence of GDP. By definition, therefore, platinum on its own is not a major contributor to GDP. The platinum industry does, however, have an impact (known as the multiplier effect) on other sectors of the economy. The paper will explain the meaning and derivation of these multipliers, using a model based on an Inverse Leontief Matrix.

Jan 1, 2004

By D. F. Sinclair

It is often said in business that if you don't have a customer you don't have a business. The same rule applies to project evaluation; if you don't have customers you really don't have a viable project. It is therefore essential that in the early stages of project evaluation the following fundamental questions are addressed: ? What products will this project produce? ? Who are the potential customers? ? What are the customers' requirements with respect to grade and impurities? ? Do they have adequate capacity to take the production from the proposed project? ? Will the products introduce adverse effects in the customer's process circuits? ? Will additional waste streams requiring disposal be produced? In the past the attitude has been along the lines of the customer will take whatever we produce at the mine site. Times have now changed with customers now operating under much tighter environmental regulation with waste disposal becoming increasingly difficult. It would therefore be prudent that the principles of product stewardship be used as a tool in project evaluation. This paper will provide a general discussion on customer requirements and provide detail on case studies of the impact of mine products on smelter process circuits. It will provide examples where there were synergies between the mine product and the smelter circuit and where the mine product had adverse impacts on smelter performance.

Jan 1, 2007

By R. Yi

The determination of the optimum cutoff grade for a surface mine may be very different from that of an underground mine because a selectable mining method may be used in the latter case. A review of research into the theory of cutoff grade is made and then a new method, based on Optimal Control Theory, is presented. This method uses a Hamiltonian function to assist in obtaining the solution. It is shown that the life of a mine can be divided into three parts: a beginning period bf planning before mining; an intermediate period when both an average price and market information are used continually to adjust the cutoff grade; and, a final period when the main consideration is the current market situation.

Jan 1, 1987

By I. M. Macleod

An adaptive steady-state on-line optimizing regulator is proposed as an integrated approach to the control of autogenous run-of-mine milling circuits. This optimizing regulator continuously estimates an internal model of the controlled process, and, based on this, determines mill fresh solids feed rate, mill water flow rate and sump water addition flow rate such that a circuit performance objective is optimized. The dual -requirement of controlling both the mill pulp load and the load of particles of grinding media size is thus directly and simultaneously addressed. The concept and theory underlying the operation of the adaptive optimizing regulator are discussed.

Jan 1, 1987

By C. L. de Jongh

The number and scale of backfilling operations in the South African gold mining industry have grown rapidly in recent years. The application of backfilling as a means of stope support in a wide range of geological conditions and mining systems has resulted in the development of a variety of alternative fill systems. Experience gained in the evaluation of operating fill systems has contributed to a knowledge of the essential concepts to be considered in their design. This knowledge can also influence management's perception of what is expected of a backfilling system. The factors to be assessed in stating and satisfying these objectives are examined. The areas of investigation cover the selection of a suitable material, its preparation, distribution and placement, and the engineering logistics involved in the management of such a system. Finally, the integration of a filling system with an existing mining operation is examined.

Jan 1, 1988

By D. C. Andersen, G. L. Smith, A. M. Marsh, J. Pearson-Taylor

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2006

By N. Graham, C. Walker

The SORD Miner is a patented mining principle being developed to exploit mineral and energy resources that current technology can not access. SORD Miner is designed to operate in underground wet, granular, continuously collapsing geological environments such as alluvial and marine deposits. It is somewhat like a cutter suction dredge and should be capable of mining its way through any fine granular material like sand or gravel, pumping the slurry back to the surface. In areas where the target layer is covered, the SORD Miner is inserted below the water table and will tunnel its way to the mineral deposits at depth. This paper describes the development, concept testing and prototype construction of the SORD Miner.

Jan 1, 2007

Council and Standing Committees, 1977-1978 President: P. A. von Wielligh. Vice-Presidents: Dr M. G. Atmore and D. A. Viljoen. Honorary Treasurer: J. K. E. Douglas. Immediate Past President, Dr M. D. G. Salamon. Members of Council: J. D. Austin, A. N. Brown, A. A. Hazell, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, J. C. Mostert, H. G. M. Rose, W. T. Ruhmer, A. A. Sealey, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: A. N. Shand. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plowman, Dr R. E. Robinson, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, D. A. Vil¬joen; Technical Programme - Metallurgy, Dr P. R. Jochens ; Technical Programme - Mining, Dr D. K. Krige ; Vacation School - Metallurgy, Prof. R. P. King ; Vacation School - Mining, Dr M. D. G. Salamon; Awards, Dr M. D. G. Salamon; Excursions, Dr M. G. Atmore; Adjudication, Dr M. D. G. Salamon; Consti¬tution, Rules, and Policy, Dr M. D. G. Salamon; Mines and Works, P. A. von Wielligh ; Education, Dr M. D. G. Salamon; Monograph Series, Dr R. E. Robinson; Phoenix National Committee, Dr R. E. Robinson ; Pyrometallurgical Discussion Group Convenor, Dr J. B. See/Dr D. I. Ossin.

Jan 1, 1979

By M. L. Young, J. B. See

Effective thermal conductivities of packed beds of chromite ores by M. L. YOUNG, B.Se. (Rand), M.Sc. (Rand) (Visitor) and J. B. SEE, B.Sc. (Hons), Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) The effective thermal conductivities in stagnant air of packed beds of fines, lumps, and indurated and pre-reduced pellets of two chromite ores with different chromium-to-iron ratios were determined in the temperature range 300 to I 100°C by the heat-sink technique. Packed beds of fines, whether of the size fraction between 20 and 65 mesh, between 65 and 100 mesh, or between 100 and 150 mesh, were found to have the same values of effective thermal conductivity. For one ore, the effective thermal conductivities of packed beds of fines between 20 and 48 mesh at tem peratures above 600"C were higher than those for finer particles. This difference is explained as being due to the increase in importance of radiation heat transfer, but no definite conclusions are reached about the relative contributions of conduction and radiation heat transfer to the effective thermal conductivities of packed beds of fines between 20 and 48 mesh. Two published models were used for the theoretical prediction of values for thermal conductivities of the indurated and pre-reduced pellets as well as of lump ore. The experimental and theoretical results were in good agreement in view of the uncertainties in the assumed values of emissivity and thermal conductivity of the chromite ore.

Jan 12, 1976

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By L. Ozdemir, B. Asbury, T. G. Rozgonyi

A new type of bit, that has been developed and is being evaluated, shows great potential in expanding the range of rock strength that can be cut by continuous miners and roadheaders. This new style of bit is called the frustum. The tools tested in this program were developed, manufactured and patented by Briese Industrial Technologies, Inc. The frustum derives its name from the unique geometric shape of the cutter, or cutting insert. The frustum shape cutting tool has previously been proven as an effective cutting tool for machining metals, metal matrix composites and polymers. The frustum rock bit has a very dense carbide frustum shape tip mounted on the end of a steel body similar to the conical bits typically used on continuous miners and roadheaders. In between the carbide frustum cutting tip and the steel body there can be a bearing that allows the frustum to rotate around the bit axis. When the bit is forced into the rock at a skewed angle, the frustum tip rotates as it travels. This rotation greatly reduces the cutting forces acting on the bit when compared to the current state of the art conical drag bits. This cutting force reduction, derived from the frustum’s cutting action, allows for much harder and more abrasive rock to be cut without quickly wearing out the bit. Full scale laboratory cutting tests have been performed with the frustum bit in direct comparison to the current state of the art conical bits. Field trials of the frustum bit are currently being planned. Test procedures, results and findings are presented.

Sep 1, 2001

By P. J. Petit

The strategic mission of the South African mining industry is to extract the mineral assets in an energy efficient, economical and safe manner. Drilling has received particular attention in the last few years. As the operations move away from the power source, conventional and old drilling technology result in poor penetration rates, increased drilling shift lengths, slow face advances and limited stope efficiencies. The need for an alternate mining method, performed by a skilled workforce, to increase productivity, has led to the development of the electric rock drilling system for in-stope mining operations. The focus of this paper is a systematic evaluation of the electric rock drilling system as a function of production and technical parameters, in the platinum orebody. The particular electrical reticulation system is illustrated. Power usage, problems experienced, and solutions are described. The safe use of the recently developed drill is elaborated upon by describing protection devices. The testing and certification process, for approval by the recognized authorities, are documented. The testing and certification process, for approval by the recognized authorities, are documented. The human factor is also considered. Known detrimental factors of high noise exposure, vibrations levels and oil emissions are reviewed. In conclusion, recommendations on future strategies for the implementation of electric drilling technology within the mining and construction industries, is included.

Jan 1, 2006