Search Documents

By S. M. H. Haddad, M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

Sulfide impurities in iron ore concentrates play an important role in designing pelletising and steel making plants. Therefore attempts are made to keep the sulfur content of the final concentrate produced by the plants as low as possible. Generally, in the beneficiation process of iron ore concentrate, the removal of sulfur is performed through magnetic separation systems, followed by reverse flotation. The sulfide content of the iron ore concentrates originated from two main sources, including pyrite and pyrrhotite. In this research, in order to compare the floating capability of these two types of sulfide minerals, two iron ore concentrates with different sulfide constituents, pyrite or pyrrhotite, were selected. Reverse flotation tests were done separately on these samples under similar conditions. Process parameters considered for the tests included pH (2, 4, 6, 8 and 10), collector consumption (150, 200, 250, 300 and 350 g/t) and frother consumption (40, 50, 60, 70 and 80 g/t). Potassium Amyl Xanthate (PAX) and Methyl Isobutyl Carbinol (MIBC) were the collector and frother used in the tests, respectively. For modelling and optimising process parameters, the Central Composite Design (CCD) method was applied to the test results. Empirical coded equations were obtained for responses involving weight recovery, Fe recovery, Fe grade and S grade. Finally, comparison of test results revealed that the elimination recovery of pyrite sulfides was far greater than pyrrhotite sulfides, and it was possible to remove 84% sulfur content of the pyrite sample compared to minus 30% for the pyrrhotite sample. Keywords: Reverse flotation, pyrite and pyrrhotite, sulfur removal, iron ore concentrate, beneficiation plant

Jan 1, 2020

By J. W. van der Merwe, A. M. Maleka, V. J. Matjeke

The 10.5–12.5% chromium, titanium-stabilized ferritic stainless steel (FSS) plates used to fabricate coal line jumbo wagons is susceptible to undesirable chromium depletion during welding with 309L electrodes. In this work, non-stabilized FSS plates were welded using 308L welding electrodes. The objective was to weld non-stabilized FSSs using gas-shielded metal arc welding without causing sensitization. The welding process was optimized by lowering the heat input. Sensitization was assessed by rigorous etching techniques and anodic polarization scans. In addition, the welds were subjected to tensile testing, and their fracture surfaces were examined for intergranular cracking. Non-stabilized FSS plates were successfully welded using gas metal arc welding.

Apr 5, 2023

By F. Dinter, S. A. C. Hockaday, Q. G. Reynolds

The thermal decomposition of carbonate minerals as pre-treatment before smelting reduces the energy requirement for smelting. It can also make the combustion of fossil fuels for heating unnecassary. Thermal decomposition may become important in reducing greenhouse gas emissions when producing ferromanganese alloys while simultaneously reducing electrical energy demand during smelting. A kinetic reaction rate model for the thermal decomposition of manganese ores is presented, based on published reaction rate kinetics for the decomposition of manganese oxides and calcium carbonate. The model was validated against thermogravimetric data for two carbonaceous manganese ore samples and one ferruginous manganese ore sample. The reaction rate model shows that carbonate minerals in the manganese ores are decomposed at temperatures above 900 °C while pyrolusite is decomposed at temperatures from 450 °C to 500 °C. Mn2O3 decomposes rapidly at 550 °C. Braunite decomposition at temperatures below 1000 °C was negligible. The presence of organic carbon in the samples led to further reduction of the samples during thermal treatment.

Aug 3, 2023

By G. B. Abaka-Wood, J. Addai-Mensah, W. Skinner

Recently, coal fly ash has become a potential candidate as a secondary resource of rare earth elements (REE). In this investigation, we studied the recovery of REE from fly ash from a commercial power plant. The specific aim was to assess the technical feasibility of recovering REE from the coal fly ash using conventional preconcentration methods, including gravity separation, magnetic separation, and froth flotation. The experimental results revealed that flotation achieved major gains in REE recovery and upgrading. However, during gravity and wet magnetic separation tests, the bulk of REE reported to the tailings. The results showed significant variations in the performance of the various beneficiation methods investigated. This study has confirmed that existing physical separation methods could be used to recover REE from coal fly ash prior to hydrometallurgical and pyrometallurgical processing, although some challenges persist.

Jan 2, 2022

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

By M. E. Rossi, C. Badenhorst

Conditional bias occurs when the expected value of the true grade conditional on the estimated grade is not equal to the estimated grade. It is a quantification of how the average of estimates differs from the true value. Conditional bias is present in all resource estimates due to the unavoidable properties of kriging, and indeed all linear estimation (regression) methods. In a mining resource estimation context, the degree of conditional bias is dependent on the spacing of the conditioning data; more data leads to the expectation of less conditional bias This paper discusses conditional bias from two perspectives: 1. 2. Estimates seeking to eliminate, as much as possible, conditional bias; and Estimates that accept a larger amount of conditional bias in resource models, in order to achieve a specific outcome. The problem of conditional bias in estimation can only be fully appreciated if the objective or purpose of a resource model is understood. There are instances where conditional bias should be avoided because it is not reasonable to make decisions using estimates that are known to be wrong in expected value; for example, when making a final decision in grade control with respect to the destination of the material. In most instances in the mining resource estimation context, however, the estimated values will not be “final estimates”, but “interim estimates”, meaning that in the future more data will be obtained, and the ”interim estimate” will then be updated. In this context, the most useful resource model is an interim model that is able to predict the final model estimates, despite not having all the data available that will be collected in the future. This is the objective, for example, of a recoverable “long-term” model developed prior to operating a mine, for example at the feasibility stage. It attempts to predict the ore that a processing plant will receive, well into the future. In such cases, it can be unequivocally demonstrated that conditional bias is not only unavoidable, it is a necessity.

Sep 1, 2021

By S. Saeed, N. Coulson, P. F. Stewart

"The Mine, Health and Safety Act No. 29 of 1996, as amended, embodies worker self-regulation to advance health and safety in the workplace. An important provision for this is the Right to Refuse Dangerous Work (RRDW). This paper explores worker perspectives about the implementation of RRDW on South African mines against a backdrop of revised guidance in the sector: ‘Guideline for a Mandatory Code of Practice on the Right to Refuse Dangerous Work And Leave Dangerous Working Places’, gazetted in February 2016 by the Department of Mineral Resources (DMR). A mixed methods study conducted at mines (n = 14) included a survey of workers (n = 293), focus groups (n = 6) and in-depth interviews (n = 16). Workers reported a high level of awareness, a positive attitude, and experience of the formal RRDW. However constraints to the formal RRDW meant that informal worker resistance to dangerous work was commonplace. Evidence of informal non-confrontational consultation, cooperation, and collaboration in the event of a dangerous workplace also emerged between workers, and supervisors. The research underscores the importance of the RRDW and worker health and safety representatives to mine health and safety. The revised guidance addresses RRDW implementation gaps, but of concern is the potential partiality towards management interests. IntroductionEnsuring that mineworkers act on their duties and responsibilities for health and safety remains a concern across the globe. Article 13 of the International Labour Organization (ILO) Convention Safety and Health in Mines (176 of 1995) entrenched the Right to Refuse Dangerous Work (RRDW) as an important mechanism through which workers act in the best interests of their own occupational health and safety (OHS) and is considered a cornerstone of worker self-regulation (ILO, 1995). Countries ratifying Convention 176 are under obligation to make this right available to workers through OHS legislation that frames the circumstances, procedure, and protection of workers from discrimination in the event of a formal work refusal. The Convention has been ratified by 31 countries, with South Africa becoming a signatory in June 2000 (ILO, 2000). Worldwide studies show that workers use this right with caution (Hilgert, 2013) and cases associated with work refusal are rarely presented in court (Gunningham, 2007; Cooper, 2013). Rather, in cases of formal notification of a work refusal, issues arising out of this are addressed either in the immediate workplace or through the site OHS system and/or at industrial tribunals or similar mechanisms (Harcourt and Harcourt, 2000)."

Jan 1, 2018

By E. R. Leeman

INTRODUCTION The first references in the literature to the so-called C.S.I.R. 'doorstopper' strain cell were made in 1964 1,2,3,4. These were the climax of nearly two years of experimental and developmental work with the instruments and the operating techniques involved. Since that time numerous field measurements have been made with 'doorstoppers' and they have been developed to a stage where they are in commercial production and are being supplied to users throughout the world. No detailed description of the latest 'doorstopper' equipment has, however, appeared in print and this paper is written to bring the literature up to date in this respect. The triaxial strain cell was developed three years ago 5, 6, 7 and was first described at the First Congress of the International Society for Rock Mechanics in Lisbon in 1966 8. Since that date laboratory tests and-particularly important-field tests 7' 9 have demonstrated the validity and practicality of the instruments and techniques. These instruments have also been developed to a stage where they have been released for commercial production. In this form they are very different from those described two years ago and a full description of them at this stage seems to be justified. THE INFORMATION SUPPLIED BY 'DOORSTOPPER' AND TRIAXIAL STRAIN CELLS Both the 'doorstopper' and triaxial strain cells were designed specifically to determine the absolute stress in rock using an overcoring stress relieving technique. They were not designed to measure changes in stress. They may, however, be used for the latter purpose provided the glue which is used to stick the strain gauges to the rock is known to possess sufficiently stable strain-time characteristics as not to affect the accuracy of the results during the time the measurements are made. The 'doorstopper' was designed primarily to measure the major principal stress in situations where its direction and those of the two other principal stresses were either known or could be assumed. For example, at great depth in undisturbed virgin ground, it is reasonable to assume that the maximum principal stress is vertical and that the other two lie in a horizontal plane. The borehole in which the 'doorstopper' is installed would thus be drilled in the horizontal plane parallel to one of the minor principal stresses, the direction of which would either have to be assumed or determined as described later. The stresses measured would be the vertical major principal stress and the principal stress acting in a horizontal plane normal to the borehole axis. It is possible, as will be shown later, to obtained the complete state of stress using 'doorstoppers'. In this event, it is necessary to make measurements in three boreholes drilled in any three known directions to each other and relative to a system of three orthogonal axes. The triaxial strain cell was designed to determine the complete state of stress in a single borehole drilled in any direction in any stress field. At first glance it would appear to supersede the 'doorstopper'. This is not necessarily true since there are

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By Wei Sun, Ruolin Wang, Wenjuan Sun, Junhao Fu, Haisheng Han, Zhao Wei

Pb–benzohydroxamic acid (BHA) (lead complexes of benzohydroxamic acid) exhibits high selectivity but low collecting efficiency in scheelite flotation. This paper reports the manner in which BHA and sodium dodecyl sulfate (SDS) were employed as ligands to coordinate with the lead ions to obtain a colloidal lead-group multiple ligand complex, i.e., the Pb–BHA–SDS, for improving the collecting efficiency of Pb–BHA. The flotation mechanism of Pb–BHA–SDS with respect to scheelite was investigated from the viewpoint of interface science based on the pure mineral flotation, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and contact angle measurements. The results showed that the BHA and SDS coordinated with Pb2+ to form novel leadgroup multiple ligand complexes, which are different from the traditional understanding associated with the mixed collectors. Pb–BHA–SDS was a better collector with stronger collecting ability and excellent selectivity in regard to a scheelite flotation than Pb–BHA. The addition of SDS to Pb–BHA enhanced the latter’s adsorption ability on the scheelite surface and improved the hydrophobicity of the collector’s nonpolar groups, rendering Pb–BHA–SDS as a more efficient collector at a low dosage. Keywords: Scheelite; Pb-BHA complexes; sodium dodecyl sulfate; multiple ligands; Pb–BHA–SDS

Jan 1, 2020

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By M. Ericsson

?Rare earths ?will not be bargaining instruments?? was stated in a headline in China Daily of 29 October 2010. The Chinese government is trying to fend off the persistent accusations from Japan, the USA, and Europe that it is manipulating the supply of these so called ?critical? metals to gain political and economic advantages. The critics maintain that China has taken the rest of the world hostage by controlling 97% of the resources of rare earths. These elements are crucial in a number of high-tech applications. They are not impossible to substitute, but difficult to do so effectively. The name ?rare earth? is a misnomer, as even the least abundant is 200 times more common in the Earth?s crust than gold. They are, however, difficult to find in economic concentrations. The Chinese near-monopoly over the rare earths, together with China?s scramble for other resources in Australia, Africa, and elsewhere around the world, is seen as an example of a Chinese strategy to take control of vital metal resources. The Chinese are also accused of using unfair and sometimes illegal business practices in this fight for resources. Practices which, critics claim, put the Chinese interests above the interests of the host countries, in particular in Africa.

Jan 1, 2011

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By G. Akdogan, J. H. Zietsman, C. Dorfling, D. Attah-Kyei

The development of newer and improved electrical products has led to an increase in the rate at which older products are discarded as waste. The main focus of electronic waste is the printed circuit board (PCB) because of the inherently high value of contained metals such as gold and copper. Several options for treatment of the non-metallic fraction including material recycling, where the residue may be used as inclusions in concrete or asphalt materials with minimal processing or chemical recycling, where chemicals and fuels are produced from the residue using pyrolysis exist. In this paper, the utilisation of the non-metallic leached PCB waste fraction as reductant in secondary copper smelting was investigated. Analysis of the leached residue revealed that PCB is highly amorphous and has a carbon content of 28.5%, an oxygen content of 23.1%, with the ash and volatile matter contents 40.1% and 44.8% respectively. Thermodynamic simulations of secondary smelting of copper were conducted in terms of metal recovery, and the energy required when PCB was used as a reductant. The results were also compared with that of coal and PCB-coal blends. The simulations revealed that as PCB in the blend used as reductants increases, the amount of energy required for the smelting operation decreases. Metal recovery slightly decreased as the mass percent of PCB in the blend increased due to lower carbon content present in PCB relative to coal. The results also highlighted the energy saving with PCB-coal blends which was around 160 kWh per ton of feed relative to coal. The decrease in the amount of energy required for the operation is attributed to the higher volatile content of the PCB, which is also a part of the reduction process. Keywords: PCB leach residue, alternative reducing agent, secondary copper smelting

Jan 1, 2020

By V. Jokovic

Hydrocyclones are the most commonly used classifiers in the mining industry. The reason for this is their low operating cost and a small footprint. Data from plant trials where screens replaced hydrocyclones indicated that lower bypass of fines and sharper separation could improve breakage rates, with a positive effect on flotation circuit performance throughput. Despite the importance of classification, hydrocyclones have not received as much attention as more expensive comminution units, and their technological progress has been incremental. Noticeable water split (Rf) reductions of a semi-inverted hydrocyclone have been reported in the past. According to theory, the hydrocyclone with reduced Rf will improve classification of fines. A classification study using semi-inverted hydrocyclones was conducted to determine if a hydrocyclone could be operated in a way that would minimise misclassified fines. The classification performance of a semi-inverted hydrocyclone will be presented in this paper and other potential applications will be discussed. Keywords: Semi-inverted hydrocyclone, water split, misclassification of fines

Jan 1, 2020

By M. Pawlik, N. Ghaffari Touran

The interactions between apatite and hematite were studied through zeta potential and stability experiments, for this paper. The zeta potential measurements were conducted in both background electrolyte and mineral supernatants. The difference in electrokinetic properties of minerals in the presence and absence of supernatant was explained in terms of the dissolution of minerals and the subsequent readsorption of dissolved species at the mineral-water interface. The stability measurements in individual and mixed mineral systems were also performed to identify the extent of interaction between apatite and hematite upon their direct contact. The results from stability measurements in individual and mixed mineral systems indicate that there is an interaction between apatite and hematite. Based on the results, the implications for the apatite-hematite separation process were discussed. Keywords: Apatite, hematite, dissolved ions, stability, zeta potential

Jan 1, 2020

By K. Sasaki, S. Kuroiwa, H. Miki, Y. Aoki, T. Hirajima, Y. Orii, G. P. W. Suyantara

Selective flotation to separate copper minerals from, for example, Mo- and/or As-bearing minerals is a continuing problem because the selectivity of current systems is imperfect. Selective Cu-As flotation is currently difficult, and the most common Cu-Mo selective flotation method uses NaHS; this must be done in an enclosed system because, under acidic conditions, this method produces hydrogen sulfide. In this paper, some novel alternative flotation processes that use redox reactions are discussed; these methods have a much lower environmental impact. Oxidation and reduction reactions can be used to make copper minerals more hydrophilic and Mo-bearing minerals more hydrophobic. X-ray photoelectron spectroscopy (XPS) analyses indicated that the copper minerals became hydrophilic because hydrophilic iron precipitated and several hydroxides covered the copper minerals’ surfaces, whereas the molybdenum minerals remained hydrophobic because their sulfide surfaces were not covered. Flotation experiments on these minerals after redox treatments indicated that excellent separation of Cu-minerals from Mo-minerals can be achieved. Possible mechanisms for this separation were investigated using detailed surface analyses and thermodynamic calculations. The additives used to initiate the redox reactions are easy to handle and make these new flotation procedures better than current processes because the new methods do not emit effluent gas and because they are commercially viable. Keywords: Flotation; chalcopyrite; molybdenite; oxidation; reduction

Jan 1, 2020

By W. Bendaikha, S. Larbi, A. Ramdane

An oolitic iron ore from Gara Djebilet, Algeria was characterized by X-ray diffraction, scanning electron microscopy, and energy dispersive spectrosopy and the phosphorus distribution between various phases studied. Two ore types were identified – a haematite-dominated, oolitic type and a more massive, magnetite-dominated type. The haematite-dominated ore had a higher phosphorus content, up to 0.6% in the iron oxide minerals, than the magnetite-dominated type (0.3% P). Owing to the very fine-grained texture of the gangue minerals, reducing the phosphorus content to levels suitable for steelmaking (below 0.05% P) by conventiobal means would entail an energyintensive process with a high carbon footprint. Preliminary leaching test work using a sulphurous geothermal water as lixiviant, assisted by solar thermal acceleration, gave very promising results, removing 0.13% of the residual P (or 21.7% removal of total P) from the high-phosphorus oolitic ore.

Mar 14, 2024

By D. Paktunc, S. P. du Preez, J. P. Beukes, P. G. van Zyl, A. Jordaan

"The chromium (Cr) content of stainless steel originates from recycled scrap and/or ferrochrome (FeCr), which is produced mainly by the carbothermic reduction of chromite ore. The oxidative sintered pellet production process is one of the most widely applied FeCr processes. The supplier of this technology specifies that recycling of chromite-containing dust collected from the pellet sintering off-gas and fines screened out from the sintered pellets (collectively referred to as pre-oxidized chromite fines) should be limited to a maximum of 4 wt% of the total pellet composition. However, the results presented in this paper suggest that recycling of such fines up to a limit of 32 wt% of the total pellet composition may improve the compressive and abrasion strengths of the cured pellet. In addition, electron microprobe and quantitative X-ray diffraction (XRD) analyses demonstrate that chromite grains present in the pre-oxidized chromite fines consist, at least partially, of crystalline phases/compounds that will improve the metallurgical efficiency and specific electricity consumption (i.e. MWh/ton FeCr produced) of the smelting process. Introduction Stainless steel is a vital modern-day alloy that is well-known for its corrosion resistance, which is mainly due to the inclusion of chromium (Cr) (ICDA, 2013). Stainless steel is mostly produced from recycled scrap and ferrochrome (FeCr), a relatively crude alloy of Cr and iron (Fe). FeCr is predominantly produced by the carbothermic reduction of chromite, a mineral belonging to the spinel group characterized by the unit formula [(Mg,Fe2+)(Al,Cr,Fe3+)2O4] (Haggerty, 1991; Paktunc and Cabri, 1995; Tathavakar, Antony, and Jha, 2005). Although Cr can occur in 82 different minerals, chromite is the only source of new Cr units that can be exploited in commercial volumes (Motzer and Engineers, 2004). Approximately 95% of mined chromite is used in the production of various FeCr grades, of which high-carbon and charge grade FeCr are the most common (ICDA, 2013)."

Feb 1, 2019