Search Documents

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003

By Grigory Voyloshnikov, Sergey Petrov, Vladimir Petrov

"The treatment of high-grade copper gold-bearing ores is practiced extensively. However, due to low concentration of copper the application of a separate process for copper recovery can make this process uneconomical. The copper, in particular: in oxide minerals, intensively bounds with cyanide during conventional cyanidation. In this case, cyanide is not able to react with precious metals and the consumption of cyanide increases. The resulting copper cyanide complexes have a negative effect on the recovery of gold. Due to decreasing of the process parameters, a repeated use of the recycled solutions can be hindered, especially in the case of heap leaching. The technology of copper removal from the process solutions with simultaneous regeneration of free cyanide from copper-cyanide complex and producing of a saleable high-grade copper concentrate was developed. An important feature of this technology is simplicity, the absence of complex or dangerous operations and the use of common reagents. The choice of equipment depends on the ore treatment option: heap or vat leaching. Also, simpler equipment schemes are available. The studies, tests and industrial practice show that if the concentration of copper can be decreased down to the first numbers of mg per ppm or lower, it is reasonable to maintain the process copper grade in the recycled solutions at 30-50 mg/L. In this case, recycling of cyanide-bearing solutions is unlimited. The regeneration of free cyanide from that of bound with copper and other cyanide complexes is 95-98%. The grade of copper in the concentrate is 55-60%. This technology is an economically competitive option, in particular: with the account of the sales of copper concentrate. The removal of copper has a positive effect on gold recovery, especially during heap leaching. In addition to, this offers significant benefits in reduced costs."

Jan 1, 2014

By G. A. Wierink

This paper discusses a new method to increase flotation recovery. As known from literature, fine and coarse particles have different flotation rate constants, hydrodynamic behaviour and require different reagent regimes. The device discussed allows separate processing of finer and coarser slurry by extraction of a third stream, carrying finer slurry, from the flotation cell. By separate treatment of fine and coarse slurry operational conditions and so flotation recovery for both may be optimized more efficiently. Extraction and classification of the third stream is accomplished by low speed centrifugation and Taylor-Couette flow separation. This Dual Outlet Device (DOD) can be installed in a traditional flotation cell without need for equipment replacement. In order to asses different design options for the DOD a transparent laboratory scale model was built. For this scale model Computational Fluid Dynamics (CFD) simulations using the RANS k-e and LES turbulence models were performed. Essential insight in the dominant flow systems relevant to optimal operation of the DOD was obtained from the CFD simulations and flow visualization tests with the laboratory scale model. Based on these findings a number of configurations were investigated at pilot plant scale in a 5 m3 Outokumpu flotation cell. The results of the pilot plant study show that utilization of the DOD provides a method for in-cell control over particle size distribution in the slurry. Use of the DOD in a flotation cell may enhance flotation recovery and decrease flotation reagent consumption significantly, against marginal investment and operation costs.

Jan 1, 2014

By A. P. Wang

Porous carbon adsorbents derived from inorganic materials templates such as zeolite and mesoporous silicate attracted considerable attention in the last decade and got great progress in re-cent years. However, so far almost all of templates used in the process were artificial porous materials; the porous carbons prepared by this method are very costly, which restricts the synthesis and application of templated porous carbons. In order to reduce the cost of templated porous carbons, natural inorganic porous minerals have been taken into consideration, which maybe possible and promising templates to prepare carbon adsorbents. In this work, we describe template process using tubular halloysite, rich mesoporous zeolite and low bulk density diatomite, as exemplars of the categories of inorganic porous templates which we have studied and discussed the effects of different templating structure on the resultant carbons. Two main carbon precursors, sucrose and furfuryl alcohol, were used respectively. The morphology of minerals and corresponding templated carbons were characterized using electron microscopy. The pore structures of minerals and templated carbons were characterised with nitrogen adsorption. The results showed that the morphology and pore structure of porous carbons are in good pertinence to those of corresponding templates. The morphology and pore structure of templated carbons could reflect those of corresponding templates at nanometer level. The templated carbons with high specific surface areas and rich mesopores can be prepared by using these three kinds of natural porous minerals as templates. The higher the surface area and pore volume of the minerals, the higher those of the corresponding carbons. The template carbons from halloysite possessed higher pore volume and mesoporosities. Based on the large mounts of experiment results, a model for the mechanism of resultant nanopores formation has been proposed. The nanopores of templated carbons are mainly composed of three kinds of pores: templated pores formed by removing mineral, hereditary pores formed by inheriting the pores of templates and nanopores formed during carbonization. These three kinds of pores have a close relationship with corresponding template.

Jan 1, 2014

By Z. K. Liu

Production of the amines collectors and cation surfactant gives out the liquid waste containing high COD (Chemical Oxygen Demand) and ammonium & nitrogen, which is difficult to be treated with conventional biological method to reach waste water discharge standard. In this paper an engineering practice of treatment on the liquid waste by the technology combined high effective microbe with A/O (Anaerobic& aerobic) process is presented. The quality of treated water comes up to class A national standard for discharging.

Jan 1, 2014

By K. Saberyan

In this study, solvent extraction of zirconium by using triphenylphosphine oxide as extractant has been investigated. The results showed that extraction of zirconium by triphenylphosphine oxides in nitric acid and hydrochloric acid media were negligible. Extraction of zirconium in acetic acid media with concentration of 0.01~0.2 M has been studied and the results showed that the maximum percent of zirconium extraction was 40% in acid acetic with concentration of 0.01 M. By addition complexing agents such as potassium thiocyanate with the concentration of 0.01~0.2 M zirconium extraction increased up to 86% in 0.2 M potassium thiocyanate. By addition of sodium salicylate with concentration of 0.01 M and in pH=2.5, the maximum extraction of 96% was achieved. The striping of zirconium from organic phase can be carried out by 0.5 M solution of sulfuric acid.

Jan 1, 2014

By Andrzej Luszczkiewicz, Tomasz Chmielewski, Jan Drzymala, Andrzej Konieczny, Rafal Kaleta

Properties of the sedimentary Polish copper ore mined from the Legnica-Glogow Copper Basin (SW Poland) by KGHM Polish Copper S.A. were presented and currently used beneficiation technologies were described. Due to a unique lithological layered structure of the polymetallic deposit and existing mining system, the ore currently processed in the three KGHM concentrators is very complex with variable content of the carbonate, sandstone and shale fractions. The mined copper ore contains from 0.8 to 1.8 % Cu and Ag, Pb, Zn, Ni, Co, V and Mo as accompanying metals. The paper presents difficulties in upgrading the LGOM ore and selected possible solutions and development concepts of its processing. The first one is a chemical treatment with controlled amount of sulfuric acid of special product of flotation such as for instance middlings. The acid treatment leads to increased liberation of copper minerals and better further processing. Another concept is atmospheric leaching in oxygenated sulfuric acid and ferric ions solution as the major unit operation applied to selected low grade final flotation concentrates or flotation by-products. The third approach, based on copper ore pre-flotation with a frother to partially remove Corg, is also considered.

Jan 1, 2014

By Zoran M. Stevic, Mirjana M. Rajcic-Vujasinovic, Zvonimir D. Stankovic

"Covellite is one of the most important copper sulfide minerals. Its behavior during the anodic polarization, as well as its rest potential in various solutions are of importance for flotation processes and also define the mechanism of electrochemical extraction of copper from sulfide minerals.Measurements of the rest potential have been performed in water solutions in presence of different cations and anions. The existence of the Nernst type dependence of the rest potential on the activity of some of the investigated ions was established. The biggest influence on the rest potential of covellite exhibits the change of activities of the ions forming the crystal lattice of investigated mineral, i.e. Cu(II) and S(II). The dependence of the rest potential of covellite on logarithm of Cu(II) activity has a shape of a strait line with a positive slope of 60 mV, while when concentration of S(II) anions increases ten times, the rest potential of covellite decreases about 120 mV. The first dependence was established in acid medium, while the second was registered in alkali one.Different electrochemical techniques have been used for the investigation of the behavior of covellite during anodic polarization. In the basis of all these measurements is a three electrode system consisted of: 1) working electrode made of the sample of natural covellite from the Bor mine (Eastern Serbia, Yugoslavia); 2) reference electrode (saturated calomel electrode) and 3) counter electrode (flat platinum). Electrolyte solutions used in these investigations are of the same kind as those used in the rest potential measurements. Sulfate and chloride solutions, as well as the mixed sulfate/chloride solutions, are the most perspective from the application point of view.Cyclic voltammetry has been the first used method that confirmed the formation of passive layer on the electrode surface during anodic polarization. Elementary data about the reaction mechanism have been obtained too. More detailed data needed for more precise conclusions about the mechanism and rate of the anodic process on covellite have been obtained by galvanostatic method. It was established that the essential difference exists between the reaction mechanism in sulfate and chloride solutions. Also, the difference is exhibited in the nature of reaction product directly connected with the passivation of the electrode surface. Chronopotentiometric investigations have been performed in sulfate, nitrate, chloride perchlorate and mixed sulfate/chloride solutions applying different current densities. The shape of obtained curves indicate if there was a surface passivation and how intensive it was."

Jan 1, 2003

By Arkady Senchenko

The paper deals with the problem of refractory gold-containing material processing. It is observed that all traditional methods for liberation of fine gold from this type of products are characterized by a number of essential disadvantages, where the main ones are ? considerable expenses for ore processing and big environmental impact. As an alternative to the existing methods there is considered a gold liberation method, which is based on the combination of ultra fine grinding process with the consequent atmospheric oxidation. The theoretical justification of atmospheric oxidation was carried out, in the result of this the mechanism and the degree of sulphide minerals? oxidation was found out, the dependence of gold dissolution speed on the slurry content in liquid phase produced by grinding and oxidation was identified. The experimental data and results of pilot-plant testing are given and the most effective grinding and atmospheric oxidation mode is selected on this basis. The performed complex of research works allowed us to use the provided technology at the gold processing plant having capacity of 8 mln. tons of ore per year. The questions, problems, advantages and disadvantages of atmospheric oxidation technology for refractory gold-containing concentrates are considered in this paper. Keywords: refractory gold-containing material processing, gold liberation method, cyanidation

Sep 1, 2012

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By D. B. Sundar Ramam

In the recent past, a paradigm shift in terms of resource utilization and beneficiation practices is experienced by the Indian mining and mineral sector. Depleting iron ore reserves coupled with increasing demand for low-alumina iron ore fines to improve blast furnace performance in terms of productivity and reduced slag rate necessitate intensive beneficiation of iron ore. The task is even difficult for Indian iron ores, which are generally high in iron content and at the same time characterized by aluminous gangue. In 2006, M/s Tata Steel commissioned a state-of-the-art Jigging Plant (Batac Jig) at Noamundi Iron Mine (NIM), mainly to reduce alumina in iron ore fines. The jigging plant is incorporated in the existing beneficiation circuit to treat ?10+0.5mm size fraction of classifier fines. Over the course of plant stabilization while the plant could deliver desired ore upgradation and average product alumina, variability in terms of alumina content has been a concern. This paper discusses a case study of process parameters optimization in jigging operation to achieve consistent product quality while improving the effectiveness of gravity concentration for the beneficiation of Noamundi iron ore also to take care of inferior plant feed (input) grade year on year. The operating variables used to optimize jigging operations include bed height, pulsion and suction time, particle size, strokes, and plant throughput rate.

Sep 1, 2012

By Chuanyao Sun, Longli Liu, Fayu He, Guiye Wu

Utilizing thioglycolic acid (TGA) as a template and using structure-guided design, a molecular modelling approach has been used to design and screen appropriate dispersant for chalcopyrite. A series of organic dispersants based on a TGA substitution with hydroxyl and amino and sulfonic functional groups have been examined on chalcopyrite surface. 20 organic depressors of chalcopyrite have been investigated to study the quantitative structure-activity relationship (QSAR) of chalcopyrite depressors. For the chalcopyrite surface, depressor containing carboxyl and sulfonic group is generally stronger than the depressor containing hydroxyl group. Increasing the number of hydrophilic group can effectively enhance the inhibition. Increasing the number of Solidophilic group does not necessarily lead to enhanced inhibition ability; steric factor is one of the important factors to affect the interaction. Extension alkyl carbon chain length cannot enhance the interaction of depressors. Isomers principle as well as applies to the chalcopyrite depressor molecular design. Flotation verification tests further confirmes the accuracy of the molecular simulation. Through the Computer Aided Molecular Design (CAMD) technology, we can save enormous time and resources to design novel surfactants. This research and application will play a great significance role in sulfide flotation.

Jan 1, 2014

By C. Raghu Kumar

Hydraulic or teetered bed separators (TBS) are finding new avenues for application in the field of mineral processing. Floatex Density Separator (FDS) is a hydraulic/teetered bed separator capable of operating at high tonnage due to its advanced instrumentation. FDS/TBS is being used in Indian mineral sand industry for classification and segregation of different minerals. The purpose of this paper is to provide details on the performance of the plant scale FDS in recovering the chromite from feed (below 1mm size). Historically this feed has been processed using hydrocyclones and spiral classifiers; however, there is a strong trend now to employ teetered bed separators, thus allowing significant changes to be made in the plant for improving process efficiency. In the present work, the performance of the plant scale FDS is described in terms of partition curve (yield, cut size, classification efficiency/Ep) for different combination of process variables and also in terms of metallurgical grade and recovery. It is found that, efficient classification can be achieved at a maximum cut size of 380 µm with and the imperfection is also reported as low as 0.16. The grade of the underflow product is enriched as maximum as 52.2% Cr2O3 from a feed assaying 40.4% Cr2O3.

Sep 1, 2012

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By Jiongtian Liu, Guixia Fan, Caom Yijun

A cyclonic-static micro bubble flotation column (FCSMC) is an effective separation device for fine grain treatment. The separation of fine ilmenite by FCSMC was explored in this work. The influence of reagents dosage (regulator, collector and auxiliary collector), pulp density, circulation pressure and aeration quantity on TiO2grade and recovery wasinvestigated.The optimal conditions of a rougher are follows: pulp density 45%, pH 5.0, MOH collector dosage 2800 g/t, diesel oil dosage 700 g/t, circulationpressure 0.19 MPa, aeration quantity 0.8 m3/(m2•min). The optimal conditions of a cleaner are follows: pH 4.0, circulation pressures 0.16 MPa, and aeration quantity 0.5 m3/(m2•min).A pilot plant continuous test with a rougher-cleaner by FCSMC for 72 hours was proceeded under the optimum conditions. Compared with industrial flotation machines, the concentrate grade of FCSMC is 48.11% with an improvement of 1.08 percentagepoints, while the recovery is 82.36% with 13.64 percentagepoints increment. Moreover, the flowsheet is simplified from six parts (a rougher-two scavenger-three cleaner) in flotation machines to two parts (a rougher-cleaner) in FCSMC. Proofs were also provided by the analysis of the by-size grade and recovery of concentrate.Results show the FCSMC is an effective separation device to recover -74 µm size fraction.

Jan 1, 2014

By M. Marinov

The Bulgarian deposits of quartz-kaolin raw materials are localized in the NE Bulgaria. For many years, the quartz-kaolin sand separation has been performing by water washing technology. After wet separation the raw material yields two products ? washed kaolin (different grades) and quartz sand (different grades). Research and development program has started to improve the quartz-kaolin sand separation. The program has undertaken an increasing of processing capacity, to decrease the losses in the tailings and to provide production of new quartz sand grades. The kaolin-silica raw materials from Vetovo open mine and the technological tailings from Vetovo processing plant were characterized. It was established that there are a lot of losses of quartz in final tailings. New approach on kaolin-silica raw material separation was tested in laboratory scale. The test work was performed on Derrick Stacksizer screening machines. The results of laboratory experiment show that there are possibilities to increase the quartz sand recovery and to start the production new grade sand. The full-scale pilot test was performed including the following units: two Derrick Stacksizer screening machines equipped with 0.430 mm and 0.150 mm opening Derrick Urethane Panel, respectively; Flat bottom DN 500 Hydrocyclone and DN 100 Hydrocyclon. The pilot test data clearly demonstrate that the Derrick Stacksizer screening machines are suitable for Bulgarian silica-kaolin raw material. Based on the test data a new quartz-kaolin separation technology was developed. The new technology was introduced in Vetovo processing plant increasing processing capacity and decreasing the losses of quartz in final tailings. Additionally the production of silica sand grade PK 0.16 is increased and starts the production a new grade PK 0.10.

Sep 1, 2012

By P. Khattri

At Tata Steel, Coal is washed in gravity and froth flotation circuit at 13-15 mm size and below. Being coal is high in ash (~35%) and difficult washability characteristics (having high (~40 %) NGM at desired ash levels) needs more and timely quality data of ROM for effective optimization and process control. Conventional approach of supplying quality data takes 4-5 hours time. This means during this period, it is assumed that coal is having similar characteristics as of previous set and it is not possible to fine tune during this time which resulted in yield loss. Hence producing clean coal on agreed ash value consistently is a challenging task because of high NGM and variation in input quality. To overcome the problem of collection of representative sample and timely result a new technology was adopted Prompt Gamma Neutron Activation Analysis (PGNAA) technology which is basically an online analyser using Gamma rays as the source to measure the ash content in coal running on a conveyor which gives real time ash analysis. The details of this technological intervention are discussed in details in this paper. Keywords: near gravity material, PGNAA

Sep 1, 2012

By L. Stamenov, H. Bouzahzah, S. Gaydardzhiev, D. Naumov

"The Chelopech epithermal arsenic bearing high-sulphidation, copper-gold deposit located in Bulgaria is often referred as the richest European gold deposit currently under exploitation. Key points from the flotation circuit of the processing plant have been sampled and selected physicochemical parameters measured. Plant survey has followed with selected samples being submitted to chemical and mineral liberation analysis (MLA). Quantitative analysis has enabled to link the flotation response of the main copper bearing minerals with the physiochemical parameters (Eh, DO, EDTA extractable Cu and Fe) being measured. Data from mineral liberation analysis have highlighted an important process-relevant information explaining the variable floatability in the various granulometric classes.The low chalcopyrite recovery could be linked to the non-sufficient amount of dissolved oxygen measured in the copper selective flotation circuit. Given the finely-disseminated copper bearing minerals, the observed copper losses inside the flotation could be also explained by the insufficient degree of liberation of the mineral grains. Suggestions for improvement in metallurgical recovery are therefore proposed.INTRODUCTIONThe Chelopech deposit is a high sulphidation (HS) volcanic-hosted epithermal gold-copper one (Bonev et al., 2002; Kouzmanov et al, 2009; Strashimirov, et al. 2002). It is considered as one of the largest and economically most important ore deposits in Bulgaria, and often is referred to Europe’s largest currently mined gold resource. It is located in the Srednogorie zone which falls within the central sector of the extensive Tethyan–Eurasian copper belt formed during Mesozoic–Cenozoic time along the southern margin of Eurasia. The Srednogorie zone has the features of a subduction-related, Late Cretaceous island arc, with development of a calk-alkaline to sub-alkaline volcano-plutonic magmatism and associated hydrothermal ore deposits (Bonev et al., 2002).Ore mineralisation occurs as veins, mineralised breccia, and massive sulphide replacements and disseminations. Three mineralisation stages have been identified at Chelopech deposit. An early pyrite–marcasite mineralisation (stage I), characterised by disseminated to massive pyrite followed and partly brecciated by enargite– luzonite and tennantite–chalcopyrite–bornite (stage II) mineralisation. The gold is met in ores belonging to the stage II. Sphalerite and galena veins characterise stage III, best developed below and adjacent to the pyrite–enargite– chalcopyrite ore bodies. Advanced argillic altered volcanoclastic rocks commonly host this mineralisation (Chambefort and R. Moritz, 2014)."

Jan 1, 2018