Search Documents

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By Masanori Mori, Hajime Miki, Osamu Ichikawa, Tsuyoshi Hirajima, Mitsuru Sawada, Keiko Sasaki

For pretreatment of selective flotation, surface oxidation of chalcopyrite and molybdenite was applied by oxygen plasma then the minerals were washed by solution at pH 9 with oxygen bubbling. Surface characteristics of these minerals were investigated with AFM, XPS, zeta potential and contact angle measurements. Contact angle of chalcopyrite and molybdenite decreased a lot by plasma treatment. When they were washed with pH 9 solution with oxygen bubbling, contact angle of molybdenite increased whereas chalcopyrite one kept low. Adhesion force measurements indicated similar behavior. Result of flotation experiments indicated low recovery of both chalcopyrite and molybdenite after plasma treatment and only molybdenite recovery became higher after washing. Selective flotation of chalcopyrite and molybdenite could be achieved with this process. Possible mechanism of selective flotation was proposed from the results of XPS, AFM, etc.

Jan 1, 2014

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018

By Z. A. Zhou

In Canadian oil sands processing, flotation is used to recover liberated bitumen droplets from oil sands slurries. Similar to conventional mineral flotation practice, a fundamental limitation of recovering bitumen from low grade oil sand ores is its slow and ineffective aeration of the liberated small bitumen droplets. Gas nucleation and cavitation could provide better mechanisms for accelerating bitumen-bubble attachment. A research program was undertaken to examine factors affecting spontaneous bubble nucleation on bitumen surfaces. The results demonstrate that surface hydrophobicity and existence of gas nuclei in process water play a critical role for bubble nucleation. While there are more bubbles nucleated on highly hydrophobic silanated glass surfaces than on moderately hydrophobic bitumen, bubble nucleation on clean hydrophilic glass surfaces is negligible. Heating process water up to 85 ~ 95oC (as used in commercial operation) or boiling tap water prior to gas nucleation tests is shown to remove sufficient amount of gas nuclei existing in the water, thereby drastically reducing the number of bubbles nucleated on bitumen. Enhancing gas nuclei formation in hot process water is identified as a promising strategy to improve bitumen-bubble attachment during oil sands conditioning, and hence to increase bitumen recovery from low grade ores.

Jan 1, 2014

By A. S. Chekmarev, T. Z. Lygina, K. G. Egorova, A. V. Skvorcov

"We have conducted analytical and technological evaluation of sepiolite containing clay. The possible areas of application of the sepiolite have been investigated and complex methods of enrichment of natural sepiolite have been identified. It was determined that for preserving the structure of minerals after processing the most effective method of the natural agglomerates disintegration was the soft abrasion of the clay fraction up to 0,5 mm. Disintegration of sepiolite clay along with using high energy-stressed effects on the matrix can deteriorate the rheological properties of clay suspensions and reduce the yield of drilling mud and sorption properties. To improve the quality of clay powders we used combined gravity-modifying method of wet enrichment. After the wet enrichment the yield of drilling mud increased up to 12.7 m3/t, with the addition of MgO up to 20,3 m3/t. It was noted that drilling muds contenting more than 50% of sepiolite are stable in mineralized (salt) waters. Based on the studied activated sepiolite rocks we obtained the effective heat-insulating materials with relatively low thermal conductivity – 0,165 W/m·K, average strength – 7,29 MPa and water absorption-49,0%.INTRODUCTION The modern development of the Russian economy requires the implementation of scientific and technical tasks. The solutions of it involves a radical reduction in energy, heat losses and material consumption of products, rational and efficient using of all types of resources, as well as the using of new types of mineral raw materials and materials based on it. An example of a new type of mineral raw materials for Russia is sepiolite containing rocks, due to unconventional conditions for their soils accumulation in the climate of the Far North. Sepiolite is a unique type of nonmetallic mineral. It is formed in soils, marine and saline basins, occurs in carbonate and carbonate-clay rocks in the form of lenses and lens – shaped layers, rarely nodules, loose powdery masses, shell-like concretions. Sepiolite may have a soft porous macroscopic appearance or less often the structure of the fibrous mass. Color of sepiolite is from white to cream with gray, green, pink and even crimson shade depending on the degree of pollution. Sepiolite can be in two forms - a-sepiolite (parasepiolite), which occurs in the form of large packets of crystalline fibers and ß-sepiolite, which occurs in the form of amorphous aggregates or small flat rounded particles. The sepiolite fibers have a length of from 0.2 to 2 Å, width from 100 to 300 Å, the thickness from 50 to 100 Å (Geological dictionary, 1973)."

Jan 1, 2018

By Ata Akcil, Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

Phosphorus slag is one of the most large-tonnage of yellow phosphorus production waste, which for decades stored in the slag disposal, by polluting the environment and creating environmental problems in the regions. Phosphorus slags from the processing of Karatau phosphorites are a very promising source of raw materials not only for silicon compounds but also rare earth metals (REM). Among the REM, yttrium, neodymium, europium and lutetium predominate, which are relevant to high-tech industries. The report presents technological scheme of complex processing of slags of phosphoric production with obtaining of REM concentrate and precipitated silicon dioxide ("white soot"). The regime parameters of the main operations of the technology are determined: I stage- leaching of slag with nitric acid solution; extraction of the REM-containing solution with tributyl phosphate and stripping of the REM with water; settling of solution of salts of oxalic acid, calcining the precipitate to obtain a concentrate S REM oxides and II stage of leaching silicon cake to obtain "white soot". Recovery of S REM from slags of phosphoric production on various redistribution has made, %: leaching – 95.0; extraction - 90.2; extraction on the average ~ 93.2; the production of a concentrate of REM oxide is 93.9. A concentrate containing 17.3 % of REM oxides was obtained. According to X-ray analysis it contains the following phases: calcium oxide, portlandite2, gadolinium oxide and yttrium, gadolinium oxide, gadolinium oxide and cerium, neodymium oxide, neodymium oxide and cerium. Thus, the concentrate can serve as a raw material for the production of individual rare-earth metals like gadolinium, cerium, yttrium and neodymium. After performing the II stage of leaching siliceous cake with nitric acid the samples of "white soot" were obtained. Its chemical composition corresponds to the state standard and has a specific surface area equal to 180 - 200 m2/g. The technology has been tested in a large-scale laboratory scale and will solve the problem of complex processing of phosphorus raw materials and import substitution in Kazakhstan. The end-to-end recovery of S REM oxides and silicon into concentrate and product from their initial content in slags is ~ 75.0 and 98.0 %, respectively.

Jan 1, 2018

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

By Yosep Han

Mechanically-induced chemical reactions between natural beach ilmenite (FeTiO3) and silicon (Si) have been examined by a combination of X-ray diffraction (XRD) and scanning electronic microscopy (SEM) analyses. The effect of various milling time on the phase transformation, crystallite size, and lattice strain of a beach sand ilmenite with silicon, and on their leaching behavior in hydrochloric acid (HCl) has been investigated. For mechanically activated FeTiO3, the crystallite size decreased and lattice strain increased monotonically with time of milling. However, the mechanochemically synthesized ilmenite with silicon showed a relatively smaller crystallite size and greater lattice strain compared with the mechanically activated ilmenite under the same milling condition. In accordance with the elapse of milling time, the intensity of both pure FeTiO3 and mechanically activated FeTiO3 gradually decreased. However, in case of the mechanochemically synthesized ilmenitereduction of FeTiO3 by silicon resulted in formation of rutile TiO2 at the milling time of 20 h and afterwards. Additional leaching experiments were carried out at an HCl/ilmenite (wt%) ratio of 20:1. The concentration of HCl was 3 M and the reaction temperature ranged from 70 to 90 oC. Mechanical activation was observed to significantly enhance the dissolution rates of both iron (Fe) and titanium (Ti) in HCl. Particularly, effects of both milling time and silicon addition on the dissolution rates of titanium and iron were significant, while those of temperature were relatively minor under the conditions investigated in this study. Keywords: mechanochemical treatment, natural beach ilmenite, silicon, leaching behavior

Sep 1, 2012

By A. Kogelbauer, A. Stadtschnitzer, A. Boehm, F. Schillab

"The paper covers the design and implementation of an industrial dense medium cyclone plant for carbonaceous iron ore, the proving of efficiency as well as the development of a predictive model for plant control. The VA Erzberg GmbH mines about 12 Mio.t of carbonaceous rock ore at the “Steirische Erzberg”. Due to increased demand of the Austrian steel plants, the production of ore concentrate was raised by 30 % up to 3.0 Mio t/a during the last 5 years. One of the projects to realize the increase in capacity at improved concentrate quality was the implementation of a dense medium cyclone plant for the fine size fraction – 8 +1 mm replacing the former dry permanent magnetic drum separators. By physical separation the siderite variety “spateisenstein” (42% Fe) of a density of 3,8 g/cm³ is separated from ankerite (10 – 17% Fe), the second iron bearing carbonate with a density of 3,2 g/cm³, dolomite, calcite and silicate bearing schists. The feasibility of the process was proven by the test results obtained from a test rig, that was constructed and operated in close cooperation between the Chair of Mineral Processing, Montanuniversitaet Leoben and VA Erzberg GmbH. The density separation surpassed the efficiency of magnetic separation clearly shown by •- values. The plant performance tests (capacity 120 t/h) verify the cut densities defined by Tromp T50 -values and the assigned efficiency found in the pilot tests at varied settings of media density, pressure drop, cone angle and apex diameter. The test rig as well as the final process will be presented. In order to create a tool to predict the performance of the DMS in the centrifugal field at various settings for varying feed composition the experimental results from size and density testing are analyzed in a modified way to obtain physically justified, smooth approximations for the performance curves. Models developed on coal washing plants are checked for their validity at increased densities."

Jan 1, 2018

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By Vasile Murariu, William Pate, John Herbst, Dilek Alkac

"Multiphysics models are essentially first principles models capable of providing very accurate micro scale predictions. The computational requirements for Multiphysics Models are extensive, precluding their direct use for flowsheet simulations. Population balance models get their form from theory but the model parameters have to be provided from experiments. The prediction errors for the population balance models are typically significantly higher than those for the Multiphysics Models but the computational effort for Population Balance Models is typically much less than that for the Multiphysics models. The hybrid model described here takes advantage of the strengths of each of the two primary model types and minimizing the weaknesses of each. The Multiphysics Model is used to perform high accuracy "experiments" that are difficult or impossible to conduct in laboratories or plants. The results of these experiments are combined with standard laboratory or plant data to parameterize and further enhance the Population Balance portion of the hybrid model. The creation of a useful Hybrid Model is demonstrated for a MP1000 secondary crusher. The validation of the hybrid crusher model is also presented. Finally the use of the Hybrid Model is illustrated in a full comminution flowsheet simulator."

Jan 1, 2014

By Q. Cui, Z. G. Song, S. S. Lin, S. Q. Li, S. S. Lu, G. B. Zheng, A. J. Ren

"Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization test studies on fluorite in tungsten beneficiation tailings and feldspar in molybdenum beneficiation tailings have been carried out by author and good test results are achieved. Some of the technologies developed in the test study have been applied in industrial productions, which have been working well. The economic, social and environmental benefits are remarkable. Our test studies and some production practices will be summarized and current situation and existing problems of comprehensive utilization for nonferrous metal mine tailings will also be discussed. Assumption and prospect for the future study on comprehensive utilization of nonferrous metal mine tailings will be brought at last.INTRODUCTION Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization of nonmetallic minerals of nonferrous metal mine tailings not only can improve the value of the ore but also reduce the stock of tailings, being the key to reduce emissions at source for exploitation of nonferrous mineral resources (Cai, Yang, 2000)."

Jan 1, 2018

By M. M. Kulkarni1

Kaolin clay is used as a filler and pigment in various applications such as paper, paint, rubber, plastics, adhesives, ink and ceramics etc. Major mineral content in crude kaolin clay is kaolinite along with some accessory minerals as quartz, hematite, mica, feldspar, anatase, rutile, illemnite etc. The Fe and Ti bearing minerals play very important role in determining quality of the kaolin, as these minerals impart yellow, pink or darker color to the white kaolin. Conventional beneficiation methods used in kaolin processing are de-gritting, classification and sodium dithionite bleaching, which improves the optical properties of kaolin, wherein reduction of color imparting constituents such as Fe2O3 and TiO2 is marginal. In the present study, these coloring impurities are separated using selective adsorption of water-soluble polymers. Degritted kaolin samples after passing through 45 micron sieve is used in the study for selective flocculation by polyacrylamide based polymers. The effect of pH, zeta potential, and polymer dose on the reduction of impurities is studied. Analytical tools such as XRF, XRD, SEM, and TEM techniques are utilized and results are discussed in detail.

Sep 1, 2012

By M. Z. He

Attractive particle interactions which underpin the sliming of gangue mineral particles onto valuable mineral phases are encountered in a number of flotation circuits. Sliming leads to poor flotation recovery of the valuable minerals and high recovery of the gangue particles in the concentrate. To mitigate sliming, low molecular weight poly-electrolytes are commonly used as dispersants during pulp conditioning prior to flotation separation of the valuable and gangue mineral phases. In the present work, the sliming mechanism of sericite onto chalcocite and the influence of interfacial chemistry and two anionic copolymer dispersants (carboxylate substituted polyacrylamide, polymer Cyquest 3223 and sulfonate substituted polymaleic acid, polymer P80) on the sliming interactions were probed in the pH range 5~9. It was shown that the sliming occurred under solution conditions where both chalcocite and sericite particles were negatively charged, as evidenced by their apparent particle zeta potentials. The suspension pH had a profound effect on sliming process as the extent was markedly greater at lower than higher pH. The sliming was found to be due to the chalcocite dissolution, Cu (I) release and oxidation to Cu (II), followed by hydrolysis and specific adsorption, leading to sericite particle surface charge reversal and the formation of electropositive sites on chalcocite surface in the pH range 5~9. Addition of polymer Cyquest 3223 or P80 not only increased the magnitude of zeta potentials of both sericite and chalcocite particles but also reduced the formation of Cu (II) ions and complexes, which mitigated the sliming behaviour. The adsorption of polymer Cyquest 3223 or P80 at 3 g polymer / kg solid or more had a significant impact on the zeta potentials of both sericite and chalcocite particles. Sericite-chalcocite particulate adsorption studies showed that sliming was completely suppressed via an electro-steric repulsion mechanism resulting from anionic polymeric dispersant adsorption at dosages > 3 g polymer / kg solid.

Jan 1, 2014

By T. Suzuki

Acid leach liquors from spent lithium-ion batteries employing lithium cobalt dioxide (LiCoO2) as a cathode active material contain valuable metals such as cobalt and lithium, as well as common metals such as aluminum and copper. The objective of this study was to develop a hydrometallurgical process providing a high selectively between aluminum, cobalt, copper, and lithium from hydrochloric acid solutions. Batch experiment results showed that selective hydroxide precipitation approach was not suitable because a significant amount of cobalt and lithium was co-precipitated with aluminum and copper hydroxides. In contrast, batch experiments and the subsequent data analysis indicated that the sequence of solvent extraction circuits using PC-88A, Acorga M5640, and tri-n-octylamine (TOA) extractants effectively separates four metals of interest. In the first circuit of the proposed process, copper was selectively extracted by Acorga M5640 at the pH 1.0-2.0. Aluminum, cobalt, and lithium remain in the aqueous phase. In the second circuit, aluminium is selectively extracted by PC-88A at pH 2.0-2.5. For the separation of remaining cobalt and lithium, Acorga M5640 provided higher separation efficiency compared to PC-88A single extractant and PC-88A/TOA mixed extractant. However, the stripping efficiency of cobalt from the Acorga M5640 organic phase was found to be low (less than 10 %). Therefore, PC-88A/TOA mixed extractant rather than Acorga M5640 is an advisable choice for the separation of cobalt and lithium. Keywords: spent lithium-ion secondary batteries, solvent extraction, lithium, cobalt

Sep 1, 2012

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores whereas oxidized molybdenum ores, being finely disseminated and difficult to process, have not been exploited and utilized effectively. In this article the beneficiation process of a molybdenum ore occurred in an oxidized ore zone was investigated in order to provide a new way for the development and utilization of the oxidized molybdenum ores in China. The molybdenum mineral in the ore was mainly wulfenite and the associated minerals included barite, limonite, quartz and small amount of cerusite. Limonite in the ore occurred in a crust and honeycomb-like colloidal state and composed the framework for the formation of the other minerals in the ore, which filled the pores in the framework. Wulfenite was mainly fine-grained and occurred in the fine porous crust and honeycomb-like framework. The finely disseminated ore structure made the separation and recovery of the molybdenum mineral in the ore very difficult. On the basis of the mineralogical study of the ore, experiments were conducted to compare the various mineral processing methods for the beneficiation of the ore, including single gravity concentration, single magnetic separation, single flotation, and a combination of high intensity magnetic separation and gravity concentration. The results indicated that with single gravity concentration a molybdenum concentrate containing 5.85 % Mo with a yield of 11.76 % and a Mo recovery of 43.5 % was produced. With single high intensity magnetic separation it was very hard to obtain a molybdenum concentrate product. With single flotation process a molybdenum concentrate containing 7.06 % Mo with a yield of 15.14 % and a Mo recovery of 62.63 % was produced. With a combination of high intensity magnetic separation and gravity concentration a molybdenum concentrate containing 6.46 % Mo with a yield of 11.81 % and a Mo recovery of 42.11 % was produced. In conclusion, compared to the other methods the flotation process can produce more reasonable technological and economical results and is the best process for the exploitation and utilization of the finely disseminated oxidized molybdenum ore.

Jan 1, 2014

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003