Search Documents

A homely simile will serve to epitomise an interpretation of the rock structures and associated phenomena of the block of country under review, as it appears to the writer.Disregarding the many thousands of feet of overburden that have been eroded away during the ages, the present denuded surface and rock systems below may be pictured as a slab of some titanie ribbon cake that has suffered much damage from rough handling and exposure, yet retaining much of the original symmetry of its superimposed layers of variegated colour and texture.Lateral pressure has crumpled the cake into a series of irregular corrugations and, in parts, has caused some of the layers to crush and slide over their neighbours.Following upon this squeeze, the cake has been severed into segments and rhomboidal slabs by vertical cuts, and these portions have been severely jostled one against its neighbour, crushing the faces of contact and dragging the contiguous layers in the direction of movement.The variegated icing of the cake is represented by intercalated sills of amphibolite, pegmatite, and aplite, and the body of the cake by highly altered sedimentary rocks.The icing has been assailed by the rats of erosion with such effect that only residuals of the original structures remain. The body of the cake has suffered successive waves of igneous invasion in the order of lode pegmatite, followed by zine, iron,copper, and finally by silver-lead. These successive invaders found difficult access, along certain of the vertical cuts, to the more succulent layers of the cake, where, gorging to repletion, many were imprisoned and entombed for the future service of mankind.

Jan 1, 1927

The ready solubility of gold in dilute aqueous solutions of the cyanides of the alkalies or alkaline earths provides a convenient method for the separation of the precious metal -from the large surplus of associated materia1. The finely ground ore is pulped with a weak solution of cyanide, agitated to dissolve the gold, filtered and washed. The lowgrade filtrate is then clarified and the gold precipitated by some electronegative agent, the most usual being finely divided zinc or zinc dust. The slight precipitate is collectedon some form of filter coated with a filter aid, the filter cake being then known as "gold slime".A typical analysis of this slime is given in Table 1.

Jan 1, 1956

Biosorption of Cr(VI), Pb(II) and Zn(II) from Aqueous Solutions by Immobilised Phanerochaete chrysosporium Biomass in a Fixed-Bed Column The continuous-flow adsorption of Cr(VI), Pb(II) and Zn(II) from aqueous solution by immobilised Phanerochaete chrysosporium biomass in a fixed-bed column was studied. The effects of flow rate, influent concentration of Cr(VI), Pb(II) and Zn(II) and bed depth on breakthrough curves and biosorption capacity were investigated. The experimental results showed that the breakthrough time decreased with increasing flow rate, increasing influent concentration and decreasing bed depth. The data also indicated that the equilibrium uptake of Cr(VI), Pb(II) and Zn(II) increased with decreasing flow rate and increasing influent concentration of Cr(VI), Pb(II) and Zn(II). Two models were employed to predict the breakthrough curves and to determine the characteristic parameters of the column useful for column design. The Thomas model was able to predict the breakthrough curve in the range of relative concentration(Co/Ci) higher than0.3, Cr(VI), Pb(II) and Zn(II) whereas the validity of the Bohart-Admas model was limited to the initial part of breakthrough curve at all flow rates and influent concentrations of Cr(VI), Pb(II) and Zn(II). The feasibility of reusing the immobilised fungal beads through five adsorption/desorption cycles in fixed-bed column was investigated.

Sep 13, 2010

If the industry keeps doing what it has always done, it will continue to get what it has always got - rising operating costs. Why is this so? Generally grades being chased are becoming lower, stripping ratios becoming higher, ability to attract personnel to the industry becoming harder and/or more expensive, higher safety standards are being demanded and environmental governance is being enforced.   How then should the surface mining industry plan for the future whilst delivering on improved safety and the environment? In-pit crushing and conveying (IPCC) points the way, as a partial or complete substitute for trucks.   IPCC systems promise significant advantages over traditional truck and shovel operations, including improved safety, reduced operating costs, reduced dust and noise emissions, far greater efficiency in energy use (electric versus diesel motors predominantly and the ability to regenerate electricity back into the local grid for downhill situations), reduced carbon emissions (dependent on power generation source) and reduced water consumption. Despite these advantages, there is a general industry reluctance to migrate from truck and shovel operations. This reluctance stems from a familiarity with truck and shovel operations and a perceived concern that IPCC lacks flexibility which will negatively impact on the mining operation.   In studies conducted since 2007 (with the new modular builds) comparing IPCC with truck-optimised pit designs, IPCC has delivered up to USD$0.82 per tonne moved less than an equivalent truck operation. In addition, IPCC is easily automated from a central control room (local or remote) - something that trucks have yet to commercially achieve.   IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations - its safety, the impact on the environment and its costs. It maybe of interest to note that there is over 200 IPCC installations worldwide today.   This paper and presentation will assist in furthering the understanding of IPCC and its applicability.

Jun 1, 2010

The placer gold industry has experienced a roller-coaster history incorporating four major boom eras. The first, 'hand-methods' boom arose in the mid-19th Century from application of an old idea in new places around the globe. The subsequent hydraulic mining, bucket dredging, and 'hydraulic excavator-portable plant' booms each arose from application of new ideas in old places around the globe, ie in places where gold had been found during earlier booms. The new ideas that heralded the second, third and fourth booms were all significant advances in excavation technology. These enabled the industry to target the known deposits that were too deep, too wet, too small, or too low-grade for recovery by earlier boom methods. Relatively few new deposits or new deposit styles arose from the 'history book' exploration approach, so the number of known deposits to which each of the boom methods were applicable was limited. Consequently, the first three booms were each followed by significant periods of industry decline, and the fourth boom is currently waning inNew Zealand. Further decline is not inevitable and can be avoided by changing to a knowledge-based exploration approach similar to that adopted by the hard rock gold industry in the 1970s. Such an approach could easily herald the next placer gold boom.   Most of the relatively coarse, easily won alluvial gold in proximal and medial reaches of the active placer systems is gone. However, a substantial alluvial gold resource remains in the distal reaches of active systems, and in ancient placers formed onshore and on the continental shelf during previous sedimentary cycles. The resource in these deposits probably exceeds the total New Zealand placer production to date. Successful development of these placers requires application of robust geologic models for the formation and distribution of the placers through time, and advanced exploration technology that has not been used before in New Zealand. Nevertheless, the knowledge and technology required to explore and mine these deposits is available now. Many of these deposits contain a large proportion of problematic gold types that are difficult to recover with the commonly used gravity technology without sustaining significant losses. Despite advances in recovery technology in last few years, too much emphasis is placed on the incorrect assumption that gold size is the primary control on recovery efficiency. Other gold particle parameters, especially particle shape, exert a much greater control on whether gold will be saved or lost to the tails, and must be considered in the design of recovery technology and configuration of recovery circuits.

Jan 1, 2003

The criterion for assessing the accuracy of coal reserve estimates proposed by Philip and Watson (1982) is criticized.Following Royle (1977), it is suggested that the global estimation variance found by geostatistical methods is more appropriate.This method is applied to coal data from the Bowen Basin. This shows that two factors (the inherent variability of the variable under study and the total number of drill holes) have more influence over the accuracy of the reserve estimate than the form of the drilling pattern. Comparisons between the relative errors for different sized regions demonstrate that the spacing between drill holes is of secondary importance. The dominant factor is the total number of holes.Comparisons between the relative errors show that some variables such as sulphur need a much denser sampling than the others to obtain the same level of precision.

Jan 1, 1983

By W Skinner, C G. Kelsey, J R. Kelly

The iron ore industry has reached the end of an unprecedented period of expansion triggered by China’s demand for iron ore. Lower ore prices have led producers to focus on optimising mining operations while extracting the maximum tonnage from the infrastructure presently in place or from projects already underway. A rising global surplus is expected to further force ore prices down and lead to output curtailments, which in turn will help to restore market balance. However, investment in the development of new resources and the development of new infrastructure will inevitably become necessary. Making the right decisions in relation to future processing infrastructure in a climate of uncertain demand and price volatility will not be as straightforward as in the past, where expanding the scale of a proposed operation has been the answer to ensuring economic viability. Overall cost and environmental pressures particularly in relation to wet processing will dominate the decision-making process. IMP Technologies (IMPTEC) has anticipated the need for a dry low cost processing alternative, which can open the way for the development of lower grade magnetite deposits and ensure the sustainability of processing in Australia. The lower grade magnetite deposits are generally fine grained and require grinding to p80 of 30 to 40 microns. Historically, the cost of grinding to these sizes has been and remains a key factor determining the economic viability of a magnetite processing operation. The IMPTEC Super-fine Crusher and Cyclomag Separator are the key components of a proposed radically simplified dry processing alternative, which addresses both cost and environmental issues. This paper reports on the results of pilot super-fine crushing and cyclomag separation test work, focused on supporting the feasibility of the proposed dry processing route for the production of high-grade pellet plant feed from fine grained low-grade magnetic ores.CITATION:Kelsey, C G, Kelly, J R and Skinner, W, 2017. Dry processing of magnetic iron ores – addressing cost and environmental issues, in Proceedings Iron Ore 2017, pp 215–220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Mr Kapp's paper helps considerably to clarify the subsidence/mine geometry relationships in New South Wales. It is in the best tradition of the presentation of field investigations such as has built up internationalknowledge over the years.The Author has plotted in Fig. 10, the maximum subsidence developed over each of a number of panels of different width/depth ratios and concludes that the maximum possible subsidence over a super critical extractionarea is around 0.65 of the mining height and that this is reached with the critical width/depth ratio of extraction of around 1.5.Although, as Mr. Kapp says, the maximum possible subsidence in the UK can reach 90% of the seam thickness extracted the more usual figure for the first seam is up to 80%. It has also been found in the UK that with shallow workings such as those at Kemiro Coliery the critical width of extraction is 2.0 or more times the depth.

Jan 1, 1981

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992

The following notes apply more especially to the purchase of silverlead ores produced in the neighbourhood of Zeehan and Dundas; for it is this class of ore that is principally mined in those parts, and which creates competition among the ore buyers.In the early days of this field, most of the ore passed through the hands of the first buyer who had sufficient enterprise to establish himself at Zeehan but in more recent times, competition has been so keen that there are generally three or four buyers tendering. lf the output was large this would not matter so much from the buyers' point of view but when we consider that the output of the field is only some 1,650 tons per month, and that of this 70 odd tons are produced by the Western and Montana mines, aud being sent home for realization, is withdrawn from local purchasers, there is really not enough for four buyers, especially at the present exorbitant prices they pay the miners.Some of the mines have a fixed sampling day, on which it is tacitly understood that the ore buyers will attend. Others, such as Grubb's Silver Mining Oompany, No-Liability, send round a printed reminder, stating the quantity of ore, and the date of sampling.

By J C. Volkwein, A D. A Hansen, E Sarver, C Barrett

Ensuring that diesel particulate matter (DPM) levels in underground metal and non-metal mines are maintained below statutory limits is an essential requirement of mine ventilation systems. However, despite the cost of providing ventilation, air ventilation rates are usually based upon models, assumptions, or measurements integrated over long durations rather than actual need. Real-time measurement of DPM, interpreted in terms of mine activity schedules, can offer better ventilation management to keep DPM within regulated levels while controlling costs. This work presents data from three demonstration sites with in-mine applications of an environmental particulate sensor that measured black carbon (BC) as a surrogate for DPM.Aethalometers are a class of environmental monitors that measure the light absorbance of aerosol particles at several optical wavelengths. A model AE33 Aethalometer was operated in three separate mines for periods of two weeks, three months, and seven-plus months, and the data was reported in real time as a concentration of BC. Concentration of aromatic organic compounds, which can indicate other forms of combustion, was also reported. The data was used to:- measure the relative efficiency of a new scale-model DPM air scrubber- determine if ventilation could be reduced in a shotcrete loading facility without compromising air quality- evaluate diurnal and weekly DPM levels in a large-entry stone mine. Instrument data were displayed locally and stored for later downloading in all cases. In one mine, the instrument was connected to a local controller, and in another it was connected to the mine’s underground network so that DPM data was presented in real time to a display in the mine ventilation engineering office on the surface.The results showed that the air scrubber removes from 82 per cent to 95 per cent of the DPM; that DPM produced during shotcrete loading is only a minor part of overall DPM levels; and that wide variations in DPM levels exist in the limestone operation. The DPM monitor operated continuously for extended periods in these underground environments. The only maintenance required was the routine replacement of filter tape, typically on a two-week schedule. A sample diluter, which is currently being tested, could extend the intervals between filter changes. The real-time data output of the Aethalometer is appropriate for direct integration into ventilation-on-demand control systems.CITATION:Volkwein, J C, Barrett, C, Sarver, E and Hansen, A D A, 2017. Application of an environmental ‘black carbon’ particulate sensor for continuous measurement of DPM in three underground mines, in Proceedings Australian Mine Vent Conference 2017, pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

In the minerals industry allocating capital for setting up a new project or for upgrading an existing facility usually requires that a compromise be found between the initial cost of equipment, its operating performance and on-going operating costs. To maximise the return on the investment usually requires that various possible combinations and layouts of equipment be assessed. This task is both difficult and time consuming. Computer simulation can be used as a means of determining the expected operating performance of a range of alternate equipment configurations. Simulation is a particularly important technique for analysis as it is one of the few approaches that allows the analyst to take into account the variability inherent in a mining process. While computer simulation is a well established technique its use, until recent years, has been limited to large organisations with access to substantial computing facilities. However, with the current availability of low cost computing platforms combined with easily understood animated displays, simulation is now becoming more widely used across the industry.

Jan 1, 1990

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By S Dunham

A cross-discipline approach combining geology, metallurgy and mine planning, geometallurgy is seen as the next logical advance in improving the design and operation of mining businesses. This rapidly evolving field is focused on realising the value that has often been lost in the chasms between the aforementioned technical silos. When successful, the geometallurgical approach promises the ability to tailor mining and mineral processing development and operational options more closely to the characteristics of the resource with resulting lower costs (both capital and operating), improved recoveries and fewer project failures.As with any technological (or managerial) change, there will be side effects from the success of the geometallurgical approach that will impact areas beyond obvious linkages between geology and processing. Some of these effects have the potential to be beneficial to the resource industry and society in general. Beyond the basic geometallurgical promise of closer alignment between processing design/strategy and the multivariate 3D spatial characteristics of the mineralisation, this paper discusses the broader implications and ramifications of the emergent geometallurgical approach: enhancing exploration and discovery; improving project development success; achieving sustainability in an industry working with non-renewable resources; in a world of increasingly hard won license to operate, improving the management of potentially harmful by-products and waste materials (with knock on effects for proactive management of closure issues); smarter approaches to energy management and thus optimisation of projects with respect to carbon footprint; and potential to re-value assets and thus realise a strategic advantage in the area of acquisitions, divestments, mergers and take overs. The authors strongly believe that companies that actively engage with the above issues (and ensure that technical efforts in the area of geometallurgy are not isolated from the larger value chain activities of the firm) will be able to exploit the opportunities that consequentially arise. These early adopters will gain first mover advantages. Firms taking the broad view of geometallurgy will have an opportunity to maximise stakeholder value and win greater success than their less insightful competitors.

Sep 5, 2011

Australia has a long history of underground mining. Even withadvances in open cut mining equipment, techniques andeconomics, many orebodies are still best mined by undergroundmeans. In addition, modern exploration tools are æuncoveringÆorebodies that are at increasing depths. South African mines arecurrently producing from below 3 km, and developing down to5 km depths û it is likely that Australian mines will also becomemuch deeper over the next 20 years. One of the most significanttechnical challenges in deep mines is the problem of heat.Community expectations and legislated standards continue todrive operations towards improving the working conditions inmines. The hazards and costs associated with chronic hotworking conditions (heat illness, poor safety, poor productivity,higher operating costs and poor morale) are also becomingincreasingly recognised (Brake, Donoghue and Bates, 1998). Theexposure of miners to many other occupational hazards has beenreduced over the past 50 years. However, despite air-conditionedcabins greatly reducing the heat stress on mobile plant operators,there are still many Australian mine workers subject to levels ofthermal stress that existed a century ago. There are severalreasons for this, including a frequently-poor understanding of thephysiology of working in heat by mine management, no agreedmining code of practice for working in heat, the lack of a robust,practical-sized instrument to measure heat stress, the costpressures on the industry and, to some extent, deep-seatedtraditional management and worker practices. Howeversignificant progress has been made in many of these areas (Brakeand Bates, in press), with the net result that there is likely to be a trend towards installation of refrigeration of some form in manyAustralian mines in the future. This will add directly to the costof operation, but will also have direct and indirect benefits,including cost benefits. It should also be noted that Australia isnot at the forefront of adopting practices to manage temperaturesin the workplace: South African metal mines usually haverefrigerated cooling, and Canadian mines spend large sums onheating, with heating costs (averaged over a full year) of up to$A1 per tonne mined (Bandopadhyay et al, 1997). The history of mine refrigeration dates back to 1919 when thefirst plant was installed at Morro Velho, Brazil. By 1965, the totalinstalled capacity (worldwide) reached about 100 MW(R)i. Since 1965 the growth in mine refrigeration capacity has beenexponential, with a doubling every six or seven years (Howes andNixon, 1997). South Africa is by far the largest user of minerefrigeration, with over 300 refrigeration machines installed. This paper discusses the key design issues associated with theapplication of refrigeration in underground metal or coal mines.Whilst the emphasis is on large, surface plants, small, surface orunderground refrigeration plants can also be very effective in thecorrect application and many of the principles of design andoperation are the same.

Jan 1, 2001

By R Fury, I Skepper, D White, G Miller

Although the Pressure Acid Leaching (PAL) of nickel laterites has been conducted at Moa Bay, Cuba, since the early 1960s, the commissioning delays generally encountered by the æsecond generationÆ of PAL lateritic nickel producers in the late 1990s have demonstrated the potential complexity of the PAL process and the importance of technical risk management in maximising the realised project value. This paper describes some of the strategies used by the Ravensthorpe Nickel Project (RNP) to manage the technical aspects of the Ravensthorpe project risk. Central to these strategies is the use of Front End Loading (FEL) to deal with issues early in the development phase, when changes to the project structure can be made most effectively and cheaply. Such an approach requires a management philosophy that recognises risk as a potential cost, which accepts responsibility for dealing with risk, and which is prepared to provide adequate resources for risk management.

Jan 1, 2004

Holla has given a good background to the various methods of subsidence control in the coalfields around Sydney.The present writer notes that in many cases, especially with wide longwall panels, there is not the flexibility to alter the mine layout as there is to some degree with the various pillar extraction methods. For this reason it may not be possible to plan the workings to minimise subsidence and some damage to structures may occur. The cost of repair or the cost of subsidence provisions to minimise damage may be small in relation to the tonnages of coal which would otherwise have to be sterilised. One method of subsidence control which has been in use in the Newcastle area since 1970 is the panel and pillar layout (partial extraction layouts with stable pillars). An extracted panel width of 0.6 times the depth of cover resulted in a maximum subsidence of 115 mm for an extracted seam thickness of 2.2 m.As Holla points out, the extracted panel widths in relation to th depth of cover depend on the particular geological setting. His Fig. 3 shows that the subsidence over a panel width of 0.3 times the cover depth in the Southern Coalfield is the same as over a panel width of 0.55 to 0.6 times the cover depth in the Northern Coalfield.Selective pillar extraction and longwall mining can both be used in the panel and pillar layout. Holla's Figs 2 and 3 are used to estimate the maximum subsidence over an extracted panel of known geometry. Maximum subsidence is related to seam thickness. What provision is made for a reduction in subsidence due to the coal which remains behind in a pillar extraction panel if the pillar recovery is poor? The writer suggests that an effective seam height could be used, based on the actual mining height reduced by a factor to account for the percentage recovery of coal from an extracted panel.

Jan 1, 1986

Study on Dynamic Characteristics of Inertia Cone Crusher and Its Application

Sep 13, 2010

Effects of High Pressure Grinding Rolls on Platinum-Bearing Ores and the Flotation Response as Compared to the Conventional Ball Mill Three major PGM ore types from the Bushveld Complex of South Africa: Merensky, UG2 and Platreef were comminuted with the use of the high pressure grinding rolls (HPGR). The influence of the feed characteristics and the various operational and design features of the HPGR on energy consumption, throughput, mineral liberation and PGM flotation recovery were investigated. The test work variables included two feed top sizes of 12 mm and 6 mm, specific grinding forces ranging between 3 - 7.5N/ mm2 and zero gaps of 1.5 mm and 3 mm. The results show that the influence of the HPGR operational and design features on energy consumption, throughput, mineral liberation and PGM recovery are ore dependent. The size reduction-specific energy relationships show that the most energy efficient utilisation of the HPGR for Platreef ore was at the lower specific grinding force of 3N/mm2 and the zero gap at 3 mm. For Merensky and UG2 ore on the other hand, the most energy efficient operation was at the higher specific grinding force of 7.5N/mm2 and the zero gap of 1.5 mm. At a specific energy input of 3 kWh/t, reduction ratios (F50/P50) of 6.5, 3.8 and 10 were obtained for Merensky, UG2 and Platreef, respectively for feed top sizes of 12mm. Further application of the HPGR as a pregrinding stage to a ball mill showed a 25 - 30 per cent increase in throughput for Merensky and UG2 ore. Batch flotation tests performed on selected samples appear to indicate that ore comminuted with the ball mill had superior grades compared with that ground with the HPGR. However, Merensky and UG2 ore comminuted at different HPGR operating conditions showed distinctions in PGM recovery. Platreef on the other hand did not appear to show any differences. Therefore, this study highlights the significance of ore type and operating variables in HPGR applications with regards to energy efficiency, throughput and PGM recovery.

Sep 13, 2010

By Chand F

The silver deposits of Rockvale near Armidale, N.S.W., occur in fissure veins in epi-Permian granite. The ore is fine grained, mineralogically complex, and contains twenty-seven different minerals including eleven silver minerals. The ore is characterized by a unique multiple unmixing from a sphalerite solvent. The following minerals have exsolved from solid solution in sphalerite: pyrrhotite, chalcopyrite, cubanite I, cubanite II (chalcopyrrhotite), valleriite, "brown" stannite, "olive" stannite, argentian tetrahedrite, pyrargyrite, and an unknown grey-white mineral. Several of these minerals derive from a second-stage unmixing, the immediate solvents of which are the products of earlier exsolutions.INTRODUCTIONSmall silver-rich base metal deposits occur at several localities near Armidale in the New England district of New South Wales. Chief among these are the Tulloch Mine and the Rockvale Mine at Rockvale, 27 miles SE. of Armidale, and the Tait's Gulley deposits some 15 miles NE. of Armidale.At Rockvale (Kenny, 1928), irregular lenses of lode material, principally quartz and calcite, occur along a zone of shearing in biotite granite and altered sediments. The orebodies had a maximum width of 6 ft but averaged 2 ft 6 in. The largest lens was 150 ft long and 50 ft high. The Rockvale deposits were worked for both arsenic and silver; 2,897 tons of arsenic were produced but no figures are available forsilver.Little is known of the Tait's Gulley deposits which occur in folded arenites containing small but rich veins of pyrargyrite with base metal sulphides.The sediments in these localities are possibly Silurian.

Jan 1, 1962