Search Documents

This report, the fourth in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more effectively extract and process mineral products. Environmental considerations, health and safety standards, price controls, inflation, material shortages, and more dependence on foreign imports were problems faced by the minerals industry. Although productivity increased for most mineral commodities, the annual rate of increase has slowed in recent years, indicating a maturing technological situation. Growing concern for energy resulted in increased interest and research in alternative fuel sources. The primary concerns of metallurgists were pollution control and improved efficiency and performance of metallurgical processes, especially for reduction of energy consumption.

Jan 1, 1974

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By Robert C. Bates

Variations in water percolation rates through saturated cohesionless hydraulic backfill (mill tailings) have been studied in relation to the many physical aspects of the system to determine the most important factors in causing these variations. A multivariable least-squares regression analysis of 135 separate tests shows that a reliable estimate of the water percolation rate through typical hydraulic backfill can be made if the bulk density (unit weight), specific gravity, and grain-size distribution are known or can be estimated. Equations for predicting percolation rate, coefficient of permeability, and seepage velocity are developed both for the range of data analyzed and for extrapolation. The prediction equations for use within the range of data studied are quite accurate, while the ones developed for extrapolation are less accurate but still give reasonable approximations of flow rates. The equations given are valid for cohesionless materials that are free of clays and micas, exemplified by classified mill tailings. The equation developed for predicting percolation rates is as follows: 1nP20 = 11.39147 + 2.853422 1n(VR X D10) + 0.1747436 VR X Cu -178.8039 D10 X D50 + 311.7034 (DSO )3, (1) where P20 = percolation rate, inches per hour at 20° C; correction factors for other temperatures are given in the text, VR = void ratio, dimensionless, D10 = effective size (diameter in millimeters of the 10-percent-finer grain size), Cu = coefficient of uniformity (ratio of the diameter of the 60-percent-finer grain size over D10), D50 = average size (diameter in millimeters of the 50-percent-finer grain size), and In = natural logarithm (log to the base e). The prediction equation for percolation rate is rather complicated, so for practical use a nomograph that simplifies the solution of the prediction equation was developed.

Jan 1, 1967

By S. L. Weber, D. E. Banks

"Silicosis was first reported by the ancient Greeks and is apparently as old as human history. The prevalence of this illness peaked in the last half of the 19th century and the early part of this century, when mechanized industry was developing and the relationship between dust exposure and disease was less well understood. Yet, even today in devel-oped countries, sporadic outbreaks of silicosis occur when workers are consistently exposed to silica particles of respir-able size (0.5 to 5.0 µm in diameter) at levels exceeding those recognized to be safe.Silicon dioxide or silica. is the earth's most abundant mineral. Silica is considered to be either free (i.e.. unbound to other minerals) or combined. Minerals with high amounts of free silica include quartz (including granite) flint. Chert, opal, chalcedony, and diatomite. Combined forms of silica are called silicates and include, among others, asbestos talc and kaolin.In the crystalline form, silica exists as quartz, cristobalite, and tridymite (Fig. 28). Of these quartz is ubiquitous in the environment and occurs as sand and as a part of many rocks. Cristobalite and tridymite occur naturally in lava and can be formed by the heating of quartz or amorphous silica. Cristo-balite is more tibrogenic than quartz. Amorphous silica is noncrystalline and, therefore, is relatively nontoxic and does not cause silicosis. It occurs as diatomite (skeletons of pre-historic marine organisms) or as vitreous silica (glass), the result of carefully melting and then quickly cooling free crystalline silica. Heating diatomite with or without alkali (a process known as calcining), forms cristobalite and adds the respiratory toxicity of free crystalline silica.There are many opportunities for occupational exposure to respirable crystalline free silica. Some of the commonly en-countered occupations in which the risk of silicosis exists are reported in Table 20.Silicosis. the pulmonary disease caused by the inhalation of silica particles of respirable size, is most commonly cate-gorized by findings on the chest radiograph. The most typical presentations simple silicosis and progressive massive fibrosis appear different radiologically but are grouped under the category of classic silicosis because they are a part of the radiographic spectrum of this illness. Radiographically, simple silicosis appears as small (less than 10 mm in diameter), rounded opacities, typically predominant in the upper lung zones. Progressive massive fibrosis is the result of the coalescence of these small nodular opacities and appears as larger opacities (more than 10 mm in diameter), again typicallydistributed in the upper lung zones."

Dec 1, 1995

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page Information Circular entitled "Mineral wool." This was one of the first publications to present to the public some technical aspects of the mineral-wool industry. Since that time several articles have appeared on the subject in the technical press as well as publications by State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large numbers, and in 1935 it was decided, with the cooperation of the is industry, to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for public distribution. As a first step, a brief questionnaire was mailed to the known producers asking if they would cooperate for publication. Favorable replies were received from of percent of the manufacturers, and the field work was started. As the study progressed and tie number of plants visited grew, it became more and more apparent that the industry had made rapid strides in technical operation and control of their product, as well as in increasing production during the mast decade.

Jan 1, 1938

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress -appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions end hearings2/ relative to the need for the survey, the opinion was expressed that crude oil held is storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to

Jan 1, 1938

By F. J. Wiebelt

Production of small tonnages of asbestos has been reported from 18 California counties; 16 additional counties have occurrences of asbestos. The counties in the northern part of California that have had a recorded production are: Alameda, Amador, Calaveras, Contra Costa, E1 Dorado, Napa, Nevada, Placer, Shasta, Siskiyou, Trinity, and Tuolumne. No deposit in the State has maintained consistent production. Serpentinized peridotites (potential chrysotile-bearing rocks) are widely distributed in the coast ranges, Klamath Mountains, and western foothills of the Sierra Nevada.

Jan 1, 1958

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

[Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand .for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions and hearing2/ relative to the need for the sway, the opinion ms expressed that crude oil held in storage for long periods had lost so much of its gasoline content that he economic significant of total stocks should be discounted materially. Therefore, a primary objective of the survey was to]

Jan 1, 1938

By Ott F. Heizer

This paper describing the mining practices at the mines of Massachusetts, Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in tie various mining districts of the United States. The author acknowledges the assistance of William C. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in the preparation of this paper.

Jan 1, 1930

By R. L. de Beauchamp

A preliminary investigation was made of the extraction of chromium from ferrochromium by low-temperature chlorination in the 3400 to 5250 C range. The objective was to devise a method for separating chromium from iron in high-carbon ferrochromium produced from domestic chromite concentrates. The majority of iron was removed as a volatile chloride; chromium was contained in the residue as a nonvolatile chloride, which was separated from carbon and unattacked ferrochromium by dissolution. A small rotary chlorination apparatus was designed, built, and used for the chlorination tests, and samples of commercial-grade high-and low-carbon ferrochromiums were chlorinated for comparison of chlorination characteristics. Low-temperature chlorination of three types of ferrochromium resulted in the removal of 81.9 to 91.6 percent of the iron content as sublimed FeC13. Recovery of chromium in a leach solution of the reactor product varied from 82.4 to 93.1 percent.

Jan 1, 1968

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960