Search Documents

By Yang Shuxin, Guo Qiliang, He Ping, Lu Lizhi, Yao Rui

"We combined stepwise regression and constrained regression statistical method to obtain the best boundary conditions for the calculation of in-situ stress field in Wushaoling tunnel using finite element method. Our numerical results reveal that: the main geologic factors contributing to the initial background stress are gravity and tectonics; the principal stress values would drop in fault zones; the angle between the maximal horizontal stress and the axis of Wushaoling tunnel is acute; Wushaoling tunnel tends to become stable when this tunnel has 2:1 ratio of the height to its width; the possibility of rock-burst exists under high stress.INTRODUCTIONStress state of engineering region is an important factor affecting the stability of project. Geological disasters in the project area are closely related to their stress environment. Wushaoling tunnel which is 20,050 meters long, lying along Lanzhou-Wuwei segment of Lan-Xin Railway in China, is the key project of Lan-Wu double-track railway. The region surrounding this tunnel is under a high stress environment. Accurate identification of the stress environment of the engineering area and the interaction between geomaterials and geotechnical engineering construction holds significant scientific and practical value for engineering design, construction, and operation.Many scholars explored and discussed the present-day tectonic stress through investigations of tectonic evolution history (Ding, & Lu, 1986), crustal deformation (Zoback, 1992), focal mechanisms (Yang et al., 2003, Xie, Cui, & Zhao, 2004), and so forth. However, the above methods would only provide the approximate direction of the principal stress in a broad region, and could not give the absolute stress values. In-situ stress measurement is one of the primary means to directly gauge the current crustal stress. However, in-situ stress measurement can only be applied in small number limited by measurement conditions."

Jan 1, 2015

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By G. Hamel

The LCL&L process (Low Caustic Leaching & Liming) is a patented hydrometallurgical route developed by Rio Tinto Alcan (RTA) to economically process spent pot lining (SPL) generated by aluminum cells. The three resulting end-products (carbonaceous, fluorinated and caustic liquor) are inert and have valorization possibilities. An industrial size pilot plant located in Saguenay (Quebec) was inaugurated in mid-2008 to demonstrate and optimize the technology. This paper describes characteristics of the LCL&L process and the experience acquired by RTA since the plant's start-up, including ramp-up capacity and technology challenges that were overcome. Possible end-products valorization methods are also presented. The carbonaceous end-product can be separated into carbon and brick rich fractions and used as either alternative fuel, reducing agents, or as raw material for third party processes. The development of a conversion process for the fluorinated end-product would allow its reuse as a substitute to fluorspar mineral for aluminum fluoride production. Finally concentrated caustic liquor is already valorized at the nearby RTA Vaudreuil alumina refinery.

Jan 1, 2011

By A. R. Turner

AERIAL survey methods have made enormous technical advances and gained new recognition since World War II. Before enlarging on this statement and reviewing some of the uses of aerial survey in industrial development it is important to de-fine what is meant by "aerial survey". The subject will be discussed in the broadest sense and references will be made to the four sections that compose the overall field of surveying operations from the air. These are: 1. Aerial photography and photo-graphic mapping. 2. The use of airborne electronic instruments for geodetic distance measurement and the determination of ground elevations. 3. Airborne geophysical surveying. 4. The extraction of qualitative and quantitative information from aerial photographs through the processes of "reading", analysis and interpretation. Many sciences and techniques are combined in aerial survey operations. The tools of the business include aircraft, finely engineered cameras, elaborate film processing and printing equipment, ground survey instruments, precision stereo-plotting instruments, map -

Jan 1, 1961

By Jie Deng, Wenliang Xiong, Binyan Chen

"With falling rare earth metal prices, low cost beneficiation of rare earth minerals is essential. The “Flotation-Agglomeration-Magnetic” (FAM) separation process is a newly developed technology by IMUMR to economically recover rare earth elements from different types of deposits. The theory of FAM process is to selectively agglomerate rare earth particles and separate from gangue minerals by bubble flotation process. The flotation product is further upgraded by magnetic separation. The FAM process has been successfully applied in industrial production on the Dalucao rare earth ore, Sichuan, China. The average REO grade of rare earth concentrate is 65% in the latest 12 month production run, with an average recovery of 55%.INTRODUCTIONRare earth elements (REEs) include fifteen lanthanide elements coupled with two chemically similar elements (yttrium and scandium). These elements are split into two sub-groups, La to Sm are classified as light rare earth elements (LREEs) and the remaining elements including yttrium are heavy rare earth elements (HREEs) (Kumari & Panda, 2015). The demand of rare earth elements surged in recent years due to their increasing usage in diverse industrial aspects including high strength magnets, phosphors, clean energy, polishing compounds and catalysts (Goley &Scott, 2014).More than 250 REE-bearing minerals have been discovered, but many minerals are with very low concentrations of REEs, varying from 10-300 ppm (Adam &Ping, 2013). The most common rare earth minerals mined are bastnaesite, monazite, xenotime and ion-adoption REE (Chelgani & Rudolph, 2015; Kanazawa & Kamitani, 2006). Before the 1960s, most rare earth resources were extracted from monazite in the beach placer, with the exploiting of Mountain Pass in the United States and Bayan Obo mine in China, bastnaesite became the chief mineral source of rare earth resources (Klinger, 2015). These minerals are commonly separated with gangue minerals by froth flotation, gravity concentration, magnetic separation, or any combination thereof based on their specific physical characteristics (Zhou & Wang, 2014; Adam & Richard, 2014; Yang & Satur, 2015; Xia & Brian, 2015a,b)."

Jan 1, 2016

By D. R. Pyke

Many of the gold deposits in the Timmins• area show a close spatial association to ultramafic metavolcanics. Available analytical data suggest that ultramafic rocks contain significantly higher gold contents than other major rock types. In addition, recent analyses by Keays (1975) suggest that talc-carbonate alteration of ultramafic rocks releases significant quantities of gold. It is proposed that the ultramafic volcanics formed the principal source of gold for the deposits in Timmins, and that the gold was derived from the ultramafic flows when they were extensively carbonatized. Carbonatization of the ultramafic rocks and emplacement of the auriferous quartz-carbonate veins was probably coincident with the last major period of deformation in the gold camp. Delineation of hitherto unrecognized ultramafic volcanics could be an important guide to the discovery of further gold deposits.

Jan 1, 1976

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By J. E. Dutrizac, J. M. Zinck

Ferrihydrite is often the initial precipitate resulting from the rapid neutralization of Fe(III) sulphate solutions, and it seems to be a major constituent of zinc plant neutral leach residues. The most important parameters affecting ferrihydrite precipitaton are temperature, solution pH and the neutralization rate. Low temperatures and rapid neutralization rates yield poorly filterable ferrihydrite, whereas higher temperatures and slower neutralization rates produce readily filterable precipitates; in all instances, however, the precipitates are two-line ferrihydrite. Significant amounts of Zn are incorporated in the ferrihydrite precipitates, and the Zn contents increase with increasing Zn concentration, pH or temperature. Generally, the sulphate contents of the precipitates decrease as the Zn contents increase, and this may indicate that the Zn is adsorbed on the ferrihydrite. Discrete Zn phases were not detected. Neither Cd nor Tl is precipitated with ferrihydrite, although thallium jarosite co-precipitates with ferrihydrite at high Tl concentrations and elevated temperatures. Virtually all of the Sn added to the solution precipitates with the ferrihydrite, but the tin is believed to be present as intimately admixed amorphous SnO2.nH2O. Although selenite extensively precipitates with the ferrihydrite, selenate remains mostly in solution, likely because of the close similarity of the SeO4 2- ion to the SO4 2- ion which is present in high concentrations and saturates the available sites for anion adsorption.

Jan 1, 1998

By G. A. Gross

"The Soviet Union has enormous reserves of iron ore in many different kinds of deposits that are widely distributed in this vast land area. The present iron ore industry is based mainly on deposits in Precambrian cherty iron-formation at Krivoy Rog, Kursk and Murmansk. Extensive reserves of both naturally enriched hematite ore and magnetite iron-formation in these areas alone could sup-ply all the domestic ore required for several hundred years.Many contact metasomatic magnetite deposits discovery in recent years in the eastern Ural Mountain belt and east of the Kusnetsov basin in Siberia are being developed, with ore reserves measured in billions of tons. Oolitic limonite-chamosite-siderite ores of Cretaceous and younger age at Kerch on the Black Sea and around the east and southern perimeter of the West Siberian basin constitute some of the largest concentrations of iron in the world. These sedimentary ores are low grade, of poor quality and difficult to beneficiate. Banded jasper magnetite and hematite iron-formation in volcanic rocks of Devonian age in Kazakhstan and along the Mongolian border are of special geoloica1 significance.Iron deposits in the Krivoy Rog and Kursk areas were examined and a large number of geologists discussed their work on deposits in many other parts of the Soviet Union during the writer's seven-week study tour of mines and research institutes in Moscow, Leningrad, Novosibirsk in Siberia and Kiev in the Ukraine. The descriptive geology of iron deposits of useable ore and of marginal material has been well documented in the course of systematic work and a large number of scientists are studying fundamental problems on the origin and treatment of iron ore."

Jan 1, 1967

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher productivity rates and a resultant reduction in activity costs. Increased advance rates, by examination of the key components (face preparation and drilling, hole loading and blasting, scaling, mucking and support installation) in the development cycle, and optimizing these processes is a high priority for research in the Canadian mining industry. Support installation time alone is typically 36 to 46% of the total development cycle time. A reduction in support installation time or techniques and alternative scaling strategies could result in significant gains in drift development advance rates. Support Staging and hydroscaling within the drift cycle could offer alternative drift development sequences that could reduce the overall cycle time. MIRARCO?s research into the support and hydroscaling processes for rapid drift development also suggests that there are many other factors (e.g. mine ventilation services) that have a significant impact on the rate of advance. These factors should be considered to promote and manage safe and rapid drift development. Constraints to the rapid drift development processes can only be overcome by sound construction management practices. In other words, the goals of rapid drifting can be achieved by the implementation of contractor-type construction management. This paper examines various constraints and processes affecting rapid drift development and draws attention to other factors affecting safe rapid drift development.

Apr 1, 2005

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

Abstract -The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the F1avrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has yielded 2.75 M tonnes of ore grading 30Jo Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of F1avrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By Rodgers Peale

The Waite mine, as it is locally termed, is situated in the Rouyn district, in the townships of Duprat and Dufresnoy, Quebec, and lies about 340 miles north of Toronto. Due to the impetus given prospecting in the Rouyn district by the discovery, some years ago, of copper-gold ore on the Horne claims, many exploration parties were put into the field. Early in 1925, J. H. C. Waite, C. H. Ackerman, and T. Montgomery staked the claims which now comprise the mine beating their names. Trenching and diamond drilling soon disclosed an ore-body of commercial size and grade, and by the end of 1928 a shaft had been sunk 300 feet and the mine was producing 150 tons of direct-smelting copper ore a day. In the summer of 1925, Dr. H. C. Cooke, of the Geological Survey, made a reconnaissance survey of the property (1), and since that time work of the same nature has been done by several others. MacGregor has published some interesting data on the Amulet mine (2). Using as a background a summer's work on the Horne claims at Noranda, the writer spent the summer of 1929 at the Waite.

Jan 1, 1931

By Andrukaitis. E.

The increasing use of electronic equipment by the Canadian Forces has increased the importance of electric power. A power source that is packed with energy and yet light, small and durable is the common request of military users. However, this needs to be achieved while also addressing the requirements of safety, reliability and low temperature performance. The potential use of fuel cells in a military environment has become a possibility in several areas in the 21st century. Some examples of power source requirements and the materials related R&D required to give better, higher energy power systems in the future will be discussed.

Jan 1, 2005

By C. A. Lorenson

THE Marmoraton mine is located a mile southeast of Marmora, a village in Hastings county, Ontario, 130 miles east from Toronto and 143 miles west of Ottawa. Highway No. 14 from Belleville intersects Highway No. 7 at Marmora and the branch line of the Canadian National railway between Trenton and Bancroft passes through the property just east of the open pit. HISTORY AND GEOLOGY The Marmora orebody appears as the whorls of a thumb print on the aeromagnetic survey map released by the Ontario Department of Min.es early in 1950, the survey of the district having been made in 1948 and 1949, under the joint auspices of the Department of Mines and the Geological Survey of Canada. The 'anomaly' appeared to have interesting possibilities, so Bethlehem representatives carried out a ground survey and began drilling the property in June, 1950. A total of 40 holes, aggregating 37,000 feet, were drilled to delineate the ore-body. The Marmora orebody is a re-placement of Precambrian limesto.ne with zones or bands of magnetite interlaid with metamorpl1ic rocks and cut by later intrusives. The ore and associated Precambrian rocks are overlain by 100 to 150 feet of flat-lying Palaeozoic limestone. It is a low-grade deposit averaging 33 per cent iron and requires concentration to raise it to 65 per cent iron grade.

Jan 1, 1958

By Yong-neng Feng, Xiao-ping Chen, Wei Guo

"While the uniaxial compressive strength of rock has been extensively investigated, the relation between the saturation and natural compressive strength is relatively unexplored. This paper studies on 1865 statistical data of Chongqing Rail Transit Line 1 and Line 6, which located in the Middle Jurassic of Shaximiao formation. The research focuses on the relation between the saturation and natural compressive strength. The statistical data are categorized and quantified in order to ascertain the softening properties of sandstone and sandy mudstone. The findings suggest that the saturation compressive strength is significant effected by its natural compressive strength, and an empirical formula is introduced to explain the relation. These findings have implications for researchers and engineer who concerned with Chongqing rail transit construction.INTRODUCTIONIn the engineering construction and surrounding rock classification, the uniaxial compressive strength index (Ministry of Water Conservancy, 1995; Ministry of Railways, 1999) is one of the essential parameters of rock mass. Usually, there are two types of the uniaxial compressive strength index, natural and saturation compressive strength, and the ratio of them is the softening coefficient. Most of the previous studies on rock strength had focused on the influence factors (Liu et al., 2008; Liu et al., 1998; Liu et al., 2013; Wang, 2013; Zhang et al., 2008; Zhang et al., 2010; Zeng & Lin, 2003) with experiment and in-situ tests. But few publications that reports a long and formal research project on the relationship between natural and saturation compressive strength. In order to figure out this issue, this study investigated the distribution of Solidity Classification of Rock Mass and softening coefficient based on the statistical data of Chongqing Rail Transit Line 1 and Line 6. Based on the analysis, an empirical formula was proposed to explain the relationship."

Jan 1, 2015

By D. J. Xue

Four kinds of coal-rock combination were subjected to three kinds of stress waves in the SHPB numerical simulation. The wave propagation and the changes of the strain energy in the coal-rock combination during the dynamic impact process were recorded as well as the contact force. The dynamic response law of coal-rock combination was obtained. It was found that the coal had better reflectivity than the rock because of coal with larger impedance. In contrast the rock had better transmissivity. As the crest value of the incident wave increased, the increment in the crest value of the transmitted wave weakened in the coal-coal group, coal-rock group and rock-coal group, in contrast, the increment in the rock-rock group increased.

Aug 1, 2013

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015