Search Documents

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By D. A. Bruce

To check the feasibility and the quality of a very deep diaphragm wall, a tern of adjacent panels has been constructed, up to a depth of 100 m, in the Milan sandy gravelly soil by means of a hydraulically driven milling machine with reverse circulation of mud. The results of the monitoring carried out in order to evaluate the panel geometry and the quality of both joints and concrete are described. The use of instrumentation based on different physical principles allowed the cross checking of measurements as well as the evaluation of the accuracy and sensitivity of each single procedure to be performed. The trial field was successfully carried out and the feasibility of a diaphragm wall of such a depth was demonstrated and corroborated by a reasonable level of quality control.

Jan 1, 1989

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Geoffrey C. Hebner

Augered, cast-in-place piles (ACIP) have become a very common foundation type in Atlanta and the Southern Piedmont Province as well as much of the United States in the past 20 years. Prior to the introduction of ACIP foundations in Atlanta, the most common deep foundation type was Raymond piles. Raymond piles are basically a driven, thin-walled step-tapered steel pile filled with concrete. Drilled piers were also relatively common and continue to be used, particularly in shallow bedrock or high column load situations. Driven piles, including pipes, H-sections, and timber piles were previously common with working loads typically in the 30 to 50-ton range. Initially, ACIP foundations had similar allowable capacities, however, over time improvements in installation techniques and equipment have resulted in an increase in allowable ACIP capacities. Correspondingly, they have become a more cost-effective and trusted foundation for geotechnical and structural engineers. Over the next several decades many other deep foundation alternatives began to lose popularity. ACIP are one of the predominant deep foundations in Atlanta and the Southern Piedmont today. Although ACIP foundations have widespread popularity in the private sector, they have not been readily accepted currently by government transportation agencies. ACIP may be used by some of the smaller municipalities, but to the author's knowledge, have not been used with regularity by larger, state agencies.

Jan 1, 2003

By F. H. Chen

the Rocky Mountain Region since 1950, drilled pier foundations have been widely used to combat structural movement problems in expansive soils. It is now an accepted practice for engineers to use drilled pier foundations in expansive soil areas. Piers are generally drilled into bedrock in a zone unaffected by moisture change. With some exceptions, such system has successfully prevented damage incurred in the structures as the result of soil expansion. In the last 15 years, no significant advancement has taken place in the design of the drilled pier system on expansive soils. Numerous failures continued to be reported. Causes for the failures were placed on poor drainage, inadequate void under the grade beams or mushrooms on top of the piers. Engineers realize that these are certainly not the major problems. The basic design criteria should be critically reviewed. It is the purpose of this paper to point out the actual problems confronted by designers, the failure module and remedial measures, The writer does not claim to have the solutions. In fact, it will be a long time before real solutions can be found, yet the writer believes the engineering communities, the construction industry and the general public should be aware of the true picture of the problem.

Jan 1, 2010

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

Jan 1, 2002

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations. The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works. This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By B. H. Moore

Foundation and excavation problems associated with lock construction projects vary widely. Each lock requires a different foundation to respond to a unique geologic setting. The range of heights and founding materials are illustrated thru description of selected structures encountered in the United States. Examples range from 113-ft high John Day Lock on the Columbia River founded on basalt rock to the 17-ft high Lock No. 5 on the Arkansas River floated on a clay foundation. A description of the basic elements of design and construction is presented. Several case histories involving lock design and construction are assessed to aid in recognition of potential problem areas on forthcoming construction. In the past decade there have been many improvements in construction materials and techniques. The application of these new approaches to lock construction is discussed.

Jan 1, 2010

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001