Search Documents

By Nelson C. White

This paper summarizes the present state and future prospects of the potash industry, with special reference to its impact on production in Saskatchewan.

Jan 1, 1968

By Fazel G. Jahromi, Ahmad Ghahremaninezhad

Enargite (Cu3AsS4) is a major complex copper mineral and often is a carrier of invisible gold particles. Pyrometallurgical treatment of enargite is challenging due to the arsenic release to the environment. Hydrometallurgical treatment, on the other hand, appears to be a promising alternative for enargite processing. In an atmospheric enargite leaching process both the copper and arsenic from the mineral can be leached into a sulphuric acid solution and the arsenic can be simultaneously precipitated as ferric arsenate. The unlocked gold in the residue then can be recovered in a subsequent cyanidation circuit. The downside of the atmospheric enargite leaching in sulphate solutions is the slow leaching kinetics. In this study the effective parameters of the atmospheric enargite leaching process in ferric chloride media were investigated. All the experiments were carried out at temperatures below 100 °C. The process parameters that were investigated in this study included ferric, chloride, sulphate and cuprous concentrations, temperature, mixing rate and leaching slurry pulp density. It was found that the copper recovery rate increases with the addition of cupric chloride and also with raising the temperature. The highest leaching kinetics and the highest overall copper recoveries were achieved when cupric was initially added to the leach solution and at 90 ºC.

Jan 1, 2015

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By Juan Asalgado

The JORC and NI43-101 codes impose that mineralized material has a reasonable prospect of economical extraction to be classified as Mineral Resource. For deposits close to surface and amenable to open pit mining, it is easy to show reasonable prospect of economic extraction running a Lerch-Grossman optimization. The Lerch-Grossman pit provides a transparent and repeatable way of separating the Mineral Resource (within the pit) from the remainder of the mineral inventory (outside the pit). Deposits amenable to underground mining are more challenging because of the variety of the underground methods. AMEC developed a stand-alone software package that outlines the material which has reasonable prospect of economic extraction for open stoping, block caving, sublevel caving and room and pillar. The software takes a block model file in ASCII and exports a 3D surface outlining the part of the mineralization that has a reasonable prospect of economic extraction, and which the Qualified Person can smooth out manually if required.

Oct 1, 2009

By John Knox

The object of this paper is to present an analysis of the major problems encountered both in the design and application of downhole drills. Particular reference is made to design features governed by: physical size limitations; metallurgical material standards; physical operating environment; range of commercial materials to be drilled; high power output required, coupled with simplicity from the operating and maintenance viewpoint; and bit design. The history of attempts to develop downhole drills is discussed, and representative mechanical configurations are illustrated. The general design and application aspects of the different types are commented on. The application of this drill type in various commercial fields, such as (a) oil-well drilling, (b) open-pit mining and (c) underground mining, is discussed, along with the limitations presently imposed by the commercial state of the art in the manufacture of accessory equipment; e.g., drill rods, air compressors, mountings, etc. Suggestions on the possible future direction of the development and application of this tool are put forth.

Jan 1, 1965

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

By G. Mihaylov

The basic principles of systems analysis are presented. A model has been designed to determine the location of the Main opening in the presence of three or more stock orebodies. The necessary condition is to find a location for the Collection point which is an essential element in opening up each orebody (stock). The model takes into account the total transportation costs from each orebody to the collection point. Three variants are considered provided that the orefield is divided into two levels at least: - a collection point is designed at every level; - a collection point is designed at the lowest level, i.e. where the so-called concentration level is formed; - the collection point is located at a point between the planes of the two levels; The effect of the depth of mining and mine output on determining the method of opening up the orefield has been analyzed by considering a vertical and/or an inclined shaft. A function has been constructed which allows for investigating in both a static and dynamic regime the capital costs for constructing the whole complex including the shaft. The character of the function does not allow finding the global limits. Therefore, it is of particular importance to specify the limiting conditions. In this case these are the flow capacity of development openings and the shaft. The basic groups of cost and natural indicators for assessing and selecting an optimal technological solution have been systematized. The combined analysis of the two approaches to finding the location of the Main opening and determining the mining method enables us to determine when an inclined shaft is best, and the depth at which opening by a vertical shaft has no alternative. Thus, a transition area is formed for which the selection of an optimal technological solution requires an analysis similar to that proposed in this paper. Conclusions are finally drawn which serve as a basis for determining the areas of application of each opening, including the use of a combined scheme of mine opening. The approach presented can be used in both investigating the possibilities for opening up new orefields and reconstructing existing ones in cases when the mining operations go deeper.

Aug 1, 2013

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By J. G. Whellock, J. W. Matousek

"In spite of their importance to the economics of many metallurgical projects, the values and technical aspects of precious metals losses in smelting operations are relatively undeveloped subjects. This paper attempts to provide a condensed overview of precious metals losses in pyrometallurgy, using some of the limited production and experimental data available. It is intended for three general groups of metallurgists - operators attempting to improve recoveries, cost-accounting engineers making estimates of metal losses in new or modified smelting plants, and research engineers and students.Distribution coefficients of precious metals, the ratios of metal or matte assays to slag assays, are convenient means of comparing smelting processes and the tendencies of the different metals to enter the slag. For silver in lead blast furnaces this ratio is approximately 250;for gold and the platinum group metals in submerged-arc, electric furnaces it is 900. The ratio for gold and PGMs in converters varies with the degree of oxidation of the charge. The over-all cycle-average for industrial installations is tentatively estimated to be 35.IntroductionThe magnitude of precious metal s losses in pyrometallurgical operation s is difficult to assess. The primary producers are generally reluctant to discuss the subject. The by-product producers (the large sulphide smelters o f copper , nickel, and lead) might be more willing to disclose information, but these have precious metals in their feeds in such dilute quantities that accurate accounting is extremely difficult. It is not until numerous processing steps have been taken t hat the precious metals become sufficiently concentrated to permit acceptably accurate sampling and analytical procedures to be followed. Thus, knowledge of the precious metals contents o f the intermediate mattes and slags may simply be unavailable."

Jan 1, 1990

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By Christopher Andreae

Years before iron and steel works were established at Sydney, several thriving although short-lived iron works operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron works. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principal fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel works dominated production for Nova Scotia and the rest of Canada. Two sites achieved prominence in the nineteenthcentury Nova Scotia iron industry: Londonderry and Ferrona (Fig. 1). Londonderry, the larger and longerlasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace. But once the furnace was blown out in 1904, the population gradually drifted away.

Jan 1, 1999

By CIM Standing Committee

The CIM Definition Standards on Mineral Resources and Reserves (CIM Definition Standards) establish definitions and guidance on the definitions for Mineral Resources, Mineral Reserves, and mining studies used in Canada. The Mineral Resource, Mineral Reserve, and mining study definitions are incorporated, by reference, into National Instrument 43-101 – Standards of Disclosure for Mineral Projects (NI 43-101). The CIM Definition Standards can be viewed at mrmr.cim.org. Readers should be aware that reports written by persons issuing technical reports that disclose information about exploration or other mining properties to the public in Canada are governed by a number of securities regulations.

May 10, 2014

By S. A. Pence, A. I. McCallum, V. de Korompay

"Special salt protection rings containing a water-swell• able, polymeric sealant are in successful operation in Canadian potash shafts. Installed above the Prairie Evaporite salt formation at a depth of 3,000 feet, the sealant is preventing formation water migration into the salt and pressure build-up on the concrete lining of both production and service shafts. The salt protection rings are not under the hydrostatic pressure of the formation water.The chemical sealant in use has the unique property of imbibing water and swelling. •Therefore, any water at• tempting to flow by the seal ring actually produces a tighter seal.The purpose of this paper is to discuss the sealant and its properties and uses. Installation of the material and its operation in two Canadian mine shafts is described."

Jan 1, 1971

The Millennium deposit, located in northern Saskatchewan between the McArthur River mine and the Key Lake mill, has considerable potential for becoming an operating mine. Located in the Athabasca Basin, Millennium is blessed with both the riches and the challenges that this basin offers. The potential for ground water inflows during shaft sinking, and the unconventional challenges associated with underground uranium mining, render the successful development of a new mine in this area especially rewarding. The preliminary design and engineering of the Millennium Project has tapped into the experience of other operations in the area, and has utilized new applications of geophysics technology to enhance the understanding of the local geological structure. This discussion will focus on the innovations, and the challenges specific to uranium mining, for a deposit that is poised to be one of the next mines to supplement Saskatchewan's uranium resources.

May 1, 2008

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By W. J. Li, L. Kong, G. L. Li, X. M. Xi, J. Qiu

"A novel hydrothermal method was applied to prepare the precursor of LiMn2O4 using pre-treated electrolytic manganese dioxide (EMD) and lithium hydroxide as the main raw materials. The precursor was subjected to heat treatment between 400 and 900ºC to obtain spinel Li1.05Mn1.95O4 and Li1.035Co0.035Mn1.930O4 positive materials for lithium ion batteries. The structure and morphology of the obtained powder materials were studied in detail by means of X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the precursor has an amorphous structure and a high reactivity, which is easily transferred to spinel structure during heat treatment, obtaining a positive material with an uniform structure and good performances. The XRD patterns reveal that single phase spinel Li1.05Mn1.95O4 can be obtained from the precursor after heat treatment at 600°C in air. The final Li-rich Li1.05Mn1.95O4 product obtained showed a well-defined stable spinel structure and distinctive crystal faces with particle size between 200 and 300 nm. The as-prepared Co-doped spinel sample exhibited a excellent electrochemical performance with an initial discharge capacity of 113.0 mAh/g and 93.8% of its original value was retained after 100 charge-discharge cycling at 0.5 C.INTRODUCTIONThe increasing demand for portable electronic devices and hybrid or full electric vehicles is driving the development of cheap, efficient, compact lightweight and environmental friendly rechargeable batteries systems (Chung et al., 2002; Scrosati, 1995). Lithium ion secondary batteries have satisfied this demand to a greater degree than other battery systems. The cathode material plays a critical role in the performance of Li-ion batteries. The high cost and toxicity of cobalt compounds for the cathode material of LiCoO2 has prompted a search for alternative materials. LiMn2O4-based spinels offer a potentially attractive alternative to LiCoO2, due to its abundance, low price, ease of preparation, environmentally friendly characteristics, better thermal stability, and its effortless recycling (Tarascon et al., 1991; Yabuuchi and Ohzuku, 2003; Amatucci et al., 1999; Tsai et al., 2003). Some achievements have been created to meet the requirements (Guo et al., 2010; Kang et al., 2005; Park et al., 2008; Takahashi et al., 2006; Lee et al., 2001; Yoshio et al., 2001; Arumugam et al., 2008). However, the largest obstacle encountered in the practical applications of LiMn2O4 is its fast capacity fading during long term cycling, which is due to Jahn-Teller distortion of the [MnO6] framework, the electrolyte decomposition at high potentials and manganese dissolution into the electrolyte (Fey et al., 2003). The electrochemical performance of LiMn2O4 is also strongly dependent on its morphological properties, such as crystallinity, phase purity, surface area, grain shape and particle size distribution, etc. All these morphological properties are closely related to the material synthetic routines and heat treatment processes (Huang et al., 2000; Myung et al., 2000; Takada et al., 1998)."

Jan 1, 2012

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

Orebodies of the Renison Bell - Mt. Bischoff tinfield in Tasmania are stratabound, conformable lenses of massive cassiterite-bearing pyrrhotite, with underlying discordant, fault-fracture-controlled and more siliceous ore. The deposits occur in eugeosynclinal, trough-deposited sedimentary and mafic volcanic rocks which are stratigraphically equivalent to diff erentiated volcanic rocks that contain volcanogenic massive base metal sulphide deposits in a parallel arc to the east. Textures of the massive pyrrhotite ore suggest that it has undergone metamorphic recrystallization. Although the massive ore contains both monoclinic and hexagonal pyrrhotite, a study of a few samples from one orebody suggests that their distribution is stratigraphically controlled, with the monoclinic variety abundant only at the base. The distribution pattern of rare-earth elements in massive ore is similar to that of volcanogenic massive base metal sulphides in New Brunswick, and suggests that mixing of sea water with exhalative hydrothermal brines occurred during ore deposition. Tin is a common accessory element in many volcanogenic massive base metal sulphide deposits providing strong evidence that it, too, is transported and deposited by volcanic affiliated hydrothermal brines. Sedimentary rocks containing the massive orebodies are fine grained, thinly laminated, compositionally banded and of mixed chemical sedimentary-tuffaceous origin. They include finely recrystallized chert, carbonate-rich and pyritic varieties; and soft sediment deformation structures in these rocks suggest that dense sulphides deformed underlying, less dense chert prior to lithification. Close to ore the chert becomes massive and coarsely recrystallized, as does the carbonate, which is here strongly enriched in Fe and Mn. Apatite is present in pyritic, cherty and carbonate-rich beds and in the ore itself, in all of which it shows a similar pattern of rare-earth element distribution, suggesting that it is of marine sedimentary origin. These deposits have traditionally been considered as epigenetic replacements of favourable carbonate horizons by hydro thermal flu ids derived from later Devonian porphyritic intrusions. Some of these intrusions have associated tinbearing greisens. The above relationships suggest, alternatively, that, like massive base metal sulphides, the tin deposits were of original syn-sedimentary origin. Circulating hydrothermal brines generated during early Cambrian eugeosynclinal subsidence and tectonism rose through steep fault-fractures, there giving rise to the discordant orebodies, and were discharged on the sea floor, where the massive pyrrhotite lenses were precipitated with the associated cherts and carbonates. In some places, Devonian intrusions remobilized the earlier deposits, forming greisens and newepigenetic veins. Finally , the geologic selling of these deposits, in trough deposited sedimentary and mafic volcanic rocks, suggests another favourable environment for massive sulphide exploration which is quite different from the domal felsic volcanic environment so heavily favoured currently in North America

Jan 1, 1979