Search Documents

By Clifford Taylor, Alexander Zöhrer

"The execution of deep basement excavations under narrow conditions is one of the most challenging tasks in geotechnics. The vicinity of neighbouring buildings, roads, and underground structures such as sewers or power lines, quite often prohibits the application of standard solutions. In addition, legal considerations in the use of adjacent properties is becoming increasingly difficult. This paper will present some innovative approaches to overcome the above-mentioned challenges based on several case studies from central Europe. For every project the design approach as well as the techniques used for execution will be explained, detailing both the advantages and the limitations of the applications. One case study shows a deep basement excavation (approx. 17m) in the centre of Prague, Czech Republic. This project featured many challenging boundary conditions (narrow construction area, high ground water table, jet grouting column embedment into bedrock, constraints regarding use of ground anchors due to property rights, etc). The realisation of the complex design is described and illustrated in detail. Other case studies will show the combined application of bored piles with jet grouting and also explain the design of vertical prestressed anchors for retaining walls.INTRODUCTIONThe development of urban areas has always presented challenges, from access for equipment and materials to the rectification of existing foundations in unknown condition. Compounding these is the increasingly stringent requirements to retain, maintain and reduce impact on culturally and historically significant structures. As available space is becoming more limited, optimisation of real estate has resulted in buildings getting higher and their basements deeper below ground. Two or more basement levels are quite common, with typical excavation depths ranging from 5 to more than 10m. Additionally, we are faced with neighbouring buildings that are equally high, deep and massive. These buildings directly adjacent the retaining structure require underpinning to limit settlement, and in cases where they are within just a few meters, this building mass generates additional earth pressure for the retaining wall to support, resulting in complex loading cases.This paper highlights several common challenges and explores the measures implemented to overcome them. The challenges and examples of either design based solutions or practical applications will focus on the following topics – the limitations of conventional geotechnical construction methods, overcoming challenging geology and the requirement for watertight basement constructions."

Jan 1, 1900

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By Sanjay Gupta, Sorabh Gupta, Ravi Sundaram

A geotechnical forensic evaluation of piles for an industrial facility in Haryana was performed to assess the quality of the piles and to evaluate piles installed using two different types of rigs. Low strain pile integrity tests were performed on all piles to assess the pile length and possible presence of structural defects. Coring was done through questionable piles for the clinching evidence of concrete quality and pile length. Probe holes adjoining piles helped confirm the bulging of piles at shallow depth. The paper highlights the importance of implementing a well-planned quality assurance program to confirm that all piles installed are of the desired quality.

Sep 1, 2022

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By David P. Sauls

Design-build contract delivery provides unique opportunities for efficiencies in pile foundation design and installation. The Louisiana Department of Transportation and Development (LADOTD) US Highway 90 at Louisiana State Highway 85 (US90/LA85) intersection was contracted under the design-build delivery system, in part to take advantage of these efficiencies. As one of five projects recognized by the Design Build Institute of America (DBIA) when it honored LADOTD as its 2011 Transportation Owner of the Year in the highway/bridges category, the design-build method provided a way for this project to be ?shovel-ready?, which enabled the LADOTD to secure American Recovery and Reinvestment Act (ARRA) funding. This paper describes the benefits this project gleaned from the design-build process, which included synergy, schedule, design and construction efficiencies, and team building. Interlaced with design and construction of precast prestressed concrete (PPC) piling in compressible southern Louisiana soils, the design-build process rapidly translated computations to cost and schedule savings. A robust quality assurance program using Pile Driving Analyzer (PDA) equipment to evaluate pile set-up provided expedited acceptance of bridge bents and advanced construction schedule. Data evaluation includes analyses of PDA data obtained from 1-hour, 24-hour, 7-day, 14-day and 6-month restrikes of the project test pile.

By Annika Gram, Teddy Johansson, Lutfi Ay

Micropiles transfer tension or compression forces as well as cyclic loads into the ground via skin friction. The Self Drilling Micropiles (SDM) can be utilized for permanent applications. The hollow bar simultaneously acts, as drilling rod, injection tube and reinforcement for the micropile. The SDM system can be used in any type of soil, including unstable soils, without the need for temporary casing. Injecting a cement grout through the hollow steel tendon ensures that the borehole is filled from the bottom to the top. The system is fast, simple, and flexible. The installation minimises noise, vibration, and spoil. There are many potential applications, including foundations, underpinning, resisting uplift, dynamic/cyclic load applications and geothermal installations. The SDM technology were introduced to India first time in the Indian history and utilised in the 4G and 5G network projects. The SDM challenge the traditional cast-in-situ piles in the 4G project and raft foundations in the 5G project. Utilisations of the tensile and the compressive strength capacity of SDM with smart solutions results in noticeably big costs, 17-38 % depending on the soil conditions and time savings. The cost of the SDM solutions was about 40% less than the cast-in-situ piles and raft foundations in an ongoing 5G project. The SDM were used successfully in the liquefiable soil types as well.

Nov 1, 2022

By Peter Faust, Peter Hubbard, Kenichi Soga

The European Federation of Foundation Contractors (EFFC) and The Deep Foundations Institute (DFI) have set up a task group to compile a Guide for Working Platforms. The first edition of this Guide has been published in January 2020. The aim of the Guide is to provide reliable methods for design, testing and verification of working platforms for construction equipment, especially in the deep foundation industry where track loads can be excessive due to the nature of its operations. The Guide has identified areas where knowledge is limited. Actual track pressure and its distribution along the length of the tracks is still not well researched. Current recommendation provided in EN 16228-1 are believed to be overly simplified and may lead to conservative requirements for working platform thickness. This paper presents results of a series of field tests where the actual track pressure of a large drilling rig during operation was measured in real time together with the deformation of the working platform. Embedded, distributed fiber optic sensing (DFOS) at different depths throughout the platform allowed for a three-dimensional evaluation of the platform deformation throughout the entire operation. Results will help to develop more reliable recommendations for future safety requirements of working platforms for deep foundation equipment.

May 1, 2022

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By Justin Lukens, Di Stasim Jeffrey, Frank Di Salvo

Columbia University’s Manhattanville Campus expansion includes the construction of two new business school buildings. The new buildings require development of an entire city block bound by 12th Avenue, W 131st Street, W 130th Street and Broadway in Upper Manhattan. A support of excavation (SOE) package was first released, followed by a foundation package. The SOE package consisted of approximately 100 soldier piles and 280 anchors, up to 215’ long, to support a cut anywhere from 30’- 50’ below street level. The foundation package alone included approximately 1600 drilled micropiles. Given the breadth of the work scope, Hayward Baker Inc and Moretrench joint ventured on these two projects to bring sufficient knowledge and work resources to complete the work in an efficient and timely manner. This included working with the Owner/Engineer to propose different means and methods for construction to significantly reduce the schedule while meeting the design intent, such as large diameter (36” diameter) augercast piles in place of conventionally drilled soldier piles and large hollow-bar micropiles (103/51 bars) in lieu of pressure-grouted micropiles. The anchors, ranging from 3 to 22 strands, were used for earth retention through both soldier pile and lagging walls and existing slurry walls. These anchors were complicated based not only on their size and length, but also the need to drill some of them under the historic Studebaker building. The overall magnitude of the project with considerations to resource management and material lead times will be addressed, highlighting critical strengths provided by the Contractor to ensure project success. The scope of work discussed in this paper was executed under two separate competitive bid contracts. The first contract included the support of excavation work and the second contract included the foundation package. The support of excavation comprised of drilled soldier piles (performed by Case Foundation as a subcontractor to the JV), driven soldier piles, driven sheet piles, hollow bar tiebacks, multi-strand tieback anchors and micropile soldier piles. The foundation package consisted of drilled micropiles. Due to the large scope of work and critical schedule requirements of the project, the JV had to think outside the box and present value engineered alternates to expedite installation durations.

Jan 1, 2019

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By Matthias Pulsfort, Hanna Nissen, Markus Herten

An insufficient integrity of cast in-situ bored piles can lead to a reduction of the load bearing capacity and may require cost intensive repairs. Reasons for an insufficient pile integrity are linked to the construction process, mainly to poor concrete quality leading to bleeding and segregation of the fresh concrete. Moreover, the entrapment of soil and an insufficient concrete cover can pose a problem. Knowledge about the time-dependent development of the fresh concrete pressure during the construction process of bored piles is needed for a better understanding of the underlying processes causing these defects. Therefore, pressure measurements were carried out on different construction sites with pressure cells being installed at different depths along the reinforcement cage. The measurements revealed the maximum pressure acting on the surrounding soil. The achievement is a better understanding of the effects of the concrete placement specifically and the construction process in general on the surrounding soil to reduce the risk of pile imperfections.

Sep 8, 2021

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By Braxton P. Erbe, Douglas C. Brunot

A variety of systems and techniques exist to support deep excavations where sloping is not feasible. This paper will explore an example project involving the use of pre-engineered hydraulic bracing systems to support sheet pile walls. Challenges on site that drove the final design include a high water table, irregular excavation geometry, and underground obstructions. The hydraulic system, connected by pins and not requiring welds, allowed for quick deployment and the modularity to change as required due to unforeseen site conditions.

By Achyut Kumar Allady, Praveen Arumughan

NCHRP Synthesis 418 (2011) entitled, “Developing Production Pile Driving Criteria from Test Pile Data” details the occurrence of dichotomy between pile Skin resistance and pile Tip resistance mobilizations at different times for different hammer blows during pile driving operations. With increasing usage of High Strain Dynamic Testing (HSDT) the engineering community started paying more attention to this occurrence of dichotomy resulting in overdriving, pile damage, increased claims, and loss of time. To overcome the dichotomy limitations of HSDT, NCHRP recommends, “the use of superposition to combine the back-calculated tip resistance from a blow on initial drive or from redrive with the back-calculated skin resistance from the early blows at the beginning of restrike”. However, the current practice of external mounted gauges and signal matching for a single blow are unable to evaluate independently the Skin resistance and Tip resistance to achieve the goal of determining the optimum Total Pile Capacity using the superposition. This paper discusses advancements of science and technology with sensors embedded at the pile top and pile tip, the data collected is analyzed by the state-of-the-art FDOT Method to determine Skin and Tip resistances independently for every blow. Independent Tip and Skin resistances each with a Resistance Factor can be summed up to obtain optimum Total Pile Capacity. Additional benefits of determining independent Skin and Tip resistances include obtaining lost skin capacity due to scour, due to pre-drilling/preforming and uplift tension capacity. Furthermore, the benefits of embedded sensors include increased quality control/quality assurance through 100% testing, accelerated construction, life cycle monitoring and asset management.

May 1, 2022

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By Ramanathan C, Prasad P. V. S. R

The most critical challenge for any large size storage structures to be constructed on soft compressible soils is bearing capacity and consolidation settlements. Consolidation is the time dependent phenomena, as expulsion of water from soil voids on application of external load will take longer period. It is mainly influenced by soil consistency, permeability, thickness of compressible stratum and presence of free draining layers. This study deals with the foundation solution of a large size Mounded Storage Vessel (MSV) to be constructed on thick compressible stratum whose loading intensity is around 155 kPa and the estimated settlements are greater than 400 mm. Hence, the foundation solution using vibro stone columns is adopted as an effective technique to address the challenges of excess settlements and inadequate bearing capacity. Further to keep settlements within the permissible limit of 50 mm, preloading technique with 60% of actual loading intensity will be utilized. The consolidation analysis of stone column reinforced foundations is carried based on the method given by Han and Ye (2001). The quality of the stone columns is ensured by real time quality control measures and the performance of the stone columns shall be ensured by vertical load tests. Ground settlements was closely monitored with proper instrumentations and the actual degree of consolidation has been verified by Asaoka’s (1978) method.

Sep 1, 2022

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015