Search Documents

By Robert E. McIvor

"The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill’s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “circuit classification system efficiency” (or CSE, McIvor, 1988a), and ultimately the discovery of the Functional Performance Equation (McIvor, 1988b, and McIvor et al, 1992). The CSE is the percentage of “coarse” (typically with reference to the plus P80) size material occupying the mill (versus “fines” or product size material, finer than the circuit P80), and can be calculated by taking the average of the percentage of coarse material in the mill feed and mill discharge. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, which is derived as follows.We define “fines” as any product size material, and “coarse” as that targeted to be further ground, the two typically differentiated by the circuit target P80. For any grinding circuit, the production rate of new, product size material (fines) must equal the specific grinding rate of the coarse material (i.e. fine product generated per unit of energy applied to the coarse material) times the power applied to the coarse material."

Jan 1, 2009

By Shahé Shnorhokian

A study was conducted on the seismic activities and associated rockburst events that took place at an underground Canadian metal mine over a period of five years. In the first stage, a back analysis of the microseismic database led to the identification of clusters of major events. The locations of these clusters were identified with respect to the local geology and the planned mining sequence. In the second stage, a numerical model was constructed using the finite difference code FLAC3D to simulate the in-situ stress, mine geometry, local geology, and stope sequence. Mining-induced stress fields were compared against two rockburst events that took place during this period, as well as against the various geologic units present. It was shown that by combining microseismic analysis and numerical modeling, it was possible to provide a basis for evaluating the influence of the in-situ stress regimes and stope sequencing on mining-induced seismic response.

May 1, 2011

By J. J. Bouillon

"Located in the northwestern portion of the Abitibi greenstone belt, Les Mines Selbaie is a copper-zinc (silver and gold) producer. Felsic tuffs host three are zones. Composed of sulphide veins and breccias, they are not exhalative massive sulphide deposits, except, probably, for the massive pyrite (fragments and lenses) localized close to the top of the volcanic sequence.The total of all (mineable and mined) ore in the three zones presently outlined on the property, is of the order of 29.9 x 106 tonnes with average grade of 0.63 g/t Au, 37.02 g/t Ag, 1.21% Cu, 1.91% Zn.The ore reserve calculations and the daily production procedures are computerized to various degrees. The data handling process is highly computerized.Various geophysical methods are, and have in the past, been successfully used on the property. The ""mise-à-la-masse"" surveys were used to perform the geological interpretation of an underground deposit (A-2 zone). Presently the PULSE-EM surveys are performed in all surface and underground exploration drill holes."

Jan 1, 1990

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

By M. W. Lewis

A mine's inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine ’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By M. W. Lewis, B. Sambirsky, J. Werner

A mine’s inherent capacity is dictated by factors such as equipment, design, people, processes, and environment. Actual production may approach, but never surpass, the inherent capacity limit. The inherent capacity ceiling can only be increased through re-engineering. Autonomous haulage systems have the potential to significantly increase a mine’s inherent and realized capacity. Realized capacity may be maximized through the optimization of soft factors such as the processes, behaviours, and organizational systems, controlling asset utilization, availability, and performance. Truck shovel dispatching systems revolutionized the utilization of mobile assets. High-precision global positioning systems (HP-GPS) are increasingly being adopted to optimize equipment performance. Real-time maintenance management systems have the potential to revolutionize equipment availability and significantly reduce cash costs. This paper explores some of the solutions available to mines to increase their inherent capacity and maximize their realized capacity.

Jan 1, 2004

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

"WELCOME/BIENVENUE TO THE COM 2014 IN BEAUTIFUL VANCOUVER!On behalf of the organizing committee, I would like to extend my thanks to you for participating in this year’s Conference of Metallurgists. Recent times have been extremely difficult for the resource sector, but it is crucial for our industry to maintain personal connections through good and bad times. These interactions include technical exchanges, and this is at the heart of MetSoc’s service to its members. The theme of this 53rd Conference of Metallurgists is Prosperity Through Process Advancements. There are thirteen symposia at this year’s conference mainly focused on processing from extractive fields, to materials and the environment. Supporting these topics are the plenary, poster session, and trade show plus opportunities for socializing at functions like the opening reception and the awards banquet.Many people have contributed to this conference, from the authors and presenters to the organizers and the generous sponsors. They are all gratefully acknowledged for their quality work over the last two years. A particular thank you to our student volunteers whom we hope will take advantage of their time at COM to network and to learn about this exciting industry.Again, thank you for being a part of this exciting conference of metallurgists. I hope it will be a memorable experience and that you are able to take advantage of all the conference and Vancouver have to offer."

Jan 1, 2014

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By The Staff

WE were requested to make a digest of our original grinding report, Fine Grinding Investigations at Lake Shore Mines. This digest is much easier to read than the original report, but it lacks the experimental 'evidence' found in the first report which, in many cases, is much more interesting and educational than the conclusions derived from it. In the course of rewriting the paper, we noticed several new angles on the test data which had not occurred to us previously. From the data included in the report and other tests not published, calculations were made which indicated a line of new test work. These tests, among other things, more than suggest a technique for designing the length of mills, the position and number of classifiers, and the total loads a mill should carry.

Jan 1, 1941

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

By W. C. Whittaker

COMPLETED in November, 1943, at a cost of over $1,500,000, Elk River colliery of the Crow's Nest Pass Coal Company, Limited, has been laid out and equipped for an ultimate annual production of 1,000,000 tons and replaces the recently closed Coal Creek plant, which has been operated by the Company for the past forty-five years. The project has involved the opening of mines in three seams, the construction of a complete set of colliery buildings, including a modern preparation plant of 360 tons per hour capacity, and the laying out of the necessary yard tracks and spur connecting the new development with the Company-owned Morrissey, Fernie and Michel railway, which, in turn, connects with the Canadian Pacific railway at Fernie. The colliery is three and a half miles east of Fernie, B.C., near the southern end of the Crow's Nest coal field, which contains the largest and most important body of coal in the Province of British Columbia. The coal-bearing horizon is the Kootenay formation, present in the form of a syncline covering an area of 230 square miles. Most of the coal seams occur in the lower 2,000 feet of the formation, the covering beds being largely coarse sandstones and conglomerates of great thickness, the presence of which accounts largely for the preservation of the coal measures. James McEvoy, in the report of the Geological Survey of Canada for the year 1900, states that the basin appears to contain a fairly constant coal content of nearly 172 feet in 23 seams of a thickness of one foot or over. Coal has been mined in the Fernie district since 1897 and the first shipments were made from Coal Creek colliery in the following year, over the then newly constructed British Columbia Southern railway. Since that time, a total of over 16,000,000 tons of coal has been produced, an average of 350,000 tons per year. The7ears of peak production were 1910, 1912, and 1913, with an all-time high of 924,000 tons in 1913. The lowest output in the history of Coal Creek was that for the year 1933, when only 60,340 tons were produced, the colliery being closed for some months. Present production from Elk River colliery averages 1,150 tons per day, the output being considerably less than it could be were sufficient man-power available.

Jan 1, 1944

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By Denis Labrie

Le minage en profondeur sous contrainte modérée à élevée présente de nombreux défis aux opérateurs et aux ingénieurs de mine notamment au niveau du contrôle de terrain et de l?environnement minier souterrain, pour assurer la sécurité des travailleurs sous terre et la continuité du cycle d?opération. Des conditions de contrainte élevée signifient une pression accrue au front de taille et sur les structures minières tels les piliers de mine et les fins de zone, un risque de rupture violente ou de coup de toit plus élevé, des zones de rupture plus grandes au pourtour des excavations, des charges accrues sur le support de terrain, etc. Le présent article fournit un aperçu du travail fait à l?intérieur du Programme de Contrôle de terrain de CANMET au cours des sept (7) dernières années, entre 1995 et 2001, pour comprendre et suivre l?évolution des niveaux de contrainte à l?intérieur des structures minières. Les propriétés déterminées en laboratoire sur des échantillons rocheux et les prévisions effectuées au moment de la conception sont comparées avec les observations effectuées en chantier à la paroi des excavations et à l?intérieur de la masse rocheuse. La plupart des cas discutés ici montrent une corrélation satisfaisante entre les observations effectuées en chantier d?une part, et les résultats d?essai obtenus en laboratoire et les calculs réalisés lors de la conception d?autre part. Ces observations peuvent donc être considérées comme des moyens relativement sûrs pour vérifier et suivre l?évolution des niveaux de contrainte présents à l?intérieur des structures minières.

May 1, 2002

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987