Search Documents

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By Donald Leroux, Colin Hardie

"New or improved mathematical models of mineral processing machines are published almost on a monthly basis. Often, these models can be calibrated from bench-scale test results and programmed using spreadsheet software to simulate different designs and operating conditions in open-circuit configuration. However, since mineral processing plants frequently operate comminution, separation and/or extraction machines in closed-circuit configurations, open-circuit simulations often have limited applicability.The simulation of closed-circuit configurations necessitates the programming of an iterative loop to bring the circuit to equilibrium. This can be done by using spreadsheet software but often requires advanced programming skills. As an alternative, LIMN® software, which simplifies the programming of closed-circuit configurations within spreadsheets can be used. This software was specifically designed to turn a Microsoft EXCEL® spreadsheet into a closed-circuit modeling and simulation platform with minimal programming.During the past few years, the Mineral Processing Group at the Noranda Technology Centre, has used this software for numerous projects which include the simulation of multi-stage cyclone circuits, closed-circuit regrinding and locked-cycle flotation tests. Using these projects as examples, the flexibility and the easy to use nature of the LIMN® software is demonstrated.INTRODUCTIONMineral processing engineers routinely have to make predictions regarding comminution and separation processes. Predicting the appropriate dimensions of equipment and the process response to changes in operating mode are probably the most common situations that they face. In all cases these predictions are expected to be rapid and accurate.Predictions made by engineers are frequently based on mathematical models. Many first principles, empirical, semi-empirical, steady state and dynamic models of mineral processes can be found in the literature. In fact, new or improved mineral processing models are continuously being proposed and in spite of this variety, process engineers often have to either develop their own or tailor existing models to suit their particular needs."

Jan 1, 2003

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By G. E. Wittur

"The twenty-one members of the Organization for Economic Cooperation and Development, comprising eighteen western European nations plus Canada, the United States and Japan. account for two-thirds of world steel production. The Special Committee for Iron and Steel was formed by the OECD to study trends and problems in the steel industries of member countries. The paper begins with a summary on the Organization, including an historical sketch, its structure, member-ship and objectives. The steel industry of the entire OECD is briefly described before proceeding to a more detailed discussion of various aspects of the steel industries of European OECD members, emphasizing practices and conditions that differ from those in North America. Benefits to Canada of representation at meetings of the OECD Special Committee for Iron and Steel are described."

Jan 1, 1967

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

By Shaun Booth

Automating Delay Reporting to Deliver Effective Maintenance Corporate Background: Technology Company: Matrikon Inc. Global software and service provider of Information Technology and Control Solutions that deliver Business Results. Case Study Facility: Bulga Coal Handling and Preparation Plant <CHPP> Australian site, part of Xstrata, an international Swiss natural resources group. Technology: ProcessMORe ? Missed Opportunity Reporting (Delay Reporting). Matrikon?s technology implemented at many facilities, to deliver effective maintenance Matrikon International Inc. Global software and service provider of Industrial Decision Support, maintenance and control solutions, with universal connectivity to existing systems and work processes. ? 1999 ? 100 employees ? 2003 ? 450 employees ? Our offices: 20 offices worldwide: ? Quebec, Toronto, Edmonton, Calgary, Ft.McMurray, Vancouver ? U.S. ? Australia (formerly Hunter Controls)

May 1, 2003

By J. E. Williamson

Introduction 1. Factors on Which the Design of the Roaster Plant was Based The roasting operation at Lake Shore, it was realized from the outset, would be profitable only if costs and losses could be reduced to a low figure. It was absolutely imperative that the operation should be self roasting over the whole range of tonnages and sulphur grades which might obtain during the life of the mine. The roasting operation could not bear the cost in fuel and labour of even a partially fired roast. To meet this requirement, it was necessary to resort to additional insulation in the construction of the roaster and to provide a more flexible means of rabble cooling than the conventional water jacket (see p. 31). A second basic consideration was that of handling a wet, putty-like concentrate. The operating costs of a drier ruled out the possibility of drying the charge before feeding it to the roaster. Moreover, the dusting which would result from charging a dry product virtually all -40 micron (325 mesh) in size would seriously handicap the use of a dryer. Dust lubrication (p. 3S) due to the back-mixing action of the Edwards rabbles, and the use of a Sullivan slapper ( p. 27) on the concentrate filter, completely solved the problem of handling the roast feed. The third consideration was the reduction of dusting to a sufficiently low point that a Cottrell or other dust collecting system was unnecessary. The Edwards roaster when properly supervised, it is believed, can be operated to give the minimum possible dusting. At Lake Shore, the evidence has been that less than 1 per cent dusting occurs at any time and that the greater part of the dust produced is recovered either in the spray tower or in the dust chambers.

Jan 1, 1947

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By V. J. Southey

"This paper reviews the history of Wabana Mines from 1892 to 1966, inclusive, in order to clarify the essential factors involved in the achievement of maximum mining efficiency and in the search for an acceptable product to satisfy changing market requirements. It outlines the progressive steps taken to mechanize both surface and underground operations, and forecasts anticipated performance, assuming certain major plans could have been implemented. Results of extensive research in the treatment of the complex ore are discussed. Selected processing alternatives are compared as to feasibility in a summary incorporating estimated capital and operating costs."

Jan 1, 1969

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By Zuhair A. Nawab, Muhammad A. Al-Marhqun, Mehmet Guney

"The Atlantis-Il-Deep is a stratified metalliferous deposit located along the median valley of the Red Sea at a water depth of about 2200 m. The metal-bearing mud contains sulphides of zinc, copper and iron with significant amounts of silver, gold and cobalt. A variety of oxide, siliceous and carbonaceous gangue material is also present. Long sediment cores indicate that the thickness of the deposit may reach 25 m, but the average kriged thickness of metal-rich sediments is about 11 m.Mining geostatistics was applied to estimate the Red Sea offshore mineral resources. Experimental semi-variograms were computed along 0 ± 180 degrees and then models were fitted to analyze the mineralization phenomenon. Kriging estimates indicate that 696.330 million t of bulk sediments contain 1.891 million t of zinc, 0.425 million t of copper and 3. 75 thousand t of silver. Gold and cobalt contents were calculated from the analysis of solids in flotation concentrates as 47 t and 5368 t respectively. The significant outcome of implementing geostatistics to the Red Sea brine precipitates is not only for the evaluation of metal resources, but it also provides a useful tool in the optimization of selective dredging of appropriate areas to be mined. IntroductionThe discovery and extensive exploration of hot brines and hydrothermal sediments in the Red Sea median valley revealed the fact that the Atlantis-II-Deep is a potentially exploitable metalliferous mud in the economic sense. Sediments in the mineralized deep are composed mainly of oxides, various types of silicates and sulphides with considerable concentrations of zinc, copper, cadmium, silver and gold. The mineral-rich deposit, located at a mean water depth of about 2000 m, has an average thickness of 11 m, and is covered by a brine layer having a temperature of 60°C."

Jan 1, 1988

By Carol E. Jones

Outline ? Reclamation is a primary mitigation. ? Understand baseline environment and land use. ? Determine reclamation goals. ? Selecting reclamation technology. ? Determine technical risk. Reclamation ? Primary Mitigation ? Through land and water disturbance, mining can have significant local and regional environmental impacts. ? Impacts can also result from associated land use changes. ? Reclamation is a primary tool that the mining industry uses to manage its environmental impacts.

May 1, 2008