Search Documents

By B. McFadzean, S. Pikinini, C. T. O’ Connor

Sperrylite (PtAs₂) comprises about 21% of the platinum group minerals (PGMs) in the Platreef ore and regularly reports to the tailings due to its poor floatability. Hence, improving its recovery will be of great economic value to the South African PGM industry. The reasons for its poor floatability are not yet clear. This paper seeks to understand the interactions occurring between PtAs₂ and common thiol collectors, viz. potassium normal butyl xanthate (PNBX), sodium normal dibutyl dithiophosphate (SNBDTP) and sodium normal mono butyl dithiocarbamate (SNBDTC). By understanding its interactions with these collectors, it is hypothesised that it will be possible to suggest ligands that may help improve the floatability of sperrylite. Mineral-collector interactions were studied by determining the molar energy of interaction using isothermal titration calorimetry and electrochemical techniques. The hydrophobicity of the mineral before and after adsorption of the collectors was determined by heat of immersion and its flotation response determined by microflotation tests. Microflotation tests using synthetic sperrylite at pH 9 showed low collectorless recovery of 34.8% and after adding the equivalent of one pseudo-monolayer of the PNBX collector, the recovery of 32.5% was obtained. Moreover, the addition of up to three pseudo-monolayers coverage of PNBX did not result in any increase in flotation recovery. A small recovery improvement was noted when synthetic plant water with the ionic strength of 0.0484 mol/L was used, but this did not hold for all collectors, with SNBDTP exhibiting higher recoveries in distilled water. Keywords: Sperrylite; flotation; recovery; adsorption energy; collectors; 2SPW (synthetic plant water)

Jan 1, 2020

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

1. Book review Respiratory protection - principles and applications by B. Ballantyne and P. H. Schwa be (Editors). London, Chapman Hall, 1981. (Reviewer: M. J. Martinson) 2. New manual Swedish steel manual, 1981. Available from Jernkontoret, P.O. Box 1721, S-I11 87 Stockholm, Sweden. SEK 85. 3. Publications of the Mineral Policy and Energy Sectors, Canada General review by L. Tibbo. 10 pp. Columbium (niobium) and tantalum by D. G. Fong. 6 pp. Sulphur by B. W. Boyd. 13 pp. Statistical summary of the mineral industry in Canada. 66 tables. Uranium by R. M. Williams. 16 pp. 4. Mintek reports Report 2126 The determination, by microwave techniques, of the interface between pulp and froth. Report 2129 An electrode controller for submerged-arc furnaces. Report 2131 The separation of trace elements in manganese dioxide. Report 2132 The assessment of pellicular anion-exchange resins for the determination of anions by ion chromatography. Report M2 The preparation of two reference materials of South African fluorspar. Report M3 The platinum-group minerals in the UG-2 Layer of the Bushveld Complex at Maandagshoek 254KT.

Jan 1, 1982

By E. Shavartz, N. B. Strydom

The incorporation of individual cooling in a compressed-oxygen closed-circuit breathing apparatus by E. SHVARTZ, M.Sc. (U.C.L.A.), Ph.D. (U.S.C.) (Visitor) and N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow) A conventional compressed-oxygen breathing apparatus, which did not include provisions for dehumidification of the inspired air at high environmental temperatures, was tested at these temperatures with and without conductive cooling in the form of 2 kg of pre-frozen ice placed inside the breathing bag of the apparatus. The pre-frozen ice provided conductive cooling of the soda lime and of the chest and abdomen of the subject, who performed moderate work at 50,1 "c. Without cooling, the subject was exhausted after 35 minutes because of a wet-bulb temperature of the inspired air of 46"c. With cooling, the subject finished 2 hours of work. This was possible by keeping the soda lime at a relatively Iow temperature, which resulted in a wet-bulb temperature of the inspired air of only 42 °C after 2 hours, and by conductive cooling of the chest, which resulted in the maintenance of a relatively Iow heart rate and rectal temperature.

Jan 7, 1975

The annual General Meeting of the Branch was held in the St. Helena Club on Wednesday, 4th August, 1971 at 8.00 p.m. Mr N. A. Honnet (Immediate Past Chairman) was in the chair. There were also present Mr V. C. Robinson, President of the South African Institute of Mining and Metallurgy. Nine Fellows: Messrs J. R. F. Handley, C. J. Isaac, J. Lorenzon, J. M. Meyer, C. Mostert, D. A. Smith, S. L. S. Swart, I Thomas and R. G. Williams. Five members: Messrs R. Campbell, A. H. Edwards, K. Pearce, G. P. Rundle and R. B. Sutherland. Five graduates: Messrs J. E. Andrews, E. J. Shillaber, M. H. Smith, T. R. Stromsoe and D. J. van Niekerk. Two associates: Messrs A. Paschalides and D. S. Robinson. Eight visitors. Total present: Thirty-one. MINUTES OF THE PREVIOUS GENERAL MEETING As the minutes of the General Meeting held on the 16th June, 1971, had not been published in the Journal, the Chairman moved that the adoption and discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. The minutes of the General Meeting held on the 10th February, 1971, were taken as read. The adoption, which was proposed by Mr D. A. Smith and seconded by Mr J. M. Meyer, was carried unanimously. At Mr Honnet's request, Mr V. C. Robinson took the chair during the presentation of the Chairman's Annual Report. CHAIRMAN'S ANNUAL REPORT 1970/71 1970/71 Committee-Office Bearers: Chairman - J. N. Saunders Vice Chairman - G. Y. Nisbet Immediate Past Chairman- N. A. Honnet. Due to the sudden retirement of Mr J. N. Saunders, the committee, at a meeting on the 3rd February, 1971 elected Mr G. Y. Nisbet as Chairman with Mr J. M. Meyer as Vice Chairman. After the transfer of Mr Nisbet to C.D.M., the committee, as a meeting on the 12th May, 1971, decided that Mr Meyer hold the Chair in an acting capacity for the remainder of the year. Committee members: Messrs C. J. Isaac, J. G. Kirchener, L. O. W. Leimer, R. S. Pearson, I. G. Thomas and A. von Holdt. Transfers of several office bearers and committee members resulted in Messrs J. M. Meyer, D. N. Smith and G. C. J. Young being co-opted onto the committee.

H. W. Glen (ed.). Proceedings of Asbestos Symposium, Johannesburg, South, Africa, 3rd-7th, October, 1977. Randburg, National Institute for Metallurgy, 1978. 158 pp. (Copies obtainable from the Department of Mines, P.O. Box 4584, Johannesburg, 2000 South Africa.) This Symposium, which concentrated on the theme of dose-response relationships for asbestos-related diseases, was attended by an internationally representative group of experts in this field. Bulk solids The Powder Advisory Centre announces its third annual International Conference on Bulk Solids Swrage, Handling and Flow, to be held at the Holiday Inn, Liverpool, on 7th to 9th November, 1978. This sequel to the extremely successful November '76 Stratford and November '77 Nottingham Conferences is again to be co-sponsored by a number of internationally acknowledged professional societies, including the Institute of Materials Handling (through its Bulk Solids Panel), the Institution of Production Engineers, and the American Society of Mechanical Engineers (through its Materials Handling Engineering Division). NIM reports Report no. 1943 A review of the literature on the separation and determination of rare-earth elements. (23rd Mar., 1978.) Report no. 1947 The cation- and anion-exchange behaviour of various base-metal chlorides in polar organic solvents. (lOth Mar., 1978.) Report no. 1948 The measurement of trace amounts of gold in solution by atomic-absorption spectrophotometry and carbon-rod atomization. (28th Feb., 1978.) Report no. 1949 The kinetics of the leaching of zinc sulphide concentrates in acidic solutions containing ferric sulphate. (23rd Mar., 1978.) Report no. 1950 Factors affecting the carbon contents of alloys formed during the prereduction of chromite ores. (31st Mar., 1978.) Report no. 1952 The effect of slag composition on copper losses to silicasaturated iron silicate slags. (31st Mar., 1978.) Report no. 1953 A fundamental investigation into the depression of copper-activated sphalerite. (28th Apr., 1978.) Report no. 1956 An improved ion-exchange separation of rare-earth elements for spectrographic analysis. (10th Mar., 1978.) Report no. 1960 The recovery of ferrochromium from furnace slags and related products. (20th Aug., 1976; declassified 31st Mar., 1978.) Process instrumentation The National Institute for Metallurgy and the South African Institute of Measurement and Control are organizing a symposium that will draw the attention of researchers and industrial workers to the importance of metallurgical process instrumentation.

Jan 1, 1978

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

By N. Mangadoddy, M. Padhi

The simulation of multi-component classification with modified viscosity model is the key focus in the current study. The classification of the ores using hydrocyclone is a renowned process and has a convoluted flow separation phenomenon. The highly turbulent flow inside hydrocyclone depends on the operating and design parameters apart from the feed mixture. Slurry viscosity also plays a dominant role in the classification of solid particles under the centrifugal settling action. A heterogeneous mixture with different components would result in different settling and rheological behaviour of particles’ suspension in the water medium. The newly proposed multi-component viscosity model (Mandakini et al. 2020) is implemented as a user-defined function to define the material property during the CFD study of the mixture rheology inside hydrocyclone classifier. The multiphase and turbulence model is solved using the modified Algebraic Slip Model and Large Eddy Simulation model. A comparison of the predicted component performance curves is evaluated with and without the corrected viscosity model. The density and size effect on the particle phase distribution inside the classifier are compared, where the misplacements of the finer particles are carefully assessed. Validation of the component classification in hydrocyclone with the laboratory experiments found a close agreement with the rheology based CFD data. Keywords: Dual-component, multi-component viscosity model, double-gap rheometer, computational fluid dynamics, high solids concentration

Jan 1, 2020

By P. Harris, N. Heywood

An existing 1 800 m long pipeline, which carried waste mica slurry from kaolin processing, is to be recommissioned. The mica solids throughput is to be substantially increased from 5.2 t/h up to a maximum of9.53 t/h, but with a typical throughput of around 7.5 t/h. Because of this throughput increase, it was unclear whether the existing 80 mm diameter pipe would be adequate. In addition, the pipe route is to be extended by 250 m to 2 050m, and its elevation at discharge to settling lagoons increased from 66.2 m to 80 m. The pipeline hydraulics of waste mica slurry were investigated for the 80 mm diameter pipe using the Saskatchewan Research Council?s (SRC) Two-Layer Flow Model, for the maximum mica solids throughput of 9.53t/h. The pipe operating velocity was compared with the predicted deposit velocity for several mica concentrations, ranging from 20% to 50% by weight. Estimates were made of the total differential pressure across the proposed2 050 m long pipeline, as well as the power imparted to the slurry by the pump, and the specific energy consumption (SEC). Two pipe diameters were assumed: 80 mm when no mica wall deposit is present, and 70 mm when there is a 5mm mica wall deposit. This parameter has a significant effect on the determination of the appropriate pipe operating conditions. For the pipe operating velocity to remain adequately above the deposit velocity (and therefore for the heterogeneous flow pattern to prevail in either horizontal or inclined pipe), it was concluded that if the newly commissioned pipeline contains no mica wall deposit, the pipe should initially be operated at a mica concentration of between 20% and 25% by weight, probably with a target mica concentration of about 23%. A 23% mica

Jan 1, 2007

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

The problem of providing adequate thrust to manually operated rockdrills operating at air pressures of 70 lb/in2g to 80 lb/in2g with the aid of an air-leg is analyzed. It is shown that adequate thrust is provided by an air-leg or the stiff-leg if it is inclined at an angle to the floor of about 25°. However, this requires that the leg react against some support or protuberance, as the friction force between the leg and the floor is inadequate to contain the thrust. Conclusions summarizing optimum thrusts, blow frequencies, penetration rates, drill steel life and bit wear are presented.

By M. Akyüzlü

The equilibrium between carbon-saturated Fe-Cr-Si-C alloys and SiO2-CaO-MgO-A2O3-CrO2-FeOy slags was studied under atmospheres of argon and carbon monoxide at temperatures of 1500 and 1600°C. The equilibrium distribution of chromium, silicon, and iron between the slag and the metal phases was determined for different compositions of both phases under different atmospheres and temperatures. It is shown that silicon transfer from the slag to the metal increases with increasing temperature, decreasing carbon monoxide partial pressure, decreasing carbon content of the metal, increasing chromium-to-iron ratio of the metal, increasing silica content of the slag, and decreasing lime-to-alumina ratio of the slag. Some activity calculations were made for the experiments conducted at 1600OC in a carbon monoxide atmosphere. It is also shown that a decrease in the iron content and an increase in the slag basicity decrease the chromium content of the slag. A major proportion of the chromium present in the slag was found to be in the divalent state under the highly reducing conditions prevailing in the experiments. The chromous capacities of these slags were calculated and were found to decrease with increasing basicity.

Jan 1, 1992

1. Books from Elsevier The folowing are available from Elsevier Applied Science, Crown House, Linton Road, Barking, Essex IGl 8JO, OK. . Driling wastes, edited by F.R. Engelhardt, J.P. Ray, and A.H. Gilam. 1989. 872 pp. £95. Geothermal resources, by R. Bowen. 2nd ed. 1989. 468 pp. £60. The fate and efects of oil in freshwater, edited by J. Green and M.W. Tret. 1989. 340 pp. £42. Mining and the freshwater environment, by Martyn Kely (with contributions by W.J. Alison, A.R. Garman, and C.J. Symon). 1988. 228 pp. £32. 2. Books produced by Metal Buletin The folowing are available from Metal Buletin PLC, Park House, Park Terace, Worcester Park, Surey KT47HY, England. Prices and data 1990. £41 (airmail). Foundry directory and register of forges 1989-1990. £52 (airmail). 2. Canadian Publications The folowing two publications are available from the Canadian Government Publishing Centre, Supply and Services Canada, Otawa, Canada KIA 059. Mining and mineral processing operations in Canada. Mineral Buletin MR 224. $23.70. Canadian minerals yearbook 1989. Review and outlook. Mineral Report 38. $47.95. Technology developments The Mintek Pyrosim Simulator Pyrosim is a computer program for the steady-state simulation of pyrometalurgical processes?.

Jan 1, 1990

ERRATA-AUTHOR'S REPLY IN SEPTEMBER, 1970, JOURNAL: PAGE 52 I. Left half of the page, 4th paragraph, fifth line from the bottom: for 22 / 5 1/2 %, read 22 / 5 1/2 %. 2. Right half of the page, fifth paragraph from the bottom, third line from the bottom: for N(l - p), read N(1 - p)x. 3. Right half of the page, fourth paragraph from the bottom, second line: for: at time t after time zero, read: at time x after time zero. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

By S. Wakita, K. Aoki, Y. Mito, K. Date

It is of great importance to prevent a leakage of hazardous substances from underground storage plants, because this certainly leads to a fatal disaster for human societies. Therefore, effective grouting system needs to be developed, which can inject cement grout into low-permeable rock masses. Authors have carried out a series of laboratory injection tests using a fracture model and field tests in low-permeable rock masses. In these tests, not only was the superiority of dynamic grouting confirmed, but also the relationship between grouting-efficiency and injection parameters was investigated. In this paper, the results of laboratory injection tests and field tests together with theoretical approaches to them are mentioned. L’empêchement de la fuite des substances dangereuses des galeries de stockage est un traitement très important pour protéger la société humaine contre la comtamination catastrophique. Par conséquent, un procédé d’injection efficace doit être mis au point, qui peut injecter du coulis de ciment dans le rocher ayant une perméabilité basse. Les auteurs ont effectué une série d'essais d'injection en laboratoire en utilisant un modèle de rupture et d'essais sur le terrain dans le rocher ayant une perméabilité basse. Dans ces essais, était non seulement la supériorité du l’injection dynamique confirmée, mais aussi le rapport entre l’efficacité de l’injection et les paramètres d'injection a été étudié. Dans cet article, les résultats des essais d'injection en laboratoire et des essais sur le terrain ainsi que les méthodes théoriques pour les essais sont mentionnés. Es ist wichtig, Durchsickerns gefährlicher Substanzen aus unterirdischen Lagerstellen zu verhindern, weil dies für die menschliche Gesellschaft unter Umständen zu verheerenden Unfällen führen kann. Daher muß ein effizientes VerfugesSystem entwickelt werden, welches erlaubt den Mörtelschlamm in wenig durchlässige Felsenmassen einzuspritzen. Die Autoren haben eine Serie von Laboreinspritzungsversuchen mit einem Bruchmodell und Feldversuche an wenig durchlässigen Felsenmassen durchgeführt. Diese Versuche zeigten nicht nur die Überlegenheit des dynamischen Verfugens, sondern wurde dabei auch das Verhältnis zwischen Verfugen und Leistungsfähigkeit sowie den Einspritzungparametern untersucht. In dieser Studie werden die Ergebnisse der Laboreinspritzungtests und die Feldversuche zusammen mit den entsprechenden theoretischen Ansätzen erläutert.

Jan 1, 2003

The following contributions were received to the paper entitled 'Safety in South African mines: An analysis of accident statistics', by H.S. Eisner and J.P. Leger, which appeared in the J. S. Afr. Inst. Min. Metal., vol. 88, no. 1, Jan. 1988, pp. 1-7. Contribution by H. WAGNER* The paper by Dr H.S. Eisner and Mr J.P. Leger is critical of the safety situation on South African mines and portrays the industry as having little concern for the health and safety of its workers. Moreover, the casual reader gains the impression of deliberate misinformation by the industry to the public concerning safety maters. Furthermore, certain socio-economic reasons are advanced for the apparent differences between the fatality and injury rates reported for coal mines in South Africa and those for the United Kingdom. Contribution by S.A. WATTS. Authors Eisner and Leger are to be commended on their paper, which highlights, according to their interpretation, various shortcomings of both the Chamber of Mines accident statistics and those published by the Department of Mineral and Energy Affairs. Authors' Reply We gratefully acknowledge Dr Wagner's contribution to the discussion on our paper. For convenience, we shal use his sequence of comments in our reply. Before doing so, however, it may be useful to explain how our paper came to be written. After the explosion at Hlobane Colliery in 1983, one of us (HSE), in February 1984, was retained by the lawyers acting for some of the dependants of the victims to advise on technical maters relating to the explosion. Contribution by Ms S.A. Wats Some of the points made by Ms Wats have already been answered in our comments on Dr Wagner's contribution. We are fully aware that the number of accidents leading to absences of less than 4 days would be much greater than shown in our bar chart, and are grateful to Ms Wats for drawing attention to the specific exceptions that can make a 1-3 day accident compensable and that are clearly responsible for the relatively low count in that category of the chart.

Jan 1, 1988

By E. Spicer

X-Ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems in XRD creates the opportunity to use this technique in modern process control. In the analysis of heavy mineral sands, XRD can identify the main mineral phases, such as ilmenite FeTiO3, rutile TiO2, Zircon ZrSiO4and quartz SiO2, and any other minor components present, such as anatase TiO2, magnetite Fe3O4, haematite Fe2O3or monazite (Ce, REE)PO4. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis (Bish and Howard, 1988) are attractive alternatives, as they do not require any standards or monitors. These methods offer impressive accuracy and speed of analysis. The Rietveld method compares calculated versus experimentally derived X-ray powder diffraction patterns for the sum of all crystalline phases. Another analysis technique offering great benefit to mining industries is cluster analysis. Enormous amounts of XRD measurement data are generated during the process control and material evaluation. New ways of handling such vast amounts of data are required to produce meaningful information for the end users. Cluster analysis greatly simplifies the analysis of a large amount of data from different processes or different raw materials, and automatically sorts closely related scans of an experiment into clusters and marks the most representative scan of each cluster as well as outlying patterns. The use of cluster analysis to evaluate the XRD data allows fast and reliable tracking of the process. It is the most economical procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimization methodologies, results, data precision and limitations will be discussed. The approach has potential as a relatively inexpensive, reliable tool, useful in the characterization of heavy minerals sand materials.

Jan 1, 2007

1. Recent books D. K. Hsiao, D. S. Kerr, and S. E. Madnick. Computer security. New York, Academic Press, 1979.276 pp. $18. W. C. J. van Rensburg and S. Bambrick. Economics of the world's mineral industries. Isando, McGrawHill, 1979. R18,95. Soviet metallurgical research 1973-1977. Vo!. 1. Subject index and author index (1963-1972). Vo!. 2. Chronological listing of titles with full bibliographical information (1960-1972). London, Scientific Information Consultants Limited (661 Finchley Road, London NW2 2HN). £24 per set. W. Hoosen. Miners' dictionary. London, Institution of Mining and Metallurgy, 1979. (Reprint.) £11 (£9 for members). G. J. Pitt and G. R. Millward. Coal and modern coalprocessing: an introduction. New York, Academic Press, 1979. 224 pp. $18. D. Stephenson. Rockfill in hydraulic engineering. Amsterdam, Elsevier, 1979. 228 pp. U.S. $45, D.fl.90. 2. NIM reports Report no. 2015 The preparation of synthetic standards for use in instrumental neutron-activation analysis. Report no. 2029 The commissioning of a 5 kW inductively coupled plasma unit for use with a 3,4-metre Ebert spectrograph. Report no. 2032 The Cancer Project: a summary of the computer-aided operation of a 48 MV.A ferrochromium furnace. Report no. 2036 The determination of thallium in ores, concentrates, and metals. Report no. 2040 A solid-state constant-current power unit for the magnetic analyser of the MS702R mass spectrometer. Report no. 2044 The separation and determination of anions by ion chromatography. Computer congress In October 1980, Japan and Australia are hosting the 8th World Computer Congress. This Congress is a triennial event conducted under the sponsorship of the International Federation for Information Processing. INFACON 80 The Second International Ferro-Alloys Congress, organized by IPFEO (Institute of Western European Ferro-alloy Producers), is to be held in Lausanne, Switzerland, on 13th to 16th October, 1980.

Jan 1, 1980

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003