Search Documents

By James H. Cobbs

The purpose of this study is to investigate the application of boring equipment to the production of anthracite coal from steeply pitching beds. Both raise boring and augering equipment were considered. Previous studies (11) have indicated that boring equipment may have definite applications to the development of steeply pitching anthracite beds. This investigation was to carry forward previous work to determine the possible application of the two different types of equipment being considered. Previous conclusions have been substantiated by the results of this study.

Jan 1, 1975

By J. L. Kohler

The final report for Phase II of Bureau of Hines Contract J0134025 concerns the research and development of sensitive ground-fault relays for dc utilization systems in mining. Sensitive relaying employs very low pickup levels such that, when used in conjunction with very high resistance grounding, the exposure of a human to ventricular fibrillation is significantly reduced. To delineate the desired relay characteristics, the report begins by reviewing previous research in this area. A theory for the saturable transformer used to sense the fault current is presented. The design of the ground fault relay is described in sufficient detail that it may be duplicated. Test procedures and results are given. Finally, conclusions and recommendations related to Phase II are presented.

Jan 1, 1986

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By Joseph A. DeCarlo

The annual survey of the oven-coke industry by the Bureau of Mines, United States Department of the Interior, described in this report shows that 79 plants were operating in 22 States December 31, 1956. On that date 15,923 serviceable ovens existed, with a maximum total annual coke capacity of 79,965,100 net tons, and 631 new ovens were under construction. Their annual coke capacity was 3,307,300 net tons. The number of serviceable ovens in existence relates only to those capable of producing coke and does not include (1) any ovens that were blanked off or retired permanently in batteries that were operating December 31, 1956, and (2) ovens that had been demolished and were being rebuilt on that date. For this reason, the number of ovens at furnace plants reported by the Bureau of Mines at the end of each calendar year differs from the number reported for the same group by the American Iron & Steel Institute, as the institute includes ovens being rebuilt.

Jan 1, 1958

By J. R. Koehler

Effective barrier pillar design is essential for safe and productive underground coal mining. This U.S. Bureau of Mines report presents an overview of available barrier pillar design methodologies that incorporate sound engineering principles while remaining practical for everyday usage. Nomographs and examples are presented to assist in the determination of proper barrier pillar sizing. Additionally, performance evaluation techniques and criteria are included to assist in determining the effectiveness of selected barrier pillar configurations.

Jan 1, 1995

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By Scott W. Hazen

This report describes exploration for lead-zinc ores at the Madonna mine between 1945 and 1953 by the Utze Lode Co., the Bureau of Mines, and the company with Government financial aid under the Defense Production Act of 1950. The Madonna mine yielded silver, lead, and zinc with a net smelter value of over $5,000.000. from 1882 to 1924. The mine was inactive from 1924 to 1942 when the Utze Lode Co. acquired the property. Possibilities for finding ore in the mine, especially at depth, were considered favorable. The Utze Lode Co. began rehabilitating the Madonna mine in 1945. An exploration program, which consisted of winze sinking and drifting, failed to produce commercial are.

Jan 1, 1956

By R. L. Rankin

The program objective was to conduct surveys of respirable dust concentrations in coal mining operations at locations outby the working face. The results of these surveys were directed toward 1. identifying outby dust sources, 2. evaluating the severity of the major dust sources, 3. establishing dust sampling frequency, 4. establishing dust sampler locations, and 5. assessing the? areas of influence of the dust sources. The study included dust sampling of only nonhigh risk personnel and areas at six dif-ferent mines. Thirteen continuous mining, four longwall and two conventional mining sections were sampled. The severity of outby respirable dust sources such as load points, runways, dump points, beltways, transfer points and main haulage operations were characterized and areas within the mine were ranked according to severity. Information on engineering controls was also acquired. Guidelines for implementing a dust sampling program are presented and include sampler locations, ventilation surveys, dust surveys, effects of shift-to-shift variations, and sampling frequency.

Jan 1, 1980

By M. M. Kirk

Forced-air cooling of cold-mold arc furnaces for melting zirconium and similar metals has been investigated and found to be practical from the stand-point of heat transfer. It is believed that this technique offers a significant reduction in explosion hazard from that inherent in water cooling, the current industrial practice. A copper crucible, with longitudinal, integral-type fins and with an outer jacket to confine the airstream, appears to be the best general design for air-cooled operation. Cutting the fins into short segments and bending the segments to produce a herringbone effect increased the airstream's turbulence and was found, on test, to increase the heat transfer up to 35 percent.

Jan 1, 1959

By Forrest T. Moyer

The safety record of the metal mining and milling industries in 1965 is reviewed by the Bureau of Mines. The overall injury-frequency rate of 23.77 per million man-hours was 5 percent lower than in 1964 and was the lowest annual rate in a statistical history beginning with 1931. The injury-severity rate of 3,521 days lost per million man-hours in 1965 represented a 5-percent improvement over 1964. However, the total of 3,825 disabling work injuries comprised 61 fatal and 3,764 nonfatal injuries, one and 92 more, respectively, than in 1964. At primary nonferrous smelters, refineries, and reduction plants, the injury-frequency rate of 8.97 per million man-hours in 1965 was 13 percent lower, but the severity rate percent higher than in 1964. these plants in 1965, 4 more of 1,173 days lost per million man-hours was 17 There were 12 fatal and 971 nonfatal injuries at and 28 fewer, respectively, than in 1964.

Jan 1, 1969

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By M. M. Wong, J. E. Klosterman

Scrap beryllium chips ( nominally 96 to 97 percent Be ) were electrore fined in a prototype cell with 408 lb of electrolyte composed of 52.4 mole - percent LiCl , 36.3 mole - percent KC1 , and 11.3 mole - percent BeCl2 . The cell temperature was 500 ° C. In a typical 10-3 /4 - hour deposition cycle , 0.415 pound of metal was produced ; the metal contained impurities in parts per million as follows : C , 700 ; 0 , 610 ; Al , 34 ; Ca , 32 ; Cu , 20 ; Fe , 25 ; Mg , 9 ; and Mn , 23 . Operation of the prototype cell for 2 years demonstrated that adapting the electrorefining process to an enlarged scale of operation presented few difficulties in mechanical functions , maintenance of optimum operating conditions , and control of product purity . After the spent anode feed was leached in a 5 - percent nitric acid solution and the fine - sized particles were removed , it was recycled in some tests . The metal produced was somewhat higher in impurities than metal from the fresh scrap chips .

Jan 1, 1964

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By Edwin C. Reeder

This is one of a series of papers dealing with mining methods and costs prepared under the sponsorship of end in cooperation with the United States Bureau of Mines. The mining methods described in this paper are those used in one of the large mines producing fluorspar in the Kentucky-Illinois fluorspar field, located in southern Illinois and western Kentucky on the Ohio River. The occurrence of ore and the methods of wining are similar to those in other mines in the district; therefore information regarding methods and the results obtained should be of interest. Improvements in methods have been made as experience developed the need of them. The trine is situated at Rosiclare, Ill., on the Illinois Central Railroad, and shipments are also made b r barge on the Ohio River.

Jan 1, 1930

By Robert H. Ridgway

This circular outlines salient facts regarding the pyrites industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The United States Bureau of Mines has in its files additional and more detailed data upon many of the subjects presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. The bureau will welcome comments, criticisms, and contribu- tions of data that may assist in making later editions of this circular of information more accurate, or may aid in developing more fully the files pertaining to pyrites.

Sep 1, 1931

By F. E. Block, Robert R. Brown, A. W. Henderson

The chlorination of Cr₂ 03 (chromic oxide ) in the presence of carbon with CC14 (carbon tetrachloride ) and COCl2 (phosgene ) chlorinating agents was investigated by employing the radioactive tracer carbon By tagging carbon mixed with Cr₂ 0з , the chlorination reaction was evaluated in terms of the competitive reaction of the elemental carbon and the carbon contained by the chlorinating agent . A unique gas - analysis train was used to separate the chlorination product gases ; CO , CO₂ , and COC12 . The C¹ activity of the gases was determined and used to calculate the reactivity of each source of carbon . Reactivities were determined for the temperature range from 600 ° to 900 ° C. The results of the investigation show that each source of carbon reacts significantly with the Cr2 03 and that the reactivity of each form of carbon depends on the reaction temperature , and each form is independent of the other . Radioisotope and gas - analysis techniques are discussed and a description of the experimental apparatus is given .

Jan 1, 1964

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By J. F. Shaw

MINE fires are usually extinguished by constructing seals in the approaches to the areas to exclude air from the fire areas, which smothers the fires in an oxygen-depleted atmosphere. Seals should be substantially constructed and made as nearly airtight as possible and should be provided with a sampling pipe so that samples of the atmospheres behind the seals may be collected at regular intervals. Methods of constructing seals and of sampling and analysing mine atmospheres are fully described in Bureau of Mines publications. (1, 2). Information obtained on the composition of atmospheres behind fire seals is helpful in determining if a fire has been extinguished or if there is any danger of an explosion when a fire area is being sealed or unsealed. The progress of a mine fire can best be determined by studying percentages of carbon dioxide, carbon monoxide, and hydrogen in the atmosphere behind the seals. Hydrogen will be formed in a bituminous- or subbituminous-coal mine when the temperature exceeds 480° F. and in an anthracite mine when the temperature exceeds 660° F. (3). Carbon monoxide and carbon dioxide are both products of combustion of coal, wood, or other organic compounds. The presence of carbon monoxide has long been accepted as an indication of a mine fire. A sealed fire area should not be reopened until the carbon monoxide has disappeared. Trends in the percentage of carbon dioxide are also useful in determining the status of a mine fire. Carbon dioxide is sometimes liberated by rock strata. In this case, carbon dioxide in the atmosphere behind a seal will be from two sources-the rock strata and the fire. When the, fire is extinguished, carbon dioxide will be liberated from only I source, the rock strata, and when the percentages of carbon dioxide are plotted, the slope of the curve will not be as steep as when this gas was being liberated from 2 sources. If the only source is the fire, the percentages of carbon dioxide will gradually decrease after the fire has been extinguished. By studying analyses of a mine-fire atmosphere, it is possible to determine if the atmosphere is explosive; if the mixture is capable of becoming explosive when mixed with air; and if the mixture can be made nonexplosive or be prevented from becoming explosive by being mixed with an inert gas. These factors can be computed mathematically or determined graphically. The mathematical calculations advanced by Ash and Felegy (7) are discussed, and graphical solutions of their equations are presented. It is believed that the graphical solution will be extremely helpful in determining the characteristics of a mine-fire atmosphere when fighting a fire, because the results can be obtained in a matter of minutes, and there is less likelihood of an error being made under the stress incident to control efforts. The experimental and theoretical work upon which the formulas are based have been adequately described and are not discussed at this time (5) (6).

Jan 1, 1955

By Peter Grandone

Bureau of Mines engineers engaged in studying stimulative methods of recovering oil have been making a series of tests on the effectiveness' of methods that may be applied in water flooding oil-bearing sandstones. The report gives the test procedures and results of a study of the rates and pressures used for injecting water into several sandstone formations in the Mid-Continent fields for the purpose of learning more about the mechanics and efficiency of the flooding process and to provide useful information for operators of water floods in this area.

Jan 1, 1949