Search Documents

By M MacMillan

THE following is a brief description of the method of hoisting ore automatically at the No. 14 shaft of Mcintyre Porcupine Mines, Limited, Schumacher, Ontario. All ore and waste below the 3875-ft. level is hoisted up No. 14 shaft from the 7000-ft. level to the 3000-ft. level. Seventy to seventy-five per cent of the mining is done in this area. The shaft consists of four compartments: a man way, a ventilation compartment and two skip compartments. The hoist, located on the 3500-ft. level (see Figure l), is an 80-in.-diameter, 4-rope friction winder, utilizing two 6-ton front-dump skips in balance. The hoist is powered by a 1,100-h.p. A.C. motor, the maxi-mum speed being 2,400 ft. per minute. The operation can be either manual, push-button automatic from the pocket, or fully automatic. Men can be raised or lowered in the skips, using a collapsible aluminum platform placed inside the skip box.

Jan 1, 1963

By Paul Clayton

Case Study ? Site: BMA Saragi Coal Mine Queensland Australia ? Model: Marion 8050 ? YOM: Mid 1970s ? Boom: 97M ? Bucket: Original capacity of 100 Tonnes upgraded to 125 tonnes at time of filtration upgrade. ? Apps: Swing, Hoist & Drag Gearboxes ? Oil: Oil Castrol Alpha TT1200 Viscosity of 1208 cSt @ 40° C (104° F) 720ltr Oil Volume Trial and Installation Justifications ? To reduce gearbox overhauls. Typical schedule being 5 years. ? Bucket upgrade from 100 tonnes to 125 tonnes. Increased gearbox demand and stress. ? Increase of overhauls out to 10 years + ? Saving per Dragline estimated to be US$8-10M in downtime and maintenance if successful. ? In compliance with BHPBilliton Global Maintenance FLAC program ? Fuels, Lubricants, Air and Coolants ? Cost Justification ? Downtime: 4 days ? Lost production: $420,000 ? Cost of parts: $162,000 ? Labour and misc: $41,000 Gearbox failure cost $623,000

May 1, 2008

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014

By Toivo Toivanen

The paper begins with a brief history of the nickel industry in Finland, and then deals with the introduction of the flash smelting process. The main part of the paper is devoted to nickel refining, which is studied under four main headings -grinding, leaching, electrolyte precipitation, and nickel electrowinning. Flowsheets are illustrated, and the equipment used is described. Analyses of the material in the various stages, from concentrate to high-grade nickel matte, are also presented. N ICKEL made its appearance in the Finnish mining industry forty years ago, when a nickel deposit was discovered at Petsamo in Lapland. Mond Nickel Co. received the concession for this deposit from the Finnish Government, and the Petsamon Nikkeli Company constructed a mine and a nickel smelter (1), the completion of which was prevented by the 1939 Winter War. The mine and smelter were, however, completed soon afterwards in spite of World War II,

Jan 1, 1964

By B. J. Fryer, R. P. Taylor

"As a monitor of the processes involved in the formation of granitoid mineral deposits the coherent group behaviour of the rare earth elements (REE) actively reflects changing fluid characteristics. For example, in the porphyry environment, magmatic-hydrothermal fluids produce potassic alteration with strong enrichment in the light rare earth element s (LREE), reflecting their high pH, low fluid/rock ratios, and the dominant role of CI- complexing in metal (i.e. Cu, Au) transport. With increasing fluid/rock ratios and decreasing pH accompanying the progressive involvement of meteoric fluids (and the production of propylitic, argillic, and phyllic alteration) anionic species such as F - and CO, 2- become important in metal (e.g. Mo, W,) transport through complexing, and their activity in the hydro thermal fluids is illustrated by mobilization of the heavy rare earth elements (HREE).The relative involvement of CI- versus F - versus CO32- in metal transport in other granite-related systems can also be monitored through REE behaviour. Hence granitoid tin-tungsten mineralization and associated greisenization typically exhibit heavy rare earth enrichment and evidence the importance of F' and CO32- in metal transport. Similarly, heavy rare earth element enrichment in hydrothermal uranium deposits can be related to the transport of uranium as carbonate complexes. REE are widely accepted as powerful tools in the study of rock petrogenesis, but their use has been neglected in the investigation of mineral deposits. The recognition of the systematic variation of REE distributions in granitoid mineral deposits suggests that the application of REE geo chemistry, particularly when integrated with fluid inclusion and isotope studies, can provide (1) an effective method for identifying the physicochemical controls of metal transport and (2) a useful criterion for elucidating metal distribution."

Jan 1, 1983

By Curtin University Western Australian School Mines

"Curtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc.) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The model structure, modelling approach, and some scenarios are discussed.INTRODUCTIONCurtin University’s Gold Technology Group has developed an online CIP/CIL simulation model called SIMCIL which has been used since 1999 to model and simulate industrial leach-adsorption circuits. The model has recently been upgraded to include an integrated liberation-leach modelling (ILLM) approach. The ILLM approach provides the means to evaluate the impact of the gravity recoverable gold (GRG) characteristics of the ore (GRG content and liberation behaviour), various process parameters (such as grind size, bleed to gravity, etc.) and circuit configurations on the gravity gold recovery, leachadsorption circuit behaviour and overall plant gold recovery.A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach. The data required for the ILLM calibration can be obtained directly from the 3 stage GRG test, leach tests and size-by-assay analysis of the 3 stage GRG test products, and leach test products.This paper describes the ore characterisation methodology, model structure, modelling approach, and the application of the ILLM."

Jan 1, 2016

By A. J. Faulds, K. C. Westaway, Z. Waszczylo

"PAH compounds have been found in the exhaust from all types of engines burning hydrocarbon fuels . They have also been found in the air over cities and in water. The authors report on a study to assess the concentrations of twelve different PAH compounds in several different environments in dieselized underground mines. In addition, the differences in the PAH levels and distributions in different mines will be demonstrated. Finally, the influence of blasting and the type of diesel engine used as well as the effect of catalytic converters in the exhaust system on the PAH concentration in the mine will be discussed.IntroductionMining methods have been altered significantly in the last 25 years; i.e ., the tools and machinery used underground have changed from electrically operated trains and other equipment to diesel-powered equipment. This has been done for several reasons: 1) economics, 2) convenience and 3) safety. Today, most mines are heavily committed to using diesel equipment.Although the introduction of diesel equipment has revolutionized mining methods and has been a tremendous boon to the mining industry, it has also created new problems. These problems arise because the exhaust from diesel engines contains several pollutants which can be hazardous to the health of the miners. These pollutants are CO2, CO, NO., SO2, oxygenated hydrocarbons produced during the buring process and unburned hydrocarbons. There are two classes of hydrocarbons, of which polynuclear aromatic hydrocarbons (PAHs or PNAs) are a part."

Jan 1, 1981

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By Kathy S. Kalenchuk

Damages have been observed in shafts, backfill infrastructure and the slick line at the Leeville Mine. Shaft damage (shearing and spalling of the concrete liner) is attributed to mine-induced rock mass deformations concentrated where regional faults intersect the shafts. Aggregate bin, mixer station and conveyor drive damage (shotcrete shearing, heave of concrete floor slabs and bending of a vertical steel beams) is attributed to rock mass squeezing induced by elevated magnitudes of the vertically orientated major principal stresses. Separation of the slick line has occurred do to extension of the stressshadowed rock mass immediately above the mined out areas. Three-dimensional numerical models have been developed and calibrated to simulated rock mass deformations with magnitudes similar to those believed to have produced the observed damages. By stepping through the mine sequence, models reproduce deformations at the same mining stage as when damage has occurred. Calibrated models have been used to forward project further damage over the remaining mine life.

Jun 1, 2012

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By Golaleh Riahi

An original method is used to obtain stable nanoparticles of gold-based mono- and bimetallic systems supported on an acidic zeolite. This approach has been applied to PtHY (1wt% Pt) and to bimetallic Pt-AuHY containing 1% of platinum to which is added the amount of gold required to give Au/Pt molar ratios of 20,40,60 and 80%. Metal clusters of Au or Pt-AuHY are formed inside the supercages of the zeolite framework by the thermal reduction of cations by the ligands (en = H2N-CH2-CH2-NH2) under inert gas flow at a temperature depending on the metal. The use of acidic zeolites favours the dispersion of the metal and the thermal stability of the particles. This stability is explained by chemical anchoring of metal clusters by the Brønsted sites of the support. Several techniques have proved that for a molar ratio of 20% metal particles of Pt-AuHY are bimetallic. The segregation of Pt and Au starts for molar ratio =?40%. The catalysts tested on the methylcyclopentane hydroconversion reaction reveal that the addition of gold to platinum leads to an increase in the activity and an improvement in the selectivity for isomerization of the skeleton (cyclohexane and benzene) to the detriment of hydrogenolysis. Similar results were obtained for the dodecane isomerisation to isododecane. These catalysts were also tested in CO, propene and propane oxidation. The activity of fresh catalysts is rather low. It increases after their pretreatment in oxygen or hydrogen atmosphere. In propene oxidation in the reaction mixture O2 ? H2, beside total oxidation of propene to CO2, also propene hydrogenation was observed, particularly at low temperatures. The presence of Au enhances the hydrogenation properties: high selectivities (> 90%) to propane and high propane yields on PtAu HY are observed up to ~150oC, whereas for Pt HY catalyst the selectivity and yield to C3H8 decreases rapidly with the temperature beginning from ~100oC.

Oct 1, 2003

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001

By S. Banisi, M. Maleki-Moghaddam

Direct observation of charge shape and its motion in industrial mills is not possible; therefore, a combination of analytical and physical studies is used to determine charge trajectory. Software packages, which predict charge motion consider only the outermost layer of charge (single ball) and ignore the charge and the interactions of grinding elements. In the new version of the GMT (Grinding Media Trajectory) software, the effect of liners specification and bulk load on charge shape and trajectory are considered. The charge trajectory was measured in a laboratory mill with the diameter of 100 cm and length of 21.5 cm with the transparent end and compared with that of the old version of GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. The model mill was operated at 55, 70 and 85% of the critical speed for five levels of mill filling (10, 15, 20, 25% and 30% by volume). The experiments indicated that the end walls effect was negligible for the model mill with the length of 10.8 cm and beyond. The proposed relationships to correct the trajectory and charge shape were validated by using the new liner of the Gol-E-Gohar iron ore company AG mill. The positions of shoulder, toe, toe departure and impact points were predicted with the relative errors of 5, 0.7, 2 and 0.2%, respectively. The GMT software was updated with the new relationships. The results of GMT simulation indicated that when the lifter face angle increased from 7 to 30°, the distance between the charge impact point and the toe decreased from 40.1 to 11.2° for 30% filling. The change in the position of the impact point meant increasing the probability of charge impacting the toe, not the liner which favored more efficient comminution practice.

Jan 1, 2016

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By I Wilkomirsky

The neutralization of S02 from copper smelter gases to produce calcium sulphate (anhydrite) is considered an attractive alternative to sulphuric acid production. To develop the required technology for the process, a three-stages fluidized bed reactor prototype was designed and operated using both high and low grade limestone and gases with 2, 8 and 12 vol -% S02. The results obtained shows that at 800°C and up to 8 vol-% S02 in the gases, the capture of S02 reaches near 99% with limestone conversion to anhydrite of 45 to 48%. A larger pilot plant is presently being built at the Codelco El Teniente-Caletones Smelter to demostrate the technology and to evaluate the economics of the process. Cu2007

Jan 1, 2007

By M. Souley, G. Armand, M. Ghoreychi, D. Seyedi, J. -B. Kazmierczak

"An anisotropic constitutive model is proposed in this paper accounting for both structural anisotropy and induced anisotropic plasticity. It is assumed that the rock is composed of a matrix and of potential planes of weakness. The matrix is assumed to be linear, transversely isotropic and the plasticity is described by a non linear yield function where the parameters are deduced from the nonlinear Hoek-Brown envelopes in pre- and post-peak, and derived from the laboratory characterization. A non-associated flow rule is used with a distinction between compression and extensional stress paths, as well as the absence of volumetric strain beyond large plastic distortion.The planes of weakness are considered as known a priori or assumed to be oriented perpendicular to the direction of the current minor principal stress. An elastic-perfectly plastic behavior according to the Mohr-Coulomb criterion is assumed in the planes of weakness; while the elastic part is considered as linear and transversely isotropic.Finally, the proposed model was implemented in FLAC3D and used to simulate triaxial compressions to provide a verification of the implementation. The applicability of the implemented model to reproduce damage (pre-peak) and/or failure developments around a circular opening is checked. The GCS drift, one of the mine-by experiments set up at the main level of the Meuse/Haute-Marne Underground Research Laboratory, is selected for this first application."

Jan 1, 2015

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By B. R. Neufeld, M. G. Heximer, S. J. Roach, W. G. Van Luven, D. G. Reynolds

"Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. In the zinc plant, zinc concentrates are roasted to produce calcine, which is then processed in the leaching circuit for zinc recovery. Calcine is first dissolved at pH <2.0. This is followed by a precipitation stage using additional calcine that removes iron as a ferric hydroxide precipitate which is recycled to the lead operations. It is during this pH adjustment that impurities, notably arsenic, antimony and germanium, are co-precipitated with ferric hydroxide which is the primary removal phase for these elements. Recent processing conditions have resulted in lower iron inputs to the leaching circuit and this has resulted in insufficient co-precipitation of key impurities. This paper summarizes the influence of iron concentrations on impurity removal using laboratory and plant scale surveys, and emphasizes key specification limits for the primary iron removal circuit.INTRODUCTIONThe Sulphide Leach Plant (SLP) at Teck Metals Ltd., Trail Operations produces a zinc sulphate electrolyte from three different zinc bearing streams:1. Calcine, primarily containing zinc oxide, from the roasters2. Zinc electrolyte from the Oxide Leach Plant (OLP) is produced by leaching zinc oxide fume from the pyrometallurgical lead smelting operations3. Zinc slurry from the Zinc Pressure Leach (ZPL) autoclaveThe feed sources are blended and introduced to the iron removal process to precipitate iron in the form of a hydrolyzed iron precipitate which is recycled to the lead smelting operation. Along with iron, impurities, namely arsenic, antimony, germanium and silica, also co-precipitate; this process acts as the primary removal step for these elements. Following iron removal, the electrolyte is further processed in the zinc dust purification circuits. Cadmium and copper are removed in the cold stage circuit via zinc dust cementation, followed by cobalt cementation in the hot stage circuit."

Jan 1, 2016

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012