Search Documents

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By D. R. Young

Drilling exploration over the Wesizwe Platinum Limited?s Pilanesberg Project has identified the Merensky Reef at depths varying from 594 m to 1 552 m depth. Merensky Reef thickness varies from 0.05 m to 3.63 m and contains PGE(4) mineralization above a cut-off grade of 1.0 g/t over intersection widths of 0.95 m to 2.63 m. Four distinct facies types have been identified over the property, viz.1) Normal Merensky Reef, generally 1.2 m thick, bounded by thin top and basal chromitite layers and composed of upper feldspathic pyroxenite and lower feldspathic olivine pegmatoids containing base metal sulphide mineralization overlying poikilitic anorthosites. 2) Single chromitite Merensky Reef, generally0.15 m thick and usually devoid of internal silicate material, overlying variable stratigraphy containing significant base metal sulphide mineralization. 3) Detached Merensky Reef, generally1.0 m thick, bounded by thin top and basal chromitite layers and composed of feldspathic pyroxenite or pyroxenite containing base metal sulphide mineralization overlying Merensky Pyroxenite. 4) Normal footwall Merensky Reef, generally 1.8 m thick, bounded by thin top and basal chromitite layers and composed of feldspathic pyroxenite containing base metal sulphide mineralization overlying norites also containing significant base metal sulphide mineralization. The PGE(4) content?s (g/m2) distribution for the global intersection data appears to be lognormal, and conversion to lognormal space produces a near normal distribution which could be interpreted as a compound lognormal distribution. The mean PGE(4) contents estimated by these three different distributions are the same, and thus do not impact on the contained metal. Data for the Normal Merensky Reef facies type are sufficient to indicate that a normal distribution is followed for this facies type, and therefore does not need to be transformed to log space for estimation of the mean and the 90% confidence limits. A global evaluation based on all of the data is compared with a facies-weighted evaluation. The latter method is noted to provide a better definition of the associated estimation errors and thus potential classification of Mineral Resources. A valuation of $20.95 for Inferred and $41.90 for Indicated PGE(4) ounces is applied to both of the evaluations and compared. The global evaluation is considered to over-value the project by approximately 40%, thus indicating that valuations based on global summary sampling data that have a compound distribution may be materially flawed, and that cognizance of the underlying geology is crucial for unbiased valuation.

Jan 1, 2006

By H. H. McGregor

Introductory remarks by author When Mr R. C. J. Goode suggested preparation of a paper in the area of manpower utilization in South Africa, I was, while keen to accept his invitation, somewhat hesitant for two reasons. Firstly, I recognized the great difficulty of making a factual contribution, because of the lack of really relevant statistical information available, the fact that much of it is out of date, and the difficulty of researching and co-ordinating it and of evaluating a statistically sound resultant viewpoint. Experience in the actual preparation of this paper has done nothing to change my view in this respect. Secondly, it is obvious that a paper presented to a meeting of this Institute, by a member of it, would be expected to devote considerable attention to the subject in the mining industry. I am not directly employed by the mining industry, although my company has carried out extensive assignments for various sectors of it both in this country and in other parts of the world, since the 1939-45 war. I am more conscious than most of the tremendous technical and managerial skills at the disposal of the industry in this country, and consequently am equally conscious of the hazards of publishing facts and figures which might be taken to indicate any criticism of performance. I am aware that some of the information that I am about to present may indeed generate comment, and possibly even critical comment. I would like to be regarded therefore in presenting this information, as a member of the group, rather than an external critic. Under these circumstances, comment can only be constructive, and this is my earnest hope. The contribution of my paper, if contribution there is, will I hope be in the area of assessing labour productivity in mining, and in secondary industry in such a way that the performance of each against its own past results is comparable. This task has not for the present been to my knowledge attempted, and in advance I wish to take out authors' insurance against legitimate criticism from professional economists and others, by stating that I am well aware of possible short-comings in the arguments. Nevertheless I believe that under the circumstances I have, with the important assistance of several people, been able to take the subject further than has been the case in the past. Finally, I have related productivity in the mining industry and in secondary industry to a target of productivity in the Republic of South Africa. I was fortunate recently in being able to attend a series of lectures by a prominent economist in America. He introduced his subject by calling it 'A broad survey of macro-economics'. Perhaps I might be permitted to describe my paper, in the same idiom, as 'The macro-management of labour'.

Jan 6, 1970

By H. Gercek, M. Genis

In this paper, the effects of dynamic loads on the geometry of the failure zone occurring around underground openings, excavated in deep and massive rock masses, have been investigated. Following an elasto-plastic stress analysis of a two-dimensional underground opening under static conditions, dynamic loads have been applied. In the static and dynamic analyses, FLAC2D computer program has been utilized. Maximum ground acceleration value is selected as an input parameter. An index determining the relative size of the yield zone around the opening has been used for comparison of instabilities. In diesem Bericht wurden die Auswirkungen von dynamischen Lasten, auf die Geometrie der Bruchzone in der Umgebung von Untertagehohlräumen, die in tiefen und massiven Gebirge aufgefahren wurden, untersucht. Nach einer elasto-plastischen Spannungsanalyse eines zwei-dimensionalen Untertagehohlraumes unter statischen Beanspruchungen, wurden dynamische Lasten aufgebracht. Für die statischen und dynamischen Analysen wurde das FLAC2D Computer Programm verwendet. Die maximale Bodenbeschleunigung wurde als Eingabe Parameter gewählt. Zum Vergleichen der Unstabilitäten wurde ein Index verwendet, der die relative Grösse der Bruchzone in der Umgebung des Hohlraumes bestimmt. Dans ce papier, l’influence des chargements dynamique sur la géométrie de la zone en rupture observée autour des cavités profondes excavées dans des massifs rocheux ont été étudiées. Des chargements dynamiques ont été appliqués, dans le cas d’une modélisation bi-dimensionnelle de l’excavation d’une cavité profonde, sur la base d’une analyse élastoplastiques des contraintes en conditions statiques. Le code de calcul FLAC2D a été utilisé pour les analyses statiques et dynamiques. La valeur maximale de l’accélération du sol est choisie comme paramètre d’entrée. Un indice déterminant la taille relative de la zone sollicitée autour de la cavité a été utilisé pour comparer les différentes instabilités.

Jan 1, 2003

By P. Gonzalez

Minera La Parreña, S.A. de C.V., Milpillas operation is an underground mine designed to process 8 352 tons of ore per day for the recovery of copper through crushing, heap leaching, solvent extraction and electrowinning facilities. In order to optimize copper recovery during leaching, the ore is crushed to 13 mm and subjected to primary sampling every 15 minutes for metallurgical accounting. At the same particle size, primary sample goes to secondary sampling and then, the secondary sample is crushed to 2 mm before tertiary sampling. The tertiary sample is sent to laboratory where a final sample is obtained and pulverized to 106 microns for copper assay. This paper shows a review of sampling strategy focused on minimizing or eliminating sampling errors and an experiment designed to determine copper head grade profile as well as the best sampling frequency.

Jan 1, 2009

By D. Moradkhani, S. M. Javad Koleini, M. Abdollahy, F. Soltani

"The objective of the study was to determine the type and distribution of rare earth elements (REEs) in the phosphate flotation concentrate from the Esfordi flotation plant in central Iran, in order to understand their leaching behaviour. Samples of the concentrate were prepared and analysed using XRF, XRD, ICP, and EMPA. The Ce, Nd, La, and Y contents were 5608, 2227, 1959, and 679.7 mg/kg, respectively. The main REEbearing minerals in the concentrate are fluorapatite, monazite, and xenotime. Apatite is the chief mineral of the concentrate and the ratio of apatite to monazite is greater than 60. From EMPA analysis, monazite contains a much higher proportion of REEs than apatite, but more than 50% of the REE content of the concentrate is in apatite, as this is the main mineral constituent of the concentrate. During the leaching of REEs in the phosphoric acid production process, more than 99% of the total rare earth values report to the large amounts of phosphogypsum (CaSO4·2H2O) formed during the dissolution reaction. Accordingly, two process options are suggested for treating the Esfordi concentrate. In the first option, the concentrate is treated with 98% H2SO4 at 200–300°C. After digestion and water leaching, phosphorus and REEs are precipitated out of solution. In the second option, the concentrate is treated in a pre-leach stage. The process residue from the pre-leach stage is then subjected to acid digestion at elevated temperature for phosphoric acid production.IntroductionThe rare earth elements (REEs) comprise a set of 17 chemical elements in the periodic table, specifically the 15 lanthanides plus scandium and yttrium. REEs and alloys that contain them are used in devices such as computer memory, rechargeable batteries, cell phones, catalytic converters, magnets, fluorescent lighting, and many more (Krishnamurthy and Gupta, 2004). China supplies about 94% of the REE demand, with the remaining 6% coming from Russia and Estonia, the USA, India, Malaysia, and Brazil (Zhanheng, 2011). Increased industrial development in China has prompted the Chinese government to limit annual export quotas to approximately 35 kt of rare earth oxides (REOs), while non-Chinese annual demand is expected to reach 80 kt by the year 2015. This constriction of supply is being met by the development of many new rare earth mining projects, each of which has its own unique mining and processing challenges (Jordens, Cheng, and Waters, 2013). One of these projects is the Esfordi phosphate project, which is located in Yazd Province in central Iran. The concentrate from the Esfordi flotation plant contains 1.2–1.5% REEs."

Jan 1, 2017

By T. Moyo

"The oxidative leaching of chalcopyrite in ammoniacal solutions has been evaluated using electro-analytical techniques and controlled bulk leaching studies. The anodic dissolution process has been established to be a sevenelectron transfer process under nitrogen in ammonia–ammonium sulphate solutions and ammonia–ammonium carbonate solutions, which suggests that the sulphur is oxidized to thiosulphate and the copper and iron released as Cu+ and Fe2+ in these systems. The deportment of Fe2+ and S2O3 2- is affected by choice of the ammonium salt used in the leaching process. In the perchlorate salt, only five electrons are transferred, supporting formation of different sulphur species as proposed for the sulphate and carbonate salts. Scanning electron microscopy and energydispersive spectroscopic analysis of the mineral surface after leaching indicate presence of an iron–sulphur surface layer completely free of copper in the sulphate system, an iron-rich surface layer in the perchlorate solutions, and absence of surface layer build-up in carbonate solutions. XRD analysis of a bulk leach residue from leaching in ammoniaammonium sulphate solutions showed the surface layer to be mostly amorphous (90%). The crystalline content (10%) is composed of 95% polymorphs of anhydrous iron oxide hydroxide FeO(OH). Choice of ammonium salt and the hydrodynamic environment of leaching have been shown to influence the presence or absence of the surface product, as well as its nature. IntroductionHydrometallurgical processes for copper extraction provide a viable route to recover the metal from mixed and low-grade ores, as well as overcome the environmental challenges faced by the traditional pyrometallurgical processes. Chalcopyrite is not only the most abundant of the copper sulphides, but also the most stable, making it recalcitrant to hydrometallurgical processes. Hence, hydrometallurgical processing of chalcopyrite continues to be an attractive area of research due to the vaguely understood surface chemistry of the mineral in different aqueous media. Different routes for hydrometallurgical treatment of chalcopyrite can be followed. These include thermal treatment prior to leaching, direct leaching and direct electrochemical leaching (Venkatachalam, 1991). Direct leaching of chalcopyrite can be carried out in various solution systems, as reviewed by Roman and Benner (1973) and Venkatachalam (1991). Ammoniacal solutions are attractive and effective lixiviants that form stable amine complexes with some base metal cations while rejecting iron. Leaching of chalcopyrite in ammoniacal solutions in the presence of an oxidant is possible due to the stabilization of copper (I) and copper(II) by ammonia at elevated pH levels. In oxygenated ammonia solutions, it has been suggested that chalcopyrite dissolves according to Equation [1] (Beckstead and Miller., 1977a):"

Jan 1, 2016

By P. Altounyan, K. Akermann, T. Van den Berg

Amandelbult Mine is currently undertaking a trial to mechanise the mining of the UG2 reef through the introduction of room and pillar mining. As part of the trial, a system of managing the control of the hanging wall has been introduced, based on systems and technology that are proving successful in the nearby coal mining industry. The principal features are the use of a high bond strength, stiff bolting system which can be easily installed to a high standard, and a range of in situ tests and measurements to optimise the level of support installed to control the movement of the hanging wall. The rock bolt system and the measurements and tests described are new to the platinum mining industry. The paper describes these systems and their adaptation and application to hard rock mining. La Mine d’Amandelbult est actuellement dans des essais en vue de mécaniser l’extraction dans la veine UG2 grâce à l’introduction d’une exploitation par chambres et piliers. Dans le cadre de ces essais, un système de gestion de la paroi suspendue a été introduit, base sur des systèmes et une technologie qui prouvent donner de bons résultats dans l’industrie voisine d’extraction de la houille. Les caractéristiques principales sont l’utilisation d’un système de verrouillage raide et à forte adhérence qui peut être installé à un haut niveau de qualité et une gamme d’essais et de mesures in situ pour optimiser le niveau de soutien installé pour contrôler le mouvement de la paroi suspendue. Le système de verrouillage de la roche ainsi que les mesures et les essais décrits sont une nouveauté dans l’industrie minière du platine. La communication décrit ces systèmes ainsi que leur adaptation et leur application à l’exploitation minière en roche dure. Amandelbult Mine unternimmt gegenwärtig einen Test um den Abbau des UG2 Riffs durchEinführung des Kammerpfeilbau zu mechanisieren. Als Teil dieses Tests wurde ein System zur Kontrolle der Stollenfirstes eingeführt, welches auf jenen Systemen und Technologien basiert, diesich im nahe gelegenen Kohlebergbau als erfolgreich erwiesen. Die prinzipiellen Charakteristikasind der Gebrauch von einem steifen Bolzensytem mit hohem Verbundwiderstand die leicht zueinem hohen Standard gebracht werden können, und eine Reihe von in-situ Tests und Messungenum das Niveau der installierten Unterstützung zu optimieren, und um die Bewegung desStollenfirstes zu kontrollieren. Das Gesteinsbolzensystem, die Messungen und die Tests, diebeschrieben werden, sind neu in der Platinbergbauindustrie. Diese Arbeit beschreibt diese Systeme, deren Anpassung und Anwendung im Hartgesteinsbergbau.

Jan 1, 2003

By C. W. Siyasiya

Process and steel chemistry differences in hot rolled Al-killed low carbon strip steel between the hot charge route (HCR) as practised in a compact strip production (CSP) plant and the conventional cold charge route (CCR) have been studied. This was done with reference to differences in reheating practice, hot rolling practice and steel chemistry through emphasis on the effects of solubility and reprecipitation of AlN in the two process/product combinations and its effect on ferrite grain size development. An earlier modelling study on the evolution of the austenite grain size in both of the above hot rolling processes has also now been extended to include an estimate of the possible effects of retained strain after the last finishing pass on the ferrite grain size. As part of this study the equilibrium solubility trends of AlN in a number of boron-free low carbon Al-killed strip steels with low and high sulphur content from the two respective processes was investigated by the thermoelectric power (TEP) technique and differences in the effects through the derived solubility equation of Log[Al][N]=2.6?9710/T at typical slab reheating temperatures was demonstrated. Ferrite grain size modelling using the significantly lower Ar3 transformation temperatures generally found in hot rolled low carbon strip steel produced in the CSP plant using the HCR compared well to the larger grain size produced in the conventional CCR strip rolling plant. Keywords: austenite grain size modelling; thermoelectric power(TEP); compact strip production (CSP); cold charge route (CCR);ferrite grain size

Jan 1, 2008

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009

By G. R. J. Cooper

In recent years attempts have been made to develop software packages for shallow seismic refraction data analysis. In most cases, mainframe computers were used which were generally non-interactive, did not support graphics and were unfriendly to operate. With these facts in mind, a user-friendly interactive processing package written in PASCAL has been developed for the IBM PC. The package allows the following operations to be performed. (1) data tying, equalisation of reciprocal and common shot times; (2) overburden velocity analysis; (3) refraction leg identification on time-distance plots; (4) elevation correction of refractor data; (5) forward and backward phantoming; refraction leg extrapolation; (6) 'bedrock' velocity analysis; (7) 'time-depth' plot computation; (8) depth calculation. Numbers (6) - (8) above involve Palmer's generalised reciprocal technique of refraction data interpretation. The program is extremely flexible and makes much use of interactive high resolution graphics and 'popup' onscreen menus. The velocity analysis sections have statistical routines built in to provide error estimation. The programs allow data interpretation to take place in the field with a portable microcomputer while the data are still being collected; this is obviously not possible with any cumbersome mainframe-based software. Hence it becomes possible to see the effects of varying the data collection parameters (such as geophone spacing) upon the resulting interpretation and so enable adjustments to be made where necessary. Hard copies of the data may be obtained at all stages of the interpretation process using a small (A3) plotter, or the graphics may be dumped to a dot- matrix printer if a suitable plotter is not available.

Jan 1, 1987

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By E. Keskinkilic

Drying, calcination, prereduction, and smelting are the main steps in conventional crude ferronickel production. Industrially, these steps are conducted using the rotary kiln-electric arc furnace (RKEF) process. In this paper, calcination characteristics of Sivrihisar laterite ores from the Central Anatolia region are investigated. The extent of elimination of chemically bound water and other volatiles was studied by experiments conducted at various temperatures in the 250?800°C range. Phase changes were examined using X-ray diffractometry. For the particle size used in the study, 300°C was determined to be almost sufficient for complete transformation of goethite to haematite, and 700°C was required for effective elimination of all volatiles in the ore.

Jan 1, 2012

By A. Muller

The magnesia-carbon refractories used in the ConArc process experience severe wear as a result of the varying slag composition during the blowing phase. This work determines the basicity range in which minimum as well as maximum refractory wear was experienced by the magnesia-carbon refractories during service. In order to determine an optimum slag composition, the crucible test in an induction furnace was used. The magnesia-carbon refractory bricks were cut into cylindrical crucibles to which a synthetic slag in the form of pellets was added. The basicity (B2) of the slag was varied from 0.5 to 3. Tests were done at 1 600°C for one hour. Apart from the crucible test in an induction furnace, visual inspection and SEM analysis were also done to investigate the corrosion mechanism. FACTSage® predictions about the interaction between refractories and slag were also done. These predictions were compared to the actual results attained. It was found that the extent of corrosion by slag attack decreases as the basicity increases. The most severe corrosion of the MgO-C refractories occurred at a basicity of 0.5 whereas the optimum basicity is above 2.0. SEM analysis indicated severe slag attack at the lower basicities with no visible refractory-slag interaction at higher basicities. TheFACTSage® predictions supported most of the actual findings. Keywords Magnesia-carbon, ConArc, blowing phase, slag resistance, induction furnace, crucibles.

Jan 1, 2011

By D. Yu Pleev, V. G. Krivolapov

Mines of Southern Kuzbass working out, basically, coal formations of flat seams. Seams, as a rule, are inclined to self-ignition. Detection at early stages of the centers of endogenous underground fires has great value for safe conducting mountain works. One of methods of detection of an early stage of underground fires in the worked out space is the method of superficial radon survey. In the report the method is de-scribed and examples of superficial radon survey on concrete layers are given.

Jan 1, 2003

By L. H. Lindstad

The paper reviews the tapping process and the major wear mechanisms on the tap-hole, including wear from tapping tools. Measured temperatures in different tap-holes are related to choice of binder and material for repair pastes. The strength and disadvantage of carbon and silicon carbide materials are compared. Normal daily and weekly maintenance of tapholes is described, together with the major repairs that are done during longer furnace shutdowns. The objective is to show that the type of repair and repair material needs to be adapted to each individual furnace.

Jan 1, 2014

By F. S. Beretta

Mineral processing efficiency depends on various factors and among them includes head grade fluctuations feeding the processing plant. Head grades can fluctuate beyond an admissible range, implying in recovery decrease for the mineral of interest. Grades feeding the processing plant depend on the geological domain which is being mined and on the mining schedule. Therefore, it is necessary to keep grade variability controlled. Blending piles are an efficient alternative to reduce grade fluctuations. The main factors influencing blending efficiency are the pile size or its mass and the number of layers used to pile up. Large piles are more efficient to reduce variability, however, there are economical and operational limits associated with them. This study investigates a methodology to analyse the ideal pile size to reach an acceptable variability given the in situ grade fluctuations. Geostatistical simulations provide the means to assess grade variability using an optimized mining schedule. These block grades are used to simulate any given pile throughout the mine`s life. The methodology was illustrated using a case study to control coal ash content at a mine supplying ROM coal to a power plant. Keywords: homogenization, piles, geostatistical simulation.

Jan 1, 2009

By E. Lwamba

The aim of this study was to examine the effect of grain size distribution control of the raw material mixture on the permeability of the green sinter bed and the properties of the produced sinter. This was achieved by evaluating the granulation characteristics of the sinter mixture (moisture content, granulation time and mean granule diameter) in terms of its green bed permeability, and evaluating the productivity of the sinter bed, the coke rate, tumble index (TI), abrasion index (AI), reduction disintegration index(RDI) and reducibility (RI) of the produced sinter. The raw sinter mixtures contained combinations of Thabazimbi iron ore, Sishen iron ore, coke, lime and return fines. The grain size distributions were controlled by removing the ?0.5 mm size fractions of the return fines and coke, and the ?1 mm size fraction of lime. Of the examined mixtures, a mixture of 20 mass% Thabazimbi iron ore, 80 mass% Sishen iron ore and fluxes where the coke, lime and return fines were all sized had the highest granulation effectiveness and permeability. The sintering properties of the mixtures in which the grain size distributions were controlled, were very similar for all the mixtures, but superior to the base case mixture in which the grain size distribution was not controlled. Keywords: Thabazimbi iron ore; Sishen iron ore; granulation, permeability, grain size distribution; sinter.

Jan 1, 2008