Search Documents

By John L. Dahle

This report documents the research efforts that were undertaken to design, install and test noise abatement devices for use on off-highway haul trucks operating in surface mines. The objective of the program was to reduce the environmental noise from haul trucks. The noise reduction devices that were developed utilized existing technology and were tested on a 50-ton haul truck. The efforts emphasized the reduction of noise emitted from the engine compartment which included the use of side shields, sound absorbing material, improved radiator shroud design, and a modulating clutch fan. Noise tests were conducted using modified SAE test procedures for measuring sound levels around a stationary and moving machine, and inside of the operators compartment. Test results showed a maximum of 4 dB(A) reduction measured 16 feet from the truck. Interior cab noise was reduced 6 dB(A) with the windows and vents closed.

Jan 1, 1983

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By Alexander Siefert, Steffen Pankoke

In the development of commercial vehicles as well as of passenger cars, the effects of vehicle vibrations on operating safety, health and comfort can only be predicted by numerical simulation when appropriate occupant models are available. Such models must be based on human anatomy and have dynamic properties of real humans in order to achieve realistic results. Since human dynamic behavior depend on posture and percentile, the occupant model needs to be adjustable to these parameters with respect to geometry and dynamic properties [1,2]. Dynamic Human Finite-Element-Model CASIMIR CASIMIR is a non-linear, dynamic finite-element-model of the human body. It consists of a dynamic model of the upper torso with head, neck, shoulders and arms as well as of a dynamic model of the lower extremity with pelvis and legs. The most important part is the lumbar area with dynamic non-linear models of the lumbar spine and of back and abdominal musculature. The frequency-dependent characteristics of the intervertebral discs and the effects of muscle activation and non-linear frequency-dependent muscle properties are included. In the latest stage of development, CASIMIR has been equipped with a compliant model of the body surface in the contact areas to the seat. This results in a very realistic transmission of static and vibrational forces into the human body, see fig. 1. Intense model verification and validation has been performed in all stages of model development, starting with validation of small components like intervertebral disc, ending with validation of whole-body-vibrations using measurements of the dynamic mass / mechanical impedance [4]. For an in-detail examination of stresses in the vertebral bodies and discs, a non-linear submodel of the lumbar spine with an increased number of degrees of freedom can be coupled to the whole-body-model, enabling the researcher to examine local effects of vibrations and single shocks on the lumbar materials. [ ] Since it is well known that human dynamic behavior is significantly affected by anthropometric data and posture, CASIMIR can be individualized to the anthropometric status of single individuals or to the mean values for specific percentile groups. Furthermore, posture can be adjusted to the seating conditions applicable to a specific vehicle. Posture modification capabilities include the variation of the lumbar lordosis [3].

Jan 6, 2006

By G. L. Oldright

This paper is the thirteenth of the series on Smelting in the Lead Blast furnace, and the third of the series on Handling Zinciferous Charges. Two other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By Frank C. Morris

It is generally recognized that the productivity and ultimate recovery of an oil well may be reduced as a result of reduction in permeability of the sand at the well bore by invasion of filtrates and clay particles from drilling fluids. As a means of determining whether a sand has been "damaged" from these sources, several investigators2 3 4 5/ have developed methods of analysis based on the rate of increase in bottom-hole pressure while a well is shut in. Because of growing recognition of the importance of completion practices as related to the quantity of oil that may be recovered from wells, the Bureau of Mines has studied completion practices in California and the Midcontinent area. Well-interference and pressure-buildup tests were completed Ear seven wells in the Scurry Reef field to determine the effective permeability in the reservoir.6/ Also, a study was made of the pressure-decline curves obtained from 35 water-input wells in 5 different production areas of northeastern Oklahoma and eastern Kansas.7/

Jan 1, 1957

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939

By Jeffrey Johnson, Carl Sunderman, Ted Williams, Stephen Signer, Douglas Bayer

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company’s Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and-MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff of the Explosives Division of the Bureau of Mines and, are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes, of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more' rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about I millisecond after the shpt is fired is illustrated in figure

Jan 1, 1939

By R. M. Santmyers

Caesium, rubidium, and lithium are sometimes described as the minor or rarer alkali metals. They generally occur together in nature, although, lithium is distributed more widely and is far more abundant than either of the other two. The chemical, and even the physical, properties of these three elements can best be considered In conjunction with the more familiar members of the alkali group, sodium and potassium. The five elements lithium, sodium, potassium, rubidium, and caesium show an interesting gradation properties from member to member with the increase in atomic weights. All are silvery white and soft enough to be cut with a knife. They tarnish rapidly in air and decompose water at ordinary temperatures. The lowest temperature at which the action of the several metals on water can be de¬tected is -98°C. for sodium, -105°C, for potassium, 108°C. for rubidium, and -116°C. for caesium. The chemical activity appears to increase steadily from

Jan 1, 1930

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

The investigations reported herein comprise preliminary studies to evaluate large scale mining systems adaptable to the thicker oil shale deposits in the deeper central portion of the Piceance Creek Basin. The studies include an evaluation of the geology, hydrology and resources of the Basin., evaluation of a potential prototype mine site, synthesis of rock mechanics data on Green River Formation oil shale, selection and preliminary design and cost evaluation of six potential mining systems and a ranking analysis to aid in selecting the most promising system. Results of the ranking analysis indicate the following four systems to be most promising for large scale underground oil shale mining: - Chamber and pillar (using spent shale backfill) - Sublevel stoping with spent shale backfill - Sublevel stoping with full subsidence - Block caving with LHD's Recommendations for phase II are to investigate the above systems in greater detail, refine present cost data, and perform economic evaluations of oil shale mining using these systems.

Jan 1, 1975

By R. Duncan Gardner

This paper describing the milling practice at the concentrator of the Harmony Mines Co. is one of a series being; prepared by the Bureau of Mines on milling methods and costs in the United States. For the period February 15, 1929, to June 1, 1929, the concentrator treated 200 tons of copper ore per day containing 3.84 per cent copper and recovered 99.2 per cent of the total copper in concentrates averaging 26.61 per cent copper. Milling practice at the Harmony Mines is in most respects similar to the usual practice at the average flotation concentrator producing bulk flotation concentrates. The exceptionally high recovery is due to a number of minor conditions. These minor details will be stressed throughout this paper.

Jan 1, 1930

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By M. M. Fine

Chalcocite flotation concentrates (26-34 percent Cu and 6-7 percent S) were roasted in air to determine sulfur elimination as a function of temperature, airflow rate, and residence time. Fluosolids roasting was evaluated batchwise and continuously in a 4-inch fluid-bed reactor. Kiln roasting tests were carried out in a 4-inch ID by 6-inch-long rotary drum. Pelletizing the very fine concentrates prior to roasting was essential to minimize dust losses and accretions. Concentrate pellets, sized minus 10 plus 20 mesh and bonded with 2 percent bentonite, were excellent feed for fluosol¬ids roasting and limited dust losses to 10 percent or less. One-fourth-inch pellets were best suited to kiln roasting. Both techniques were capable of producing copper calcines analyzing well under 1 percent residual sulfur when operated at 900° C with average retention times of 3 to 4 hours. Calcined pellets were strong, porous, and readily reducible.

Jan 1, 1970