Search Documents

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By Javier Illanes, Felipe Moroni

In recent years, implementation of Artificial Intelligence and Machine Learning model technology has gained ground in almost every aspect of human activities. The mining industry has not been foreign to these applications, with advantages including the creation of new optimization methods and the elimination of repetitive tasks. Those applications have been implemented in multiple operative areas, from preventive conveyor belt maintenance to energy optimization for minimizing environmental impact. The blasting process aims to use the energy liberated by the detonation of explosives to break the rock mass according to specifications that facilitate the comminution process. To optimize this process, the energy delivered must correspond to the necessary amount to exceed the tensional and compressional resistance of the rock mass. If the energy applied is insufficient, the rock will not reach the desired fragmentation level and the processing plant may incur additional costs. On the other hand, if the energy level required is exceeded, we incur increased blasting costs that correspond to excess explosive used. Optimization of this aspect of the mining process has major impact in the processing chain reflected in lower costs, efficient resources consumption and environmental impact. The Design for Outcome technology (DfO), developed by Orica, is used to characterize the rock mass in detail to classify, borehole by borehole, the rock mass relative hardness to deliver the adequate energy level to achieve optimal fragmentation. This technology uses information collected by drill sensors, producing data typically referred to as Measure While Drilling (MWD) data to classify the rock mass into domains that can later be used to apply optimal blast designs. In DfO, the data flow is fully automated, starting with the data produced by the drilling system and uploaded to the cloud, which is then domained using Machine Learning (ML) techniques, and then published for consumption using a web interface. Automated explosives loading rules are then generated for each rock mass domain, ensuring that for each borehole, the adequate explosive energy is delivered to achieve the desired fragmentation results with unprecedented accuracy. The application of machine learning techniques allows us to optimize the blasting process results by leveraging a deeper understanding of the rock mass. Applying these optimization techniques, we obtain considerable economic benefits, decrease resources consumption, and achieve a more sustainable mining operation. The application of DfO in a Chilean mining operation allowed the characterization of their rock mass into four domains and established specific explosive loading rules for each one. A 60kUSD reduction in explosives cost was achieved during the test period, while maintaining the desired fragmentation results and expected dig rate. These outcomes were the result of a comparison between the blasting costs used applying the technology mentioned above and a “traditional” classification of the rock mass with the corresponding blasting practices.

Jan 21, 2025

By Matthew Clay, Colin Chambers, Susan Hookham

Opencast (quarries) and underground mines around the world use blasting methods to mine valuable ore. Traditional blasting systems use technologies such as electric delay detonator systems (developed in the 1950s) and non-electric detonator systems (developed in the 1970s) to initiate a detonation train to blast rock more effectively, and so retrieve valuable product more efficiently. However, the lack of precise control over blast timings with these approaches can result in undesirable outcomes such as significant flyrock, excessive ground vibration, uneven grade of rock and misfires (in which sections of the blast can remain unfired). The development of Electronic Initiation Systems (EIS), first used in the 1990s, introduced a higher level of control over the blast. These systems greatly reduce the negative issues associated with blasting. However, this precision introduces complexity, and with this complexity comes difficulty in demonstrating the predictability, safety and reliability of such systems.

Jan 1, 2017

By Paul Klaric, Nicholas Bodley

Every blasting engineer or professional can attest to the age-old conundrum of obtaining accurate hole information on a large scale prior to loading explosive charges in a blast hole. Even though the benefits of QA/QC are well known and documented and are becoming increasingly important when digitizing and automating mining operations, the QA/QC process itself has not changed significantly over generations. The current methods where operators deploy measuring tapes of variable standards recording their subjective assessment of hole length on a paper blast map or manually transcribing to a tablet, are unreliable and non-auditable. Additionally, the process in its current form is time intensive, obtaining only moderate results and benefits, making it difficult or impossible to resource in today’s tight labour markets. Often only two data points, depth, and water presence, are captured when visiting the hole resulting in a high cost per bit of data. For these reasons, the process is seldom done on a large scale, let alone integrated. The QA/QC process in its current shape is a gap that will need to be addressed if autonomous blasting and mining is to become a reality.

Feb 6, 2023

By N Gkikizas-Lampropoulis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper interprets previous experimental information on the effect of delay on fragmentation with the aid of some new experimental observations of the time of detachment of the free face of the blast as well as results of numerical modelling. It was shown that detachment of the burden occurs at delays shorter than the one which produced optimum fragmentation in the experiments, suggesting some fragmentation improvement due to gas action. In addition, at the spacing to burden ratio of the experiments, the damage zone from an earlier detonating charge extends the distance to the neighboring charge, essentially affecting the burden of some of the holes of the blast, at detonation time. Computer modelling demonstrated that increased spacing results is less overlap of stress induced damage zones meaning that there is less influence of delay on stress wave induced fragmentation. It was also shown that simultaneous initiation results in less back break, while increased back break may result even with short delay times.

Jan 1, 2016

By Catherine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his suppher specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation. The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1992

By John Hutchings

Drilling and blasting is a clearly delineated work process, which has well defined inputs and outputs. Drilling and blasting is also a process with a number of steps each of which has measurable outcomes. Drilling and blasting is ideally suited to the application of Total Quality Management principles. Most drilling and blasting information is generally poorly managed with disjointed and unrelated Information Technology systems managing parts drilling and blasting data. Data is often moved from on system to another, sometimes manually. In the field, drilling and blasting is still very much a paper based system and which has not generally benefited from some of the recent hardware and software technology advancements now “on the shelf”. Data collected on paper rarely is transcribed back into an electronic system for further analysis. It is often difficult to collate or review historic drilling and blasting data. This paper will present a definition of Total Quality Management and demonstrate how it can be applied to the drilling and blasting work process. Total Quality Management defines the mechanisms for the application of continuous improvement to drilling and blasting. Continuous improvement will provide opportunities to modify drilling and blasting work process outcomes and generate real cost benefits within the overall mining process. A complete drilling and blasting management system frame work, called DBS, is presented in this paper. DBS provides all the components necessary to implement a full drilling and blasting Total Quality Management solution. Also highlighted will be appropriate “off the shelf” technology that can be applied to replace current paper based systems and provide the means to connect with other mine data systems. Various examples will be discussed which will demonstrate potential benefits of applying a structured Total Quality Management approach to a drilling and blasting work process.

Jan 1, 2004

By John Montgomery

This paper discusses the major changes to the Commissioners Rules and Regulations, Chapter 120-3-10 “Rules and Regulations for Explosives and Blasting Agents”; how the changes came about, and a summary of the status of the blasting industry in Georgia.

Jan 1, 2003

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper in which he presents his own A factor. Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blast hole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, e.g. in conjunction with image based fragmentation measurements or crusher modeling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function such as in the KCO model.

Jan 1, 2016

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By LaRay Collyer

San Juan Mine began pre-splitting the highwall prior to cast blasting in August 1986. The first pre-split shot used six inch PVC (polyvinylcloride) pipe inside a 10 5/8 inch hole, drilled at a 74 degree angle. The powder factor was about .90 pounds per cubic yard.

Jan 1, 1990

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Robert Hopler

Torpedoing Wells. – On the completion of the drilling, or when the production is found to decrease, it is usual to “torpedo” the well to increase the flow. This process was patented in 1862 by Colonel Roberts, who believed, with many others, that the oil was contained in crevices in the rock, which might not have been tapped by the bore-hole. He therefore proposed the use of nitroglycerine, gunpowder, or other explosive, to break up the rock at the bottom of the well, so that these rich “pockets” might be brought into communication with the well.

Jan 1, 2007

By A T. Spathis, M G. Wheatly

Some preliminary dynamic pressure data were obtained from several charges detonated in a tunnel situated in massive granite rock. The context of the work is the potential for desensitisation of explosives, failure of detonators, and sympathetic detonation due to the close proximity of inter-hole and inter-deck explosive charges to each other. Dynamic pressures were measured using piezoelectric gauges in water-filled 45 mm diameter holes adjacent to the charges. Some of the first arrival peak pressures were noisy, and although not fully resolved, may be due to reflections and the physical arrangement of the transducers and their size with respect to the monitoring holes. The estimated peak pressures were between 0.1 to 8.7 MPa at approximate distances of 2.8 to 0.8 m, respectively. Further work is planned with gauges that are disposable, have a higher pressure range, and can be used within a few borehole diameters rather than the piezoelectric gauges used in the present work.

Jan 1, 2016

By Eduardo Lozano, Vilem Petr

The use of explosives bring countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition or avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation. The goal of this paper is to provide a solution against the hazards which unfortunately accompany the use of explosives. For this reason, a blast shield is specifically designed and tested for protecting personnel against these unpredictable effects. This document will develop a complete analysis answering the following questions: what are the potential hazards from an air blast; what are their effects; and how can we be protected against them. In order to answer these questions, theoretical, analytical, and numerical calculations are performed. Finally, a full blast shield prototype is tested under blasting conditions proving its effectiveness as a safety device while explosives are used.

Jan 1, 2015

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023

By Travis Davidsavor, David Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines. Existing pipeline company standards would have effectively precluded the construction of the replacement pipe by blasting rock. To facilitate the required construction and evaluate actual pipe stress during blasting to ensure pipeline integrity, a comprehensive evaluation methodology was developed by a team of pipeline, mechanical, geotechnical, instrumentation, and blasting engineers. A total of 60 strain gages were affixed to the steel pipe and seismographs were buried at the surface near the blasting area. Test blasting allowed pipe stresses with corresponding ground motion to be monitored. A conservative analysis approach evaluated individual peak strains and revealed that only small pipeline strains, and therefore stresses, were induced in the pipeline as a result of blasting. This evaluation allowed specific procedures to be developed to inform the blasting operation of maximum explosive loading and minimum charge distances. Additionally, this effort provided the pipeline operator with appropriate pipeline operating pressures during blasting activities to limit total stresses in the pipeline to be below allowable stresses imposed by code, regulators, and company operational limitations. Recommendations were developed to measure the blast generated ground vibrations with seismographs buried at the depth of the pipe, near the pipe, and limit the ground vibrations from blasting to 150 mm/s (6 in/s). If ground vibration intensities of 120 mm/s (4 in/s) or more were observed, additional engineering review is recommended. Finally, all blasting would be suspended and all activities reviewed at peak ground vibration intensities of 230 mm/s (9 in/s). The evaluation effort resulted in effective and efficient construction of the pipeline replacement and allowed the pipeline operator to better understand blasting induced stresses on their assets.

By Dale S. Preece

A new three dimensional (3D) mechanistic model of fragmentation, called the Fracture Density Model (FDM) is used to simulate full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. The model uses several computational mechanics algorithms to simulate the effect of blasting in different rock types

Feb 1, 2020