Search Documents

By William L. Crentz

In a Nation-wide appraisal of coking-coal reserves and of the practicability of upgrading marginal deposits to metallurgical standards, this study of the preparation characteristics of the coals in Cambria County, Pa. , was undertaken. Over 90 percent of the coal remaining in Cambria Comity is found in the Upper Freeport, Lower Freeport, Upper Kittanning, and Lower Kittanning beds. The Middle Kittanning bed, although mined on a commercial scale in the past, is not an important bed now, as most of the remaining reserves are too thin to be mined over wide areas. For many years, Cambria County has been an important source of coal for industrial and metallurgical purposes. The) principal production comes from the Lower Kittanning bed, which accounts for almost .60 percent of the Cambria County coal output. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1950

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau's Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983

By Robert N. Roby

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to Department of Interior agencies and others concerned with the planning of the proposed Federal power developments within the Missouri River Basin . The present report has been designed to permit public distribution of the factual data obtained . The field investigations in Meagher County were made during tually all 1948 ; Vir- known metallic mineral occurrences within the county were investigated ; some nonmetallic mineral deposits also were investigated . The investigations cannot be considered complete , however , because some long-inactive mines or prospects may have been missed . Most of the old mine and prospect openings are caved; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

In This Chapter [Finding the dust source Ventilation and dust collector malfunctions Upgrading the dust controls Design stage ventilation planning ] This chapter explains how to reduce respirable dust76 in hard-rock tunnels during excavation by using tunnel boring machines (TBMs). The first steps in combating a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. If the ventilation system and dust collector are operating properly, then other dust controls such as water sprays and conveyor belt scrapers must be upgraded. For tunnels in the design stage, recommended air quantities are provided. FINDING THE DUST SOURCE AND LOOKING FOR VENTILATION MALFUNCTIONS [The first steps in fighting a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. Without knowing the exact source, efforts to reduce dust are hit-and-miss (mostly miss).] Taking samples to pinpoint the dust source. In tunnels with high levels of airborne dust, the first task is to pinpoint where the dust enters the airstream. Most dust originates from rock breakage at the tunnel face, but the location where this dust enters the airstream can vary. Dust can leak from behind the TBM face shield, from gaps in the ventilation duct, or from a mal-functioning dust collector. It can be entrained into the air from the muck on a moving conveyor belt. It can even be shaken loose from the underside of the belt as it passes over the idlers. As a start, to locate the dust source, dust samples and air quantity measurements should be taken at the following locations:

Jan 6, 2003

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

By S. E. Khalafalla

In support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has investigated a novel hydrometallurgical system with sulfur dioxide. Differential leaching with dissolved SO2 of manganese, nickel, and cobalt from their hydrous oxides was found to be very rapid and efficient--almost instantaneous and quantitative. In this method a given weight of mixed oxides previously ground to minus 200-mesh is slurried with a leach solution containing a specified quantity of dissolved SO2 for 10 minutes at room temperature and ambient pressure. An empirical leaching parameter, R, is defined as the ratio of the number of SO2 moles in the leaching solution to the weight of the metal oxide charge. Plots of the variation of metal extraction with the ratio R generate a series of sigmoidal-shaped curves, each of which is characteristic of a specific metal extraction. A threshold value of R is required to initiate the leaching of a given metal from the mixed oxides. Once this threshold is reached, the metal recovery can increase to more than 95 pct in very short times. For increasing values of R, the extractability of various metals by SO2 follows the order: Mn > Ni > Co >> Fe, Al, Cu. Differences in the threshold R values permit a variety of metal separations to be made simply by adjusting the quantity of SO2 in the contacting solution. Success in this leaching system depends upon comminuting the sea nodules to less than 0.149 mm (100-mesh). Above this critical size, leaching is slowed due to the inaccessibility of inner particle reacting groups to the SO2 leaching agent. This results in nonselective extraction and less extraction of preferred metal values. At or below 0.149 mm, leaching by SO, is possible with all its attributes of selectivity, sensitivity, and rapidity. Leaching with HC1 solutions of the same pH level as dissolved SO2 yielded mixed, slow, and incomplete metal extractions. This observation rules out any interpretation based on hydrogen ion as the leaching agent. The leaching curves resemble the complexometric titration curves of heavy metals with specific coordination species.

Jan 1, 1981

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931. The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results of other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time each sample was taken will also be reported.

Jan 1, 1932

By M. L. Whisman

The Bureau of Mines developed and tested in the laboratory several innovative techniques for reclaiming used lubricating oil. These processes included percolation through both chemically treated clay and ion-exchange resins, distillation through batch and continuous wiped-wall vacuum apparatus, treatment with solvent extraction systems, and chemical removal of impurities with chelating agents. In each treatment, the criteria of evaluation was oil recovery and reduction of acidic and metallic components. Both vacuum distillation and solvent treatment ranked high in their abilities to remove acidic and metallic components of the used oil with good oil recoveries. A combination of the two techniques gave the best overall results in terms of quality evaluations made by established bench tests. The methods were not ranked according to economic practicablity.

Jan 1, 1974

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining' the potential fur reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Roger G. Long

In May 1973, the Bureau of Mines asked Arthur D. Little, Inc. (A DL) to investigate existing industrial communication standards that may be applicable to the problem of developing standards for mine communication, considering that the standards that may ultimately be developed will require simple field procedures for the industry and the inspectorate to determine that communication systems are properly functioning. The emphasis on this study is on telephone communications as related to coal mine applications. B. TASKS The tasks agreed upon for this program were as follows: 1. "Investigate the current practices and existing standards of other industries under government regulation. 2. Determine applicable methods for industry personnel and inspectors to ascertain conformance on-site with minimal test hardware. 3. Review the Bureau's approval, testing and inspection procedure as it may impact the development of such standards. 4. From the above studies investigate the development of installation and performance standards for mine communications, including voice and telemetry. 5. Prepare a written report specifying what standards and field inspection techniques are applicable with recommendations for development of subsequent data and ultimately standards and field inspection techniques. 6. Prepare a written summary of the findings of various investigations with an appendix covering the detailed findings of each investigation. 7. Prepare a list of suggestions of additional assistance the Bureau might require in subsequent phases of developing communication standards and means of ascertaining performance."

Jan 1, 1973

By Rolland L. Blake

The Bureau of Mines investigated the mineralogy, tonnage, and beneficiating characteristics of oxidized (nonmagnetic) taconite iron resources of the Western Mesabi Range as part of its program to insure adequate future domestic mineral supplies. Magnetic taconite currently provides about 95 pct of Mesabi production, but the large tonnages of oxidized taconite between the magnetic deposits will be needed to help meet future domestic demand for iron ore. Three bulk samples that represent large tonnages from the Western Mesabi Range were selected to determine their mineral composition and liberation by light optical microscopy and to test their beneficiating response. This report describes the mineralogy and liberation characteristics of the three samples of the Biwabik Iron-Formation for 26.5 mi (42.7 kID) from Keewatin to Grand Rapids, MN. (Details of response to beneficia-tion were reported previously.) The samples represent mostly material from the Lower Cherty Member of the Biwabik-Iron Formation, although one sample included some Upper Cherty Member. Minerals of all three samples were quartz (chert), hematite, goethite, and minor to trace amounts of magnetite, iron carbonate, and iron silicates. It was concluded that the oxidized taconites of the Western Mesabi Range represent a subeconomic indicated resource that can be selectively mined and beneficiated as a future large source of iron feed for steelmaking.

Jan 1, 1983

By J. H. East

"INTRODUCTION .Very little information regarding coal mining in Spain has been published in the American technical press, and few people realize the extent of this industry or the conditions under which coal is mined. The information in this publication was collected in 1945 and consists of personal observations in Spain, statistics, and other data of a, general nature obtained from official sources.Spain produces bituminous coal, lignite and anthracite, but the total tonnage mined is less than the national requirements. Before the war, an appreciable tonnages coal was imported from Great Britain under the Anglo-Spanish treaty, which rebated import duties and effectually prevented competition from any other foreign source. The war stopped the major part of the important of British coal and caused rapid expansion of the domestic sources, but this was not sufficient to supply the industrial demand. Coal that formerly was not acceptable to industry because of quality is now mined and marketed. The Government, allocates the better-grade bituininous coal to the various industries in accordance with the national importance of the work in which they are engaged; for example, the railroads are allotted 100 percent of their requirements, but cement companies can obtain only 25 percent.The Government offered to inducements to increase the production of coal of any class, but the larger part of the increased tonnage obtained was in inferior grades; as a result, the lignite production was taxed, while a bonus was paid for bituminous-coal production in excess of the 1942 tonnage.The anthracite and bituminous-coal areas were severely damaged during the Civil War and many experienced miners migrated to the lignite mines in eastern Spain. This has resulted in an acute shortage, particularly the Province of Oviedo where the most important bituminous-coal deposits are located."

Jan 1, 1947

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992