Search Documents

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By R. Armstrong

Due to limited available level ground, Nkomati Nickel Mine cut a weathered rock slope at the base of a mountain spur in order to create a platform for construction of the primary crusher plant and run-of-mine stockpiles. As space is limited around the mining area, ore processing at Nkomati is based on a high reliability of flow of material through the crusher plant, with minimal usage of other and larger designed stockpiles. Evidently, any crusher plant shutdown will render the mine as a whole unproductive and put excessive strain on the medium- to long-term large ore stockpiles, the deposition rates for which are restricted by founding material consolidation requirements. At the onset of the 2012 rainy season, movement was identified on the slope monitoring system and cracks developed on the slope. After a minor failure on the crusher slope an assessment of the slope stability was conducted and a slope management plan recommended, which included deployment of real-time monitoring. An evaluation of the conditions leading to instability was conducted and the likely causes for the failure identified. A full evaluation of the slope monitoring, rainfall, and mining conditions was undertaken and movement triggers were determined. This paper describes the events leading to the development of the failure and the evaluation of the monitoring data to determine a management plan for the failure that allowed for minimal shutdowns of the primary crusher.

Jan 1, 2014

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

In constructing a financial model of a project significant effort is expended on capital and operating cost estimation, commodity price forecasts, and choice of discount rates while uncertainty in the primary input, the reserve, is often completely overlooked. The aim of this paper is to highlight the impact of uncertainty in the resource/reserve estimation process on the assessment of the financial performance of a project. Four qualitative processes have an impact on resource/reserve uncertainty. These stages are: 1.Ore definition 2.Geological interpretation 3.Resource estimation 4.Ore reserve estimation and mine planning. Each stage contains a number of tasks that may be considered as key performance activities (KPAs). Optimizing the manner in which these KPAs are completed can remove a great deal of uncertainty and error from the resource/reserve process. Examination of these KPAs within a company can also provide an insight to the quality of the information underlying the project. This will allow the company to identify any shortcomings in the data and to assess the resulting risks (Gilfillan, 1998). A hypothetical financial model based on a gold operation has been used to estimate the potential effect of resource/reserve uncertainty on revenue. Monte Carlo simulation has been employed to simulate a number of hypothetical scenarios: 1.a base case scenario which assumes no major errors or biases, but contains realistic margins for uncertainty that would exist in any project where work is being completed to the limit of best endeavours 2.a poor sampling scenario which assumes poor sampling practice and lack of understanding of sample preparation 3.a poor resource estimation scenario which assumes poor modelling and inappropriate choice of interpolation technique, and 4. a ?typical? scenario which represents a project where the majority of KPAs are not performed as best as they could be. The results show that realistic uncertainty ranges can generate changes in the estimate of potential revenue of plus or minus 30%.Therefore, it is important to allow for errors in these processes in any financial analysis or feasibility study. It is recommended that, when building a financial model, are view of relevant resource/reserve KPAs be carried out and appropriate ranges for uncertainty be applied to provide a range of potential outcomes. These outcomes can then be factored into the detailed cash flow analysis in order to ensure that technical uncertainty is built into financial decisions.

Jan 1, 1999

By H. J. Uananisa, M. J. Papo, C. W. Siyasiya, W. E. Stumpf

"SynopsisThe need to reduce weight while maintaining good mechanical properties in materials used in the automotive industry has over the years seen an increased exploitation of various steels to meet this new demand. In line with this development, the ferritic stainless steel family has seen a wide application in this industry, with the AISI 436 type increasingly being used for automotive trims and mufflers for exhaust systems, as well as a significant part of this steel’s application being for the manufacture of wheel nuts and wheel nut caps in trucks, mainly through the deep drawing process. However, there have been reports of some poor surface roughening of this material during deep drawing, with tearing and/or cracking also reported in some instances. This has been suspected to possibly be associated with some local differences in localized mechanical properties between grains and grain clusters of the rolled and annealed material.In order to investigate the poor surface roughness exhibited by AISI 436 ferritic stainless steel (FSS) during deep-drawing, Lankford values (R-mean and ?r), grain size, and microtextures of various sheet samples from this steel were studied. The chemical composition range for the samples was 0.013–0.017% C, 17–17.4% Cr, 0.9–1% Mo, and 0.4–0.5% Nb. The steels were subjected to various hot and cold rolling processing routes i.e. involving industrial direct rolling (DR) or intermediate annealing rolling (IR), and the drawability and final surface qualities of the steels were compared. It was found that the DR route gave an average R-mean and ?r value of 1.9 and -1.4 respectively, while the IR route yielded an average Rmean and ?r value of 1.6 and 0.52 respectively. The high ?r value for the DR processing route had a substantial adverse effect on the drawability. IR samples exhibited a smoother surface finish on visual inspection, while clear flow lines were visible on the DR samples, despite the fact that DR is the preferred industrial processing route due to the reduced production costs it offers. This observation was also confirmed through SEM examinations. The difference in the surface quality was attributed to microtexture. However, the mechanism responsible for this difference still needs to be identified."

Jan 1, 2015

By J. P. W. Bennie, A. de Jong, G. M. Denton

Mintek together with Middelburg Steel & Alloys, developed the DC arc furnace process for the production of ferroalloys with the expressed objective of smelting ore fines (<1mm) without the need for agglomeration. In the case of ferrochrome production, the DC arc furnace, being a semi-open bath operation, loses radiant energy directly from the bath to the furnace roof and sidewalls above the melt. This energy loss is reflected in a higher electrical energy usage per ton of alloy than for a submerged-arc operation smelting lumpy ores or sintered pellets. The difference increases still further when pre-heated sintered pellet feed is used in a submerged-arc operation. This shortcoming of the DC arc furnace can however be overcome by preheating the feed to the furnace in a fluidized bed or flash reactor fuelled by cold furnace off-gas. In addition to fluidization and preheating testwork, various preheating flowsheets with associated mass and energy balances have been developed and compared from a techno-economic viewpoint. The three major advantages identified were: a) fluidized beds can preheat ores and fluxes up to 950°C without sticking and defluidizing, b) the open bath DC arc furnace does not require expensive coke or char to maintain the burden porosity and, c) the capital cost associated with the milling, pelletising and sintering plant falls away since ore fines are used directly.

Jan 1, 2004

By A. V. Peake

Continuous Mining presents an opportunity to extract reef in the stope ?continuously? by integrating the drill and blast activity using propellants or low energy charges. To date, the majority of effort spent on Continuous Mining systems has focused on developing an effective rock breaking process (micro breaking process), and to some extent, eliminating fumes and dust. The perceived benefits of applying low energy charges have been identified as: ?Concentrated mining yielding face advances of 40 to 60 m per month ?Lower stoping widths through better-controlled breaking ?Increase in the advance per blast ?Increase in labour productivity ?The potential to mine reefs where specific conditions make conventional mining uneconomic e.g. reefs with shales in the immediate hangingwall. However, the ability to successfully use low energy charges to create a ?Continuous or Semi-Continuous? mining method is dependent on overcoming the following challenges. ?Improving reliability of rock breaking. This is dependent upon achieving:? Improved drilling accuracy, and? Successful stemming or gas confinement, particularly in fractured rock ?Reducing gas and dust levels ?Reducing high costs. Through the research carried out in Future Mine, many different low energy rock breaking methods and systems were investigated. Whilst detailed results cannot be published here, the guidelines for overcoming low energy rock breaking challenges are discussed.

Jan 1, 2003

This paper provides a review of the chemical reactions occurring in the submerged arc processing of chromite ores. The excavations of industrial furnaces have shown that the charge, as it descends through the furnace, passes through a number of distinct reaction zones. Each zone is characterised by differing process conditions and reaction products. The phase equilibria, reaction steps and mechanisms occurring as the charge progresses through the furnace are examined, and the potential influences of these factors on the process outcomes are discussed.

Jan 1, 2004

By A. Feather

The Minataur? Process (Mintek Alternative Technology for Au Refining) is a novel route for the production of high-purity gold using solvent extraction. Following the successful demonstration of the process on a pilot-plant scale, a full-scale 24 t/a production plant has been commissioned at Harmony Gold Mine in Virginia, Free State. The commercial implementation of this process represents not only a significant advance in gold-refining technology, but may be instrumental in initiating important changes in the legislation regulating the marketing of gold in South Africa. Gold of either 99.99% or 99.999% purity can be produced from intermediate process products having a wide range of gold contents. The process comprises oxidative leaching of the solid feed, followed by selective solvent extraction of the gold from the leach liquor to reject impurities, and precipitation of high-purity gold powder. This paper outlines the process, presents selected results of two pilot-plant trials in which 5 kg/d of high-purity gold was produced from silver-refining anode slime and gold-electrowinning cathode sludge, and provides some details of the cost benefits.

Jan 1, 1997

By M. F. Handley

Sequential grid mining has been employed as the primary mining strategy at the AngloGold West Wits Elandsrand Mine since the inception of stoping operations from the sub-vertical shaft system in 1988. Little has been published on sequential grid mining as a mining strategy since, and the purpose of this paper is to describe sequential grid mining, its history, its implementation at Elandsrand, and the outcome to date. The results obtained using sequential grid mining have been evaluated from seismic data, productivity statistics, and rock related accident statistics. Comparisons with neighbouring mines namely Western Deep Levels and Deelkraal, have been made to substantiate the improved conditions observed at Elandsrand, and to compare sequential grid mining directly with longwall mining in similar conditions and at similar depths. Sequential grid mMining is shown to be cost-effective, more flexible, and safer than long wall mining in similar conditions, at least on the Ventersdorp Contact Reef in the western part of the Carletonville Goldfield. More work is necessary to establish it as the favoured mining strategy at depths exceeding 3000 metres, and for reefs other than the Ventersdorp Contact Reef.

Jan 1, 2000

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013

By W. P. Roux

Owing to decreasing high-grade ore reserves, there is a need for better understanding of the jigging process to improve the recovery efficiency of finer, lower grade material. The use of positron emission particle tracking (PEPT) was examined as a technique to study the motion of iron ore particles inside a laboratory batch jig. PEPT is a non-invasive method that can provide three-dimensional kinetic data on a particle in laboratory-scale processing units and has been successfully used to study mills, hydrocyclones, and flotation. Experiments were conducted to determine whether PEPT would be a viable technique to study iron ore jigging and what valuable information could be obtained. The results indicated that detailed information on the stratification rate of a particle could be obtained, with adequate resolution to track the particle?s movement through an individual jig pulse.

Jan 1, 2014

By TvS. von Moltke

Steel is a highly versatile material due to its low cost and good mechanical properties, but typically needs some or other form of corrosion protection due to its tendency to corrode when exposed to atmospheric conditions. In the case of organic coatings, the corrosion protection and functionality of the final product is critically dependent on the adhesion of the coating to the surface of the steel. In this work the effect of contaminants and the nature of the surface layers present on industrial steel products are investigated by means of paint adhesion tests, Auger electron spectroscopy (AES), and X-ray Photoelectron spectroscopy (XPS). It was found that the presence of sodium species on the surface is very detrimental to paint adhesion under wet conditions, while satisfactory adhesion may be obtained even in the presence of silicon and carbon residues. It was also found that the nature of the Fe-O layer, formed under wet conditions is labile and different from that formed in dry air, and that subtle changes in process conditions, such as changing the oxygen content of the quench water, may change the adhesion of paint to the surface of the steel. Lewis acid-base interactions are discussed as a mechanism that may determine the bonding between the steel and polymer coating.

Jan 1, 2003

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours&apos; exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours&apos; exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By B. W. J. van Rensburg, M. J. Schmidt

Bulk materials handling systems are extensively used in the mining and minerals industry, where a fairly high incidence of structural failure is experienced, notwithstanding design compliance with appropriate standards. A number of case studies are explored to demonstrate how insufficient controls or protection systems have contributed to structural failures on mobile bulk handling equipment. The importance of design integration across engineering disciplines is highlighted. The revision of ISO 5049-1 (1994) is proposed to provide specific rules and guidelines pertaining to machine protection systems. It is further recommended that the structural design engineer of the original equipment manufacturer(OEM) fulfils a more prominent role during the final acceptance and handover of mobile bulk handling equipment, with specific reference to protection systems.

Jan 1, 2015

By F. T. Cawood

?It is in the interest of stability and investor confidence that the healthy and necessary debate on such a (minerals) policy should soon find its way to consensus.? (President Nelson Mandela at the104th (1995), AGM of the South African Chamber of Mines) Inauguration of the new political dispensation in South Africa initiated a dynamic period in the historical development of its minerals policy. The process of substituting the current South African mineral policy framework with an acceptable ?post apartheid? system, started soon after the 1994 election of the African National Congress (ANC) government. The Green Paper on a Minerals and Mining Policy for South Africa released for public discussion in February 1998, calls for radical transformation in mineral rights ownership. A shift towards exclusive state ownership of mineral rights, away from the present dual system of private and state ownership, is the most significant proposal. The current holders of mineral rights, or their nominees, who lawfully enjoyed security of tenure under past and present mineral laws are opposed to this transformation because mineral rights were often acquired at considerable cost. The situation is compounded by poor public record-keeping and passive mineral rights administration over a very long period. This paper represents a summary of the historical developments leading to the current legislative environment and forms the basis for any discussion on which future sculpturing of South Africa?s policy regarding mineral rights can take place. One cannot plan for the future without considering the past!

Jan 1, 1998