Search Documents

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By Patrick P. A. Wolfs

In the summer of 2000, the ECR®/EFT® was first introduced in the Netherlands. After the first project a field test was performed together with other geophysical methods to prove the liability of these systems and their application in areas with soft soil and high groundwater levels. The objective of this test, which was carried out with three leakage detection systems, was to locate the holes. After this test several projects have been carried out. In this article the Dutch projects "Ringvaart Aqueduct" and "Bottleneck Limburg N296/N297" are mentioned.

Jan 1, 2006

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By Emad Farouz

The resistance of very dense glacial outwash formations consisting of sand, gravel and cobble formations can be quite high, and techniques for measuring the strength and deformation properties often cause engineers to underestimate the strength of these layers in drilled shaft design. More realistic measurements of this dense formation can be achieved with slotted steel casing pressuremeter tests. To minimize disturbance and achieve accurate measurements, drilling a pilot hole prior to probe insertion is necessary. Characterizing geologic formations that contain significant amounts of gravel and cobbles is challenging because of scale factor. Inserting a standard pressuremeter probe into this formation without damaging the membrane is difficult. This paper presents a case study for the IR-75 project in Dayton, Ohio, USA, where these dense materials were characterized using a slotted casing pressuremeter, optimizing design by providing more realistic properties of these materials.

Jan 1, 2006

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By Miklós Kovács

A new type of the cast in situ piles is introduced. The installation of the new pile is based on a pushing in/gaining back procedure. A temporarily closed tip element with square shaped cross-section being attached to an upper circular shaft tube is vibrated into the soil. The steel armature is embedded. Concrete is poured into the tube and, the whole structure is gained back while the tip is in opened position. The width of the tip is less than or equal to 40 cm. The maximum length of the pile is about of 14 m. Great bearing capacity is resulted from the double soil compaction effect. No spoil is generated and, the pile construction can be controlled. The paper presents the results of four loading test at three sites with some soil data.

Jan 1, 2002

By Wei Zheng

A pulverized coal fired power plant is being built in Osceola, Arkansas, along the Mississippi River. The subsurface soil conditions consist of a certain amount of very soft clayey silt and clay underlain with a medium dense sand layer and a dense sand layer. The site has been raised four to five feet with fill material consisting of sand and gravel. Consolidation settlement due to the fill is expected to cause negative shaft resistance (downdrag) on the pile foundations. The site is located in a high seismic hazard area - the New Madrid Seismic Zone (NMSZ). The liquefaction analyses indicated that there is a high liquefaction potential in the medium dense sand layer. Load tests are needed to determine the shaft resistance and the end bearing of each soil layer for design purpose. Two types of pile foundations ? augered pressure grouted displacement pile (APGD) and partial augered pressure grouted displacement pile (P-APGD) were considered for this project. Ten pile load tests, including five compression tests and five tension tests, were performed for three different areas. Strain gauges were installed for the compression tests. The APGD and P-APGD piles were installed side by side for comparison. In addition, three additional dynamic tests were performed to supplement the information from the static load tests. Load deflection curves for the compression tests were predicted, and the failure loads were interpreted using four different methods. The shaft resistance and the end bearing were determined from the strain gauge data and were used to back calculate the ultimate capacity. The back-calculated capacities are in good agreement with the predicted failure loads; they were further verified with the tension load test results.

Jan 1, 2007

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70's. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

Jan 1, 1984

By Maurice Guillaud

The most striking innovations on diaphragm-wall construction plant are those associated with continuous real-time trajectory monitoring of the excavating tool (either a grab or a hydro-cutter). The recent equipments are fitted with clinometers and gyrometers to control deflection, rotation or deviation from the vertical, thus allowing to install diaphragm-walls with a verticality accuracy of less than 0.3%. One of the greatest advantages of extensive use of on-board IT systems on the Hydrocutters and hydraulic grab machines is that it aids quality control by automatically producing complete real-time reports of all excavating data (verticality, depth, type of ground, rate of progress, stoppages, etc.). These reports are available to the Engineer, providing the total transparency required for Works Supervision and the Quality Assurance Plan. They also provide the Contractor with input data for databases used for optimising efficiency and progress criteria on future jobs.

Jan 1, 2002

By K. [Muthukkumaran

An extensive program of laboratory model tests was undertaken to study the effect of slope on p-y curves under passive loading in dry sand. The paper concerns the method developed in a series of laboratory model tests to experimentally determine p-y curves. Bending moment curves are differentiated by using curve fitting method of cubic polynomial function. The study includes effect of slope angle and relative density on bending moment and non-dimensional p-y curves. The non-dimensional p-y curves for piles on sloping ground under passive load are developed modifying API method by including a Reduction Factor (R) using the experimental results.

Jan 1, 2006