Search Documents

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By W. W. Adams

The first full year of the second World War for the United States presented a picture of the metal-and nonmetal-mining 4 industry which, without proper analysis and explanation, would convey a distorted view of achievements during 1942, especially because employment at gold and silver (lode and placer) mines-the largest group-declined to such an extent that the over-all totals for the country were reduced even though increases were made at mines producing copper, lead-zinc, iron, miscellaneous metals, and non-metals. A complete panorama of the metal-and nonmetal-mining industry, exclusive of coal mining, reveals a decrease in the number of men employed, the man-hours of employment, and the accident-frequency rates. Were the gold and silver (lode and placer) mines to be considered as a separate category; it would be seen that the number of men employed at all the other groups of mines increased appreciably over 1941. These other increases must be considered important, since these mines produced the vital war minerals that made valuable contributions to the military successes of the United States and its Allies during the year. A separate analysis of each of the various groups of mines may be found elsewhere in this bulletin. For the purpose of maintaining continuity in this series of bulletins, however, the discussion in this introduction will be confined to the entire metal-and nonmetal-mining industry (excluding coal mining, for which a separate bulletin, No. 462, has been published).

Jan 1, 1945

By Kenneth L. Bickel

During an underground mine fire, the importance of controlling the spread of smoke and toxic gases with suitable ventilation structures has been proven. However, under certain conditions, control of the propagation of the fire itself may be even more critical in insuring a safe mine evacuation. Fire doors offer the means for accomplishing both objectives. In 1978, the Bureau of Mines initiated research to evaluate the state of fire-door technology and develop and test a fire door suitable for large openings (10 by 12 ft or larger) in noncoal underground mines. This report discusses current fire-door technology in the context of the underground mine environment and the design, fabrication, lab testing, and in-mine field testing of a mineworthy fire door. This door has a 1.5-h fire resistance rating and limits temperature rise across the door to 2500 F during the first 30 min of fire exposure.

Jan 1, 1987

By Richard J. Mainiero, James H. Rowland

When most people think of explosives transport they think of a hazardous operation. We all know that we aren’t allowed to transport explosives through tunnels and are discouraged from traveling through heavily populated areas. Popular opinion suggests that explosives transport is a very risky operation. The authors decided to look into this a little more thoroughly and found just the opposite to be true. While there have been some disastrous world-wide accidents involving the transport of industrial explosives, this is not the case in the U.S. Over the past 10 years, accidents related to the transport of explosives used in mining and construction have resulted in 5 major injuries, 11 minor injuries, and no fatalities. Explosives and ammonium nitrate (AN) transport outside the U.S. has not had such a good record; there have been 4 major explosives or AN transport accidents resulting in a total of more than 300 deaths. Most of these fatalities could have been prevented if the accident site had been evacuated once the explosive or AN cargo began burning. The safe history of explosives and AN transport in the U.S. is due to diligent efforts by government, labor, and industry. However, accidents will become more common and disastrous if we become complacent.

By J. Bennetts

As part of its mission to develop technology that will help increase the supply of critical and strategic minerals from domestic resources, the Bureau of Mines has investigated methods for beneficiating platinum-group metal ores from the Stillwater complex, Montana. This report presents the result of a bench-scale study employing froth flotation to recover a sulfide concentrate containing platinum-palladium values from a mineralized gabbro. Best results were obtained with a flotation scheme utilizing a mercaptobenzothiazone collector and sulfuric acid. Rougher concentrates containing approximately 11 oz Pt-Pd/ton and 90 pct of the metal values in the ore were obtained. Subsequently, cleaner concentrates containing approximately 26 oz Pt-Pd/ton and between 80 to 85 pct of the Pt-Pd values in the ore were prepared.

Jan 1, 1980

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

By B. M. Harra, O&apos

Zinc smelting is frequently termed a backward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, low-unit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pounds of ore. The diameter of the retort is limited by the time required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, or producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser attached to one end of the retort, where it condenses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls and of the ore charge itself, the heat efficiency even of the most modern regenerative furnaces is only about 12 per cent. The retorts have a short life, 30 to 60 days, at the high temperature required; zinc

Jan 1, 1923

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

By D. A. Buckingham

Engineering and economic evaluations were performed by the Bureau of Mines on 14 Frasch sulfur, 1 native sulfur, and 21 metal sulfide operations in 11 market economy countries. The evaluation included discounted-cash-flow rate-of-return economic analyses at 15 pct to determine the average total cost of production of these two commodities and the potential availability of elemental sulfur (8) and pyrite concentrate. The Bureau evaluated the potential availability of elemental sulfur and pyrite concentrate. Approximately 279 million metric tons (Mmt) of pyrite concentrate at 46 pct 8 is potentially recoverable from 422 Mmt of in situ metal sulfide ore. Nearly 89 pct of the total pyrite concentrate is available at an average total cost of production below the January 1984 pyrite concentrate market price ($43/mt). About 185 Mmt 8 is potentially recoverable from 253 Mmt of in situ elemental sulfur. About 99 pct of this sulfur is available at an average total cost of production below its January 1984 market price ($131/mt).

Jan 1, 1986

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coals; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fourth of a series of reports giving the results of studies by counties under phase (1) of the investigation. It covers Armstrong County, Pa., which comprises parts of the Foxburg, Clarion, Brookville, Kittanning, Bural Valley, Smicksburg, Freeport, Elders Ridge, and Indiana quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and more than 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By N. N. Moelbs

The U.S. Bureau of Mines is conducting research on many topics relating to the hazards of coal mining, increased production, and protection of the environment. One area of research that has received scant attention in recent years is that of water inflows, probably because few fatalities in the United States have been attributed to them. As mining goes deeper, the problem of water in 1ow could increase dramatically because of adjacent or overlying mines in which huge water pools are impounded. Inaccurate mine maps and ineffective barriers can constitute a serious problem for operators both from gradual inflows and sudden inrushes of water. This report describes a wide but ineffective barrier that permitted an average 240-gpm inflow to a developing mine from an adjacent mine. The anomalous geologic structure that facilitated this leakage is described, demonstrating that size, alone, is no assurance against serious leakage. Some recommendations for managing serious water inflow are included.

Jan 1, 1989

By Herman W. Hill

This report summarizes research into the root causes of failures in mine power systems which impact safety and reliability. Abnormally low fault currents, due to arcing faults, self-excited systems, and fallen trolley wires are examined and quantified. The reliability of components which are critical for safety is studied, as well as reliability of components which are crucial to the mining pro cess. Failure rates are found through in-situ tests, accelerated life tests, studies of mine maintenance, and fault-tree analysis. Reliability data is used to predict fatalities and lost-time accidents through computer-aided fault-tree analysis. Analytical support tasks reported include the deriving of trailing-cable ampacities under cyclic loading, and the measurement of connected ground beds.

Jan 1, 1981

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972