Search Documents

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

Lonmin RoM ball mills are treating two types of feed ore produced by conventional mining and mechanised mining methods. It was reported that reduction in mill throughput was observed when treating the mechanised mining ore. Detailed grinding surveys were conducted for troubleshooting. Ore samples were collected for breakage characterisation using a JKRBT based on different particle density components. XRD analysis was conducted to investigate the association of minerals with density components. The plant surveys and the breakage characterisation tests all suggested that the two mining methods did not significantly affect either the ore breakage properties or the RoM mill performance. Instead, the mill discharge open area exerted a remarkable influence on mill throughput. The RoM ball mill operated at Lonmin K4 Concentrator has been proven to be a versatile mill that performed stably with variations in feed size distribution and feed ore changes by different mining techniques. The reasons are elucidated by the multi-component breakage characterisation and the plant surveys data.

Jan 1, 2012

By J. Béland, C. Giguère

"The auriferous mineralization at the Sigma-2 gold mine occurs in quartz-carbonate-tourmaline veins emplaced in a fractured granaphyre layer in the upper part of a differentiated gabbro-diorite sill. Kinematic indicators show that fracture planes were active as strike slip, dip-slip (reverse) and tensional faults.Measurements of attitudes of fractures and movement vectors indicate eight different sets that can be grouped into three systems: (I) an east-west oriented system includes a subvertical set and two other sets dipping north and south respectively; (2) a subhorizontal system of two conjugate sets bisected by a third tensional set; and (3)a system of sub vertical conjugate northeast and north-northwest trending sets.Kinematic analysis indicates that the subvertical set of the east west system was subjected to dextral strike-slip movement activated by a northwest-southeast compressive stress whereas the bulk deformation resulting from the remaining and subsequent seven sets can be explained by a protracted subhorizontal north-south compressive stress.The valuable gold mineralization is found principally in the fracture-filling veins of the subhorizontal system and subordinately in the other sets; among these other sets, the NE trending subvertical one is slightly more favourable.The over-all tectonic picture is that of an early mild dextral strike slip faulting in a ductile-brittle medium followed by a general flattening involving, first, a vertical and, later, a lateral extension by fracturing in a medium that had become brittle.The structural features are such that the differentiated sill could not be the source of the auriferous hydrothermal solutions."

Jan 1, 1990

By J. Kabuya Mukendi, F. Brunet, J. Hadjigeorgiou, P. Matte, D. Leblanc, M. Grenon

La stabilité des bancs miniers est un élément important de la conception des fosses. Il n’y a pas de consensus sur les critères à utiliser pour évaluer la fiabilité des bancs miniers. Lors de la conception des fosses, la fiabilité des bancs miniers est analysée à l’aide d’un ou deux critères. L’objectif de cet article est d’analyser l’efficacité de la conception des bancs miniers de la fosse Tiriganiaq du projet minier Meliadine par rapport à des critères de fiabilité rencontrés dans la littérature et la pratique. L’article présente les similitudes et les différences entre les résultats obtenus pour les différents critères et propose une approche multicritère systématique pour évaluer la fiabilité des bancs miniers à l’aide de cartes de susceptibilité.

Jan 1, 2012

By D. W. Rogers

Several commercial polyacrylamide flocculants most widely used in Western Canadian mineral processing plants have been analyzed chemically and compared in standardized settling tests as aids to thickening and clarification. Data are included for both dry and liquid-type flocculants. Percentages of active ingredients in these commercial products varied Widely. Performances were compared on the basis of: equal additions of active ingredients, nearly equal molecular weights and nearly equal degrees of ionic character. Based on zone settling velocities and supernatant clarities of siliceous slurries coagulated by lime additions, dry flocculants proved more economical than liquid flocculants. Using these same two criteria, the most highly anionic were more effective than either weakly anionic or non ionic polyacrylamide- type flocculants.

Jan 1, 1978

In Canada and other countries, legislation dealing with accurate factual disclosure for mining projects is being expanded to include more metallurgical design information. Grinding characteristics, metallurgical recovery of contained metal and environmental hazards associated with tailings disposal will be part of the Canadian package. This paper will examine only that portion of the plant design standard practice that relates to grinding ? in SAG mills and ball mills that grind ore from as received crushed material to final ground product that is fed to downstream plant recovery processes. Since grinding plants represent a significant portion of the overall concentrator cost, accountability in grinding design should no longer be left to chance, opinion, or hidden proprietary information. This is the 21st century. It is reasonable to expect that a factual basis will be needed so that a Qualified Person (QP) reviewing the grinding mill design can understand it. That will also involve how many and what quality of samples are taken to define the characteristics of the deposit, the accuracy of the tests used to measure ore hardness and the method by which the dimensions and power of the mills are determined. If these criteria are not met, the QP may have no choice but to call attention to the lack of convincing information regarding the grinding mill design for the project. At the same time clients are expected to demand getting the correct design information at a cheaper price, results in a more timely way, and accurate design to the point where the risk of tonnage shortfalls are reduced or eliminated. Tables will be presented to show how this can be done to current standards using existing technologies. At the same time it is acknowledged that current standards are ill-defined and that to achieve consensus among those involved in SAG mill design work, it may require that a consortium funded project be set up to establish what tests and methods for grinding design are suitable to meet the new standards for metallurgical disclosure. By running parallel design methods on several major projects over a period of 5 years, the process of how to design grinding circuits will be better understood because the projects will start at the design stage, include procurement of the mills and will end with a benchmark test on the plant. Selecting the samples and the best schedule for doing test work on core samples submitted and mill design, will be discussed in this paper. The issue of completing the grinding design in time for early procurement decisions is on the critical path for most major projects. Discussions between mining engineers, geologists and process engineers are needed early in the development cycle, at the scoping study level (SS), preliminary engineering assessment (PEA), prefeasibility study (PFS), and at the feasibility study stage (FS), to ensure that proper planning for design sample selection is done. Using adequate sampling and testing methods in a timely way allows early procurement of the grinding mills and minimizes project risk.

Jan 1, 2012

By Javier Linares García

At then end of this year will be 10 years of producing concentrate for Antamina. This is a summary of what occurred over the last decade to increase production and tonnage above the design tonnage of 70,000 tonnes per day, up to an average of 100,018 tonnes per day in 2010, an increase in production of 42.9%. Equipment currently in use is the originally installed equipment, signifying a meaningful increase in capacity without capital. In this paper, the different phases of improvements and the realization of their impacts in chronological order will be outlined. Figure 1 below shows the average daily tonnage processed each year (tonnage throughput each year/calendar days), as well as the percentage increase over the tonnage of design.

Jan 1, 2012

By D. Tetsuka, H. Okamoto

The amount of impurities to be processed in a copper smelting process has increased for recent years because of an increase in the electronic scrap amount. It has been found that Sb and Ni effect on the operation of our copper electrorefining process. It is found that the current efficiency of the copper electrorefining tended to be decreased as the Ni concentration in the electrolyte increased. The passivation of the process seemed to be more related to SO4 concentration in the electrolyte rather than the Ni concentration in it. The current efficiency decreased when the Sb content in the anode was high. A high Sb content in the anode caused easy passivation by forming a gel-like film in the slime layer. We have developed a method to for see the anode passivation in a short time while generating a slime layer. We confirmed the tendency of passivation through the experiment of changing Pb content in anode. Passivation was easily occur with an increase in Pb content in the anode. The amount of slime increased as the Pb content in the anode increased. This suggests that passivation was facilitated because liquid diffusion near the anode was inhibited. INTRODUCTION The amount of impurities to be processed in copper smelting has been growing in recent years because the amount of electronic scrap has increased. Figure 1 shows that the contents of Sb and Ni in copper anodes have increased since 2007.High Sb and Ni contents in the copper anode decreased the current efficiency of the process and made the quality of copper cathode poor because of the anode passivation and the formation of floating slime in the electrolyte during electrorefining. If these influences of impurities are suppressed, it would be possible to make copper electro-refining current density higher and to process much amount of electronic scrap. We examined the components of our copper electro-refining process like anode composition, slime properties and electrolyte composition, and investigated the mechanism by which Sb and Ni affect passivation and current efficiency. When examining the influence of Ni, we noticed that the SO4 important. The effect of SO42 – was also discussed

Jan 1, 2019

By P. Curry, H. G. Stephenson, B. Van Den Bussche

"Three Sisters Resorts Inc. currently owns a2035 acre (824 ha) parcel of land, which previously belonged to Canmore Mines Ltd. Approximately 50% of these lands, that are slated for residential, resort and recreation development, have been undermined for coal in one or more seams.Norwest Mine Services has been contracted by the developer to assess and advise them on any past mining activity that may be potentially hazardous to their development and offer solutions to how these hazards may be mitigated or avoided.The following paper deals mainly with the procedures put in place and accepted by the approval authorities, and the Staged approach to the Investigative Procedure that Norwest follows in the mining assessment and mitigation work for Three Sisters."

Jan 1, 1996

By S. S. Burns

"AbstractShovels of 18 cubic yard capacity and larger are described which incorporate advanced technology and techniques providing performance and operation tailored to meet the needs of open-pit mining.To achieve the goal s of increased production at lower cost with consideration of maximum availability, lower energy consumption per ton and low •impact on pit power, Harnischfeger Corporation developed a solid -state drive system (""Electrotorque"" - P&H trademark) and applied unique transmission methods.To date, more than 250,000 hours of experience in different parts of the world under varying operating and environmental conditions has proven that the ""Electrotorque"" shovel is the shovel of the future, today.This paper will discuss the electrical features and touch briefly on some mechanical features.Introduction to ""Electrotorque""THE hoist, crowd, propel and swing machinery of an electric mining shovel are driven by direct-current motors.A D.C. motor is used instead of an A.C. motor because the torque output per ampere input is at a maximum and the fact that it is doubly-fed (armature and field ) provides optimum flexibility in control.The power that is available in the pit is alternating current power. It is therefore necessary to change or convert this A.C. power to D.C. power so that the D.C. motors can be used."

Jan 1, 1977

By J. W. Meier, J. O. Edwards, R. C. Bell

"IntroductionTHE DIE CASTING industry .as we know it today is the direct result of the invention and development of die casting machines during the nineteenth century and of reliable alloys in the twentieth. The early machines were designed to cast low melting point metals such as lead .and tin, and their alloys.It was inevitable that, as these die castings were put into service, the demand should arise for stronger materials. Zinc alloys, often containing lead, tin, copper, and aluminum as major constituents, were relatively easy to cast and stronger than the lead and tin alloys. However, it became apparent after a number of years that these zinc alloys tended to become brittle, distort, and corrode, particularly if kept in warm, humid atmospheres. Thus, considerable quantities of zinc-base .alloys were in use before the trouble was realized and effective measures could .be taken to determine the cause of the instability.The deleterious effect of certain metallic impurities on the properties of zinc •die casting .alloys has now been known for about thirty years. Brauer .and Peirce, and, later, other research workers of the New Jersey Zinc Company such as Anderson and Werley, discovered the pronouned effect of lead, cadmium, and tin on the stability of zinc-alloys."

Jan 1, 1952

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By C. H. Buck, A. J. Taylor

"In 2015 Vale’s Clarabelle Mill began the process change to enable a higher degree of Cu separation. The flowsheet modification was part of a complete divisional flowsheet change being implemented in Vale’s Sudbury Operations. This paper will centre on some of the Operational Readiness (OR) work, culminating in the commissioning of the circuit in March 2017. The emphasis will be on the implementation of an integrated test plan to prepare for the process flow change through the mill.BackgroundClarabelle Mill (CBM) began making a saleable Cu concentrate in 2006 with the installation of the Cu separation circuit. Typical separation rate was 35-40% of Cu in feed reporting to Cu concentrate based on a target Ni concentrate Cu:Ni target of 0.7-0.8. The remainder of the recovered Cu (55-60%) reported to Ni concentrate and was smelted through the Copper Cliff Smelter.In 2013 a capital project, Surface Facility Upgrade (SFU), was implemented to focus on matching the surface plants capacities with the future mine plan to maximize revenues. This was to be achieved by redistributing the metal flow, specifically Cu, through CBM to increase metal unit content through the Smelter. The amount of redistribution of Cu was determined to be based on maintaining a stable Cu to Ni ratio (Cu:Ni) in the Ni concentrate.The change in Cu:Ni ratio in the Ni concentrate would affect the Sudbury divisional flowsheet, and required process changes across the all of the surface plants. The detail that surrounds the flowsheet changes as a whole will not be discussed, but the outcome of the decisions plays a large role in the operational readiness interactions between the mill, its suppliers and its downstream customers."

Jan 1, 2018

By A. Roy MacLean

"In the Maritimes, there are twelve coal areas. From east to west, these include the Sydney coal field, the St. Rose - Chimney Corner, Inverness, Mabou, Port Hood, Pictou, Colchester - Debert, Springhill, Joggins - Chignecto, Beersville, Lake Stream, and Minto. The first eight are in Nova Scotia while the remaining four are in New Brunswick.In all these areas, the coal was formed during the Carboniferous period, which existed some 300 million years ago. However, within this period not all coal formation took place during the same time. There were three main intervals, which occurred at the time that the Riversdale, Cumberland and Pictou groups were laid down (Hacquebard, 1970). The oldest coals are those of the Riversdale Group. These coals were of rather limited extent, and only a few mineable seams are present, particularly at St. Rose -Chimney Corner and Port Hood. From these two areas only 2 M tons have been extracted, and 'measured' resources of 7 and 9 M tons respectively remain. The Cumberland Group coals are confined to Cumberland County and include the coals of Springhill and Joggins River Herbert -Chignecto. Some 43 M tons have been removed and only 7 M tons of 'measured' coal remain, with an addit10nal 39 M tons of 'inferred' resources. However, there are additional resources at Springhill, which will be discussed in more detail in a later section. The coals of the Pictou Group are the youngest and the most abundant, both in actual number of seams and in regional distnbution. These coals were formed during the Westphalian C and D, a time during which the main coal deposition in Europe also took place. Here belong the coals of the Sydney, Inverness, Mabou, Pictou, Debert, Beersville, Lake Stream and Minto fields. Their total production amounted to 469 M tons or 91 % of the Maritime total of 514 M tons. The remaining resources of all Pictou Group coals have been calculated at 254 M tons of 'measured' coal and 949 M tons of 'inferred' coal. As can readily be seen, the bulk of both past production and remaining resources occur in the Sydney coal field. The Sydney figures represent 73% of total production, and 87% of total 'demonstrated' resources in the Maritime Provinces. Next to Sydney, the Pictou coal field has been the greatest producer, with 59 M tons; it also has the second largest 'measured' resources, amounting to 25 M tons. However in terms of 'inferred' coal resources, the Mabou coal field, ~ith 140 M tons, ranks second to Sydney."

Jan 1, 1985

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934