Search Documents

By G. M. Brownell

Introduction Within the past year a new deposit of gypsum has been opened up and brought into production in the Province of Manitoba. Until 1930, Manitoba's entire production came from Gypsumville, northwest of Winnipeg, at mile 161 on the Gypsumville branch of the Canadian National railway. However, during 1930 a gypsum bed was opened up at a point one mile south of the village of Amaranth, forty miles north of Portage la Paririe, on the west side of lake Manitoba (See Figure 1). Although no exposure has yet been discovered, the presence of gypsum below the surface in that district has been known for many years as the result of drilling for water. In 1929, J. R. Spear (1), of Winnipeg, interested some local capital in the possibility of .finding commercial deposits of gypsum, and, after some exploration work in the area with a well drill, the Amaranth deposit was located. Sixteen holes were put down at intervals of 400 or 500 feet, all of which encountered what appeared to be a continuous bed of gypsum, about thirty-eight feet thick, at a depth of 92 feet. The extent of the deposit has not yet been determined.

Jan 1, 1931

By J. M. Cummings

The importance of controlled sand properties to the production of quality castings has been recognized by foundry men for many years, but the maintenance of requisite standards results in a relatively high sand consumption, which in steel foundries, for instance, may range from half a ton to over one ton of sand per ton of finished casting. During the war, obtaining and maintaining adequate sand supplies became a serious problem in many foundries, owing to increased wartime production and serious 'bottlenecks' in transportation. As a result, considerable interest was aroused in the possibilities of various sand reclamation systems by which up to 85 or 90 percent of discarded sand may be returned to a usable condition. During the past five years or so, a number of sand recovery installations have been made by both ferrous and non-ferrous foundries in Canada and the United States, and have resulted in substantial reductions in sand costs in every case. The possible benefits of sand reclamation are particularly apparent in British Columbia where no suitable sands for steel and heavy iron foundries occur naturally, and where freight costs on imported sands are considerably higher than initial selling prices. This is well illustrated by the fact that silica sand, which sells for about $2.00 per ton at pits in Illinois, is laid clown in British Columbia for around $11.00 or $12.00 per ton. The operating costs quoted for certain of the reclamation schemes, i.e. $0.25 to $1.50 per ton, may actually be no higher than the cost of waste sand disposal in city-located foundries. In view of the foregoing considerations, the British Columbia Research Council has undertaken a study of the possibilities for sand reclamation, with particular attention directed to its application in local steel foundries. No commercial occurrences of silica sand are known in the Province, and, with this in view, the Council previously investigated the possibility of recovering silica sand from local impure sands. Results were definitely encouraging, but it was felt that the present market is too small to permit economical production by the method developed.

Jan 1, 1947

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By E. A. Brown

"IntroductionBACK IN THE nineteen-thirties, when Eldorado was a private company and was preparing to become Canada's first radium producer, the Mines Branch in Ottawa did much work on the development of chemical processes for the Port Hope refinery (1).In 1945, after the Canadian Government had taken over Eldorado for •atomic energy reasons, the Mines Branch was called upon again, this time to help out by looking into ways and means of improving ore treatment methods for the mine at Great Bear Lake. A group of technical men was assembled to devote full attention to this work, which was known as the Eldorado Project.Three years later, in 1948, the Government decided to reopen the development and operation of uranium properties to private enterprise.Since it is a function of the Mines Branch to assisit private development of Canadian mineral resources, this new uranium policy made it important for the Branch to be in a position where it could provide up-to-date services, technical assistance, and information relating to treatment of radioactive ores, mineralogy of radioactive ores, and assay methods for radioactive ores.At the same time, .because of the demand for increased uranium production, lower grade ores had definitely come into the picture, ores that might be of decidedly lower grade than, say, Eldorado pitchblende, and of entirely different nature."

Jan 1, 1953

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997

By B. Yu, Y. O. Oyediran, M. Robart

"This paper presents the latest flotation development testwork conducted in 2015 on the ‘B Zone’ samples from the Strange Lake Alkalic Complex (SLAC). Since the discovery by Iron Ore Company of Canada (IOC), metallurgical development has been under taken by a number of mining companies targeting various value metals, including yttrium, zirconium, niobium, and rare earths.Most recent, Quest Rare Minerals Ltd. (Quest) completed a Pre-Feasibility Study (PFS) in 2013 where the flowsheet was relatively complex and led Quest to explore alternative options. In 2014, the PFS flowsheet was simplified and one of the features introduced was pre-concentration by rougher flotation. The combined rougher flotation concentrate and slimes successfully recovered >90% TREE in 60% mass thus reducing capital cost and technical risks of the downstream hydrometallurgical processes. The latest flotation development testwork focused on achieving a pre-concentrate in which >80% TREE are recovered in 20% mass. Two separate reagent schemes, based on an ester phosphate collector (Clariant 1682) and a benzoylhydroxamic acid collector (Florrea 7510), were developed. Parameters evaluated in the development testwork included desliming, secondary yttrium and zircon collectors, depressants, temperature, conditioning temperature, time, and density, pH, sodium silicate type, cleaning, and flowsheet configuration. Both developed reagent schemes achieved the targeted metallurgy.INTRODUCTIONThe Strange Lake Alkalic Complex (SLAC) was discovered after geological survey and mapping studies by Geological Survey of Canada and Newfoundland and Labrador Department of Natural Resources between 1967 and 1980. Subsequent exploratory drilling programs by Iron Ore Company (IOC) in the 1980s found that the REE and high field strength element (HFSE) mineralization were within the central region of the SLAC which was named A Zone by IOC and later renamed Main Zone by Quest Rare Minerals Ltd. (Quest). Additional exploratory drilling outside the Main Zone by IOC and later by Quest, led to the discovery of B Zone, which was recognized as the most significant deposit of rare earth elements, yttrium, and zirconium in the SLAC. The B Zone Indicated Resources are estimated at 278.13 Mt at 0.93% total rare earth oxide (TREO) and Inferred Mineral Resources are estimated at 214.35 Mt at 0.85% TREO (Oyediran et al., 2014)."

Jan 1, 2016

By A. J. Makoka, B. C. Qi

Reliable monitoring of corrosion is vitally important in the combat against corrosion and over the last two decades the interpretation of electrochemical noise has received considerable attention as a means to discriminate between different types of corrosion. To this end, many different analytical methods have been proposed, such as power spectral density analysis and analysis via various other stochastic criteria. However, although many corrosion systems are nonlinear and therefore not readily interpretable by the abovementioned analytical approaches, few studies in the analysis of electrochemical noise to date have exploited advances made in the analysis of nonlinear systems. In this paper, the use of phase space methods to analyze and detect change in corrosion systems via electrochemical noise is considered. In particular, the electrochemical noise data are used to reconstruct trajectories in the so-called phase space of the system and changes in the topology of these trajectories or attractors as represented by correlation dimension curves are consequently interpreted as an indication of change in the dynamics of the system.

Jan 1, 2005

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By Daniel Lachapelle, Nuri Hmidi, Turgut Yalcin

"Simulation can serve as a convenient tool in studying the behaviour and performance of grinding circuits by facilitating the evaluation of various scenarios and identification of optimum operating conditions. This technique was applied to the St Andrew Goldfields Ltd.’s Stock Mine Mill which is a 1300 tpd gold milling facility, offering custom milling services as well as processing the Company’s own ores. Lack of adequate instrumentation in the mill poses a challenge in attaining optimum performance especially with changing ore types and characteristics. The grinding process is monitored essentially by manual measurement and adjustment of pulp densities at various streams. A simulation program was designed to assist in the effective implementation of this mode of grinding control. Product sizes from both the primary and secondary grinding circuits were correlated empirically to relevant process variables using a database formed from the results of past sampling campaigns. The simulator was created in Microsoft Excel whose data analysis and optimization tools coupled with its Visual Basic Programming capabilities were found to provide an excellent environment for the development of a cost-effective, efficient and user-friendly simulation program.INTRODUCTIONGrinding is often a very costly unit process in milling operations, mainly due to the excessive energy consumption associated with it. For example, for a Canadian copper-zinc flotation mill, grinding was listed as being the most costly item taking up 30.4% of the total milling expenses, followed by the flotation cost at 2 1 .O% (Kidd Creek Mines Ltd., 1982). A survey on 45 copper flotation mills around the world showed the average grinding cost to be 34.5% of the total milling cost (Weiss, 1985).Overgrinding aggravates the cost issue, while insufficient grinding either causes loss of valuable minerals to tails or results in low-grade concentrates. Therefore, it is essential that grinding circuits be carefully controlled and monitored. To this end, a great deal of effort has been devoted over the years to the modelling and simulation of grinding systems in order to assist in the efficient running of these processes."

Jan 1, 2001

By Pascal Lesagel

Life Cycle Assessment (LCA) is a holistic environmental assessment tool that allows the compilation and evaluation of the inputs, outputs, and potential environmental impacts of a product or service throughout its life cycle, from cradle to grave (i.e., from resource extraction and transformation to final disposal, including production and use stages). The relevance of LCA for the mining industry is twofold. First, the mining industry has a role in providing the LCA community the data that allows subsequent evaluations of the life cycle environmental impacts of primary materials such as metals, as well as the environmental comparison of the downstream products of the mining industry with other competing materials for specific uses. Second, the mining industry can use LCA in order to evaluate the environmental impacts of its activities, identify their environmental hotspots and compare the impacts of available technical options. For example, the environmental impacts of different extractive and processing technology can be compared through the use of LCA. This latter use of LCA by the mining industry is less common. This paper discusses the use of LCA to compare sulphidic tailings management options. The paper also presents some of the LCA research challenges that still have to be addressed to increase the relevance of LCA results for the specific context of mining activities.

Nov 1, 2008

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal, F. A. Muñoz

Different authors and publications indicate that Optibar Segmented Intercell Bars cause a remarkable distortion in the distribution of the current in a cell group. However, these results were based in inaccurate computer based models and do not represent the technology. During the last trimester of 2010, a 92 cells circuit from Barrick Zaldívar EW plant was implemented with Optibar Segmented Intercell Bars. The technology was incorporated progressively without disrupting the plant production. Depending on operational conditions, this led to a 2 to 4% current efficiency increase and 3 to 5% specific energy consumption reduction. By October 2011, 40,000 tons of copper will be produced with the technology.

Jan 1, 2011

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By B. Holaday, H. McLaughlin

Orano Canada Inc. (Orano) operates the McClean Lake mill, located in the Athabasca Basin region of northern Saskatchewan. It processes high concentration uranium ore, delivered in slurry form from the Cameco Corporation operated Cigar Lake mine. After the ore slurry is leached at the McClean Lake mill, the leach residue solids are washed in a process known as counter-current decantation (CCD). This process uses six thickeners to facilitate counter-current washing of solids with diluted acid, flocculation and settling, as well as pumping the washed leach residue to the tailings neutralization circuit (TN), and the uranium laden aqueous to the solvent extraction circuit (SX). Challenges in settling the slurry in CCD started in early 2017. This is largely due to the variation in fines content of the slurry (D80≤75μm), and clay content. There are several changes that have allowed the mill to adapt to the evolving challenges of settling leached Cigar Lake leach residue. Flocculant selection and mixing, temperature effects, bed level management philosophy, and centre-well feed density are key parameters that have been explored as part of adapting to changes in Cigar Lake ore quality.

Jan 1, 2020

By L. Heber Cole

In making this plea for a better and more sympathetic understanding of the non-metallic industry, I do not for one minute wish to give the impression that I in any way belittle the wonderful strides that have been made in the exploitation of our metallics. We in Canada can be justly proud of our Sudburys, Norandas, Flin Fions, and of the remarkable growth of the Consolidated in British Columbia, and at the same time, without in the !east detracting from these worthy undertakings, be equally as proud of our asbestos, gypsum, salt, and coal deposits, as well as of our building-stone and limestone industries. If, in my remarks, I have occasion to compare the metallic with the non-metallic industry, I do so, not with any idea of dimming the glory which the metallics of Canada have gained- not only in our own country, but in the world at large-but for the purpose? of bringing to your attention the fact, perhaps not very well recognized, that Canada contains deposits of non-metallics well worth y of your serious consideration. In the past 33 years, namely, since 1895, the value of non-metallics produced in Canada has exceeded the value of metallics in 19 of the years, and for the last three years has been increasing rapidly. The war years (1915-1918 inclusive) naturally saw an intensive metallic production, but since that time, with the exception of 1925, when there was a general depression throughout the whole country, the non-metallics have been in the ascendency.

Jan 1, 1929

Access to accurate real-time information is critical to maintaining efficiency and competitiveness in any modern minerals processing facility. At MMG LXML Sepon Copper Operation in Lao P.D.R., controlling the copper grade of the feed to the leaching circuit is paramount for maximising productivity and copper recovery. Since 2008, real-time analysis data has been available to process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor. Access to accurate real-time results from the Geoscan has allowed the process engineers to strictly control blending based on copper grade to overcome variability in the plant feed, where conventional sampling and laboratory analysis is difficult, error prone and time consuming. In addition to enjoying these benefits since the Geoscan’s installation, in recent times the process engineers have expanded the use of the Geoscan by observing elemental results other than copper grade to control different aspects of the operation, focussing on the reduction of Gangue Acid Consumption. This paper discusses the process of expanding the Geoscan use at the operation, including an explanation of the calibration process. Additionally, a brief description of the Geoscan and its use at MMG LXML Sepon Copper Operation is provided, as well as a summary of recent calibration and analysis results. A discussion of future works concludes the paper.

Jan 1, 2016